2AEDZCY4474Go-Create Selfie Stick

1. The product is not a toy. Keep it away from children. 2. Do not disassemble or throw controller into fire or water. 3. Do not expose controller to extreme weather conditions. 4. Do not use the controller if you observe visible defects. 5. Do not short circuit the controller or store it in a receptacle where it may be short circuited by other metallic or conductive objects. 6. Do not operate the controller if it has been wet or otherwise damaged, to prevent against electric shock, explosion and/or injury. 7. Never attempt to dismantle the unit. 8. Children should be supervised to ensure that they do not play with the product. 9. Always disconnect the controller when not in charging. 10. Do not use if broken, damaged, or exposed to liquids. 11. Not to be used in extremely high ambient temperatures. 12. Do not use with damaged or faulty accessories. 13. Do not place near any sources of heat, open flame, or liquid. 14. Disposal the controller into fire or a hot oven, mechanically crushing or cutting of a battery, can result in an explosion. 15. Leaving the controller in an extremely high temperature can result in an explosion or the leakage of flammable liquid or gas. 16. The controller will generate heat when charging. Always charge in a well-ventilated area. Do not charge under pillows, blankets or on flammable surfaces. 1 7. Do not subject the controller to mechanical shock such as crushing, bending, puncturing, or shredding. Avoid dropping or placing heavy objects on the controller. Cygnett takes no responsibility for damages caused by incorrect use of its products. This device complies with part 15 of the FCC Rules. Operation is subject to the following two conditions: (1) This device may not cause harmful interference, and (2) this device must accept any interference received, including interference that may cause undesired operation. Warning: changes or modifications not expressly approved by the party responsible for compliance could void the user’s authority to operate the equipment. NOTE: This equipment has been tested and found to comply with the limits for a Class B digital device, pursuant to part 15 of the FCC Rules. These limits are designed to provide reasonable protection against harmful interference in a residential installation. This equipment generates, uses and can radiate radio frequency energy and, if not installed and used in accordance with the instructions, may cause harmful interference to radio communications. However, there is no guarantee that interference will not occur in a particular installation. If this equipment does cause harmful interference to radio or television reception, which can be determined by turning the equipment off and on, the user is encouraged to try to connect the interference by one or more of the following measures: • Reorient or relocate the receiving antenna. • Increase the separation between the equipment and receiver. • Connect the equipment into an outlet on a circuit different from that to which the receiver is connected. • Consult the dealer or an experienced radio/TV technician for help. This symbol on the product indicates that this product shall not be treated as household waste. Instead it shall be sent to the applicable collection point for the recycling of electronic equipment. By ensuring this product is disposed of correctly, you will help prevent potential negative consequences for the environment and human health. For more information about the recycling of this product, please contact your local city office. Cygnett and the Cygnett logo are trademarks of Cygnett Pty Ltd. Other brands and product names are trademarks or registered trademarks of their respective holders. Made in China. Cygnett Pty Ltd 858 Lorimer Street, Port Melbourne, Victoria, 3207, Australia Cygnett UK Limited 71-75 Shelton St, London, WC2H 9JQ Cygnett USA Inc 3838 W Carson St, Ste 220, Torrance, CA 90503 Cygnett EU Office 2, Goudstraat 65, 2718RD Zoetermeer, The Netherlands GO-CREATE SELFIE STICK USER MANUAL Caution WARNING: Cancer and Reproductive Harm – www.P65Warnings.ca.gov. 75mm 11mm D - BT CONTROLLER C - TRIPOD/HANDLE E - EXTENDABLE SHAFT F - ANGLE ADJUSTER SCREW/L OCK G - ROTATABLE/ADJUSTABLE SMARTPHONE CRADLE H - ¼” SCREW THREAD (F OR ADDITIONAL ACTION CAMERA & ACCESSORY MOUNTING) B - A - BUTTON/LED Applying your smartphone – (G), making sure that it is straight and inline with the handle section (C). With two hands, separat e the cradle section (G) to a point where you sitting centrally. Orientat e device into the portr ait or landscape positions as needed. Applying your Go-Pro – locate the ¼” screw thread at the top of the cr adle section (G). Thread slowly ono your Go-Pro device until secured. To tighten, use the adjuster located just below the thread section (G). Extending the selfie stick – With two hands, grip both section in each hand (C & G) and slowly pull them apart from one another to begin ext ending to a length that is suitable. T o close, simply rever se the pr ocess until closed. Pairing your device with the controller – Locate the BT controller on the accessory (D). Depress the shutter button for two (2) seconds to activat e second to indicate its pairing at this point. When located in device BT settings and selected the LED will remain solid to indicate a connection. Please note, t o remove the BT controller from the main body, y ou will have to slightly ext end the shaft t o allow enough clear ance. Turning controller on & off – Once paired with a device, press and hold the Please note, t o re-apply the BT controller into the main body, y ou will have to slightly ext end the shaft t o allow enough clear ance to replace it. Auto shut-down – A fter ten (10) minutes of no use, the BT controller will Caution: Only recharge the BT Controller via a 5Vdc USB port Installation Instructions Name Item Number CY4474UNSES CY4475COSBD Battery Capacity 65mAh/0.24Wh Input Micro USB Input: 5.0V/0.1A (0.5W) Working Frequency Band Max Outp…

Text truncated - open the document above for the full version.

Form: RFT-AMER-TCB-OP-19n Revision: 1 Page 1 of 1 Date: 1/25/2023 CYGNETT PTY LTD Attention: Application Examiner Re: Covered List, located at https://www.fcc.gov/supplychain/coveredlist and 47 CFR parts §2.903 and §2.911(d)(5)(ii) of the FCC rules Applicant: CYGNETT PTY LTD FCC ID: 2AEDZCY4474 To whom it may concern, CYGNETT PTY LTD (“Applicant”) certifies that the equipment for which authorization is sought is not “covered” equipment prohibited from receiving an equipment authorization pursuant to 47 CFR part §2.903 of the FCC rules and does not originate directly or indirectly from any company named on the covered list located in the link above or any subsidiary or affiliate thereof. Applicant further certifies that, as of the date of the filing of the application, the Applicant is not identified on the Covered List as an entity producing “covered” equipment and is not a subsidiary or affiliate of any such entity pursuant to 47 CFR part §1.50002 and required by 47 CFR part §2.911(d)(5)(ii) of the FCC rules. I HEREBY CERTIFY THAT I am authorized to make the representations above on behalf of the Applicant and agree to immediately notify Intertek if there is any change in the status identified above. ______________________________ Grace Duan Product Development Specialist CYGNETT PTY LTD 2023-02-08

CYGNETT PTY LTD November 15, 2022 Federal Communications Commission 445 12 th Street SW Washington, DC 20554 Subject: Limited Agency Agreement CYGNETT PTY LTD FCC ID: 2AEDZCY4474 To Whom It May Concern: We, CYGNETT PTY LTD, hereby authorized Intertek Testing Services to act as our Agent for the purpose of preparing application for FCC ID number (2AEDZCY4474) under all applicable parts of the FCC rules and regulations. The effective date of this limited agency agreement is 15 November 2022. The Limited Agency Agreement expires on 15 November 2023, unless sooner terminated or extended by written notice to Intertek Testing Services and the Federal Communications Commission. This is to advise that we are in full compliance with the Anti-Drug Abuse Act. The applicant is not subject to a denial of federal benefits pursuant to Section 5301 of the Anti-Drug Act of 1988, 21 U.S.C. 862, and no party to the application is subject to a denial of federal benefits pursuant to that section. If you have any questions or comments, please do not hesitate to contact me. Sincerely, Grace Duan Product Development Specialist CYGNETT PTY LTD

1(2) CYGNETT PTY LTD Attention: Certification reviewer RE: Request for Confidentiality FCC ID: 2AEDZCY4474 To Whom It May Concern: Permanent Confidentiality [Complete this section if permanent confidentiality is requested] Request to withhold permanently from public review certain portions of the application for equipment certification for the referenced FCC identifiers. This request for confidentiality is made pursuant to 47 CFR 0.457(d) and 0.459 of the FCC Rules. In particular, the following sections of the application are to be kept permanently confidential: [Select one or more of items below, as appropriate] Schematics Block Diagrams Operational Description Tune-up Procedure Parts List Internal Photos (see note) Users Manual (see note) Note 1: Internal Photos may be held confidential 1) if the circuit board or internal components are not accessible to users. For example, it is acceptable if the circuit board is enclosed in epoxy. 2) Also, it is acceptable if the device is not accessible to the public, for example, a device mounted on the top of a large tower (or in a fenced enclosure) such that it is only serviceable by professional designated technicians under a Non-Disclosure Agreement (NDA). All sales for these devices must be under a NDA restricting the disclosure of the propriety information, including internal photos. Users Manual may be held confidential only when the manual contains proprietary technical information intended for professional technicians obligated under a NDA. All sales and distribution of the user’s manual must be under a NDA that restricts the disclosure of the information. In the application cover letter requesting permanent confidentiality the following additional description and the NDA exhibit is required: 1. Describe in detail how internal photos and/or users manual information are controlled to prevent them from becoming public or disclosed to unauthorized persons. 2. Describe how public access is restricted for products serviceable by professional designated technicians. 3. A statement that all sales of the non-consumer device will be under a NDA to include third party sales and that the final user of the device is subject to the NDA. 4. Provide an example of the NDA between the grantee and a purchaser. The request for confidentiality must Note 2: For scanning receiver, the schematics, block diagrams, operational description, tune-up procedure, parts list and internal photos are always held permanently confidential. Short-term Confidentiality [Complete this section if short-term confidentiality is requested] Request to withhold from public review for a period of 180 days from the date of the Grant of Equipment Authorization and prior to marketing, certain portions of the application for equipment certification for the referenced FCC identifiers. This request for confidentiality is made pursuant to 47 CFR 0.457(d) and 0.459 of the FCC Rules. In particular, the following sections of the application are to be kept short-term confidential for a period above from the date of the grant [Select one or more of items below that are not selected in the list above, as appropriate] Schematics Block diagrams Operational Description Tune-up Procedure 2(2) Parts List Test Setup Photos External Photos Internal Photos Users Manual Rationale for request for confidentiality: We have invested considerable time and materials in research and development to produce the referenced product. Permanent confidentiality: Disclosure of the permanently confidential portions of this application to competitors would not only give them significant competitive advantages in developing similar products, but would also disclose successful implementation of unpublished, leading edge technology developed by us. Short-term confidentiality: Disclosure of the short-term confidential portions of this application during the period of importation and/or distribution would reveal key aspects of proprietary technology to competitors and diminish the value of our investment in research and development. If you have questions or need further information, please contact the undersigned. Sincerely, _________________ Grace Duan Product Development Specialist 15 November 2022

REMOTE (1:1) STICK (1:1) 4.3 mm 30 mm Cool Gray 8C 2.1 mm 15 mm Cool Gray 8C 33.1mm 14.3mm Made In China Cool Gray 8C Item No: CY4474UNSES Go-Create Selfie Stick 21mm 5.9mm Item No: CY4474UNSES Go-Create Selfie Stick Recharge remote via a 5V DC 1A USB power adapter only. Made In China FCC ID: 2AEDZCY4474 Item N o: C Y4 474UNSES Go-Create Selfie Stick Recharge remote via a 5V DC 1A USB power adapter only. Made In China FCC ID: 2AEDZCY4474 Item No: CY4474UNSES Go-Create Selfie Stick 13.5mm 5.6 mm 5.6 mm

antenna

INTERTEK TESTING SERVICES RF Exposure The equipment under test (EUT) is a Go-Create Selfie Stick with BT 3.0 BDR function operating in 2402-2480MHz. The EUT is powered by DC 3.7V with battery; For more detail information pls. refer to the user manual. Modulation Type: GFSK. Bluetooth Version: BT 3.0 BDR(single mode) Antenna Type: Integral antenna. Antenna Gain: 2.3dBi. The nominal conducted output power specified: -10.3dBm (+/-3dB). The nominal radiated output power (e.i.r.p) specified: -8dBm (+/- 3dB). According to the KDB 447498: The maximun peak radiated emission for the EUT is 87.4dBμV/m at 3m in the frequency 2402MHz The EIRP = [(FS*D) ^2 / 30] mW = -7.83dBm which is within the production variation. The minimum peak radiated emission for the EUT is 85.7dBμV/m at 3m in the frequency 2480MHz The EIRP = [(FS*D) ^2 / 30] mW = -9.53dBm which is within the production variation. The maximun conducted output power specified is -7.3dBm = 0.16mW The source- based time-averaging conducted output power = 0.16 * Duty factor mW (where Duty Factor≤1) = 0.16 mW 1-mW Test Exemption: Since the source-based time-averaging conducted output power is well below 1-mW Test Exemption, per 447498 and §1.1307(b)(3)(i)(A), the EUT is considered to comply with SAR requirement without testing and no evaluation is required. FCC ID: 2AEDZCY4474

CYGNETT PTY LTD TEST REPORT SCOPE OF WORK FCC TESTING–CY4474UNSES, CY4475COSBD REPORT NUMBER 221115052SZN-002 ISSUE DATE [REVISED DATE] 15 December 2022 [---------------------] PAGES 27 DOCUMENT CONTROL NUMBER FCC ID 249_C © 2017 INTERTEK Intertek Report No.: 221115052SZN-002 This report is for the exclusive use of Intertek's Client and is provided pursuant to the agreement between Intertek and its Client. Intertek's responsibility and liability are limited to the terms and conditions of the agreement. Intertek assumes no liability to any party, other than to the Client in accordance with the agreement, for any loss, expense or damage occasioned by the use of this report. Only the Client is authorized to permit copying or distribution of this report and then only in its entirety. Any use of the Intertek name or one of its marks for the sale or advertisement of the tested material, product or service must first be approved in writing by Intertek. The observations and test results in this report are relevant only to the sample tested. This report by itself does not imply that the material, product, or service is or has ever been under an Intertek certification program. Intertek Testing Services Shenzhen Ltd. Longhua Branch 101, 201, Building B, No. 308 Wuhe Avenue, Zhangkengjing Community, GuanHu Subdistrict, LongHua District, ShenZhen, P.R. China Tel: (86 755) 8601 6288 Fax: (86 755) 8601 6751 Version: 01-November-2017 Page: 1 of 27 FCC ID 249_C Test Report CYGNETT PTY LTD Application For Certification FCC ID: 2AEDZCY4474 Go-Create Selfie Stick Model: CY4474UNSES, CY4475COSBD Brand Name: CYGNETT 2.4GHz Transceiver Report No.: 221115052SZN-002 We hereby certify that the sample of the above item is considered to comply with the requirements of FCC Part 15, Subpart C for Intentional Radiator, mention 47 CFR [10-1-21] Prepared and Checked by: Approved by: Karot Huang Assistant Engineer Peter Kang Sr. Technical Supervisor Date: 15 December 2022 Intertek Report No.: 221115052SZN-002 Version: 01-November-2017 Page: 2 of 27 FCC ID 249_C Test Report MEASUREMENT/TECHNICAL REPORT This report concerns (check one:) Original Grant X Class II Change Equipment Type: DXX - Part 15 Low Power Communication Device Transmitter Deferred grant requested per 47 CFR 0.457(d)(1)(ii)? Yes No X If yes, defer until: date Company Name agrees to notify the Commission by: date of the intended date of announcement of the product so that the grant can be issued on that date. Transition Rules Request per 15.37? Yes No X If no, assumed Part 15, Subpart C for intentional radiator − the new 47 CFR [10-1-21 Edition] provision. Report prepared by: Karot Huang Intertek Testing Services Shenzhen Ltd. Longhua Branch 101, 201, Building B, No. 308 Wuhe Avenue, Zhangkengjing Community, GuanHu Subdistrict, LongHua District, ShenZhen, P.R. China Tel / Fax: 86-755-8614 0743/86-755-8601 6661 Intertek Report No.: 221115052SZN-002 Version: 01-November-2017 Page: 3 of 27 FCC ID 249_C Test Report Table of Contents 1.0 Summary of Test Result ................................................................................................. 4 2.0 General Description ...................................................................................................... 5 2.1 Product Description .................................................................................................... 5 2.2 Related Submittal(s) Grants ......................................................................................... 5 2.3 Test Methodology ...................................................................................................... 5 2.4 Test Facility ............................................................................................................... 5 3.0 System Test Configuration ............................................................................................. 6 3.1 Justification ............................................................................................................... 6 3.2 EUT Exercising Software .............................................................................................. 6 3.3 Special Accessories ..................................................................................................... 6 3.4 Equipment Modification .............................................................................................. 6 3.5 Measurement Uncertainty .......................................................................................... 7 3.6 Support Equipment List and Description ........................................................................ 7 4.0 Emission Results ........................................................................................................... 8 4.1 Radiated Test Results .................................................................................................. 8 4.1.1 Field Strength Calculation ......................................................................................... 8 4.1.2 Radiated Emission Configuration Photograph .............................................................. 9 4.1.3 Radiated Emissions .................................................................................................. 9 4.1.4 Transmitter Spurious Emissions ............................................................................... 12 4.2 Conducted Emission Configuration Photograph ............................................................ 16 4.2.1 Conducted Emission ............................................................................................... 16 5.0 Equipment Photographs .............................................................................................. 19 6.0 Product Labelling ........................................................................................................ 19 7.0 Technical Specifications ....................................................................................…

Text truncated - open the document above for the full version.

RADIATED EMISSION TEST SET-UP Front View (Below 1GHz) Back View (Below 1GHz) The EUT is placed at the center of turntable Front View (Above 1GHz) Back View (Above 1GHz) The EUT is placed at the center of turntable