2AECY-S-35Bluetooth Speaker

Bluetooth Speaker S‐35 User manual Turning on Turn the power switch to the ON position to turn on the player. Playing music If a memory card has been inserted when the player is turned on, it will enter the music mode automatically, play an alert tone, and then play the music stored on the memory card automatically. Press or and there will be appropriate alert tone. Press and hold or to adjust the volume. Press to pause / play music. Pairing mobile phone When turned on, the player will enter pairing mode automatically if there is no memory card inserted. You can also press the M key to enter the pairing mode if a memory card is inserted. The player will play an alert tone, and the red and blue background lights flash alternately, indicating that the player is searching for Bluetooth mobile phone for pairing. After connecting, it will play an alert tone (password: 0000). Connecting Bluetooth call When there is an incoming call, press the key directly to answer the call, or press and hold the key to hang up. When the call is connected, press and hold the or key to adjust the volume, and press the key again to end the call. Double tap the key to call the last dialed number directly. Mobile voice navigation and audio transmission function The voice prompt of mobile phone navigation can be increased via Bluetooth intercom. While playing music after the mobile phone is connected to the player via Bluetooth, press or to switch to the previous/next track, press and hold the or key to adjust the volume, and press the key to pause/play music. Low battery alert There will be voice prompt when the battery voltage is low. Turning off When the power switch is turned to OFF, the player cuts off all power, shuts down and doesn’t play alert tone. Product Parameters Output power: 3W Frequency response: 120~18KHz Impedance: 4Ω SNR ≥ 70dB Battery specification: 3.7V/800mAh Charging voltage: DC‐5V Dimensions: 76*76*63 mm Net weight: 183g Parts List Player*1 AUX audio*1 Micro data cable*1 Manual*1 Key Function Diagram ① Mode switch key ② Press to play previous track; press and hold to decrease volume ③ Press to play next track; press and hold to increase volume ④ Pause / play ⑤ Answer / end a call via Bluetooth ⑥ Microphone hole ⑦ Power switch ⑧ Charging port ⑨ TF card slot ⑩ AUX audio cable port FCC Caution: Any changes or modifications not expressly approved by the party responsible for compliance could void the user's authority to operate this equipment. This device complies with Part 15 of the FCC Rules. Operation is subject to the following two conditions: (1) This device may not cause harmful interference, and (2) this device must accept any interference received, including interference that may cause undesired operation. This device and its antenna(s) must not be co-located or operating in conjunction with any other antenna or transmitter. This equipment should be installed and operated with minimum distance 20cm between the radiator and your body. NOTE: This equipment has been tested and found to comply with the limits for a Class B digital device, pursuant to Part 15 of the FCC Rules. These limits are designed to provide reasonable protection against harmful interference in a residential installation. This equipment generates, uses and can radiate radio frequency energy and, if not installed and used in accordance with the instructions, may cause harmful interference to radio communications. However, there is no guarantee that interference will not occur in a particular installation. If this equipment does cause harmful interference to radio or television reception, which can be determined by turning the equipment off and on, the user is encouraged to try to correct the interference by one or more of the followingmeasures: -- Reorient or relocate the receiving antenna. -- Increase the separation between the equipment and receiver. -- Connect the equipment into an outlet on a circuit different from that to which the receiver is connected. -- Consult the dealer or an experienced radio/TV technician for help. FCC RF warning statement: the device has been evaluated to meet general RF exposure requirement , The device can be used in portable exposure condition without restriction.

SCS-F18: Project and Product Certification Representative Authorization Letter Page 1 of 2 Rev 5.0 775 Montague Expressway Milpitas, CA 95035 Tel: 408-526-1188 Fax: 408-526-1088 Email: [email protected] Project and Product Certification Representative Authorization Letter Reason for Amendment (current / obsolete) Revision History Approved Date From To Initial Release (obsolete) 1.0 1.0 Nov-14-2006 Revised wording (obsolete) 1.0 2.0 Sept–25-2007 Updated company template (obsolete) 2.0 3.0 Jan-31-2012 Updated letter information (obsolete) 3.0 4.0 May-23-2014 Added FCC ID field (current) 4.0 5.0 Sept 16 2014 SCS-F18: Project and Product Certification Representative Authorization Letter Page 2 of 2 Rev 5.0 SHENZHEN SOAIY TECHNOLOGY CO.,LTD. 2015/04/03 To: SIEMIC, INC. 775 Montague Expressway, Milpitas, CA 95035 USA Dear Sir/Madam, Re: Product Certification Representative Authorization Letter We, ___ SHENZHEN SOAIY TECHNOLOGY CO.,LTD._ _hereby authorize SIEMIC, Inc. to act as a Certification Body for certifying for the following project(s): Product： Bluetooth Speaker Trade Name： N/A Model Name： S-35 Serial Model： N/A FCC ID： 2AECY-S-35 Sincerely, Client’s name / title : Bruce Nan / Manager Contact information / address : 4F, Bldg. D, Fuxinlin Industrial Park, Hangcheng Industrial Zone, Xixiang Street, Bao'an District, Shenzhen, China

SCS-F19: Confidentiality Request Letter Page 1 of 2 Rev 4.0 775 Montague Expressway Milpitas, CA 95035 Tel: 408-526-1188 Fax: 408-526-1088 Email: [email protected] Confidentiality Request Letter Reason for Amendment (current / obsolete) Revision History Approved Date From To Initial Release (obsolete) 1.0 1.0 Nov-14-2006 Adding CFR 2.459 (obsolete) 1.0 2.0 August – 11 - 2008 Updated company template & Added text box (obsolete) 2.0 3.0 Jan-31-2012 Added IC confidentiality letter form (current) 3.0 4.0 March-26-2015 SCS-F19: Confidentiality Request Letter Page 2 of 2 Rev 4.0 SHENZHEN SOAIY TECHNOLOGY CO.,LTD. 2015/04/03 To: Federal Communications Commission Authorization and Evaluation Division 7435 Oakland Mills Road Columbia, MD Subject: Permanent Confidentiality Request for FCC ID: 2AECY-S-35 We hereby request confidential treatment of information accompanying this application as outlined below: - . Block Diagram - Schematics - Operational Description The above materials contain trade secrets and proprietary information not customarily released to the public. The public disclosure of these materials may be harmful to the applicant and provide unjustified benefits to its competitors. The applicant understands that pursuant to Section 0.457 & 0.459 of the Rules, disclosure of this application and all accompanying documentation will not be made before the date of the Grant for this application. Sincerely, Client’s name / title : Bruce Nan / Manager Contact information / address : 4F, Bldg. D, Fuxinlin Industrial Park, Hangcheng Industrial Zone, Xixiang Street, Bao'an District, Shenzhen, China

APPENDIX-PHOTOGRAPHS OF EUT CONSTRUCTIONAL DETAILS Photo 1 Photo 2 Photo 3 Photo 4 Photo 5 Photo 6

FCC ID LABELING AND LOCATION FCC ID Label Bluetooth Speaker Model NO.: S-35 FCC ID: 2AECY-S-35 FCC ID Label Location The label shown shall be permanently affixed at a conspicuous location on the device and be readily visible to the user at the time purchase (Labeling requirements per 2.925)

APPENDIX-PHOTOGRAPHS OF EUT CONSTRUCTIONAL DETAILS Photo 1 Photo 2 Photo 3 Photo 4 Photo 5 Photo 6 Photo 7 Photo 8 BT Anntena Photo 9

FCC ID : 2AECY-S-35 RF EXPOSURE EVALUATION METHOD FCC ID: 2AECY-S-35 SAR Test Exclusion Thresholds for 100 MHz – 6 GHz and ≤ 50 mm Approximate SAR Test Exclusion Power Thresholds at Selected Frequencies and Test Separation Distances are illustrated in the following Table. The 1-g and 10-g SAR test exclusion thresholds for 100 MHz to 6 GHz at test separation distances ≤ 50 mm are determined by: [(max. power of channel, including tune-up tolerance, mW)/(min. test separation distance, mm)] · [√f(GHz)] ≤ 3.0 for 1-g SAR and ≤ 7.5 for 10-g extremity SAR,where f(GHz) is the RF channel transmit frequency in GHz Power and distance are rounded to the nearest mW and mm before calculation The result is rounded to one decimal place for comparison The test exclusions are applicable only when the minimum test separation distance is ≤ 50 mm and for transmission frequencies between 100 MHz and 6 GHz. When the minimum test separation distance is < 5 mm, a distance of 5 mm is applied to determine SAR test exclusion. Maximum measured transmitter power. BT 1Mbps Test Channel Frequency (MHz) Peak Output Power (dBm) Peak Output Power (mW) CH00 2402 0.109 1.025 CH39 2441 0.228 1.054 CH78 2480 0.142 1.033 2Mbps CH00 2402 -0.361 0.920 CH39 2441 -0.207 0.953 CH78 2480 -0.294 0.935 Remark: The best case gain of the antenna is -1.0 dBi. -1.0 dBi logarithmic terms convert to numeric result is nearly 0.8 The 1-g and 10-g SAR test exclusion thresholds for 100 MHz to 6 GHz at test separation distances ≤ 50 mm are determined by: [(max. power of channel, including tune-up tolerance, mW)/(min. test separation distance,mm)] · [√f(GHz)] FCC ID : 2AECY-S-35 BT Te s t Channel Range tune up max power (dBm) [(max. power of channel, including tune-up tolerance, mW) (min. test separation distance,mm)] [f(GHz)] Result Limit 1Mbps CH00 0~2 2 1.585 5 2.402 0.491 3 CH39 0~2 2 1.585 5 2.441 0.495 3 CH78 0~2 2 1.585 5 2.480 0.499 3 2Mbps CH00 -1~1 1 1.259 5 2.402 0.390 3 CH39 -1~1 1 1.259 5 2.441 0.393 3 CH78 -1~1 1 1.259 5 2.480 0.397 3 The test Result is less than 3.0 for 1-g SAR and ≤ 7.5 for 10-g extremity SAR. Conclusion: No SAR is required. 

FCC RADIO TEST REPORT-BT FCC ID: 2AECY-S-35 Product： Bluetooth Speaker Trade Name： N/A Model Name： S-35 Serial Model： N/A Report No.： NTEK-2015NT02071224F Prepared for SHENZHEN SOAIY TECHNOLOGY CO.,LTD. 4F, Bldg. D, Fuxinlin Industrial Park, Hangcheng Industrial Zone, Xixiang Street, Bao'an District, Shenzhen, China Prepared by Shenzhen NTEK Testing Technology Co., Ltd. 1/F, Building E, Fenda Science Park, Sanwei Community,Xixiang Street Bao’an District, Shenzhen P.R. China Tel.: +86-0755-61156588 Fax.: +86-0755-61156599 Website:www.ntek.org.cn Page 2 of 59 Report No.:NTEK-2015NT02071224F TEST RESULT CERTIFICATION Applicant’s name ................. : SHENZHEN SOAIY TECHNOLOGY CO.,LTD. Address ................................. : 4F, Bldg. D, Fuxinlin Industrial Park, Hangcheng Industrial Zone, Xixiang Street, Bao'an District, Shenzhen, China Manufacture's Name ............ : SHENZHEN SOAIY TECHNOLOGY CO.,LTD. Address ................................. : 4F, Bldg. D, Fuxinlin Industrial Park, Hangcheng Industrial Zone, Xixiang Street, Bao'an District, Shenzhen, China Product description Product name ........................... : Bluetooth Speaker Model and/or type reference : S-35 Serial Model： N/A Standards ............................. : FCC Part15.247: 01 Oct. 2014 Test procedure .............................. ANSI C63.4-2009 This device described above has been tested by NTEK, and the test results show that the equipment under test (EUT) is in compliance with the FCC requirements. And it is applicable only to the tested sample identified in the report. This report shall not be reproduced except in full, without the written approval of NTEK, this document may be altered or revised by NTEK, personal only, and shall be noted in the revision of the document. Date of Test ............................................ : Date (s) of performance of tests ............. : 07 Feb. 2015 ~ 01 Apr. 2015 Date of Issue ........................................... : 01 Apr. 2015 Test Result ............................................... : Pass Testing Engineer : (Eileen Liu) Technical Manager : (Brown Lu) Authorized Signatory : (Bill Yao) Page 3 of 59 Report No.:NTEK-2015NT02071224F Table of Contents Page 1 . SUMMARY OF TEST RESULTS 5 1.1 TEST FACILITY 6 1.2 MEASUREMENT UNCERTAINTY 6 2 . GENERAL INFORMATION 7 2.1 GENERAL DESCRIPTION OF EUT 7 2.2 DESCRIPTION OF TEST MODES 9 2.3 TABLE OF PARAMETERS OF TEXT SOFTWARE SETTING 9 2.4 BLOCK DIGRAM SHOWING THE CONFIGURATION OF SYSTEM TESTED 10 2.5 DESCRIPTION OF SUPPORT UNITS(CONDUCTED MODE) 11 2.6 EQUIPMENTS LIST FOR ALL TEST ITEMS 12 3 . EMC EMISSION TEST 13 3.1 CONDUCTED EMISSION MEASUREMENT 13 3.1.1 POWER LINE CONDUCTED EMISSION LIMITS 13 3.1.2 TEST PROCEDURE 14 3.1.3 DEVIATION FROM TEST STANDARD 14 3.1.4 TEST SETUP 14 3.1.5 EUT OPERATING CONDITIONS 14 3.1.6 TEST RESULTS 15 3.2 RADIATED EMISSION MEASUREMENT 17 3.2.1 RADIATED EMISSION LIMITS 17 3.2.2 TEST PROCEDURE 18 3.2.3 DEVIATION FROM TEST STANDARD 18 3.2.4 TEST SETUP 19 3.2.5 EUT OPERATING CONDITIONS 20 3.2.6 TEST RESULTS (BELOW 30 MHZ) 21 3.2.7 TEST RESULTS (BETWEEN 30M – 1000 MHZ) 22 3.2.8 TEST RESULTS (ABOVE 1000 MHZ) 24 4 . NUMBER OF HOPPING CHANNEL 25 4.1 APPLIED PROCEDURES / LIMIT 25 4.1.1 TEST PROCEDURE 25 4.1.2 DEVIATION FROM STANDARD 25 4.1.3 TEST SETUP 25 4.1.4 EUT OPERATION CONDITIONS 25 4.1.5 TEST RESULTS 26 5 . AVERAGE TIME OF OCCUPANCY 27 5.1 APPLIED PROCEDURES / LIMIT 27 Page 4 of 59 Report No.:NTEK-2015NT02071224F Table of Contents Page 5.1.1 TEST PROCEDURE 27 5.1.2 DEVIATION FROM STANDARD 27 5.1.3 TEST SETUP 28 5.1.4 EUT OPERATION CONDITIONS 28 5.1.5 TEST RESULTS 29 6 . HOPPING CHANNEL SEPARATION MEASUREMENT 35 6.1 APPLIED PROCEDURES / LIMIT 35 6.1.1 TEST PROCEDURE 35 6.1.2 DEVIATION FROM STANDARD 35 6.1.3 TEST SETUP 35 6.1.4 EUT OPERATION CONDITIONS 35 6.1.5 TEST RESULTS 36 7 . BANDWIDTH TEST 40 7.1 APPLIED PROCEDURES / LIMIT 40 7.1.1 TEST PROCEDURE 40 7.1.2 DEVIATION FROM STANDARD 40 7.1.3 TEST SETUP 40 7.1.4 EUT OPERATION CONDITIONS 40 7.1.5 TEST RESULTS 41 8 . PEAK OUTPUT POWER TEST 45 8.1 APPLIED PROCEDURES / LIMIT 45 8.1.1 TEST PROCEDURE 45 8.1.2 DEVIATION FROM STANDARD 45 8.1.3 TEST SETUP 45 8.1.4 EUT OPERATION CONDITIONS 45 8.1.5 TEST RESULTS 46 9 . 100 KHZ BANDWIDTH OF FREQUENCY BAND EDGE 50 9.1 DEVIATION FROM STANDARD 50 9.2 TEST SETUP 50 9.3 EUT OPERATION CONDITIONS 50 9.4 TEST RESULTS 51 10 . ANTENNA REQUIREMENT 57 10.1 STANDARD REQUIREMENT 57 10.2 EUT ANTENNA 57 11 . EUT TEST PHOTO 58 APPENDIX-PHOTOGRAPHS OF EUT CONSTRUCTIONAL DETAILS Page 5 of 59 Report No.:NTEK-2015NT02071224F 1. SUMMARY OF TEST RESULTS Test procedures according to the technical standards: FCC Part15 (15.247) , Subpart C Standard Section Test Item Judgment Remark 15.207 Conducted Emission PASS 15.247(a)(1) Hopping Channel Separation PASS 15.247(b)(1) Peak Output Power PASS 15.247(c) Radiated Spurious Emission PASS 15.247(a)(iii) Number of Hopping Frequency PASS 15.247(a)(iii) Dwell Time PASS 15.247(a)(1) Bandwidth PASS 15.205 Band Edge Emission PASS 15.203 Antenna Requirement PASS NOTE: (1)” N/A” denotes test is not applicable in this Test Report Page 6 of 59 Report No.:NTEK-2015NT02071224F 1.1 TEST FACILITY NTEK Testing Technology Co., Ltd Add. : 1/F, Building E, Fenda Science Park, Sanwei Community, Xixiang Street, Bao’an District, Shenzhen P.R. China. FCC Registration No.:238937; IC Registration No.:9270A-1 CNAS Registration No.:L5516 1.2 MEASUREMENT UNCERTAINTY The reported uncertainty of measurement y ± U，where expended uncertainty U is based on a standard uncertainty multiplied by a coverage factor of k=2，providing a level of confidence of approximately 95 %。 No. Item Uncertainty 1 Conducted Emission Test ±1.38dB 2 RF power,conducted ±0.16dB 3 Spurious emissions,conducted ±0.21dB 4 All emissions,radiated(<1G) ±4.68dB 5 All emissions,radiated(>1G) ±4.89dB 6 Temperature ±0.5°C 7 Humidity ±2% Page 7 of 59 Report No.:NTEK-2015NT02071224F 2. GENERAL INFORMATION 2.1 GENERAL DESCRIPTION OF EUT Equipment Blue…

Text truncated - open the document above for the full version.

Page 58 of 59 Report No.:NTEK-2015NT02071224F 11. EUT TEST PHOTO Radiated Measurement Photos Page 59 of 59 Report No.:NTEK-2015NT02071224F CONDUCTED EMISSION Photos