2AEPJ-TR210CAR ALARM

TR210 2025-06-20 © Automotive Data Solutions Inc. 1/15 OWNER’S MANUAL THE ART OF START™ TERMS OF USE INSTALLER TERMS OF USE Automotive Data Solutions Inc. (“ADS”) products are strictly intended for installation by Certified Technicians who are employed by a registered business specialized in the installation of automotive aftermarket electronics products. Prior to beginning installation of an ADS product in a vehicle, it is the Certified Technician’s responsibility to review the most current Product Guide, Install Guide and vehicle-specific notes available in Weblink®. ADS is not responsible for any damages whatsoever, including but not limited to any consequential damages, incidental damages, damages for loss of time, loss of earnings, loss of profit, commercial loss, loss of economic opportunity and the like that may or may not have resulted from the use, misuse, improper installation or operation of its products. Purchasers sole contractual remedy is refund of the purchase price of the ADS product(s). ADS reserves itself the right to suspend any Weblink® account without notice and decline to offer technical support to non-Certified Technicians, non-compliant Certified Technicians or end users. END USER TERMS OF USE ADS products are designed to remote start vehicles from a distance. In order to ensure your iDatastart system meets all safety regulations and operates as intended by the manufacturer, please follow the usage recommendations below: • DO NOT use this product for any purpose other than its intended usage. • DO NOT remote start a vehicle in an indoor or enclosed area (i.e. garage). Exhaust fumes are extremely dangerous and can cause personal injury or death. Install carbon monoxide detectors in every living area that can be exposed to vehicle exhaust fumes. • DO NOT remote start a vehicle while it is being serviced. Follow the Valet Mode procedure as outlined in your Owner’s Manual. • DO NOT remote start a vehicle in gear. • DO NOT remote start a vehicle with the key in the ignition. • DO NOT remote start a vehicle left unattended with open windows, unlocked doors or open convertible top. • DO NOT allow children handle or operate long range remotes. • ALWAYS engage your emergency brake prior to exiting your vehicle. This may limit motion if the vehicle is accidentally started in gear. TR210 2025-06-20 © Automotive Data Solutions Inc. 2/15 • AVOID remote starting your vehicle while passengers or pets are on board. This may increase the risk of shifter being put in gear after vehicle has been remote started. • AVOID parking your vehicle on an inclined surface or an area surrounded by obstacles. For manual vehicles, ALWAYS ensure the Reservation Mode sequence, as outlined in your Owner’s Manual, is correctly engaged prior to the next remote start. • AVOID delaying the inspection of your iDatastart system in the event of malfunction. Immediately contact a Certified Technician to ensure that installation or defective equipment is properly addressed. REMOTE OVERVIEW Your iDatastart remote start system may include one or both long-range remotes listed below. Please take a moment to familiarize yourself with their general features. REMOTE MODELTR210 TechnologyFM 1-WAY Max. Range1/2 mile Buttons5 Transmit Confirmation (TX)Top LED Receive Confirmation (RX)— Batteries Required2 x CR2016 Avg. Battery Life24 months Warranty1 year TR210 2025-06-20 © Automotive Data Solutions Inc. 3/15 REMOTE COMMANDS & CONFIRMATIONS Thanks to their multiplexing technology, iDatastart remotes can pack over 30 functions using only 5 buttons. In order to get the most out of your remotes, please take a moment to get acquainted with the following functions below: NOTES: 1. All functions must be enabled by an Authorized Dealer during installation to be functional on remote 2. Non-highlighted icons = Press & release button 3. Highlighted (grey) icons = Press & hold button for 2.5 seconds 4. Coma (,) between icons = Press buttons one after the other 5. Plus (+) between icons = Press buttons together 6. Timeout between each button press = 3 seconds 7. Function* = Available in 2nd Car Mode LOCK AND ARM* COMMANDLock & Arm* BUTTON DESCRIPTION Secures your vehicle by locking the doors and arming the alarm. UNLOCK AND DISARM* COMMANDUnlock & Disarm BUTTON DESCRIPTION Accesses your vehicle by unlocking the doors and disarming the alarm. QUERY* COMMANDQuery* BUTTON DESCRIPTION Queries vehicle and vehicle battery voltage and interior temperature. TR210 2025-06-20 © Automotive Data Solutions Inc. 4/15 PANIC* COMMANDPanic* BUTTON DESCRIPTIONTriggers the panic siren. AUX 5* COMMANDAUX 5* BUTTON DESCRIPTIONTo be completed by Authorized Dealer if applicable TRUNK RELEASE COMMANDTrunk Release* BUTTON DESCRIPTIONReleases the trunk or hatch. ENGINE START/STOP* COMMANDEngine Start/Stop* BUTTON DESCRIPTIONStarts and stops the engine. AUX 1 COMMANDAUX 1 BUTTON DESCRIPTIONTo be completed by Authorized Dealer if applicable AUX 2 TR210 2025-06-20 © Automotive Data Solutions Inc. 5/15 COMMANDAUX 2 BUTTON DESCRIPTIONTo be completed by Authorized Dealer if applicable AUX 3 COMMANDAUX 3 BUTTON DESCRIPTIONTo be completed by Authorized Dealer if applicable AUX 4 COMMANDAUX 4 BUTTON DESCRIPTIONTo be completed by Authorized Dealer if applicable 2ND CAR MODE COMMAND2nd Car Mode BUTTON * DESCRIPTION Controls two iDatastart-equipped vehicles using one remote. Works with all functions marked with an asterisk (*). SILENT LOCK* COMMANDSilent Lock* BUTTON DESCRIPTIONDisables the vehicle’s horn and alarm siren. SILENT UNLOCK* TR210 2025-06-20 © Automotive Data Solutions Inc. 6/15 COMMANDSilent Unlock* BUTTON DESCRIPTIONDisables the vehicle’s horn and alarm siren. VALET MODE ON/OFF COMMANDValet Mode ON/OFF BUTTON DESCRIPTION Turns off remote start and security features when servicing your vehicle or valet parking. Keyless entry features remains functional. RUNTIME EXTEND COMMANDRuntime Extend BUTTON DESCRIPTION Seamlessly extends your engine runtime with…

Text truncated - open the document above for the full version.

Automotive Data Solutions Inc. Covered Equipment Certification Attestation Letter 12/23/2025 Federal Communications Commission Authorization and Evaluation Division 7435 Oakland Mills Road Columbia, MD 21046 USA ATTN.: Reviewing Engineer FCC ID: 2AEPJ-TR210 Automotive Data Solutions Inc. (“the applicant”) certifies that the equipment for which authorization is sought is not “covered” equipment prohibited from receiving an equipment authorization pursuant to section 2.903 of the FCC rules. Note: If the equipment for which the applicant seeks authorization is produced by any of the entities identified on the current Covered List, the applicant should include an explanation on why the equipment is not “covered” equipment. Automotive Data Solutions Inc. (“the applicant”) certifies that, as of the date of the filing of the application, the applicant is not identified on the Covered List as an entity producing “covered” equipment. Automotive Data Solutions Inc. (“the applicant”) certifies that the equipment for which authorization is sought does not include cybersecurity or anti-virus software produced or provided by Kaspersky Lab, Inc. or any of its successors and assignees, including equipment with integrated Kaspersky Lab, Inc. (or any of its successors and assignees) cybersecurity or anti-virus software pursuant to DA-24-886 and KDB 986446 D01 Covered Equipment Guidance section B(2a). Signed: Printed name: Thanh Liem Trinh Title: Company Name: Automotive Data Solutions Inc. Date: 12/23/2025

Automotive Data Solutions Inc. DATE:7/31/2025 Industry Canada Certification & Engineering Bureau 3701 Carling Avenue, Bldg. 94 P.O. Box 11490, Station “H” Ottawa, Ontario K2H 8S2 Canada Authority to Act asAgent On our behalf, I appoint SHENZHEN STS TEST SERVICES CO., LTD; 101, Building B, Zhuoke Science Park, No.190 Chongqing Road, ZhanChengShequ, Fuhai Sub-District, Bao'an District, Shenzhen, Guang Dong, China, to act as our agent in the preparation of this application for equipment certification. I certify that submitted documents properly describe the device or system for which equipment certification is sought. I also certify that each unit manufactured, imported or marketed, as defined in the Industry Canada Certification & Engineering Bureau regulations will have affixed to it a label identical to that submitted for approval with this application. Dated this 7/31/2025 By: Thanh Liem Trinh Signature Printed Title: On behalf of : Automotive Data Solutions Inc. Telephone: 5148072888

Automotive Data Solutions Inc. Date:7/31/2025 Federal Communications Commission Authorization & Evaluation Division 7345 Oakland Mills Road Columbia, Maryland 21046 RE: LETTER OF AGENT AUTHORIZATION To Whom It May Concern: We, the undersigned, hereby authorize Compliance Testing LLC to act on our behalf in all matters relating to application for equipment authorization, including the signing of all documents relating to these matters. We also hereby certify that no party to the application authorized hereunder is subject to the denial of benefits, including FCC benefits, pursuant to Section 5301 of the Anti-Drug Abuse Act of 1988, 21 U.S.C.853(a). Sincerely, Dated this: 2025-7-31 By: Thanh Liem Trinh Signature Printed Title: Product Development Director. On behalf of: Automotive Data Solutions Inc. Telephone: 5148072888

Automotive Data Solutions Inc. DATE :2025-7-31 Equipment Autorisation Division Federal Communications Commission 7435 Oakland Mills Road Columbia, MD 21046 FCC ID: 2AEPJ-TR210 Product Name: CAR ALARM Request for Confidentiality Pursuant to Sections 0.457 and 0.459 of the commissions rules, we hereby request that the following documents be held confidential:  Schematics  Block diagram  Operation description  Bom These materials contain trade secrets and proprietary information and are not customarily released to the public. The public disclosure of this information might be harmful to the company and provide unjustified benefits to our competitors. Dated this 2025-7-31 By: Thanh Liem Trinh Signature Printed Title: On behalf of : Automotive Data Solutions Inc. Telephone: 5148072888

FCC ID: 2AEPJ-TR210 Page 1 of 3 EUT External Photos FCC ID: 2AEPJ-TR210 Page 2 of 3 FCC ID: 2AEPJ-TR210 Page 3 of 3 ------End------

Label: Label location:

FCC ID: 2AEPJ-TR210 Page 1 of 5 EUT Internal Photos FCC ID: 2AEPJ-TR210 Page 2 of 5 FCC ID: 2AEPJ-TR210 Page 3 of 5 FCC ID: 2AEPJ-TR210 Page 4 of 5 FCC ID: 2AEPJ-TR210 Page 5 of 5 ------End------

The test results presented in this report relate only to the object tested. This report shall not be reproduced, except in full, without the written approval of the ShenZhen STS Test Services Co., Ltd. MPE Report Report No.:STS2512107H01 Issued for Automotive Data Solutions Inc. 8400 Bougainville Montreal Quebec Canada H4P 2G1 Product Name: CAR ALARM Brand Name: N/A Model Name: TR210 Series Model(s): N/A FCC ID: 2AEPJ-TR210 Test Standards: FCC 47CFR §2.1093 Page 2 of 8 Report No.: STS2512107H01 TEST REPORT Applicant’s Name ................. : Automotive Data Solutions Inc. Address ................................. : 8400 Bougainville Montreal Quebec Canada H4P 2G1 Manufacturer's Name ........... : DONGGUAN PORTMAN ELECTRONIC SCIENCE AND TECHNOLOGY Address ................................. : NO.10, LUYI 2 ROAD,TANGXIA TOWN, DONGGUAN CITY GUANGDONG Product Description Product Name ........................ : CAR ALARM Brand Name .......................... : N/A Model Name .......................... : TR210 Series Model(s) ...................... : N/A Test Standards ..................... : FCC 47CFR §2.1093 447498 D01 Interim General RF Exposure Guidance v06 The test results presented in this report relate only to the object tested. This report shall not be reproduced, except in full, without the written approval of the ShenZhen STS Test Services Co., Ltd. Date of Test ........................................... : Date of receipt of test item ...................... : 09 Jun., 2025 Date (s) of performance of tests ............. : 10 Jun., to 23 Jun., 2025 Date of Issue .......................................... : 24 Jun., 2025 Test Result .............................................. : Pass Testing Engineer : (Aaron Bu) Technical Manager : (Skylar Li) Authorized Signatory : (Bovey Yang) Page 3 of 8 Report No.: STS2512107H01 TABLE OF CONTENTS 1. GENERAL INFORMATION 5 1.1 GENERAL DESCRIPTION OF THE EUT 5 1.2 TEST FACTORY 5 2. FCC 47CFR §2.1093 REQUIREMENT 6 2.1 TEST STANDARDS 6 2.2 LIMIT 6 2.3 TEST RESULT 8 Evaluation Result 8 Page 4 of 8 Report No.: STS2512107H01 Revision History Rev. Issue Date Report No. Effect Page Contents 00 24 Jun., 2025 STS2512107H01 ALL Initial Issue Page 5 of 8 Report No.: STS2512107H01 1. GENERAL INFORMATION 1.1 GENERAL DESCRIPTION OF THE EUT Product Name CAR ALARM Brand Name N/A Model Name TR210 Series Model(s) N/A Model Difference N/A Product Description The EUT is CAR ALARM Operation Frequency: 433.92MHz Modulation Type: FSK Antenna gain: 2.0 dBi Antenna Designation: HELIX Antenna Power Rating DC 6V Adapter N/A Battery 3V Lithium Battery(CR2016) * 2 Hardware Version N/A Software Version N/A 1.2 TEST FACTORY SHENZHEN STS TEST SERVICES CO., LTD Add. : 101, Building B, Zhuoke Science Park, No.190 Chongqing Road, ZhanChengShequ, Fuhai Sub-District, Bao’an District, Shenzhen, Guang Dong, China FCC test Firm Registration Number: 625569 IC test Firm Registration Number: 12108A A2LA Certificate No.: 4338.01 Page 6 of 8 Report No.: STS2512107H01 2. FCC 47CFR §2.1093 REQUIREMENT 2.1 TEST STANDARDS The limit for Maximum Permissible Exposure (MPE) specified in KDB 447498 D01 General RF Exposure Guidance v06 is followed. The gain of the antennas used in the product is extracted from the Antenna data sheets provided and also the maximum total power input to the antenna is measured. Through the Friis transmission formula and the maximum gain of the antenna, we can calculate the distance, away from the product, where the limit of MPE is reached. Although the Friis Transmission formula is far field assumption, the calculated result of that is an over-prediction for near field power density. It is taken as worst case to specify the safety range. 2.2 LIMIT Approximate SAR Test Exclusion Power Thresholds at Selected Frequencies and Test Separation Distances are illustrated in the following Table. Page 7 of 8 Report No.: STS2512107H01 The 1-g and 10-g SAR test exclusion thresholds for 100 MHz to 6 GHz at test separation distances ≤ 50 mm are determined by: [(max. power of channel, including tune-up tolerance, mW)/(min. test separation distance, mm)] • [√f(GHz)] ≤ 3.0 for 1-g SAR and ≤ 7.5 for 10-g extremity SAR,where f(GHz) is the RF channel transmit frequency in GHz. Power and distance are rounded to the nearest mW and mm before calculation The result is rounded to one decimal place for comparison The test exclusions are applicable only when the minimum test separation distance is ≤ 50 mm and for transmission frequencies between 100 MHz and 6 GHz. When the minimum test separation distance is < 5 mm, a distance of 5 mm is applied to determine SAR test exclusion. Page 8 of 8 Report No.: STS2512107H01 2.3 TEST RESULT Maximum measured transmitter power. Worst Case According to the calculation formula of power: EIRP = P*G = (E*d) 2 /30 Where: P = transmitter output power in watts, G = numeric gain of the antenna in the direction of interest relative to an isotropic radiator (unitless), E = electric field strength in V/m, --- 10 ((dBuV/m)/20) /10 6 , d = measurement distance in meters (m)---3m, So, P = (E*d) 2 /(30 *G) Evaluation Result Mode Frequency Antenna Distance RF output power including tune up (dBm) SAR Test Exclusion Threshold SAR Test Exclusion Estimated SAR GHz mm dBm mw 433.92(FSK) 0.43392 5 -7.0 0.2 0.026 Yes / Note: 1. Remark: The worst case gain of the antenna is 2.0dBi. 2. Threshold at which no SAR required is 0.026 ≤ 3.0 for 1-g SAR, Separation distance ≤ 5mm. ※※※※※END OF THE REPORT※※※※※ Frequency (MHz) Maximum field strength@3m ( dBuV/m) Maximum field strength@3m (V/m) Antenna Gain (dBi) Antenna Gain (numeric) Distance (m) Output power ( dBm ) 433.92 90.10 0.032 2 1.58 3 -7.1

The test results presented in this report relate only to the object tested. This report shall not be reproduced, except in full, without the written approval of the Shenzhen STS Test Services Co., Ltd. Radio Test Report Report No.:STS2512107W01 Issued for Automotive Data Solutions Inc. 8400 Bougainville Montreal Quebec Canada H4P 2G1 Product Name: CAR ALARM Brand Name: N/A Model Name: TR210 Series Model(s): N/A FCC ID: 2AEPJ-TR210 Test Standards: FCC Part 15.231 Page 2 of 30 Report No.: STS2512107W01 TEST REPORT Applicant’s Name .................: Automotive Data Solutions Inc. Address ..................................: 8400 Bougainville Montreal Quebec Canada H4P 2G1 Manufacturer's Name ...........: DONGGUAN PORTMAN ELECTRONIC SCIENCE AND TECHNOLOGY Address ..................................: NO.10, LUYI 2 ROAD,TANGXIA TOWN, DONGGUAN CITY GUANGDONG Product Description Product Name ............................ : CAR ALARM Brand Name ............................... : N/A Model Name ...........................: TR210 Series Model(s) ....................: N/A Test Standards .......................... : FCC Part 15.231 Test Procedure ........................... : ANSI C63.10-2020 This device described above has been tested by STS, the test results show that the equipment under test (EUT) is in compliance with the FCC/IC requirements. And it is applicable only to the tested sample identified in the report. The test results presented in this report relate only to the object tested. This report shall not be reproduced, except in full, without the written approval of the Shenzhen STS Test Services Co., Ltd. Date of Test ............................: Date of Receipt of Test Item ...: 09 Jun., 2025 Date of performance of tests ..: 10 Jun., to 23 Jun., 2025 Date of Issue ..........................: 24 Jun., 2025 Test Result .............................: Pass Testing Engineer : (Aaron Bu) Technical Manager : (Skylar Li) Authorized Signatory : (Bovey Yang) Page 3 of 30 Report No.: STS2512107W01 TABLE OF CONTENTS Page 1. SUMMARY OF TEST RESULTS 6 1.1 TEST FACTORY 6 1.2 MEASUREMENT UNCERTAINTY 6 2. GENERAL INFORMATION 7 2.1 GENERAL DESCRIPTION OF THE EUT 7 2.2 DESCRIPTION OF THE TEST MODES 8 2.3 BLOCK DIAGRAM SHOWING THE CONFIGURATION OF SYSTEM TESTED 8 2.4 DESCRIPTION OF NECESSARY ACCESSORIES AND SUPPORT UNITS 9 2.5 EQUIPMENTS LIST 10 3. EMC EMISSION TEST 11 3.1 CONDUCTED EMISSION MEASUREMENT 11 3.2 TEST PROCEDURE 12 3.3 TEST SETUP 12 3.4 TEST RESULTS 12 4. RADIATED EMISSION MEASUREMENT 13 4.1 RADIATED EMISSION LIMITS 13 4.2 TEST PROCEDURE 15 4.3 DEVIATION FROM TEST STANDARD 15 4.4 TEST SETUP 16 4.5 EUT OPERATING CONDITIONS 17 4.6 TEST RESULTS 17 4.7 FIELD STRENGTH CALCULATION 18 5. BANDWIDTH TEST 23 5.1 LIMIT 23 5.2 TEST REQUIREMENTS 23 5.3 TEST PROCEDURE 23 5.4 TEST SETUP 23 5.5 EUT OPERATION CONDITIONS 23 5.6 TEST RESULTS 24 6. DUTY CYCLE 25 6.1 TEST PROCEDURE 25 6.2 TEST SETUP 25 6.3 EUT OPERATION CONDITIONS 25 6.4 TEST RESULTS 26 7. AUTOMATICALLY DEACTIVATE 27 Page 4 of 30 Report No.: STS2512107W01 TABLE OF CONTENTS Page 7.1 STANDARD REQUIREMENT 27 7.2 TEST PROCEDURE 27 8. ANTENNA REQUIREMENT 29 8.1 STANDARD REQUIREMENT 29 8.2 EUT ANTENNA 29 APPENDIX 1-PHOTOS OF TEST SETUP 30 Page 5 of 30 Report No.: STS2512107W01 Revision History Rev. Issue Date Report No. Effect Page Contents 00 24 Jun., 2025 STS2512107W01 ALL Initial Issue Page 6 of 30 Report No.: STS2512107W01 1. SUMMARY OF TEST RESULTS Test procedures according to the technical standards: FCC Part 15.231,Subpart C Standard Section Test Item Judgment Remark 15.207 Conducted Emission N/A -- 15.205(a)/15.209/ 15.231.(b) Radiated Spurious Emission PASS -- 15.231(a)(1)/ 15.231(b)(2) Transmission requirement PASS -- 15.231(C) 20 dB Bandwidth PASS -- 15.203 Antenna Requirement PASS -- Note: (1) “N/A” denotes test is not applicable in this Test Report. (2) All tests are according to ANSI C63.10-2020. 1.1 TEST FACTORY SHENZHEN STS TEST SERVICES CO., LTD Add. :101, Building B, Zhuoke Science Park, No.190 Chongqing Road, ZhanChengShequ, Fuh ai Sub-District, Bao’an District, Shenzhen, Guang Dong, China FCC test Firm Registration Number: 625569 FCC test Firm Designation Number: CN1203 IC test Firm Registration Number: 12108A A2LA Certificate No.: 4338.01 1.2 MEASUREMENT UNCERTAINTY The reported uncertainty of measurement y ±U, where expended uncertainty U is based on a standard uncertainty multiplied by a coverage factor of k=2, providing a level of confidence of approximately 95 %. No. Item Uncertainty 1 RF output power, conducted ±0.751dB 2 Unwanted Emissions, conducted ±2.888dB 3 All emissions, radiated 9K-30MHz ±2.48dB 4 All emissions, radiated 30M-1GHz ±2.52dB 5 All emissions, radiated 1G-18GHz ±3.48dB 6 All emissions, radiated>18GHz ±4.18dB 7 Conducted Emission (9KHz-150KHz) ±2.48dB 8 Conducted Emission (150KHz-30MHz) ±2.52dB 9 Occupied Channel Bandwidth ±3.6% 10 Power Spectral Density, conducted ±1.214dB 11 Duty Cycle ±3.2% Page 7 of 30 Report No.: STS2512107W01 2. GENERAL INFORMATION 2.1 GENERAL DESCRIPTION OF THE EUT Product Name CAR ALARM Trade Name N/A Model Name TR210 Series Model N/A Model Difference N/A Product Description The EUT is a CAR ALARM Operation Frequency: 433.92MHz Modulation Type: FSK Antenna Designation: HELIX Antenna Antenna Gain(Peak) 2.0 dBi More details of EUT technical specification, please refer to the User Manual. Channel List Please refer to the Note 3. Power Rating DC 6V Adapter N/A Battery 3V Lithium Battery(CR2016)*2 Hardware version number N/A Software version number/FVIN N/A Connecting I/O Port(s) Please refer to the Note 1. Note: 1. For a more detailed features description, please refer to the manufacturer’s specifications orthe User Manual. 2. Table for filed Antenna Ant. Brand Model Name Antenna Type Connector Gain (dBi) NOTE 1 POETMAN 433MHz-ANT HELIX N/A 2 Antenna Note: The antenna information refer the manufacturer provide report, applicable only to the tested sample identified in the report. 3. Channel Lis…

Text truncated - open the document above for the full version.

433MHz-ANT Antenna Specification The antenna radiation pattern measurements are carried out in an anechoic chamber. Radiation patterns are presented for 3D; XZ planes with horizontal and vertical polarization of the receiving antenna. Measurements are carried out for the module installed in the upper right corner on the reference board with no laminate below the antenna trace. 17MM 4.7MM 433MHz-ANT Radiation Pattern for Antenna Trace Figure1: 3D Gain:2.0dBi Figure2: Radiation Pattern for XZ-Plane, Horizontal Polarization Model number 433MHz-ANT Antenna Manufacturer’s name & address Company: DONGUANG POETMAN EIECTRONIC SCIENCE AND TECHNOLOGY CO, Name: Wayne Ding Add: NO,10,LUYI 2 ROAD ,TANGXIA TOWN,DONGGUAN CITY GUANGDONG PROVINCE Email: [email protected]

FCC ID: 2AEPJ-TR210 Page 1 of 2 Setup Photos Radiated Spurious Emission Below 1GHz Above 1GHz FCC ID: 2AEPJ-TR210 Page 2 of 2 Conducted method ------End------