2ADAO-KHWSN301F001Dispensor Beacon ES10

DISPENSER BEACON ES10 - USER MANUAL Visit start.kontakt.io to create a customer account and add your devices to the customer panel using your Order ID. Download the app and activate your Dispenser Beacon ES10. Follow the instructions in the Kontakt Device Manager mobile app to configure your Dispenser Beacon ES10. Frequency (MHZ): 2402.0 - 2480.0 Maximum RF power: +4dBm (2.5 mW) ES10 Dispenser Beacon is attached as a SmartLink module to the Gojo ES10 soap/sanitizer dispenser. It is a dispense event sensor used to monitor hand hygiene compliance in Healthcare facilities. Battery: 4x ER14250 3.6V, total capacity 10800 mAh. Kontakt Micro-Location Sp. z o.o. ul. Stoczniowców 3 30-709 Kraków POLAND, hereby declares that this device is in compliance with Directive 2014/53/EU. EU Declaration of Conformity: https://kontakt.io/compliance-dispenser-beacon-es10 Manufactured for: Kontakt Micro-Location Sp. z o.o. ul. Stoczniowców 3 30-709 Kraków POLAND PNR: KHWSN301F001 DISPENSER BEACON ES10 - INSTRUKCJA UŻYTKOWANIA Odwiedź stronę start.kontakt.io, aby zalogować się konto klienta i dodać swoje urządzenia do panelu klienta za pomocą Order ID. Pobierz aplikację i aktywuj swój Dispenser Beacon ES10. Postępuj zgodnie z instrukcjami w aplikacji mobilnej Kontakt Device Manager, aby skonfigurować Dispenser Beacon ES10. Częstotliwość (MHz): 2402.0 - 2480.0 Maksymalna moc radiowa: +4dBm (2.5 mW) ES10 Dispenser Beacon jest montowany jako moduł SmartLink do dozownika mydła/środka dezynfekującego Gojo ES10. Jest to czujnik zdarzeń dozowania służący do monitorowania zgodności z zasadami higieny rąk w placówkach ochrony zdrowia. Bateria: 4x ER14250 3,6V, łączna pojemność 10800 mAh. Kontakt Micro-Location Sp. z o.o. ul. Stoczniowców 3 30-709 Kraków POLSKA niniejszym oświadcza, że niniejsze urządzenie jest zgodne z dyrektywą 2014/53/UE. Deklaracja zgodności UE: https://kontakt.io/compliance-dispenser-beacon-es10 Wyprodukowano dla: Kontakt Micro-Location Sp. z o.o. ul. Stoczniowców 3 30-709 Kraków POLSKA PNR: KHWSN301F001 This device complies with part 15 of the FCC Rules. Operation is subject to the following two conditions: (1) This device may not cause harmful interference, and (2) this device must accept any interference received, including interference that may cause undesired operation. FCC warning: Any Changes or modifications not expressly approved by the party responsible for compliance could void the user's authority to operate the equipment. Note: This equipment has been tested and found to comply with the limits for a Class B digital device, pursuant to part 15 of the FCC Rules. These limits are designed to provide reasonable protection against harmful interference in a residential installation. This equipment generates uses and can radiate radio frequency energy and, if not installed and used in accordance with the instructions, may cause harmful interference to radio communications. However, there is no guarantee that interference will not occur in a particular installation. If this equipment does cause harmful interference to radio or television reception, which can be determined by turning the equipment off and on, the user is encouraged to try to correct the interference by one or more of the following measures: -Reorient or relocate the receiving antenna. -Increase the separation between the equipment and receiver. -Connect the equipment into an outlet on a circuit different from that to which the receiver is connected. -Consult the dealer or an experienced radio/TV technician for help. This equipment complies with FCC radiation exposure limits set forth for an uncontrolled environment. This equipment should be installed and operated with minimum distance 20cm between the radiator & your body.

Kontakt Micro-Location Sp. z o.o. 2.911 (d)(5)(i) Equipment Type Attestation v1.2 Section 2.911(d)(5)(i) Certification – Equipment Type Company name: Kontakt Micro-Location Sp. z o.o. Address: ul.Stoczniowcow 3, 30-709 Krakow, Poland Product Name: : Dispensor Beacon ES10 FCCID: 2ADAO-KHWSN301F001 Model(s): KHWSN301F001 2.911(d)(5)(i) Equipment Type We, [Kontakt Micro-Location Sp. z o.o.] (“the applicant”) certify that the equipment for which authorization is sought through certification is not:  Prohibited from receiving an equipment authorization pursuant to § 2.903; of the FCC rules.  Identified as an equipment type in the “Covered List” NOTE 1 Yours sincerely, Name: Joanna Wolczanska Date:2026/06/22 Title and Company name: Ms/Kontakt Micro-Location Sp. z o.o. NOTE 1 “Covered List”; is the List of Equipment and Services Covered By Section 2 of The Secure Networks Act, available at https://www.fcc.gov/supplychain/coveredlist References; 1) 986446 D01 Covered Equipment v01 https://apps.fcc.gov/oetcf/kdb/forms/FTSSearchResultPage.cfm?switch=P&id=325672 2) Federal Register document 2022-28263 published on 02/06/23 https://www.federalregister.gov/documents/2023/02/06/2022-28263/protecting-against-national-security-threats-to-the-com munications-supply-chain-through-the

KontaktMicro-LocationSp.zo.o. 2.911(d)(5)(ii)ApplicantAttestationv1.2 Section2.911(d)(5)(ii)Certification–Applicant(CoveredList) Companyname:KontaktMicro-LocationSp.zo.o. Address:ul.Stoczniowcow3,30-709Krakow,Poland ProductName::DispensorBeaconES10 FCCID:2ADAO-KHWSN301F001 Model(s):KHWSN301F001 2.911(d)(5)(ii)Applicantfiling We,[KontaktMicro-LocationSp.zo.o.](“theapplicant”)certifythat,asofthedateofthefilingof theapplication,theapplicantisnotidentified NOTE1 onthe“CoveredList” NOTE2 ,establishedpursuantto §1.50002ofthischapter,asanentityproducingcoveredcommunicationsequipment. Yourssincerely, Name:JoannaWolczanskaDate:2026/06/22 TitleandCompanyname:Ms/KontaktMicro-LocationSp.zo.o. NOTE1 Deleteoptionnotapplicabletothisapplication. NOTE2 “CoveredList”;istheListofEquipmentandServicesCoveredBySection2ofTheSecureNetworksAct,availableat https://www.fcc.gov/supplychain/coveredlist References; 1)986446D01CoveredEquipmentv01 https://apps.fcc.gov/oetcf/kdb/forms/FTSSearchResultPage.cfm?switch=P&id=325672 2)FederalRegisterdocument2022-28263publishedon02/06/23 https://www.federalregister.gov/documents/2023/02/06/2022-28263/protecting-against-national-security-threats-to-the-com munications-supply-chain-through-the Docusign Envelope ID: 4601A4B9-B3AD-810F-8386-44B6A220270C

U.S.AgentDesignationforServiceofProcess (ApplicantandU.S.AgentareSeparateParties) TO:FederalCommunicationsCommission 7435OaklandMillsRoad Columbia,MD21046 TheApplicantacknowledgesthattheymustmaintainanagentfornolessthanoneyearafterterminatingall marketingandimportationORtheconclusionofanyCommission-relatedproceedinginvolvingthe equipment.TheapplicantfurtheracknowledgestheirresponsibilitytoinformtheFCCwheneverthe DesignatedU.S.Agentinformationabovechanges. Applicant Companyname:KontaktMicro-LocationSp.zo.o ATTENTION:FCCCertification–Section2.911(d)(7)Information DesignatedU.S.Agent CompanyName:BaihetianInnovativeSolutions Address:6837ChaseRd,Dearborn,M148126 FRN:0033401605 ContactName:KennethYoung Tel.:313-395-3113 Email:[email protected] Thisletteristoconfirmthatwe(“theDesignatedU.S.Agent)haveacceptedtheresponsibilitytoactasthe DesignatedU.S.AgentforServiceofProcessasrequiredbysection47CFR2.911(d)(7)onbehalfofthe Applicantnotedbelow. U.S.AgentSignature: Date:2026.6.22 Signedby(PrintedName/Title):KennethYoung . GranteeCode:2ADAO FCCID:2ADAO-KHWSN301F001 ContactName:JoannaWolczanska StreetAddress:ul.Stoczniowcow3Krakow,30-709Poland TelephoneNo:0048123793445 Email:[email protected] FRN:0023964000 ApplicantSignature: Date:2026-6-22 Signedby(PrintedName/Title):JoannaWolczanska/Ms Docusign Envelope ID: 4601A4B9-B3AD-810F-8386-44B6A220270C

KontaktMicro-LocationSp.zo.o. Company:KontaktMicro-LocationSp.zo.o. Address:ul.Stoczniowcow3,30-709Krakow,Poland ProductName::DispensorBeaconES10 FCCID:2ADAO-KHWSN301F001 Model(s):KHWSN301F001 WeauthorizeMiCOMLabsInc.,575BoulderCourt,Pleasanton,California94566,USA, toactonourbehalfonallmattersconcerningthecertificationofabovenamed equipment. WedeclarethatMiCOMLabsInc.isallowedtoforwardallinformationrelatedtothe approvalandcertificationofequipmenttotheregulatoryagenciesasrequiredandto discussanyissuesconcerningtheapprovalapplication.Anyandallactscarriedoutby MiCOMLabsonourbehalfshallhavethesameeffectasactsofourown. Signature:Date:2026/06/22 Name:JoannaWolczanska Title:Ms Company:KontaktMicro-LocationSp.zo.o. Docusign Envelope ID: 4601A4B9-B3AD-810F-8386-44B6A220270C

Kontakt Micro-Location Sp. z o.o. Office of Engineering Technology Federal Communications Commission 7435 Oakland Mills Road Columbia, MD 21046 USA Date: 2026/06/22 Subject; Request for Confidentiality FCC ID: 2ADAO-KHWSN301F001 To Whom It May Concern, Pursuant to the provisions of the Commission’s rules Title 47 Sections §0.457 and §0.459, we are requesting the Commission to withhold the following attachment(s) as confidential documents from public disclosure indefinitely. These documents contain detailed system and equipment descriptions and are considered as proprietary information in operation of the equipment. The public disclosure of these documents might be harmful to our company and would give competitors an unfair advantage in the market. Schematic Diagram Block Diagram Operational Description In additional to above mentioned documents, in order to comply with the marketing regulations in Title 47 CFR §2.803 and the importation rules in Title 47 CFR §2.1204, while ensuring that business sensitive information remains confidential until the actual marketing of newly authorized devices, we request Short Term Confidentiality of the following attachment(s); User Manual For 45 days, pursuant to Public Notice DA 04-1705. OR For 180 days pursuant to KDB 726920 D01. It is our understanding that all measurement test reports, FCC ID label format and correspondence during the certification review process cannot be granted as confidential documents and this information will be available for public review once the grant of equipment authorization is issued. Sincerely, Signature: Name: Joanna Wolczanska Title: Ms

External Photos

部品料号 NO. 年.月.日 版本 变 更 记 录 签 名 未标公差 ±0.1 ±0.12 ±0.2 ±0.4 ±0.5 L≦4 4＜L≦16 16＜L≦63 63＜L≦250 250＞L 表面处理 材 质 颜 色 1 2 3 单位: mm 比例:1/1 结 构 年.月.日 V007 Y-YB-CR-065 密级：绝密 部品名称 版 本 部品规格书 认证 生效日期 供应商 美 工/硬件 审 核 NPI 4 LAB值 *重点标注尺寸 FCC ID: 2ADAO-KHWSN301F001 MAC: 1A:2B:3C:4D:5E:6F Unique ID: 16abcdef Dispenser Beacon ES10 PNR: KHWSN301F001 Patent # US-11816524-B2 Designed by Kontakt.io in the USA Poppins 4.0pt

Internal Photos ANT

FCC ID:2ADAO-KHWSN301F001 RF EXPOSURE EVALUATION According to FCC 1.1310: The criteria listed in the following table shall be used to evaluate the environment impact of human exposure to radio frequency (RF) Radiation as specified in §1.1307(b) Limits for Maximum Permissible Exposure (MPE) f = frequency in MHz. * = Plane-wave equivalent power density. 11.1 Friis transmission formula: Pd= (Pout*G)\ (4*pi*R 2 ) Where Pd= Power density in mW/cm 2 Pout=output power to antenna in mW G= Numeric gain of the antenna relative to isotropic antenna Pi=3.1416 R= distance between observation point and center of the radiator in cm Pd the limit of MPE, 1mW/cm 2 ,If we know the maximum gain of the nd total power input to the antenna, through the calculation, we will know the distance where the MPE limit is reached. RF Exposure Information: The radiated output power of this device meets the limits of FCC/IC radio frequency exposure limits.This device should be operated with a minimum separation distance of 20cm (8 inches) between the equipment and a person's body. 11.2 Measurement Result WIFI2.4G and Bluetooth cannot transmit at the same time BLE Antenna gain: 3.24dBi modulation Channel Freq. (MHz) Measured power (dBm) Tune-up power (dBm) Max tune- up power (dBm) Antenna Gain Numeric Evaluation result (mW/cm2 ) Power density Limits (mW/cm2 ) BLE 2440 4.3 3 to 5 5 2.11 0.0013 1

ShenzhenMinewTechnologiesCo.,Ltd.V001Y-YB-CR-150 Confidentialitylevel:Secret 1st ProjectNoP25152B5DPCBVersionLO036F6_V0.3 TesterXuNingDate2026.1.27 AuditingDate ApprovalDate AntennaTestReport ShenzhenMinewTechnologiesCo.,Ltd.V001Y-YB-CR-150 Confidentialitylevel:Secret 2nd Contents 1.ProjectInformation.................................................................................................................3rd 2.TechnicalSpecification............................................................................................................4th 3.Theshapeandsizeoftheantenna.........................................................................................5th 4.Theresultofthetest...............................................................................................................5th 4.1.VSWR&Returnloss&Smith......................................................................................5th 4.2.AntennaGainandEfficiency.......................................................................................6th 4.3.RadiationPattern........................................................................................................9th ShenzhenMinewTechnologiesCo.,Ltd.V001Y-YB-CR-150 Confidentialitylevel:Secret 3rd 1．ProjectInformation 1.1.AntennaCoding ： ANT-BBNCNC25033 1.2.AntennaType ： OnboardPCBAntenna 1.3.ModeloftheDUT ： KHWSN301F001 1.4.TestData ： 2026.1.27 1.5.Productpicture ： Product appearance PCBboardand antenna ShenzhenMinewTechnologiesCo.,Ltd.V001Y-YB-CR-150 Confidentialitylevel:Secret 4th 2．TechnicalSpecification ElectricalSpecifications FrequencyRange2400-2480MHz PeakGain3.24dBi Efficiency55% ReturnLoss≤-10dB VSWR≤2.0 Bandwidth(S11≤-10dB)80MHz InputImpedance50 Ω RadiationdirectionOmni PolarizationTypeLinear LightningProtectionDCgrounding PowerCapacity 1000mW（30dBm） MechanicalSpecifications AntennaSize22.3x5.6mm CoreRadiatorCopper SubstratematerialFR4 Substratethickness1mm±0.02mm CoaxialwireNotRequired ConnectTypeNotRequired OperatingTemperature -20to+60°C StorageTemperature -10to+60°C ShenzhenMinewTechnologiesCo.,Ltd.V001Y-YB-CR-150 Confidentialitylevel:Secret 5th 3．Theshapeandsizeoftheantenna Unit：mm 4．Theresultofthetest 4.1.VSWR&Returnloss&Smith Frequency(MHz)ReturnLoss(dB)VSWR 2402-19.41.2 2440-25.41.1 2480-20.71.2 Bandwidth(S11≤-10dB)300 ShenzhenMinewTechnologiesCo.,Ltd.V001Y-YB-CR-150 Confidentialitylevel:Secret 6th 4.2.AntennaGainandEfficiency 4.2.1.Productcoordinateaxisposition Insidethemicrowaveanechoic chamber Productcoordinateaxisposition ShenzhenMinewTechnologiesCo.,Ltd.V001Y-YB-CR-150 Confidentialitylevel:Secret 7th 4.2.2.GainandEfficiencydatesheet ShenzhenMinewTechnologiesCo.,Ltd.V001Y-YB-CR-150 Confidentialitylevel:Secret 8th 4.2.3.GraphsofGainandEfficiency ShenzhenMinewTechnologiesCo.,Ltd.V001Y-YB-CR-150 Confidentialitylevel:Secret 9th 4.3.RadiationPattern 4.3.1.3DRadiationPattern 2402MHz 2440MHz 2480MHz ShenzhenMinewTechnologiesCo.,Ltd.V001Y-YB-CR-150 Confidentialitylevel:Secret 10th 4.3.2.2DRadiationPattern E1，XZ-Face，phi=0°;（E1，theta=0~360°，phi=0°） E2，YZ-Face，phi=90°;（E2，theta=0~360°，phi=90°） H，XY-Face，theta=90°;（H，phi=0~360°，theta=90°）

No.：BCTC/KJ-RF-ICT-001 Page 1 of 52 Edition：B.1 TEST REPORT Shenzhen BCTC Technology Co., Ltd. Report No.: BCTC2605417490E Applicant: Kontakt Micro-Location Sp. z o.o. Product Name: Dispensor Beacon ES10 Test Model: KHWSN301F001 Tested Date: 2026-07-22 to 2026-07-31 Issued Date: 2026-08-19 Report No.: BCTC2605417490E No.：BCTC/KJ-RF-ICT-001 Page 2 of 52 Edition：B.1 FCC ID:2ADAO-KHWSN301F001 The test report is effective only with both signature and specialized stamp.This result(s) shown in this report refer only to the sample(s) tested. Without written approval of Shenzhen BCTC Technology Co., Ltd, this report can’t be reproduced except in full.The tested sample(s) and the sample information are provided by the client. Product Name: Dispensor Beacon ES10 Trademark: Kontakt.io Model/Type Ref.: KHWSN301F001 Prepared For: Kontakt Micro-Location Sp. z o.o. Address: ul.Stoczniowcow 3, 30-709 Krakow, Poland Manufacturer: Kontakt Micro-Location Sp. z o.o. Address: ul.Stoczniowcow 3, 30-709 Krakow, Poland Prepared By: Shenzhen BCTC Technology Co., Ltd. Address: Room 101M, Unit 1, Building1, Pengyuan, No.18, Lilang Road, Shanglilang, Nanwan Subdistrict, Longgang District, Shenzhen, Guangdong, China. Sample Received Date: 2026-07-22 Sample tested Date: 2026-07-22 to 2026-07-31 Report No.: BCTC2605417490E Test Standards: FCC 47 CFR Part 15 Subpart C (clause 15.247) ANSI C63.10-2020 Test Results: PASS Remark: This is Bluetooth BLE radio test report. Prepared by : Reviewer by : Approved by: Mike Zheng Louis Zeng Sewen Guo Report No.: BCTC2605417490E No.：BCTC/KJ-RF-ICT-001 Page 3 of 52 Edition：B.1 Table of Content Test Report Declaration Page 1. Version .................................................................................................................. 5 2. Test Summary ....................................................................................................... 6 3. Measurement Uncertainty ..................................................................................... 7 4. Product Information And Test Setup ..................................................................... 8 4.1 Product Information ............................................................................................... 8 4.2 Test Setup Configuration ...................................................................................... 9 4.3 Support Equipment ............................................................................................... 9 4.4 Channel List ........................................................................................................ 10 4.5 Test Mode ........................................................................................................... 10 4.6 Table Of Parameters Of Text Software Setting ................................................... 10 5. Test Facility And Test Instrument Used ............................................................... 11 5.1 Test Facility ......................................................................................................... 11 5.2 Test Instrument Used .......................................................................................... 11 6. Conducted Emissions .......................................................................................... 13 6.1 Block Diagram Of Test Setup .............................................................................. 13 6.2 Limit .................................................................................................................... 13 6.3 Test procedure .................................................................................................... 13 6.4 EUT Operating Conditions .................................................................................. 13 6.5 Test Result .......................................................................................................... 14 7. Radiated Emissions ............................................................................................. 15 7.1 Block Diagram Of Test Setup .............................................................................. 15 7.2 Limit .................................................................................................................... 16 7.3 Test procedure .................................................................................................... 17 7.4 EUT operating Conditions ................................................................................... 18 7.5 Test Result .......................................................................................................... 19 8. Radiated Band Emission Measurement and Restricted Bands Of Operation ...... 23 8.1 Block Diagram Of Test Setup .............................................................................. 23 8.2 Limit .................................................................................................................... 23 8.3 Test Procedure ................................................................................................... 24 8.4 EUT Operating Conditions .................................................................................. 24 8.5 Test Result .......................................................................................................... 25 9. Power Spectral Density Test ............................................................................... 26 9.1 Block Diagram Of Test Setup .............................................................................. 26 9.2 Limit .................................................................................................................... 26 9.3 Test procedure .................................................................................................... 26 9.4 EUT Operating Conditions .................................................................................. 26 9.5 Test Result ...............................................…

Text truncated - open the document above for the full version.

TEST SETUP PHOTOGRAPHS 1.1. Photos of Radiation Emission Measurement Radiated Measurement Photos RF conducted test ----------------The end----------------