2AEAN-STREAMERXProfessional audio interface and video capture card

REGULATORY AND SAFETY GUIDE Leitfaden für Sicherheit und Vorschriften 0927-0795-02-03 Important Safety Information 1. Read and understand the instructions and safety guide completely before using the product. 2. Ensure both the instruction manual and regulatory and safety guide are accessible to all users, including when passing the product on to third parties. 3. Only use this product with authorised RØDE accessories. 4. Do not open the product housing. This will void the warranty. 5. Refer all service and repair to RØDE- approved service personnel. Service or repair is required for products that have been damaged, exposed to liquid, rain or moisture, or do not operate normally. 6. Use the product only in the ways described in the instructions. 7. Do not use the product if it was damaged during transportation. 8. Keep the product away from liquids and electrically conductive objects that are not necessary for operation. 9. Do not use any solvents or corrosive cleaning agents to clean the product. 10. Do not adjust the controls of the product in an environment that requires your attention (operating machinery, driving etc.). Wichtige Sicherheitsinformationen 1. Die Anweisungen und der Sicherheitsleitfaden sind vor der Verwendung des Produkts vollständig zu lesen und zu beachten. 2. Stellen Sie sicher, dass sowohl die Betriebsanleitung als auch der Leitfaden für Vorschriften und Sicherheit für alle Benutzer zugänglich sind, auch bei Weitergabe des Produkts an Dritte. 3. Verwenden Sie dieses Produkt nur mit autorisiertem RØDE-Zubehör. 4. Öffnen Sie das Produktgehäuse nicht. Dadurch entfällt die Garantie. 5. Überlassen Sie alle Service- und Reparaturarbeiten von RØDE autorisiertem Servicepersonal. Bei Produkten, die beschädigt wurden; die Flüssigkeit, Regen oder Feuchtigkeit ausgesetzt waren; oder die nicht normal funktionieren, ist eine Wartung oder Reparatur erforderlich. 6. Verwenden Sie das Produkt nur auf die in der Anleitung beschriebene Weise. 7. Verwenden Sie das Produkt nicht, wenn es beim Transport beschädigt wurde. 8. Halten Sie das Produkt von Flüssigkeiten und elektrisch leitenden Gegenständen fern, die für den Betrieb nicht erforderlich sind. 9. Verwenden Sie zur Reinigung des Produkts keine Lösungsmittel oder ätzende Reinigungsmittel. 10. Nehmen Sie keine Einstellungen am Produkt vor, wenn Sie in einer Umgebung sind, die Ihre Aufmerksamkeit erfordert (Bedienung von Maschinen, Autofahren usw.). North America The STREAMER X must not be co-located or operated in conjunction with any other antenna or transmitter. The device complies with part 15 of the FCC rules. Operation is subject to the following two conditions: (1) This device may not cause harmful interference, and (2) This device must accept any interference received, including interference that may cause undesired operation. This equipment has been tested and found to comply with the limits for a Class B digital device, pursuant to part 15 of the FCC rules. These limits are designed to provide reasonable protection against harmful interference in a residential installation. This equipment generates, uses and can radiate radio frequency energy and, if not installed and used in accordance with the instructions, may cause harmful interference to radio communications. However, there is no guarantee that interference will not occur in a particular installation. If this equipment does cause harmful interference to radio or television reception, which can be determined by turning the equipment off and on, the user is encouraged to try to correct the interference by one or more of the following measures: 1. Reorient or relocate the receiving antenna. 2. Increase the separation between the equipment and the receiver. 3. Connect the equipment to an outlet on a circuit different from that to which the receiver is connected. 4. Consult the dealer or an experienced radio/TV technician for help. This equipment complies with FCC radiation exposure limits set forth in an uncontrolled environment. Changes or modifi cations not expressly approved by RØDE could void the user’s authority to operate the equipment. This device contains license-exempt transmitter(s)/receiver(s) that comply with Innovation, Science and Economic Development Canada’s license-exempt RSS(s). Operation is subject to the following two conditions: 1. This device may not cause interference. 2. This device must accept any interference, including interference that may cause undesired operation of the device. L’émetteur/récepteur exempt de licence contenu dans le présent appareil est conforme aux CNR d’Innovation, Sciences et Développement économique Canada applicables aux appareils radio exempts de licence. L’exploitation est autorisée aux deux conditions suivantes: (1) L’appareil ne doit pas produire de brouillage; (2) L’appareil doit accepter tout brouillage radioélectrique subi, même si le brouillage est susceptible d’en compromettre le fonctionnement. Radiation Exposure Statement: This equipment complies with FCC radiation exposure limits set forth for an uncontrolled environment. This equipment shall be installed and operated with a minimum distance of 20cm between the radiator & body. Radio Frequency Exposure Statement for Canada The device has been evaluated to meet general RF exposure requirements. The device can be used in mobile exposure conditions. The minimum separation distance is 20cm. Déclaration d’exposition aux radiofréquences pour IC L’appareil a été évalué pour répondre aux exigences générales en matière d’exposition aux RF. L’appareil peut être utilisé dans des conditions d’exposition mobiles. La distance de séparation minimale est de 20cm. 0927-0795-02-03 STREAMER X RSG.indd 10927-0795-02-03 STREAMER X RSG.indd 14/11/2022 8:59 am4/11/2022 8:59 am The crossed-out bin symbol on a product and/or packing indicates that this product should not be discarded with general domestic waste, but must be collected separately at the end of its service life.Please o…

Text truncated - open the document above for the full version.

Rode Microphones 107 Carnarvon Street, Silverwater 2128, Australia Agent Authorization Company: Rode Microphones Address: 107 Carnarvon Street, Silverwater 2128, Australia Product Name: Professional audio interface and video capture card Model Number(s): STREAMER X Product Description: Professional audio interface and video capture card We authorize MiCOM Labs Inc., 575 Boulder Court, Pleasanton, California 94566, USA, to act on our behalf on all matters concerning the certification of above named equipment. We declare that MiCOM Labs Inc. is allowed to forward all information related to the approval and certification of equipment to the regulatory agencies as required and to discuss any issues concerning the approval application. Any and all acts carried out by MiCOM Labs on our behalf shall have the same effect as acts of our own. Signature: Date: Apr. 17, 2023 Name: Pieter Schillbeeckx Title: Head of New Product Development Company: Rode Microphones

Report No.: AGC10232230315AP02 Page 1 of 3 EXTERNAL PHOTOS TOP VIEW OF EUT BOTTOM VIEW OF EUT Report No.: AGC10232230315AP02 Page 2 of 3 FRONT VIEW OF EUT BACK VIEW OF EUT Report No.: AGC10232230315AP02 Page 3 of 3 LEFT VIEW OF EUT RIGHT VIEW OF EUT ****************************************End of Report*************************************

4 1 DEC 2022 STREAMER X (0518) 0518-0905-01 BOTTOM LABEL 100% WHITE BASE MATERIAL: 100% BLACK CROP MARK (DO NOT PRINT) Designed & Manufactured in Australia 200% SCALE unit: mm ACTUAL SIZE 59.4 R4.7 44.4 20.1 HT0001967 6pt EXAMPLE: HT0001967~HT0001968 HT0001967 FCC ID: 2AEAN-STREAMERX Ø14.9 TO MATCH SERIAL NUMBER BELOW QR CODE Authorised UK Representative RØDE UK, Unit A, 23-25 Sunbeam Rd, London NW10 6JP, United Kingdom Authorised EU Representative RØDE EU, Neukirchner Str. 18, 65510 Hünstetten, Germany Designed & Manufactured in Australia FCC ID: 2AEAN-STREAMERX Authorised UK Representative RØDE UK, Unit A, 23-25 Sunbeam Rd, London NW10 6JP, United Kingdom Authorised EU Representative RØDE EU, Neukirchner Str. 18, 65510 Hünstetten, Germany The label is centered at the bottom of the product Model: Model:

Report No.: AGC10232230315AP02 Page 1 of 7 INTERNAL PHOTOS OPEN VIEW OF EUT (FIGURE 1) OPEN VIEW OF EUT (FIGURE 2) Report No.: AGC10232230315AP02 Page 2 of 7 ANTENNA CLOSE-UP PHOTO-1 ANTENNA CLOSE-UP PHOTO-2 2.4G antenna 1 2.4G antenna 2 Report No.: AGC10232230315AP02 Page 3 of 7 INTERNAL VIEW OF EUT (FIGURE 1) INTERNAL VIEW OF EUT (FIGURE 2) Report No.: AGC10232230315AP02 Page 4 of 7 INTERNAL VIEW OF EUT (FIGURE 3) INTERNAL VIEW OF EUT (FIGURE 4) Report No.: AGC10232230315AP02 Page 5 of 7 INTERNAL VIEW OF EUT (FIGURE 5) INTERNAL VIEW OF EUT (FIGURE 6) Report No.: AGC10232230315AP02 Page 6 of 7 INTERNAL VIEW OF EUT (FIGURE 7) INTERNAL VIEW OF EUT (FIGURE 8) Report No.: AGC10232230315AP02 Page 7 of 7 INTERNAL VIEW OF EUT (FIGURE 9) INTERNAL VIEW OF EUT (FIGURE 10) ****************************************End of Report*************************************

RF EXPOSURE EVALUATION 1. PRODUCT INFORMATION FCC ID 2AEAN-STREAMERX Product Description Professional audio interface and video capture card Model Name STREAMER X Frequency Band (Operating) WLAN: 2.412GHz ~ 2.462GHz WLAN: 5.18GHz ~ 5.32GHz / 5.50GHz ~ 5.70GHz WLAN: 5.745GHz ~ 5825GHz Bluetooth: 2.402GHz ~ 2.480GHz Others (2.4G: 2.402GHz ~ 2.480GHz) Device Category Portable (<20cm separation) Mobile (≥20cm separation) Others: Antenna Diversity Single antenna Multiple antennas Max. Output Power Antenna 1:-4.898dBm (Max) Antenna 2:3.623dBm (Max) Antenna Gain Antenna 1: -2.85dBi Antenna 2: -1.46dBi Minimum Assessment Distance 20cm Evaluation Applied MPE Evaluation SAR Evaluation Evaluation Result Pass 2. PORTABLE DEVICE EVALUATION METHOD AND LIMIT Following FCC KDB 447498 D01 “General SAR test exclusion guidance” The corresponding SAR Exclusion Threshold condition, listed below: 1) The 1-g and 10-g SAR test exclusion thresholds for 100 MHz to 6 GHz at test separation distances ≤50 mm are determined by: [(max. power of channel, including tune-up tolerance, mW)/(min. test separation distance, mm)] [if(GHz)] s 3.0 for 1-g SAR and ñ 7.5 for 10-g extremity SAR, where  f(GHz) is the RF channel transmit frequency in GHz.  Power and distance are rounded to the nearest mW and mm before calculation.  The result is rounded to one decimal place for comparison The test exclusions are applicable only when the minimum test separation distance is ≤50 mm and for transmission frequencies between 100 MHz and 6 GHz. When the minimum test separation distance is < 5 mm, a distance of 5 mm is applied to determine SAR test exclusion. 2) At 100 MHz to 6 GHz and for test separation distances > 50 mm, the SAR test exclusion threshold is determined according to the following: a) [Threshold at 50 mm in step 1) + (test separation distance - 50mm) ( f(MHz)/150)] mW, at 100MHz to 1500 MHz; b) [Threshold at 50 mm in step 1) + (test separation distance - 50 mm)-10] mW at > 1500 MHz and ≤6 GHz; 3) At frequencies below 100 MHz, the following may be considered for SAR test exclusion. a) The threshold at the corresponding test separation distance at 100 MHz in step 2) is multiplied by [1 + log(100/f(MHz))] for test separation distances > 50 mm and < 200 mm. b) The threshold determined by the equation in a) for 50 mm and 100 MHz is multiplied by 1/2 for test separation distances < 50 mm. c) SAR measurement procedures are not established below 100 MHz. When SAR test exclusion cannot be applied, a KDB inquiry is required to determine SAR evaluation requirements for any test results to be acceptable. 3. MOBILE DEVICE EVALUATION METHOD AND LIMIT Human exposure to RF emissions from mobile devices (47 CFR §2.1091) may be evaluated based on the MPE limits adopted by the FCC for electric and magnetic field strength and/or power density, as appropriate, since exposures are assumed to occur at distances of 20 cm or more from persons. LIMITS FOR GENERAL POPULATION / UNCONTROLLED EXPOSURE Frequency Range (MHz) E-field Strength (E) (V/m) Magnetic Field Strength (H) (A/m) Power Density (S) (mW/cm 2 ) Averaging Time |E| 2 , |H| 2 or S (Minutes) 0.3 -- 1.34 614 1.63 (100)* 30 1.34 -- 30 824/f 2.19/f (180/f 2 )* 30 30 -- 300 27.5 0.073 0.2 30 300 -- 1500 -- -- f/1500 30 1500 -- 100,000 -- -- 1.0 30 *Note: 1. f= Frequency in MHz * Plane-wave Equivalent Power Density 2. The averaging time for General Population/Uncontrolled exposure to fixed transmitters is not applicable for mobile and portable transmitters. See 47 CFR §§2.1091 and 2.1093 on source-based time-averaging requirement for mobile and portable transmitters. S=PG/4πR² Where: S=power density P=power input to antenna G=power gain of the antenna in the direction of interest relative to an isotropic radiator R=distance to the center of radiation of the antenna 4. MEASUREMENT RESULT A minimum test separation distance ≥ 20 cm is required between the antenna and radiating structures of the device and nearby persons to apply mobile device exposure limits. The distance must be at least 20 cm and fully supported by the operating and installation configurations of the transmitter and its antenna(s), according to the source-based time-averaged maximum power requirements of § 2.1091(d)(2). In cases where cable losses or other attenuations are applied to determine compliance, the most conservative operating configurations and exposure conditions must be evaluated. Antenna 1: Antenna Gain=-2.85dBi (Numeric 0.52), π=3.14 Antenna 2: Antenna Gain=-1.46dBi (Numeric 0.71), π=3.14 Note: 1. Only the worst case recorded. 2. The antenna 1 and antenna 2 cannot transmit simultaneously. 5. CONCLUSION Since Source-base time average power is below SAR test exclusion power thresholds, the SAR evaluation is not required. Test Mode Test Frequency (MHz) Max.Output Power (dBm) Max.Output Power (mW) Power Density (mW/cm 2 ) Measurement Limit (mW/cm 2 ) 2.4G(ANT 1) 2402 -4.898 0.3237 0.0000335 1 2.4G(ANT 2) 2402 3.623 2.3030 0.0003255 1

Page 1 of 61 FCC Test Report Report No.: AGC10232230315FE02 FCC ID : 2AEAN-STREAMERX APPLICATION PURPOSE : Original Equipment PRODUCT DESIGNATION : Professional audio interface and video capture card BRAND NAME : RØDE MODEL NAME : STREAMER X APPLICANT : Rode Microphones DATE OF ISSUE : Apr. 17, 2023 STANDARD(S) : FCC Part 15.247 REPORT VERSION : V1.0 Attestation of Global Compliance (Shenzhen) Co., Ltd Report No.: AGC10232230315FE02 Page 2 of 61 REPORT REVISE RECORD Report Version Revise Time Issued Date Valid Version Notes V1.0 / Apr. 17, 2023 Valid Initial Release Report No.: AGC10232230315FE02 Page 3 of 61 TABLE OF CONTENTS 1. VERIFICATION OF COMPLIANCE .................................................................................................................. 5 2. GENERAL INFORMATION .............................................................................................................................. 6 2.1. PRODUCT DESCRIPTION ........................................................................................................................ 6 2.2. TABLE OF CARRIER FREQUENCYS ....................................................................................................... 7 2.3. RELATED SUBMITTAL(S)/GRANT(S) ....................................................................................................... 8 2.4. TEST METHODOLOGY ............................................................................................................................. 8 2.5. SPECIAL ACCESSORIES .......................................................................................................................... 8 2.6. EQUIPMENT MODIFICATIONS ................................................................................................................. 8 2.7. ANTENNA REQUIREMENT ....................................................................................................................... 8 3. MEASUREMENT UNCERTAINTY ................................................................................................................... 9 4. DESCRIPTION OF TEST MODES ................................................................................................................. 10 5. SYSTEM TEST CONFIGURATION ................................................................................................................ 11 5.1. CONFIGURATION OF TESTED SYSTEM ............................................................................................... 11 5.2. EQUIPMENT USED IN TESTED SYSTEM .............................................................................................. 11 5.3. SUMMARY OF TEST RESULTS .............................................................................................................. 11 6. TEST FACILITY .............................................................................................................................................. 12 7. PEAK OUTPUT POWER ................................................................................................................................ 13 7.1. MEASUREMENT PROCEDURE .............................................................................................................. 13 7.2. TEST SET-UP (BLOCK DIAGRAM OF CONFIGURATION) .................................................................... 13 7.3. LIMITS AND MEASUREMENT RESULT .................................................................................................. 14 8. BANDWIDTH .................................................................................................................................................. 18 8.1. MEASUREMENT PROCEDURE .............................................................................................................. 18 8.2. TEST SET-UP (BLOCK DIAGRAM OF CONFIGURATION) .................................................................... 18 8.3. LIMITS AND MEASUREMENT RESULTS ............................................................................................... 18 9. CONDUCTED SPURIOUS EMISSION........................................................................................................... 25 9.1. MEASUREMENT PROCEDURE .............................................................................................................. 25 9.2. TEST SET-UP (BLOCK DIAGRAM OF CONFIGURATION) .................................................................... 25 9.3. MEASUREMENT EQUIPMENT USED .................................................................................................... 25 9.4. LIMITS AND MEASUREMENT RESULT .................................................................................................. 25 10. MAXIMUM CONDUCTED OUTPUT POWER SPECTRAL DENSITY ........................................................ 37 Report No.: AGC10232230315FE02 Page 4 of 61 10.1. MEASUREMENT PROCEDURE ............................................................................................................ 37 10.2. TEST SET-UP (BLOCK DIAGRAM OF CONFIGURATION) .................................................................. 37 10.3. MEASUREMENT EQUIPMENT USED .................................................................................................. 37 10.4. LIMITS AND MEASUREMENT RESULT................................................................................................ 37 11. RADIATED EMISSION ................................................................................................................................. 41 11.1. MEASUREMENT PROCEDURE ............................................................................................................ 41 11.2. TEST SETUP .......................................................................................................................................... 42 11.3. LIMITS AND MEASUREMENT RESULT...................................................................…

Text truncated - open the document above for the full version.

Antenna Report Specification Model STREAMER X Impedance 50Ω Test environment Free space Freq. Range 2.4-2.5GHz Antenna type Antenna 1: PCB Antenna Antenna 2: FPC Antenna VSWR 2.4-2.5GHz < 2.0 Gain Antenna 1: -2.85dBi(Peak gain) Antenna 2: -1.46dBi(Peak gain) Manufacturer RODE An tenna 1 (18*9mm) Antenna 2 (18*10mm) Antenna 2 Antenna 2 Antenna 1 Frequency(MHz) Efficiency(dB) Efficiency(%) Gain(dBi) 2400-10.1869.579-3.024 2410-10.3939.133-3.151 2420-10.5658.779-3.460 2430-10.0969.780-3.049 2440-10.2629.414-2.849 2450-10.7998.317-3.260 2460-10.5258.859-2.973 2470-10.8368.247-3.085 2480-10.9707.997-3.090 2490-11.2317.531-3.317 2500-11.4387.181-3.491 An tenna 2 Frequency(MHz) Efficiency(dB) Efficiency(%) Gain(dBi) 2400-8.81613.133-2.330 2410-8.82813.096-2.298 2420-9.02512.515-2.278 2430-8.63913.677-1.725 2440-8.44314.311-1.462 2450-8.72713.404-1.766 2460-8.60213.795-1.829 2470-8.71413.443-2.089 2480-8.58213.860-1.968 2490-8.46614.235-1.855 2500-8.47414.207-1.928 Antenna 1 2D POLAR RADIATION PATTERN FREQUENCY=2400MHZ FREQUENCY=2450MHZ FREQUENCY=2500MHZ Antenna 2 2D POLAR RADIATION PATTERN FREQUENCY=2400MHZ FREQUENCY=2450MHZ FREQUENCY=2500MHZ Antenna 1 3D RADIATION PATTERN FREQUENCY=2400MHZ FREQUENCY=2450MHZ FREQUENCY=2500MHZ Antenna 2 3D RADIATION PATTERN FREQUENCY=2400MHZ FREQUENCY=2450MHZ FREQUENCY=2500MHZ

Report No.: AGC10232230315AP01 Page 1 of 2 TEST SETUP PHOTOS RADIATED EMISSION TEST SETUP BELOW 1GHz RADIATED EMISSION TEST SETUP ABOVE 1GHz Report No.: AGC10232230315AP01 Page 2 of 2 AC POWER LINE CONDUCTED TEST SETUP RF CONDUCTED TEST SETUP ****************************************End of Report*************************************