2AFH27199-77IFIDELITY NOISE REDUCTION WARP BLUETOOTH HEADPHONES

 X5BT hi-fi hands-free Bluetooth Headset instructions Dear Customer: Hello! Welcome to use X5BT hi-fi hands-free Bluetooth Noise-cancelling Headset,Please read instruction carefully before you use the equipment. ! Don’t use it in places near water. ! Don’t use it in places near heat sources. ! The sound is adjusted to the proper volume so as not to damage the health and your equipment. Brief introduction of X6BT high fidelity hands-free Bluetooth Headset features --------------------------------------------------------------------- 1. Bluetooth mode Wireless Bluetooth capable of receiving line audio transmission within 10M. And Headset reverse control part of Bluetooth devices such as play, pause, next song selection, support iPhone, iPad (partial player software does not support the reverse control). Telephone answering, Headset switching, high fidelity voice,clear voice quality,no echo. 2.Call the hands-free function Telephone answering, Headset switching, high fidelity voice, clear voice quality,no reply. 3.The Line IN input function Use the audio line and the Line in interface, can be depleted in the Headset battery case to continue to listen to music. 4.Automatic back even, memory play function Through this function can automatically return to the last successful connect to Bluetooth devices and memory play before the shutdown of music playback progress. 5.The Micro USB port charging function Micro USB charging, convenient and simple. 6.Low battery alarm, shutdown function Battery power is insufficient Headset have low battery alarm and automatic shutdown function. 7.Noise-cancelling function Open ON/OFF,reduce outside noise. Interface / key function description 1.The previous song / volume + button Pairing in Bluetooth connection state, short a press to switch; long press (2seconds), the volume gradually increases, alarm and prompt after reaching the maximum. 2.The next song / volume - button Pairing in Bluetooth connection state, short press for a switch; long press (2seconds), the volume gradually reduced, as to the minimum volume will mute. 3.The on / off key / play / pause / hand free key Long press the power on or off; in the playing state, short press to pause / play,short press according to answer the phone when the phone access; long press two seconds to rejected when you didn’t want to answer the phone. (blue, red indicator on the button below) 4.Line in interface. 5.Micro USB charging port 6.Noise-Cancelling ON/OFF Push down the switch ,indictor light shows green color for entering noise-cancelling mode The basic operating instructions: 1.Long press the power on button, enter the Bluetooth mode, Headset will be issued a "dongdongdongdong" prompt tone, continue to grow by about 3 seconds of red and blue lights flashing, the pairing is successful, Headset will be issued a "dongdong" prompt tone, equipment connected to normal after the blue indicator light for about 3 seconds a speed flash, not connected Bluetooth will flashing red and blue lights. Bluetooth Headset Username: X5BT; 2.In the Bluetooth mode have telephone access short press the power button to answer the call, call a short press this key to hang up the telephone; telephone access, if no need to answer the phone, can press the start button 2-3 seconds to reject; 3.In the Bluetooth mode,short press key ①,can change to previous song. long press the volume increase 4.In the Bluetooth mode,short press key ②,can change to next song., long press the volume reduction 5.Any state, insert the Line audio input line, can be automatically converted to Line mode. 6.Plug in the Micro USB line connected to the computer USB port or adapter power supply charging, the red indicator light bright when charging, the red indicator light gone and the blue indicator light bright means the battery is full of electricity . Recommended charging in shutdown state. 7.Bluetooth only can one by one connection, only can operate a connected device,you cannot deleted in the connected state , you need to disconnect to delete it. 8.When bluetooth list in the one player equipment, it is not allowed to have the same name of Bluetooth device, otherwise it will cause can't find another similar or the same Bluetooth Headset. 9.Bluetooth/Line in,Music Moel can change Noise-cancelling. Technical parameters of the product 1.Product size: 180mm (L) *180mm (W) 2.Product weight: Headset parameters: 1 speaker diameter: 40MM. 2 The impedance: 16 ohm. 3 the rated audio output power: 5mW. 4 sensitivity: 106 ± 3DB. 5 Peak power output: ≤10mA Bluetooth Noise-cancelling parameters: 1.Frequency: 2.402GHZ-2.480GHZ; 2.Bluetooth technology: CSR4.0 3.The receiving sensitivity; -80dBm<0.1%BER; 4.The Straight line transport range: 10 meters; 5.Data transfer rate: 115200bps; 6.Operating power consumption: less than 45MA; 7.Noise-cancelling mode:results of Noice-cancelling ≥15db Battery parameters: 1.Battery specifications: Standard: 350MAH built-in battery 2 .Time of Bluetooth endurance: up to 5-8hours (based on 50% voice volume) Time/Time of Noise-cancelling endurance:up to 5-8hours(based on 50% voice volume) (If playing high bit rate or high sampling rate, audio, playing time will shorten appropriately) 3.The charging standards: AC 100V ~ 240v/50-60Hz, 5v/300 ~ 500MA output(must use the charger standards in line with international standards, or use computer USB port charging so as not to damage the equipment) 4.Time required for charging:about 2-4 hours (depending on the different sizes of charging current and different charging time) Packing list A headset host One pc LINE-IN audio line One pc USB charging line An operating instructions Use the matters needing attention 1.Set in the mobile phone Bluetooth, and the machine matching options check the phone (for mobile phone audio) state, in order to hands free. 2.This product has the anti-interference design of anti Bluetooth signal, you can prevent the signal interference effectively; but there will still be interfere…

Text truncated - open the document above for the full version.

RWD INDUSRIAL CO., LTD 3F, Block 1, Chuangxinghong Industrial Zone, Dashuikeng, No.1398, Guanguang Rd, Guanlan, Bao’an District, Shenzhen, China DATE :2015-11-25 Nemko Canada Inc 303 River Road Ottawa, Ontario, Canada K1V 1H2 Attn: Director of Certification Authority to Act as Agent On our behalf, I appoint Kevin Yu of Shenzhen EBO Technology Co., Ltd. to act as our agent in the preparation of this application for equipment certification. I certify that submitted documents properly describe the device or system for which equipment certification is sought. I also certify that each unit manufactured, imported or marketed, as defined in the Federal Communications Commission’s regulations will have affixed to it a label identical to that submitted for approval with this application. For instances where our authorized agent signs the application for certification on our behalf, I acknowledge that all responsibility for complying with the terms and conditions for certification, as specified by Nemko Canada Inc, still resides with RWD INDUSRIAL CO., LTD and 3F, Block 1, Chuangxinghong Industrial Zone, Dashuikeng, No.1398, Guanguang Rd, Guanlan, Bao’an District, Shenzhen, China Dated this / Day of 25/11/2015 / Agency agreement expiration date: 24/11/2016 By: Raincy Jin Signature Printed Title: Marketing Executive On behalf of : RWD INDUSRIAL CO., LTD Telephone: +86 13823348480

RWD INDUSRIAL CO., LTD 3F, Block 1, Chuangxinghong Industrial Zone, Dashuikeng, No.1398, Guanguang Rd, Guanlan, Bao’an District, Shenzhen, China DATE :2015-11-25 Equipment Autorisation Division Federal Communications Commission 7435 Oakland Mills Road Columbia, MD 21046 FCC ID: 2AFH27199-77 Product Name: IFIDELITY NOISE REDUCTION WARP BLUETOOTH HEADPHONES Request for Long-term Confidentiality Pursuant to Sections 0.457 and 0.459 of the commission rules, we hereby request that the following documents be held confidential long term:  Block diagram  Schematics  Operational Description These documents contain detailed system and equipment description and related information about the product which RWD INDUSRIAL CO., LTD. considers to be proprietary, confidential, and a custom design and, otherwise would not release to the general public. Since this design is a basis from which future technological products will evolve, RWD INDUSRIAL CO., LTD. Considers this information to be of benefit to its competitors, and that the disclosure of information in these documents would give competitors an unfair advantage in the market Dated this / Day of 25/11/2015 / By: Raincy Jin Signature Printed Title: Marketing Executive On behalf of : RWD INDUSRIAL CO., LTD Telephone: +86 13823348480

Differences Declaration To whom concern, We, RWD INDUSRIAL CO., LTD hereby declares: The product model(s) RWD-X5BTANC, 7199-77 are identical in the PCB layout, interior structure and electrical circuits with the product model 7199-66, the only differences are the model name for commercial purpose. Authorized signature:  Position: Marketing Executive Date: 201511/25 7199-77

External Photos of EUT Sample

Label

Internal Photos of EUT Sample

RF Exposure evaluation According to KDB 447498 D01 General RF Exposure Guidance v05 The 1-g and 10-g SAR test exclusion thresholds for 100 MHz to 6 GHz at test separation distances ≤ 50 mm are determined by: [(max. power of channel, including tune-up tolerance, mW)/(min. test separation distance, mm)] ·[√f(GHz)] ≤ 3.0 for 1-g SAR and ≤ 7.5 for 10-g extremity SAR, where f(GHz) is the RF channel transmit frequency in GHz Power and distance are rounded to the nearest mW and mm before calculation The result is rounded to one decimal place for comparison eirp = pt x gt = (EXd) 2 /30 where: pt = transmitter output power in watts, gt = numeric gain of the transmitting antenna (unitless), E = electric field strength in V/m, --- 10 ((dBuV/m)/20) /10 6 d = measurement distance in meters (m)---3m So pt = (EXd) 2 /30 x gt Field strength = 94.64dBuV/m @3m Ant gain 0dBi; so Ant numeric gain=1 So pt={[10 (94.64/20) /10 6 x3] 2 /(30x1)}x1000mW = 0.87 mW So (0.87 mW/5mm)x √2.480 GHz = 0.3 <3 Then SAR evaluation is not required

Shenzhen EBO Technology Co., Ltd . 1-4F, Huafeng Science Park, Xin’an Sixth Road, 82 th District, Bao’an, Shenzhen, China. Telephone: +86-755-29451282, Fax: +86-755-22639141 Report No.: EBO1511061-E209 Page: 1 of 29 Authorized Signature: Kevin Yu Laboratory Manager This report details the results of the testing carried out on one sample. The results contained in this test report do not relate to other samples of the same product and does not permit the use of the EBO product certification mark. The manufacturer should ensure that all products in series production are in conformity with the product sample detailed in this report. This report may only be reproduced and distributed in full. If the product in this report is used in any configuration other than that detailed in the report, the manufacturer must ensure the new system complies with all relevant standards. Any mention of EBO International Electrical Approvals or testing done by EBO International Electrical Approvals in connection with, distribution or use of the product described in this report must be approved by EBO International Electrical Approvals in writing. This document cannot be reproduced except in full, without prior written approval of the Company. Any unauthorized alteration, forgery or falsification of the content or appearance of this document is unlawful and offenders may be prosecuted to the fullest extent of the law. Unless otherwise stated the results shown in this test report refer only to the sample(s) tested and such sample(s) are retained for 90 days only FCC REPORT Applicant: RWD INDUSRIAL CO., LTD Address of Applicant: 3F, Block1, Chuangxinghong Industrial Zone, Dashuikeng, No1398 Guanguang Rd, Guanlan, Bao’an District, Shenzhen, China Equipment Under Test (EUT) Product Name: IFIDELITY NOISE REDUCTION WARP BLUETOOTH HEADPHONES Trade Mark: LEEDS Model No.: 7199-77, RWD-X5BTANC FCC ID: 2AFH27199-77 Applicable standards: FCC CFR Title 47 Part 15 Subpart C Section 15.249:2014 Date of sample receipt: November 17, 2015 Date of Test: November 17, 2015 To November 25, 2015 Date of report issued: November 25, 2015 Test Result : PASS * * In the configuration tested, the EUT complied with the standards specified above. Shenzhen EBO T echnology Co., Ltd . Report No.: EBO1511061-E209 Page: 2 of 29 This document is issued by the Company subject to its General Conditions of Service printed overleaf, available on request or accessible at http://www.ebotek.cn 2 Version Version No. Date Description 00 November 25, 2015 Original Prepared By: Date: November 25, 2015 Project Engineer Check By: Date: November 25, 2015 Reviewer and, for electronic format documents, subject to Terms and Conditions for Electronic Documents at http://www.ebotek.cn . Attention is drawn to the limitation of liability, indemnification and jurisdiction issues defined therein. Any holder of this document is advised that information contained hereon reflects the Company’s findings at the time of its intervention only and within the limits of Client’s instructions, if any. The Company’s sole responsibility is to its Client and this document does not exonerate parties to a transaction from exercising all their rights and obligations under the transaction documents. This document cannot be reproduced except in full, without prior written approval of the Company. Any unauthorized alteration, forgery or falsification of the content or appearance of this document is unlawful and offenders may be prosecuted to the fullest extent of the law. Unless otherwise stated the results shown in this test report refer only to the sample(s) tested and such sample(s) are retained for 90 days only.” Shenzhen EBO T echnology Co., Ltd . Report No.: EBO1511061-E209 Page: 3 of 29 This document is issued by the Company subject to its General Conditions of Service printed overleaf, available on request or accessible at http://www.ebotek.cn and, for electronic format documents, subject to Terms and Conditions for Electronic Documents at http://www.ebotek.cn . Attention is drawn to the limitation of liability, indemnification and jurisdiction issues defined therein. Any holder of this document is advised that information contained hereon reflects the Company’s findings at the time of its intervention only and within the limits of Client’s instructions, if any. The Company’s sole responsibility is to its Client and this document does not exonerate parties to a transaction from exercising all their rights and obligations under the transaction documents. This document cannot be reproduced except in full, without prior written approval of the Company. Any unauthorized alteration, forgery or falsification of the content or appearance of this document is unlawful and offenders may be prosecuted to the fullest extent of the law. Unless otherwise stated the results shown in this test report refer only to the sample(s) tested and such sample(s) are retained for 90 days only.” 3 Contents Page 1 COVER PAGE ...........................................................................................................................................1 2 VERSION..................................................................................................................................................2 3 CONTENTS..............................................................................................................................................3 4 TEST SUMMARY.....................................................................................................................................4 4.1 MEASUREMENT UNCERTAINTY............................................................................................................ 4 5 GENERAL INFORMATION...................................................................................................................... 5 5.1 CLIENT INFORMATION.....................................................................................................…

Text truncated - open the document above for the full version.

Shenzhen EBO Technology Co., Ltd . 1-4F, Huafeng Science Park, Xin’an Sixth Road, 82 th District, Bao’an, Shenzhen, China. Telephone: +86-755-29451282, Fax: +86-755-22639141 Report No.: EBO1511061-E210 Page: 1 of 25 Authorized Signature: Kevin Yu Laboratory Manager This report details the results of the testing carried out on one sample. The results contained in this test report do not relate to other samples of the same product and does not permit the use of the EBO product certification mark. The manufacturer should ensure that all products in series production are in conformity with the product sample detailed in this report. This report may only be reproduced and distributed in full. If the product in this report is used in any configuration other than that detailed in the report, the manufacturer must ensure the new system complies with all relevant standards. Any mention of EBO International Electrical Approvals or testing done by EBO International Electrical Approvals in connection with, distribution or use of the product described in this report must be approved by EBO International Electrical Approvals in writing. This document cannot be reproduced except in full, without prior written approval of the Company. Any unauthorized alteration, forgery or falsification of the content or appearance of this document is unlawful and offenders may be prosecuted to the fullest extent of the law. Unless otherwise stated the results shown in this test report refer only to the sample(s) tested and such sample(s) are retained for 90 days only FCC REPORT Applicant: RWD INDUSRIAL CO., LTD Address of Applicant: 3F, Block1, Chuangxinghong Industrial Zone, Dashuikeng, No1398 Guanguang Rd, Guanlan, Bao’an District, Shenzhen, China Equipment Under Test (EUT) Product Name: IFIDELITY NOISE REDUCTION WARP BLUETOOTH HEADPHONES Trade Mark: LEEDS Model No.: 7199-77, RWD-X5BTANC FCC ID: 2AFH27199-77 Applicable standards: FCC CFR Title 47 Part 15 Subpart C Section 15.249:2014 Date of sample receipt: November 17, 2015 Date of Test: November 17, 2015 To November 25, 2015 Date of report issued: November 25, 2015 Test Result : PASS * * In the configuration tested, the EUT complied with the standards specified above. Shenzhen EBO Technology Co., Ltd . Report No.: EBO1511061-E210 Page: 2 of 25 This document is issued by the Company subject to its General Conditions of Service printed overleaf, available on request or accessible at http://www.ebotek.cn 2 Version Version No. Date Description 00 November 25, 2015 Original Prepared By: Date: November 25, 2015 Project Engineer Check By: Date: November 25, 2015 Reviewer and, for electronic format documents, subject to Terms and Conditions for Electronic Documents at http://www.ebotek.cn. Attention is drawn to the limitation of liability, indemnification and jurisdiction issues defined therein. Any holder of this document is advised that information contained hereon reflects the Company’s findings at the time of its intervention only and within the limits of Client’s instructions, if any. The Company’s sole responsibility is to its Client and this document does not exonerate parties to a transaction from exercising all their rights and obligations under the transaction documents. This document cannot be reproduced except in full, without prior written approval of the Company. Any unauthorized alteration, forgery or falsification of the content or appearance of this document is unlawful and offenders may be prosecuted to the fullest extent of the law. Unless otherwise stated the results shown in this test report refer only to the sample(s) tested and such sample(s) are retained for 90 days only.” Shenzhen EBO Technology Co., Ltd . Report No.: EBO1511061-E210 Page: 3 of 25 This document is issued by the Company subject to its General Conditions of Service printed overleaf, available on request or accessible at http://www.ebotek.cn and, for electronic format documents, subject to Terms and Conditions for Electronic Documents at http://www.ebotek.cn. Attention is drawn to the limitation of liability, indemnification and jurisdiction issues defined therein. Any holder of this document is advised that information contained hereon reflects the Company’s findings at the time of its intervention only and within the limits of Client’s instructions, if any. The Company’s sole responsibility is to its Client and this document does not exonerate parties to a transaction from exercising all their rights and obligations under the transaction documents. This document cannot be reproduced except in full, without prior written approval of the Company. Any unauthorized alteration, forgery or falsification of the content or appearance of this document is unlawful and offenders may be prosecuted to the fullest extent of the law. Unless otherwise stated the results shown in this test report refer only to the sample(s) tested and such sample(s) are retained for 90 days only.” 3 Contents Page 1 COVER PAGE............................................................................................................................................ 1 2 VERSION..................................................................................................................................................2 3 CONTENTS..............................................................................................................................................3 4 TEST SUMMARY.....................................................................................................................................4 5 GENERAL INFORMATION...................................................................................................................... 5 5.1 CLIENT INFORMATION......................................................................................................................... 5 5.2 GENERAL DESCRIPTION OF EUT........................................................................................…

Text truncated - open the document above for the full version.

TEST SETUP PHOTOGRAPHS 1. Conducted Emission Test Setup 2. Radiated Emission Test Setup