2AEDZCY3XXXPPWIRDEPrimePro 15W Wireless Charger

PRIMEPRO 15W WIRELESS CHARGER USER MANUAL C FCC ID : 2AEDZCY3XXXPPWIRDE This device complies with Part 15 of the FCC Rules. Operation is subject to the following two conditions: (1) this device may not cause harmful interference, and (2) this device must accept any interference received, including interference that may cause undesired operation. “FCC RF Radiation Exposure Statement Caution: To maintain compliance with the FCC’s RF exposure guidelines, place the product at least 20cm from nearby persons.” ygnett and the Cygnett logo are trademarks of Cygnett Pty Ltd. Other brands and product names are trademarks or register ed trademarks of their respective holders. © 2020 Cygnett PTY LTD. 858 Lorimer Street, Por t Melbourne Victoria, 3207, Australia Australian Consumer Law Our goods come with guarantees that cannot be excluded under the Australian Consumer Law. Y ou are entitled to a replacement or refund for a major failure and compensation for any other reasonably for eseeable loss or damage. Y ou are also entitled to have the goods repaired or replaced if the goods fail to be of acceptable quality and the failure does not amount to a major failure. Cygnett warrants this product against defects in workmanship and material for a period of two (2) year s fr om its original purchase date. Y ou must present your receipt as proof of date of purchase for warranty validation. Please read the following information carefully and ret ain this for any warranty claim. Terms & Conditions • This product is for household use only. If the product is used in a commercial environment, the warranty period will be automatically reduced to three (3) months. • Cygnett warrants that, with normal use or service, the pr oduct will be free from faulty parts, manufacture or workmanship. • The warranty does not apply where damage is caused by other factor s, e.g. mishandling, abuse, accident or failure to follow operating instructions. This symbol on the product indicates that this product shall not be treat ed as household waste. Instead it shall be sent to the applicable collection point for the recycling of electronic equipment. By ensuring this product is disposed of correctly, y ou will help prevent potential negative consequences for the environment and human health. For more information about the recycling of this Caution 1. 2. Do not expose to extreme weather conditions. 3. Do not place close to a magnetic strip or strip card as it could cause magnetic failure. 4. Please keep charger a safe distance of at least 80cm from any implantable medical devices to avoid medical device interference. 5. This is not a toy and should be kept away from children. 6. In the case of the device overheating, please disconnect immediately. approved by the party responsible for compliance could void the user’s authority to operate the equipment. Cygnett takes no responsibility for damages caused by incorrect use of its products. Made in China. Warning: Changes or modifications to this unit not expressly approved by the party responsible for compliance could void the user’s authority to operate the equipment. NOTE: This equipment has been tested and found to comply with the limits for a Class B digital device, pursuant to Part 15 of the FCC Rules. These limits are designed to provide reasonable protection against harmful interference in a residential installation. This equipment generates, uses and can radiate radio frequency energy and, if not installed and used in accordance with the instructions, may cause harmful interference to radio communications. However, there is no guarantee that interference will not occur in a particular installation. If this equipment does cause harmful interference to radio or television reception, which can be determined by turning the equipment o and on, the user is encouraged to try to correct the interference by one or more of the following measures: 1. Reorient or relocate the receiving antenna. 2. Increase the separation between the equipment and receiver. 3. Connect the equipment into an outlet on a circuit dierent from that to which the receiver is connected. 4. Consult the dealer or an experienced radio/TV technician for help. This device complies with Part 15 of the FCC Rules. Operation is subject to the following two conditions: (1) this device may not cause harmful interference, and (2) this device must accept any interference received, including interference that may cause undesired operation. Installation Instructions 1. To begin using your PrimePro wireless charger, you will need to connect the 2. Place your wireless charging device on the wireless charging output (B), making sure it is aligned to the centre of the wireless charging output (B). 3. Your device should begin to wirelessly charge. Adjusting Height To ensure optimal charging speed, unscrew the tightening screw (E), then adjust the wireless charging pad, so that your device is aligned to the centre of the wireless charging output (B). Flat Lay Wir eless Charging Do this by unscrew the tightening screw (E) and removing the wireless charging pad from the stand. Troubleshooting For optimum charge speed, adjust your device so that it is aligned to the centre of the wireless charging output (B). Please ensure that the case on your performance. Some cases interfere with wireless charging if they contain metallic material or are overly thick Name PrimePro 15W Wir eless Charger – US Item Number CY3435WIRDE CY3436WIRDE CY3437WIRDE CY3438WIRDE Input 5V⎓3A (15W) 9V⎓2A (18W) 12V⎓1.67A (20W) Wir eless Output 5W 7.5W 10W 15W Total Output 15W Max A DC Power Adaptor B Wir eless Charging Output C Metal Stand D Phone Support E Tightening Screw A B C D E

Black - US() PrimePro 431 C I n p u t : 5 V ⎓ 3 A , 9 V ⎓ 2 A , 1 2 V ⎓ 1 . 6 7 A ( 2 0 W M a x ) W i r e l e s s O u t p u t : 5 W / 7 . 5 W / 1 0 W / 1 5 W ( 1 5 W M a x ) P r i m e P r o 1 5 W W i r e l e s s C h a r g e r I t e m n o : C Y 3 4 3 5 W I R D E I n p u t : 5 V ⎓ 3 A , 9 V ⎓ 2 A , 1 2 V ⎓ 1 . 6 7 A ( 2 0 W M a x ) W i r e l e s s O u t p u t : 5 W / 7 . 5 W / 1 0 W / 1 5 W ( 1 5 W M a x ) P r i m e P r o 1 5 W W i r e l e s s C h a r g e r I t e m n o : C Y 3 4 3 5 W I R D E ROHS F C C I D : 2 A E D Z C Y 3 X X X P P W I R D E 15 mm 3 mm 51 mm 15 mm 3 mm

Cygnett Pty Ltd TEST REPORT SCOPE OF WORK SAR Assessment– CY3435WIRDE, CY3436WIRDE, CY3437WIRDE, CY3438WIRDE REPORT NUMBER 201113044SZN-002 ISSUE DATE [REVISED DATE] 16 December 2020 [--------------------] PAGES 6 DOCUMENT CONTROL NUMBER RF Exposure © 2017 INTERTEK TEST REPORT Intertek No.: 201113044SZN-002 This report is for the exclusive use of Intertek's Client and is provided pursuant to the agreement between Intertek and its Client. Intertek's responsibility and liability are limited to the terms and conditions of the agreement. Intertek assumes no liability to any party, other than to the Client in accordance with the agreement, for any loss, expense or damage occasioned by the use of this report. Only the Client is authorized to permit copying or distribution of this report and then only in its entirety. Any use of the Intertek name or one of its marks for the sale or advertisement of the tested material, product or service must first be approved in writing by Intertek. The observations and test results in this report are relevant only to the sample tested. This report by itself does not imply that the material, product, or service is or has ever been under an Intertek certification program. Intertek Testing Services Shenzhen Ltd. Longhua Branch 101, 201, Building B, No. 308 Wuhe Avenue, Zhangkengjing Community, GuanHu Subdistrict, LongHua District, ShenZhen. Tel: (86 755) 8601 6288 Fax: (86 755) 8601 6751 Version: 01-November-2017 Page 1 of 6 RF Exposure 101, 201, Building B, No. 308 Wuhe Avenue, Zhangkengjing Community, GuanHu Subdistrict, LongHua District, ShenZhen. Tel: (86 755) 8601 6288 Fax: (86 755) 8601 6751 www.intertek.com Test Report Applicant : Cygnett Pty Ltd Level 1, 858 Lorimer Street, Port Melbourne VIC 3207 Australia Sample Description Product : PrimePro 15W Wireless Charger Model No. : CY3435WIRDE, CY3436WIRDE, CY3437WIRDE, CY3438WIRDE Brand Name : Cygnett Electrical Rating : Input: 5V/3A, 9V/2A, 12V/1.67A (20W Max), Wireless Output: 5W/7.5W/10W/15W (15W Max) Adaptor : Input: 100-240~ 50/60Hz, 0.6A Output: 5.0V/3.0A (15.0W), 9.0V/2.0A (18.0W), 12.0V/1.67A (20.0W Max) Date Received : 13 November 2020 Date Test Conducted : 13 November 2020 to 11 December 2020 Test Requested : Test for compliance with CFR 47 part 1 Test Method : Environmental evaluation and exposure limit according to FCC CFR 47 part 1, 1.1307(c) and (d), 1.1310 Test Result : Pass Conclusion : When determining of test conclusion, measurement uncertainty of tests have been considered. ******************************** End of Page ******************************** Prepared and Checked By: Approved By: Jeff Liang Kidd Yang Engineer Technical Supervisor Date: 16 December 2020 TEST REPORT Intertek No.: 201113044SZN-002 Version: 01-November-2017 Page 2 of 6 RF Exposure Test Report Test Setup Configuration Note - The RF exposure test is performed in the shield room. - The test distance is between the edge of the charger and the geometric centre of probe. - The Model: CY3436WIRDE, CY3437WIRDE, CY3438WIRDE is the same as the Model: CY3435WIRDE in hardware aspect. The difference in model number serves as marketing strategy. Test Equipment List Name of instrument Model Manufacturer Cal. Date Due Date Electric and Magnetic Field Analyzer EHP-50F Narda 2020-07-28 2021-07-28 TEST REPORT Intertek No.: 201113044SZN-002 Version: 01-November-2017 Page 3 of 6 RF Exposure Reference Limit: Environmental evaluation and exposure limit according to FCC CFR 47 part 1, 1.1307(c) and (d), 1.1310 According to FCC 1.1310: The criteria listed in the following table shall be used to evaluate the environment impact of human exposure to radio frequency (RF) radiation. LIMITS FOR MAXIMUM PERMISSIBLE EXPOSURE (MPE) Frequency Range ( MHz ) Electric Field strength (V/m) Magnetic Field Strength (A/m) Power Density (mW/cm 2 ) Average Time (minutes) (A) Limits for Occupational/Controlled Exposure 0.3 – 3.0 614 1.63 (100) * 6 (B) Limits for General Population/Uncontrolled Exposure 0.3 – 1.34 614 1.63 (100) * 30 Note: * = Plane wave equivalent power density Test Result: H-Field Strength at 15 cm surrounding the EUT and 20cm above the top surface of the EUT Frequency Range (MHz) EUT Operation mode Probe Position Front (A/m) Probe Position Rear (A/m) Probe Position Left (A/m) Probe Position Right (A/m) Probe Position Top (A/m) Limits (A/m) 0.110- 0.205 1% Battery Level 0.1902 0.1764 0.0472 0.0475 0.0478 1.63 0.110- 0.205 50% Battery Level 0.2724 0.3093 0.0873 0.0814 0.0673 1.63 0.110- 0.205 99% Battery Level 0.6337 0.4497 0.1656 0.1176 0.1267 1.63 0.110- 0.205 Stand-by 0.0433 0.0442 0.0448 0.0436 0.0433 1.63 E-Field Strength at 15 cm surrounding the EUT and 20cm above the top surface of the EUT Frequency Range (MHz) EUT Operation mode Probe Position Front (V/m) Probe Position Rear (V/m) Probe Position Left (V/m) Probe Position Right (V/m) Probe Position Top (V/m) Limits (V/m) 0.110- 0.205 1% Battery Level 0.9479 0.4519 0.5308 0.6596 0.5447 614 0.110- 0.205 50% Battery Level 0.8715 0.4977 0.5561 0.7821 0.7061 614 0.110- 0.205 99% Battery Level 1.3445 0.6225 0.7446 1.0891 0.7668 614 0.110- 0.205 Stand-by 0.5254 0.5306 0.5254 0.5254 0.5248 614 TEST REPORT Intertek No.: 201113044SZN-002 Version: 01-November-2017 Page 4 of 6 RF Exposure Configuration photo of the test: H-Field & E-Field Strength test photos Front Rear TEST REPORT Intertek No.: 201113044SZN-002 Version: 01-November-2017 Page 5 of 6 RF Exposure Left Right TEST REPORT Intertek No.: 201113044SZN-002 Version: 01-November-2017 Page 6 of 6 RF Exposure Top ****************************** End of Report******************************

Cygnett Pty Ltd TEST REPORT SCOPE OF WORK FCC TESTING – CY3435WIRDE, CY3436WIRDE, CY3437WIRDE, CY3438WIRDE REPORT NUMBER 201113044SZN-001 ISSUE DATE [REVISED DATE] 16 December 2020 [--------------------] PAGES 19 DOCUMENT CONTROL NUMBER FCC ID 209_b © 2017 INTERTEK Test Report This report is for the exclusive use of Intertek's Client and is provided pursuant to the agreement between Intertek and its Client. Intertek's responsibility and liability are limited to the terms and conditions of the agreement. Intertek assumes no liability to any party, other than to the Client in accordance with the agreement, for any loss, expense or damage occasioned by the use of this report. Only the Client is authorized to permit copying or distribution of this report and then only in its entirety. Any use of the Intertek name or one of its marks for the sale or advertisement of the tested material, product or service must first be approved in writing by Intertek. The observations and test results in this report are relevant only to the sample tested. This report by itself does not imply that the material, product, or service is or has ever been under an Intertek certification program. Intertek Testing Services Shenzhen Ltd. Longhua Branch 101, 201, Building B, No. 308 Wuhe Avenue, Zhangkengjing Community, GuanHu Subdistrict, LongHua District, ShenZhen. Tel: (86 755) 8601 6288 Fax: (86 755) 8601 6751 Version: 01-November-2017 Page: 1 of 19 FCC ID 209_b 101, 201, Building B, No. 308 Wuhe Avenue, Zhangkengjing Community, GuanHu Subdistrict, LongHua District, ShenZhen. Tel: (86 755) 8601 6288 Fax: (86 755) 8601 6751 www.intertek.com Cygnett Pty Ltd Application For Certification FCC ID: 2AEDZCY3XXXPPWIRDE PrimePro 15W Wireless Charger Model: CY3435WIRDE, CY3436WIRDE, CY3437WIRDE, CY3438WIRDE Brand name: Cygnett Transmitter Report No.: 201113044SZN-001 We hereby certify that the sample of the above item is considered to comply with the requirements of FCC Part 15, Subpart C for Intentional Radiator, mention 47 CFR [10-1-19] Prepared and Checked by: Approved by: Jeff Liang Kidd Yang Engineer Technical Supervisor Date: 16 December 2020 Test Report Intertek Report No.: 201113044SZN-001 Version: 01-November-2017 Page: 2 of 19 FCC ID 209_b MEASUREMENT/TECHNICAL REPORT This report concerns (check one) Original Grant X Class II Change Equipment Type: DCD - Part 15 Low Power Transmitter Below 1705 kHz Deferred grant requested per 47 CFR 0.457(d)(1)(ii)? Yes No X If yes, defer until: date Company Name agrees to notify the Commission by: date of the intended date of announcement of the product so that the grant can be issued on that date. Transition Rules Request per 15.37? Yes No X If no, assumed Part 15, Subpart C for intentional radiator - the new 47 CFR [10-01-19] Edition] provision. Report prepared by: Jeff Liang Intertek Testing Services Shenzhen Ltd. Longhua Branch 101, 201, Building B, No. 308 Wuhe Avenue, Zhangkengjing Community, GuanHu Subdistrict, LongHua District, ShenZhen. Tel: (86 755) 8614 0743 Fax: (86 755) 8601 6751 Test Report Intertek Report No.: 201113044SZN-001 Version: 01-November-2017 Page: 3 of 19 FCC ID 209_b Table of Contents 1.0 Summary of Test Results ..................................................................................... 4 2.0 General Description .............................................................................................. 5 2.1 Product Description .............................................................................................. 5 2.2 Related Submittal(s) Grants ................................................................................. 5 2.3 Test Methodology ................................................................................................ 5 2.4 Test Facility ......................................................................................................... 5 3.0 System Test Configuration ................................................................................... 6 3.1 Justification ......................................................................................................... 6 3.2 EUT Exercising Software ..................................................................................... 6 3.3 Special Accessories ............................................................................................. 6 3.4 Equipment Modification ........................................................................................ 6 3.5 Measurement Uncertainty .................................................................................... 7 3.6 Support Equipment List and Description ............................................................. 7 4.0 Measurement Results ........................................................................................... 8 4.1 Field Strength Calculation .................................................................................... 8 4.2 Radiated Emission Configuration Photograph .................................................... 9 4.3 Radiated Spurious Emission ................................................................................ 9 4.4 Conducted Emission Configuration Photograph ................................................. 12 4.5 Conducted Emission.......................................................................................... 12 5.0 Equipment Photographs .................................................................................... 15 6.0 Product Labelling ................................................................................................ 15 7.0 Technical Specifications .................................................................................... 15 8.0 Instruction Manual .............................................................................................. 15 9.0 Miscellaneous Information ................................................................................. 16 9.1 20dB Bandwidth ........…

Text truncated - open the document above for the full version.

Front View Back View

Front View Side View