2ADIW-HL-6110HMassage chair

NOUHAUS LIFESTYLE MASSAGE CHAIR USER MANUAL Classic N-0003H Thank you for purchasing NOUHAUS LIFESTYLE MASSAGE CHAIR. Please read this manual carefully before using. Retain this manual for your reference. This User manual contains the product warranty information. This product is intended for a home-use only. It is not intended for commercial or industrial purposes. Do not use as such. The design and/or specifications of this product are subject to change without notice. This product is intended to be used exclusively with 120V. Please make sure to plug the power plug into a dedicated 120V outlet. Using a 110V transceiver to 120V may be dangerous. DO NOT USE in such a manner. NOUHAUS LIFESTYLE MASSAGE CHAIR USER MANUAL Classic N-0003H Classic N-0003H Safety Precautions How to Assemble Components Bluetooth Connection Guide Remote Control Button and Usage Method Cleaning and Storage Method Troubleshooting FAQ Specification Customer Service Information Product Warranty FCC Warning CONTENTS 01 02 03 04 05 06 07 08 09 10 11 12 GF Please adhere closely to the following safety precautions to ensure that your product is used properly and safely. During installation Do not modify, disassemble or repair other than service provider. It may cause fire/electric shock. Use on a flat surface. It may cause failure or accident. Power-related If it does not turn on or cause an error, immediately unplug the power connected to the outlet and request for after-service care. It may cause an electric shock, short circuit, or fire. Make sure the upholstery is not torn or stripped in appearance. The material may get caught in the massage mechanism which may result in a serious accident. If there is any damage, please contact the support center. It may cause electric shock or injury. Do not allow children to touch the power plug. There is a risk of electric shock or injury. Do not bend the power plug too hard or break it by pressing it against any heavy object. Risk of fire and electric shock. Do not use multiple devices simultaneously when using a multi outlet adapter. Risk of fire due to overheating of the outlet. When disconnecting the power plug, hold the plug and Do not pull from the wire. If the power cord becomes torn or damaged, there is a risk of fire and electric shock. Remove any contaminant, moisture, etc from the pins of the power plug. It may cause electric shock / fire. Safety Precautions 01 GF Do not touch the power plug with wet hands. Always disconnect the power plug when cleaning. There is a risk of electric shock. This product is intended to be used exclusively with 120V. Risk of fire due to the high heating of the outlet. Be sure to use a ground-type outlet when using the multi-tap. Use of non-grounded multitap-outlets can cause electric shock and injury. In the event of power failure, immediately turn off the power switch and unplug the power from the outlet. It may cause accidents when the power is turned on again. When in Usage For safety reasons, persons with the following conditions or ailments should not use this product. · People with thrombosis, embolism, severe venous, acute venous, etc. · A person suspected of having whiplash. · A person with symptoms of a sudden contraction of a spasm or muscle. · A pregnant woman in the early stages of pregnancy or right after childbirth. · A person with an abnormality in the spine or misaligned to the left or right due to accidents or diseases. · People with acute appendicitis and severe heart failure. · People who are using human implanted electronic medical devices such as implanted heartbeats. · A person with seizures or a psychogenic disease. · A person who has lost a sense of temperature due to a high degree of peripheral circulation from diabetes, etc. · A person with an osteomyelitis. Classic · IH · A Person who is not free of expression and movement of their body. · Someone with spine symptoms or under spine treatment. · A person who is being treated at a medical institution because of a special physical defect. Persons with any of the following conditions should consult a physician before using this product. · People who are concerned about side effects from the use of this product such as pregnant women. · A person whose body temperature is higher than normal due to acute inflammation. · People with skin disease, malignant tumors, and other symptoms of skin disease. · Someone who needs stability because they are being treated by a doctor. · Other people who feel an abnormality in their bodies. · A person whose doctor forbade massage. · A person or a person with weak muscles due to older age. · A person with back pain. Do not use or store in humid areas such as bathrooms. It may cause electric shock, fire, failure, and mold. Do not allow children to play or climb on the massage chair. There is a risk of falling or injury. Do not wear anything hard on your head, such as headgear. It may cause injury. Use time is 30 minutes per day, 15 minutes per usage, and only 5 minutes for continuous use in the same area. Long-term use can strain muscles or nerves. IH If you experience any of the following side effects while using the product, please stop using it : · Posture damage, bruises, stab wounds, cuts from the product. · Excessive usage of this product can cause damage to muscles and tendons, nerves, vertebrae, etc. · Skin disease, burns, etc. · Fractures, bone dislocation, abrasion, etc. · Respiratory system failure and suffocation, etc. When massaging your hips and thighs, take out all objects out of your pants pocket. There may be an accident or injury. During the massage operation, do not disconnect power from the outlet or turn the power switch on/off. It may cause an accident. Do not use it near fireplaces, or while smoking. Also, do not use it with heating appliances such as an electric pad. It may cause a fire. Do not use it after drinking alcohol. There may be an accident or injury. Do not allow more than one person to get on the prod…

Text truncated - open the document above for the full version.

Henglin Home Furnishings Co., Ltd. Agent Authorization Company: Henglin Home Furnishings Co., Ltd. Address: No.378,380, Jiaxi Road, Dipu Street, Anji County, Huzhou, Zhejiang Product Name: Massage chair Trade Mark: NOUHAUS Model Number(s): N-0003H FCC ID: 2ADIW-HL-6110H We authorize MiCOM Labs Inc., 575 Boulder Court, Pleasanton, California 94566, USA, to act on our behalf on all matters concerning the certification of above named equipment. We declare that MiCOM Labs Inc. is allowed to forward all information related to the approval and certification of equipment to the regulatory agencies as required and to discuss any issues concerning the approval application. Any and all acts carried out by MiCOM Labs on our behalf shall have the same effect as acts of our own. Signature: Date: 2021-11-02 Name: XueDong Deng Title: Certification engineer Company: Henglin Home Furnishings Co., Ltd.

Henglin Home Furnishings Co., Ltd. Office of Engineering Technology Federal Communications Commission 7435 Oakland Mills Road Columbia, MD 21046 USA Date:2021-11-02 Subject; Request for Confidentiality FCC ID: 2ADIW-HL-6110H To Whom It May Concern, Pursuant to the provisions of the Commission’s rules Title 47 Sections §0.457 and §0.459, we are requesting the Commission to withhold the following attachment(s) as confidential documents from public disclosure indefinitely. These documents contain detailed system and equipment descriptions and are considered as proprietary information in operation of the equipment. The public disclosure of these documents might be harmful to our company and would give competitors an unfair advantage in the market. Schematic Diagram Block Diagram Parts List Operational Description Tune-up Procedure Declaration of Software Security Requirements For U-NII Devices In additional to above mentioned documents, in order to comply with the marketing regulations in Title 47 CFR §2.803 and the importation rules in Title 47 CFR §2.1204, while ensuring that business sensitive information remains confidential until the actual marketing of newly authorized devices, we request Short Term Confidentiality of the following attachment(s); External Photos Test Setup Photos Internal Photos User Manual For 45 days, pursuant to Public Notice DA 04-1705. OR For 180 days pursuant to KDB 726920 D01. It is our understanding that all measurement test reports, FCC ID label format and correspondence during the certification review process cannot be granted as confidential documents and this information will be available for public review once the grant of equipment authorization is issued. Sincerely, Signature: Name: XueDong Deng Title: Certification engineer

Shenzhen LCS Compliance Testing Laboratory Ltd. FCC ID: 2ADIW-HL-6110H ________________________________________________________________________________ _________ This report shall not be reproduced except in full, without the written approval of Shenzhen LCS Compliance Testing Laboratory Ltd. Page 1 of 5 EXTERIOR PHOTOGRAPHS Fig. 1 Fig. 2 Shenzhen LCS Compliance Testing Laboratory Ltd. FCC ID: 2ADIW-HL-6110H ________________________________________________________________________________ _________ This report shall not be reproduced except in full, without the written approval of Shenzhen LCS Compliance Testing Laboratory Ltd. Page 2 of 5 Fig. 3 Fig. 4 Shenzhen LCS Compliance Testing Laboratory Ltd. FCC ID: 2ADIW-HL-6110H ________________________________________________________________________________ _________ This report shall not be reproduced except in full, without the written approval of Shenzhen LCS Compliance Testing Laboratory Ltd. Page 3 of 5 Fig. 5 Fig. 6 Shenzhen LCS Compliance Testing Laboratory Ltd. FCC ID: 2ADIW-HL-6110H ________________________________________________________________________________ _________ This report shall not be reproduced except in full, without the written approval of Shenzhen LCS Compliance Testing Laboratory Ltd. Page 4 of 5 Fig. 7 Fig. 8 Shenzhen LCS Compliance Testing Laboratory Ltd. FCC ID: 2ADIW-HL-6110H ________________________________________________________________________________ _________ This report shall not be reproduced except in full, without the written approval of Shenzhen LCS Compliance Testing Laboratory Ltd. Page 5 of 5 Fig. 9

Shenzhen LCS Compliance Testing Laboratory Ltd. FCC ID: 2ADIW-HL-6110H This report shall not be reproduced except in full, without the written approval of Shenzhen LCS Compliance Testing Laboratory Ltd. Page 1 of 1 Label and Location Size: L: 4.0cm*W: 2.0cm Label Location

Shenzhen LCS Compliance Testing Laboratory Ltd. FCC ID: 2ADIW-HL-6110H ________________________________________________________________________________ _________ This report shall not be reproduced except in full, without the written approval of Shenzhen LCS Compliance Testing Laboratory Ltd. Page 1 of 4 INTERIOR PHOTOGRAPHS Fig. 1 Fig. 2 Shenzhen LCS Compliance Testing Laboratory Ltd. FCC ID: 2ADIW-HL-6110H ________________________________________________________________________________ _________ This report shall not be reproduced except in full, without the written approval of Shenzhen LCS Compliance Testing Laboratory Ltd. Page 2 of 4 Fig. 3 Fig. 4 Shenzhen LCS Compliance Testing Laboratory Ltd. FCC ID: 2ADIW-HL-6110H ________________________________________________________________________________ _________ This report shall not be reproduced except in full, without the written approval of Shenzhen LCS Compliance Testing Laboratory Ltd. Page 3 of 4 Fig. 5 Fig. 6 Shenzhen LCS Compliance Testing Laboratory Ltd. FCC ID: 2ADIW-HL-6110H ________________________________________________________________________________ _________ This report shall not be reproduced except in full, without the written approval of Shenzhen LCS Compliance Testing Laboratory Ltd. Page 4 of 4 Fig. 7 Fig. 8 BT ANT

Shenzhen LCS Compliance Testing Laboratory Ltd. FCC ID: 2ADIW-HL-6110H ________________________________________________________________________ ___ This report shall not be reproduced except in full, without the written approval of Shenzhen LCS Compliance Testing Laboratory Ltd. Page 1 of 5 FCC RF Exposure Evaluation 1. Product Information FCC ID : 2ADIW-HL-6110H Product name : Massage chair Test Model : N-0003H Power supply : Input: AC110V, 60Hz Bluetooth : 2402MHz-2480MHz Channel Number : 79 Channels for Bluetooth V5.1(DSS) 40 channels for Bluetooth V5.1(DTS) Channel Spacing : 1MHz for Bluetooth V5.1(DSS) 2MHz for Bluetooth V5.1(DTS) Modulation Type : GFSK, π/4-DQPSK, 8-DPSK for Bluetooth V5.1(DSS) GFSK for Bluetooth V5.1 (DTS) Bluetooth Version : V5.1 Antenna Type : PCB Antenna, Antenna Gain : 1.2dBi(Max.) Hardware version : / Software version : / Exposure category : General population/uncontrolled environment EUT Type : Production Unit Device Type : Portable Device Shenzhen LCS Compliance Testing Laboratory Ltd. FCC ID: 2ADIW-HL-6110H ________________________________________________________________________ ___ This report shall not be reproduced except in full, without the written approval of Shenzhen LCS Compliance Testing Laboratory Ltd. Page 2 of 5 2. Evaluation method and Limit According to KDB447498 D01 General RF Exposure Guidance v06 Section 4.3.1 Standalone SAR test exclusion considerations: “Unless specifically required by the published RF exposure KDB procedures, standalone 1-g head or body and 10-g extremity SAR evaluation for general population exposure conditions, by measurement or numerical simulation, is not required when the corresponding SAR Test Exclusion Threshold condition, listed below, is satisfied. These test exclusion conditions are based on source-based time-averaged maximum conducted output power of the RF channel requiring evaluation, adjusted for tune-up tolerance, and the minimum test separation distance required for the exposure conditions.22 The minimum test separation distance is determined by the smallest distance from the antenna and radiating structures or outer surface of the device, according to the host form factor, exposure conditions and platform requirements, to any part of the body or extremity of a user or bystander (see 5) of section 4.1). To qualify for SAR test exclusion, the test separation distances applied must be fully explained and justified by the operating configurations and exposure conditions of the transmitter and applicable host platform requirements, typically in the SAR measurement or SAR analysis report, according to the required published RF exposure KDB procedures. When no other RF exposure testing or reporting is required, a statement of justification and compliance must be included in the equipment approval, in lieu of the SAR report, to qualify for the SAR test exclusion. When required, the device specific conditions described in the other published RF exposure KDB procedures must be satisfied before applying these SAR test exclusion provisions; for example, handheld PTT two-way radios, handsets, laptops & tablets etc.“ [(max. power of channel, including tune-up tolerance, mW)/ (min. test separation distance, mm)+ · *√f (GHz)+ ≤ 3.0 for 1-g SAR and ≤ 7.5 for 10-g extremity SAR, where: • f (GHz) is the RF channel transmit frequency in GHz • Power and distance are rounded to the nearest mW and mm before calculation • The result is rounded to one decimal place for comparison • 3.0 and 7.5 are referred to as the numeric thresholds in the step 2 below The test exclusions are applicable only when the minimum test separation distance is ≤ 50 mm and for transmission frequencies between 100 MHz and 6 GHz. When the minimum test separation distance is < 5 mm, a distance of 5 mm according to f) in section 4.1 is applied to determine SAR test exclusion. When one of the following test exclusion conditions is satisfied for all combinations of simultaneous transmission configurations, further equipment approval is not required to incorporate transmitter modules in host devices that operate in the mixed mobile and portable host platform exposure conditions. The grantee is responsible for documenting this according to Class I permissive change requirements. Antennas that qualify for standalone SAR test exclusion must apply the estimated standalone SAR to determine simultaneous transmission test exclusion. a) The [∑ of (the highest measured or estimated SAR for each standalone antenna configuration, adjusted for maximum tune-up tolerance) / 1.6 W/kg] + [∑ of MPE ratios] is ≤ 1.0. b)The SAR to peak location separation ratios of all simultaneously transmitting antenna pairs operating in portable device exposure conditions are all ≤ 0.04, and the [∑ of MPE ratios] is ≤ 1.0. 3. Refer Evaluation Method ANSI C95.1–1999: IEEE Standard for Safety Levels with Respect to Human Exposure to Radio Frequency Electromagnetic Fields, 3 kHz to 300 GHz. FCC KDB publication 447498 D01 General RF Exposure Guidance v06: Mobile and Portable Devices RF Exposure Procedures and Equipment Authorization Policies. FCC CFR 47 part1 1.1310: Radiofrequency radiation exposure limits. FCC CFR 47 part2 2.1093: Radiofrequency radiation exposure evaluation: portable devices Shenzhen LCS Compliance Testing Laboratory Ltd. FCC ID: 2ADIW-HL-6110H ________________________________________________________________________ ___ This report shall not be reproduced except in full, without the written approval of Shenzhen LCS Compliance Testing Laboratory Ltd. Page 3 of 5 4. Conducted Power Results [BT Max Conducted Power] Mode Channel Frequency (MHz) Peak Conducted Output Power (dBm) GFSK 0 2402 1.17 39 2441 2.34 78 2480 0.80 π/4DQPSK 0 2402 0.25 39 2441 1.42 78 2480 -0.09 8DPSK 0 2402 0.46 19 2440 1.61 39 2480 0.13 [BLE Max Conducted Power] Mode Channel Frequency (MHz) Peak Conducted Output Power (dBm) BT LE 0 2402 1.01 19 2440 2.14 39 2480 0.67 Shenzhen LCS Compliance Testing Labora…

Text truncated - open the document above for the full version.

Shenzhen LCS Compliance Testing Laboratory Ltd. FCC ID: 2ADIW-HL-6110H Report No.: LCS211012115AEA 1 / 43 Appendix A RF Test Data for BT (Conducted Measurement) Product Name: Massage chair Test Model: N-0003H Environmental Conditions Temperature: 23.5 C Relative Humidity: 52.2% ATM Pressure: 100.0 kPa Test Engineer: Wunder Wu Supervised by: Li Huan Shenzhen LCS Compliance Testing Laboratory Ltd. FCC ID: 2ADIW-HL-6110H Report No.: LCS211012115AEA 2 / 43 A.1 20dB Emission Bandwidth Test Result TestMode Antenna Channel 20db EBW[MHz] FL[MHz] FH[MHz] Limit[MHz] Verdict DH5 Ant1 2402 0.978 2401.529 2402.507 --- PASS 2441 1.011 2440.481 2441.492 --- PASS 2480 1.029 2479.463 2480.492 --- PASS 2DH5 Ant1 2402 1.323 2401.337 2402.660 --- PASS 2441 1.314 2440.343 2441.657 --- PASS 2480 1.323 2479.334 2480.657 --- PASS 3DH5 Ant1 2402 1.317 2401.343 2402.660 --- PASS 2441 1.320 2440.346 2441.666 --- PASS 2480 1.296 2479.352 2480.648 --- PASS Shenzhen LCS Compliance Testing Laboratory Ltd. FCC ID: 2ADIW-HL-6110H Report No.: LCS211012115AEA 3 / 43 Test Graphs DH5_Ant1_2402 DH5_Ant1_2441 DH5_Ant1_2480 Shenzhen LCS Compliance Testing Laboratory Ltd. FCC ID: 2ADIW-HL-6110H Report No.: LCS211012115AEA 4 / 43 2DH5_Ant1_2402 2DH5_Ant1_2441 Shenzhen LCS Compliance Testing Laboratory Ltd. FCC ID: 2ADIW-HL-6110H Report No.: LCS211012115AEA 5 / 43 2DH5_Ant1_2480 3DH5_Ant1_2402 3DH5_Ant1_2441 Shenzhen LCS Compliance Testing Laboratory Ltd. FCC ID: 2ADIW-HL-6110H Report No.: LCS211012115AEA 6 / 43 3DH5_Ant1_2480 Shenzhen LCS Compliance Testing Laboratory Ltd. FCC ID: 2ADIW-HL-6110H Report No.: LCS211012115AEA 7 / 43 A.2 Maximum conducted output power Test Result TestMode Antenna Channel Result[dBm] Limit[dBm] Verdict DH5 Ant1 2402 1.17 ≤20.97 PASS 2441 2.34 ≤20.97 PASS 2480 0.80 ≤20.97 PASS 2DH5 Ant1 2402 0.25 ≤20.97 PASS 2441 1.42 ≤20.97 PASS 2480 -0.09 ≤20.97 PASS 3DH5 Ant1 2402 0.46 ≤20.97 PASS 2441 1.61 ≤20.97 PASS 2480 0.13 ≤20.97 PASS Shenzhen LCS Compliance Testing Laboratory Ltd. FCC ID: 2ADIW-HL-6110H Report No.: LCS211012115AEA 8 / 43 Test Graphs DH5_Ant1_2402 DH5_Ant1_2441 DH5_Ant1_2480 Shenzhen LCS Compliance Testing Laboratory Ltd. FCC ID: 2ADIW-HL-6110H Report No.: LCS211012115AEA 9 / 43 2DH5_Ant1_2402 2DH5_Ant1_2441 Shenzhen LCS Compliance Testing Laboratory Ltd. FCC ID: 2ADIW-HL-6110H Report No.: LCS211012115AEA 10 / 43 2DH5_Ant1_2480 3DH5_Ant1_2402 3DH5_Ant1_2441 Shenzhen LCS Compliance Testing Laboratory Ltd. FCC ID: 2ADIW-HL-6110H Report No.: LCS211012115AEA 11 / 43 3DH5_Ant1_2480 Shenzhen LCS Compliance Testing Laboratory Ltd. FCC ID: 2ADIW-HL-6110H Report No.: LCS211012115AEA 12 / 43 A.3 Carrier frequency separation Test Result TestMode Antenna Channel Result[dBm] Limit[dBm] Verdict DH5 Ant1 Hop 0.968 ≥0.652 PASS 2DH5 Ant1 Hop 1.074 ≥0.716 PASS 3DH5 Ant1 Hop 0.994 ≥0.663 PASS Test Graphs DH5_Ant1_Hop 2DH5_Ant1_Hop 3DH5_Ant1_Hop Shenzhen LCS Compliance Testing Laboratory Ltd. FCC ID: 2ADIW-HL-6110H Report No.: LCS211012115AEA 13 / 43 Shenzhen LCS Compliance Testing Laboratory Ltd. FCC ID: 2ADIW-HL-6110H Report No.: LCS211012115AEA 14 / 43 A.4 Time of occupancy Test Result TestMode Antenna Channel BurstWidth [ms] TotalHops [Num] Result[s] Limit[s] Verdict DH5 Ant1 Hop 2.88 80 0.23 ≤0.4 PASS 2DH5 Ant1 Hop 2.88 90 0.26 ≤0.4 PASS 3DH5 Ant1 Hop 2.89 70 0.202 ≤0.4 PASS Test Graphs DH5_Ant1_Hop 2DH5_Ant1_Hop Shenzhen LCS Compliance Testing Laboratory Ltd. FCC ID: 2ADIW-HL-6110H Report No.: LCS211012115AEA 15 / 43 3DH5_Ant1_Hop Shenzhen LCS Compliance Testing Laboratory Ltd. FCC ID: 2ADIW-HL-6110H Report No.: LCS211012115AEA 16 / 43 Shenzhen LCS Compliance Testing Laboratory Ltd. FCC ID: 2ADIW-HL-6110H Report No.: LCS211012115AEA 17 / 43 A.5 Number of hopping channels Test Result TestMode Antenna Channel Result[Num] Limit[Num] Verdict DH5 Ant1 Hop 79 ≥15 PASS 2DH5 Ant1 Hop 79 ≥15 PASS 3DH5 Ant1 Hop 79 ≥15 PASS Test Graphs DH5_Ant1_Hop 2DH5_Ant1_Hop 3DH5_Ant1_Hop Shenzhen LCS Compliance Testing Laboratory Ltd. FCC ID: 2ADIW-HL-6110H Report No.: LCS211012115AEA 18 / 43 Shenzhen LCS Compliance Testing Laboratory Ltd. FCC ID: 2ADIW-HL-6110H Report No.: LCS211012115AEA 19 / 43 A.6 Band edge measurements Test Result TestMode Antenna ChName Channel RefLevel [dBm] Result [dBm] Limit [dBm] Verdict DH5 Ant1 Low 2402 0.56 -49.5 ≤-19.44 PASS High 2480 0.40 -47.53 ≤-19.6 PASS Low Hop_2402 0.93 -49.26 ≤-19.07 PASS High Hop_2480 0.56 -44.26 ≤-19.44 PASS 2DH5 Ant1 Low 2402 -0.63 -49.08 ≤-20.63 PASS High 2480 -1.00 -48.16 ≤-21 PASS Low Hop_2402 -3.84 -49.73 ≤-23.84 PASS High Hop_2480 -1.13 -48.44 ≤-21.13 PASS 3DH5 Ant1 Low 2402 -0.69 -49.88 ≤-20.69 PASS High 2480 -1.28 -48.45 ≤-21.28 PASS Low Hop_2402 -3.83 -49.7 ≤-23.83 PASS High Hop_2480 -2.64 -48.95 ≤-22.64 PASS Test Graphs DH5_Ant1_Low_2402 DH5_Ant1_High_2480 Shenzhen LCS Compliance Testing Laboratory Ltd. FCC ID: 2ADIW-HL-6110H Report No.: LCS211012115AEA 20 / 43 DH5_Ant1_Low_Hop_2402 DH5_Ant1_High_Hop_2480 Shenzhen LCS Compliance Testing Laboratory Ltd. FCC ID: 2ADIW-HL-6110H Report No.: LCS211012115AEA 21 / 43 2DH5_Ant1_Low_2402 2DH5_Ant1_High_2480 2DH5_Ant1_Low_Hop_2402 Shenzhen LCS Compliance Testing Laboratory Ltd. FCC ID: 2ADIW-HL-6110H Report No.: LCS211012115AEA 22 / 43 2DH5_Ant1_High_Hop_2480 3DH5_Ant1_Low_2402 Shenzhen LCS Compliance Testing Laboratory Ltd. FCC ID: 2ADIW-HL-6110H Report No.: LCS211012115AEA 23 / 43 3DH5_Ant1_High_2480 3DH5_Ant1_Low_Hop_2402 3DH5_Ant1_High_Hop_2480 Shenzhen LCS Compliance Testing Laboratory Ltd. FCC ID: 2ADIW-HL-6110H Report No.: LCS211012115AEA 24 / 43 Shenzhen LCS Compliance Testing Laboratory Ltd. FCC ID: 2ADIW-HL-6110H Report No.: LCS211012115AEA 25 / 43 A.7 Conducted Spurious Emission Test Result TestMode Antenna Channel FreqRange [MHz] RefLevel [dBm] Result [dBm] Limit [dBm] Verdict DH5 Ant1 2402 Reference 0.17 0.17 --- PASS 30~1000 0.17 -61.07 ≤-19.83 PASS 1000~26500 0.17 -47.88 ≤-19.83 PASS 2441 Reference 1.62 1.62 --- PASS 30~1000 1.62 -61.78 ≤-18.38 PASS 1000~26500 1.62 -47.29 ≤-18.38 PASS 2480 Reference 0.29 0.…

Text truncated - open the document above for the full version.

Shenzhen LCS Compliance Testing Laboratory Ltd. FCC ID: 2ADIW-HL-6110H Report No.: LCS211012115AEA This report shall not be reproduced except in full, without the written approval of Shenzhen LCS Compliance Testing Laboratory Ltd. Page 1 of 36 FCC TEST REPORT FOR Henglin Home Furnishings Co., Ltd. Massage chair Test Model: N-0003H Prepared for : Henglin Home Furnishings Co., Ltd. Address : No.378,380, Jiaxi Road, Dipu Street, Anji County, Huzhou, Zhejiang Prepared by : Shenzhen LCS Compliance Testing Laboratory Ltd. Address : 101, 201 Bldg A & 301 Bldg C, Juji Industrial Park Yabianxueziwei, Shajing Street, Baoan District, Shenzhen, 518000, China Tel : (+86)755-82591330 Fax : (+86)755-82591332 Web : www.LCS-cert.com Mail : [email protected] Date of receipt of test sample : October 15, 2021 Number of tested samples : 2 Sample No. ： 211012115A-1, 211012115A-2 Serial number : Prototype Date of Test : October 15, 2021 ~ October 25, 2021 Date of Report : October 26, 2021 Shenzhen LCS Compliance Testing Laboratory Ltd. FCC ID: 2ADIW-HL-6110H Report No.: LCS211012115AEA This report shall not be reproduced except in full, without the written approval of Shenzhen LCS Compliance Testing Laboratory Ltd. Page 2 of 36 FCC TEST REPORT FCC CFR 47 PART 15 C (15.247) Report Reference No. ....................... : LCS211012115AEA Date of Issue ......................................... : October 26, 2021 Testing Laboratory Name ................. : Shenzhen LCS Compliance Testing Laboratory Ltd. Address ................................................. : 101, 201 Bldg A & 301 Bldg C, Juji Industrial Park Yabianxueziwei, Shajing Street, Baoan District, Shenzhen, 518000, China Testing Location/ Procedure ................ : Full application of Harmonised standards ■ Partial application of Harmonised standards □ Other standard testing method □ Applicant’s Name ............................... : Henglin Home Furnishings Co., Ltd. Address ................................................. : No.378,380, Jiaxi Road, Dipu Street, Anji County, Huzhou, Zhejiang Test Specification Standard................................................ : FCC CFR 47 PART 15 C (15.247) Test Report Form No............................ : LCSEMC-1.0 TRF Originator ..................................... : Shenzhen LCS Compliance Testing Laboratory Ltd. Master TRF .......................................... : Dated 2011-03 Shenzhen LCS Compliance Testing Laboratory Ltd. All rights reserved. This publication may be reproduced in whole or in part for non-commercial purposes as long as the Shenzhen LCS Compliance Testing Laboratory Ltd. is acknowledged as copyright owner and source of the material. Shenzhen LCS Compliance Testing Laboratory Ltd. takes no responsibility for and will not assume liability for damages resulting from the reader's interpretation of the reproduced material due to its placement and context. Test Item Description. ........................ : Massage chair Trade Mark ........................................... : NOUHAUS Test Model ........................................... : N-0003H Ratings.................................................. : Input: AC110V, 60Hz Result ................................................. : Positive Tested by: Compiled by: Approved by: Jack Liu/ Administrators Jin Wang/ Technique principal Gavin Liang / Manager Shenzhen LCS Compliance Testing Laboratory Ltd. FCC ID: 2ADIW-HL-6110H Report No.: LCS211012115AEA This report shall not be reproduced except in full, without the written approval of Shenzhen LCS Compliance Testing Laboratory Ltd. Page 3 of 36 FCC -- TEST REPORT Test Result Positive The test report merely corresponds to the test sample. It is not permitted to copy extracts of these test result without the written permission of the test laboratory. Test Report No. : LCS211012115AEA October 26, 2021 Date of issue Test Model.............................. : N-0003H EUT......................................... : Massage chair Applicant............................... : Henglin Home Furnishings Co., Ltd. Address................................... : No.378,380, Jiaxi Road, Dipu Street, Anji County, Huzhou, Zhejiang Telephone............................... : / Fax.......................................... : / Manufacturer......................... : Henglin Home Furnishings Co., Ltd. Address................................... : No.378,380, Jiaxi Road, Dipu Street, Anji County, Huzhou, Zhejiang Telephone............................... : / Fax.......................................... : / Factory................................... : Henglin Home Furnishings Co., Ltd. Address................................... : No.378,380, Jiaxi Road, Dipu Street, Anji County, Huzhou, Zhejiang Telephone............................... : / Fax.......................................... : / Shenzhen LCS Compliance Testing Laboratory Ltd. FCC ID: 2ADIW-HL-6110H Report No.: LCS211012115AEA This report shall not be reproduced except in full, without the written approval of Shenzhen LCS Compliance Testing Laboratory Ltd. Page 4 of 36 Revision History Revision Issue Date Revisions Revised By 000 October 26, 2021 Initial Issue Gavin Liang Shenzhen LCS Compliance Testing Laboratory Ltd. FCC ID: 2ADIW-HL-6110H Report No.: LCS211012115AEA This report shall not be reproduced except in full, without the written approval of Shenzhen LCS Compliance Testing Laboratory Ltd. Page 5 of 36 TABLE OF CONTENTS Description Page 1. GENERAL INFORMATION ..................................................................................................... 6 1.1 Description of Device (EUT) ................................................................................................................ 6 1.2 Support equipment List ......................................................................................................................... 7 1.3 External I/O Cable .........................................................................…

Text truncated - open the document above for the full version.

Shenzhen LCS Compliance Testing Laboratory Ltd. FCC ID: 2ADIW-HL-6110H ____________________________________________________…

Text truncated - open the document above for the full version.