2AG87RM1700-1NMesh Rider Radio

Integration instructions for host product manufacturers according to KDB 996369 D03 OEM Manual v01r01 2.2 List of applicable FCC rules CFR 47 FCC Part 15 Subpart C has been investigated. It is applicable to the modular transmitter 2.3 Specific Operational Use Conditions - Antenna Placement Within the Host Platform The module is tested for standalone mobile RF exposure use condition. ● The antenna must be installed such that 20cm is maintained between the antenna and users, ● The transmitter module may not be co-located with any other transmitter or antenna. In the event that these conditions cannot be met (for example certain laptop configurations or co-location with another transmitter), then the FCC authorization is no longer considered valid and the FCC ID cannot be used on the final product. In these circumstances, the OEM integrator will be responsible for re-evaluating the end product (including the transmitter) and obtaining a separate FCC authorization. 2.4 Limited Module Procedures Not applicable 2.5 Trace Antenna Designs Not applicable 2.6 RF Exposure Considerations This device complies with FCC radiation exposure limits set forth for an uncontrolled environment. This equipment should be installed and operated with minimum distance 20cm between the radiator & your body. 2.7 Antenna Type and Gain The following antennas have been certified for use with this module. Only antennas of the same type with equal or lower gain may also be used with this module. Other types of antennas and/or higher gain antennas may require the additional authorization for operation. Antenna Specification list below: Model No. Manufacturer Type of Antenna and Gain (Max.) Frequency Range 001-0002 TE Connectivity Laird External Antenna, Dipole, 2.0dBi (Max.) 902 ~ 928 MHz RN-SMA4-RP Microchip External Antenna, Dipole, 2.2dBi (Max.) 2400 ~ 2500 MHz 2.8 End Product Labelling Compliance Information When the module is installed in the host device, the FCC ID label must be visible through a window on the final device or it must be visible when an access panel, door or cover is easily removed. If not, a second label must be placed on the outside of the final device that contains the following text: “Contains FCC ID: 2AG87RM1700-1N”. The FCC ID can be used only when all FCC compliance requirements are met. 2.9 Information on Test Modes and Additional Testing Requirements This transmitter is tested in a standalone mobile RF exposure condition and any co-located or simultaneous transmission with other transmitter(s) class II permissive change re- evaluation or new FCC authorization. Host manufacturer installed this modular with single modular approval should perform the test of radiated emission and spurious emission according to FCC part 15C, 15.209, 15.207 requirement, only if the test result comply with FCC part 15C, 15.209, 15.207 requirement, then the host can be sold legally. 2.10 Additional testing, Part 15 Subpart B Disclaimer This transmitter modular us tested as a subsystem and its certification does not cover the FCC Part 15 Subpart B rules requirement applicable to the final host. The final host will still need to be reassessed for compliance to this portion of rules requirements if applicable. As long as all conditions above are met, further transmitter test will not be required. However, the OEM integrator is still responsible for testing their end-product for any additional compliance requirements required with this modular installed. 2.11 Manual Information to The End User The OEM integrator has to be aware not to provide information to the end user regarding how to install or remove this RF module in the user’s manual of the end product which integrates this module. The host integrator must follow the integration instructions provided in this document and ensure that the composite system end product complies with the requirements by a technical assessment or evaluation to the rules and to KDB Publication 996369. The host integrator installing this module into their product must ensure that the final composite product complies with the requirements by a technical assessment or evaluation to the rules, including the transmitter operation and should refer to guidance in KDB Publication 996369. OEM/Host Manufacturer Responsibilities OEM/Host manufacturers are ultimately responsible for the compliance of the Host and Module. The final product must be reassessed against all the essential requirements of the FCC rule such as FCC Part 15 Subpart B before it can be placed on the US market. This includes reassessing the transmitter module for compliance with the Radio and RF Exposure essential requirements of the FCC rules. 2.12 How to Make Changes - Important Note In the event that these conditions cannot be met (for example certain laptop configurations or co-location with another transmitter), then the FCC authorization is no longer considered valid and the FCC ID cannot be used on the final product. In these circumstances, the OEM integrator will be responsible for re-evaluating the end product (including the transmitter) and obtaining a separate FCC authorization.

Integration instructions for host product manufacturers according to KDB 996369 D03 OEM Manual v01r01 2.2 List of applicable FCC rules CFR 47 FCC Part 15 Subpart C has been investigated. It is applicable to the modular transmitter 2.3 Specific Operational Use Conditions - Antenna Placement Within the Host Platform The module is tested for standalone mobile RF exposure use condition. ● The antenna must be installed such that 20cm is maintained between the antenna and users, ● The transmitter module may not be co-located with any other transmitter or antenna. In the event that these conditions cannot be met (for example certain laptop configurations or co-location with another transmitter), then the FCC authorization is no longer considered valid and the FCC ID cannot be used on the final product. In these circumstances, the OEM integrator will be responsible for re-evaluating the end product (including the transmitter) and obtaining a separate FCC authorization. 2.4 Limited Module Procedures Not applicable 2.5 Trace Antenna Designs Not applicable 2.6 RF Exposure Considerations This device complies with FCC radiation exposure limits set forth for an uncontrolled environment. This equipment should be installed and operated with minimum distance 20cm between the radiator & your body. 2.7 Antenna Type and Gain The following antennas have been certified for use with this module. Only antennas of the same type with equal or lower gain may also be used with this module. Other types of antennas and/or higher gain antennas may require the additional authorization for operation. Antenna Specification list below: Model No. Manufacturer Type of Antenna and Gain (Max.) Frequency Range 001-0002 TE Connectivity Laird External Antenna, Dipole, 2.0dBi (Max.) 902 ~ 928 MHz RN-SMA4-RP Microchip External Antenna, Dipole, 2.2dBi (Max.) 2400 ~ 2500 MHz 2.8 End Product Labelling Compliance Information When the module is installed in the host device, the FCC ID label must be visible through a window on the final device or it must be visible when an access panel, door or cover is easily removed. If not, a second label must be placed on the outside of the final device that contains the following text: “Contains FCC ID: 2AG87RM1700-1N”. The FCC ID can be used only when all FCC compliance requirements are met. 2.9 Information on Test Modes and Additional Testing Requirements This transmitter is tested in a standalone mobile RF exposure condition and any co-located or simultaneous transmission with other transmitter(s) class II permissive change re- evaluation or new FCC authorization. Host manufacturer installed this modular with single modular approval should perform the test of radiated emission and spurious emission according to FCC part 15C, 15.209, 15.207 requirement, only if the test result comply with FCC part 15C, 15.209, 15.207 requirement, then the host can be sold legally. 2.10 Additional testing, Part 15 Subpart B Disclaimer This transmitter modular us tested as a subsystem and its certification does not cover the FCC Part 15 Subpart B rules requirement applicable to the final host. The final host will still need to be reassessed for compliance to this portion of rules requirements if applicable. As long as all conditions above are met, further transmitter test will not be required. However, the OEM integrator is still responsible for testing their end-product for any additional compliance requirements required with this modular installed. 2.11 Manual Information to The End User The OEM integrator has to be aware not to provide information to the end user regarding how to install or remove this RF module in the user’s manual of the end product which integrates this module. The host integrator must follow the integration instructions provided in this document and ensure that the composite system end product complies with the requirements by a technical assessment or evaluation to the rules and to KDB Publication 996369. The host integrator installing this module into their product must ensure that the final composite product complies with the requirements by a technical assessment or evaluation to the rules, including the transmitter operation and should refer to guidance in KDB Publication 996369. OEM/Host Manufacturer Responsibilities OEM/Host manufacturers are ultimately responsible for the compliance of the Host and Module. The final product must be reassessed against all the essential requirements of the FCC rule such as FCC Part 15 Subpart B before it can be placed on the US market. This includes reassessing the transmitter module for compliance with the Radio and RF Exposure essential requirements of the FCC rules. 2.12 How to Make Changes - Important Note In the event that these conditions cannot be met (for example certain laptop configurations or co-location with another transmitter), then the FCC authorization is no longer considered valid and the FCC ID cannot be used on the final product. In these circumstances, the OEM integrator will be responsible for re-evaluating the end product (including the transmitter) and obtaining a separate FCC authorization.

© 2023 Doodle Labs. All rights reserved. Preliminary Datasheet 1 Doodle Labs Mini OEM Mesh Rider Radio - 915MHz and 2.4GHz Overview The Mini OEM Mesh Rider Radio is an advanced Manet router. The Mini OEM Mesh Rider Radio employs Doodle Labs' patented Mesh Rider® technology with state-of-the-art RF and networking capabilities that enable communication further, faster, and more reliably than any comparable solution on the market. For example, optimized video streaming carries crystal clear 4K video while simultaneously carrying low latency Command and Control data. The interoperable Mesh Rider Radio platform is available in many frequency bands between 600 MHz and 6 GHz in Mini, Nano, OEM, Wearable form factors. This flexibility allows customers to use their industry speciíc frequency bands for deploying private wireless networks that encompasses all the use cases for human and machine collaboration. For more information, please visit: https://doodlelabs.com/mesh-rider-radios/ © 2023 Doodle Labs. All rights reserved. Preliminary Datasheet 2 Key Features - Mesh Rider Radio Platform PERFORMANCE RF  Long range (field tested >100km) and high throughput (up to 100 Mbps) Mesh Rider waveform  Interference resistant COFDM for robust link quality in difficult RF environments  Exceptional Multipath and NrLOS performance  Adaptive radio modulations from BPSK up to 64QAM, with fast per packet optimization to maximize link performance in dynamic environments  Software defined channel bandwidth for effïcient re-use of spectrum  Convolutional coding, Forward Error Correction (FEC), ACK-retransmits, Maximal Ratio Combining, Spatial Multiplexing, and Space Time Block Coding for robust data transmission over noisy channel/spectrum  Single channel, Time Division Duplexing (TDD) for bi-directional traffïc Resistant to high-power jamming signals  ATPC for widely dispersed mesh network  Built-in Spectrum Scanner to help mitigate interference issues PERFORMANCE NETWORKING  Ultra-Reliable Low Latency Channel (URLLC) for Command and Control  Optimized video streaming channel for Unicast and Multicast transport  Self-healing/self-forming multifrequency mobile mesh for highly reliable network with redundancy  FIPS Certiíed AES 256- and 128-bit encryption  End-to-end IP architecture with Ad Hoc, WDS transparent bridge, Client, AP, and Internet Gateway operating modes  Embedded network management APIs ADDITIONAL FEATURES  Very small size, weight, and power for mobile applications  Ethernet, USB, and UART interfaces to allow easy integration into different system architectures  Leverage the beneíts of the most extensible OpenWrt ecosystem and install 3rd party IoT applications  Rugged, vibration resistant construction to meet MIL-specs  MIL-spec temp range (-40C to +85C)  High quality, manufactured in ISO 9001 and ISO 14001 certifíed facilities  COTS – Commercial oì the Shelf  Extended lifespan and availability © 2023 Doodle Labs. All rights reserved. Preliminary Datasheet 3 System Integration  The Mesh Rider Radio has been designed to be plug and play. Only USB and a power supply are required for integration. Visit Doodle Labs Technical Library for extensive design-in documents. © 2023 Doodle Labs. All rights reserved. Preliminary Datasheet 4 Technical Specifications (915MHz and 2450MHz Bands) Model Category Xtreme ORDERING CODES Radio Configuration 1x1 SISO Model # RM-1700-21N3 Antenna (Optional) ANT-1700-3-O Evaluation Kit EK-1700: 1x Multi-band Antenna, Breakout board, Cables Design-In Documentation Doodle Labs Technical Library PERFORMANCE OVERVIEW Max Operating Range (Indicative) >20 Km (Recommended), (Max field demonstrated range >100km) Max Data Throughput at 10-meter range with specified Antennas (Indicative) 80 Mbps (20 MHz Channel) 40 Mbps (10 MHz Channel) 20Mbps (5MHz Channel) Over the Air Data Encryption 128-bit AES (Full throughput) 256-bit AES (12 Mbps max throughput) (FIPS140-3)(optional) Operating Modes Mesh, WDS AP, WDS Client Bridged or Internet Gateway with NAT Command & Control channel Ultra-Reliable Low Latency Channel (URLLC). Latency 1.5 - 15 ms Video Channel Optimized video streaming with Unicast and Multicast transmission © 2023 Doodle Labs. All rights reserved. Preliminary Datasheet 5 Model Category Xtreme RF SPECIFICATIONS Protocol Compatibility Fully compatible with Doodle Labs Mesh Rider Waveform Frequency Range 915-MHz and 2450-MHz Bands Operating Bands (Software Selectable) 902-928 MHz 2400-2482 MHz Advanced Band Filters Dedicated SAW filters for high interference immunity Channel Sizes (Software Selectable) 915MHz Band: 5MHz/ 10MHz 2.4GHz Band: 10MHz/ 20MHz Radio Data Rate Auto adapting Modulation Coding Scheme (MCS0-15) RF Power Output (Typ) Each radio individually calibrated 1W (30 dBm) Antenna Signal Strength -30 to -90 dBm (Recommended), Absolute Maximum= +12 dBm Receiver LNA Gain >10 dB RF Power Control In 1dB steps, Tolerance +/-1dB Integrated Antenna Port Protection Able to withstand open port, >10 KV (contact) and >15KV (open air discharge) as per IEC-61000-4-2 Wireless Error Correction FEC, ARQ Transmitter Spurious Emission Suppression < - 40 dBc Frequency Accuracy ±10 ppm max over life Automatic Transmit Power Control (ATPC) Intelligently adjusts the transmit power for very close range operation NETWORKING SPECIFICATIONS Mesh Router Self-Forming/Self-Healing, Peer to Peer Custom Software Package Manager Image Builder, OPKG, ipk Radio Management Web GUI (HTTPs), SSH and JSON-RPC Access control Password, MAC, IP, Port filtering Supported Protocols IPv6, QoS, DNS, HTTPS, IP, ICMP, NTP, DHCP © 2023 Doodle Labs. All rights reserved. Preliminary Datasheet 6 Model Category Xtreme Software Upgrade Over the air software upgrade supported HARDWARE SPECIFICATIONS Operating Voltage 5V +/- 5% DC DC Power Consumption 915-MHz: Average 4W (50% Tx/Rx duty cycle), 6W Peak Tx power @ max range, 2.7W Rx mode 2450-MHz: Average 3W (50% Tx/Rx duty cycle), 4.5W Peak Tx power @…

Text truncated - open the document above for the full version.

Covered Equipment Identification Letter For Certification Service in the USA Federal Communication Commission Equipment Authorization Division, Application Processing Branch 7435 Oakland Mills Road Columbia, MD 21048 To whom it may concern Pursuant to Section 2.911(d)(5)(ii) of the Commission’s Rules (47 C.F.R.) we attest as follows: We, applicant Company Name: Doodle Labs (SG) Pte Ltd Address: 601 MacPherson Road, Grantral Complex, Suite 07-15 Singapore 368242, Singapore Phone: +65-6253 0100 certify that, as of the date of the filing of the application, the applicant is not identified on the Covered List as an entity producing “covered” equipment. If you have any questions, please feel free to contact us at the address shown below. Sincerely, Signature Date:2024-03-11 Name / Title: Sanjay Malani / Product Engineering Manager Company: Doodle Labs (SG) Pte Ltd Address: 601 MacPherson Road, Grantral Complex, Suite 07-15 Singapore 368242, Singapore Phone: +65-6253 0100 Fax: +65-6353 5564 E-Mail: [email protected]

Confidentiality Request Letter For Certification Service in the USA Federal Communication Commission Equipment Authorization Division, Application Processing Branch 7435 Oakland Mills Road Columbia, MD 21048 To whom it may concern Pursuant to Paragraphs §0.457 and 0.459 of the Commission’s Rules (47 C.F.R.) and Section §552(b)(4) of the Freedom of Information Act, we request confidentiality for the documentation of the following products: FCC ID Model name 2AG87RM1700-1N RM-1700-21N3, RM-1700-21N, RM-1700-21N3-IN, RM-1700-21N4, RM-1700-21N4-IN For the products listed above, we request permanent confidentiality for all applicable exhibits as there are:  the Operational Description  the Block Diagram  the Schematics The above listed exhibits contain trade secrets and proprietary information that could be of benefit to our competitors. If you have any questions, please feel free to contact us at the address shown below. Sincerely, Signature Date:2024-03-11 Name / Title: Sanjay Malani / Product Engineering Manager Company: Doodle Labs (SG) Pte Ltd Address: 601 MacPherson Road, Grantral Complex, Suite 07-15 Singapore 368242, Singapore Phone: +65-6253 0100 Fax: +65-6353 5564 E-Mail: [email protected]

Modular Approval Request Letter Federal Communications Commission Equipment Authorization Division, Application Processing Branch 7435 Oakland Mills Road Columbia, MD 21048 Modular Approval Request We, <Doodle Labs (SG) Pte Ltd>, declare on our sole responsibility and in accordance with CFR 47 Part 15.212 the following for our module identified as follows: Product Information PMN: Mesh Rider Radio FVIN: n/a HMN: n/a ISED Certification Number: n/a HVIN: n/a Model Name: RM-1700-21N3, RM- 1700-21N, RM-1700- 21N3-IN, RM-1700-21N4, RM-1700-21N4-IN FCC ID: 2AG87RM1700-1N Declaration Modular approval requirement Yes No * (a) The radio elements must have the radio frequency circuitry shielded. Physical/discrete and tuning capacitors may be located external to the shield, but must be on the module assembly. Yes *Please provide a detailed explanation if the answer is “No.”: (b) The module shall have buffered modulation/data input(s) (if such inputs are provided) to ensure that the module will comply with the requirements set out in the applicable RSS / part 15 under conditions of excessive data rates or over-modulation. Yes *Please provide a detailed explanation if the answer is “No.”: (c) The module shall have its own power supply regulation on the module. This is to ensure that the module will comply with the requirements set out in the applicable standard regardless of the design of the power supplying circuitry in the host device which houses the module. Yes *Please provide a detailed explanation if the answer is “No.”: (d) The module shall comply with the provisions for external power amplifiers and antennas detailed in this standard. The equipment certification submission shall contain a detailed description of the configuration of highest antenna gain for each type of antenna. Yes *Please provide a detailed explanation if the answer is “No.”: (e) The module shall be tested for compliance with the applicable standard in a stand- alone configuration, i.e. the module must not be inside another device during testing. Yes *Please provide a detailed explanation if the answer is “No.”: (f) The module shall comply with applicable RSS-102 exposure requirements and any applicable FCC RF exposure requirement which are based on the intended configuration/integration in a host. Yes *Please provide a detailed explanation if the answer is “No.”: Only applicable for FCC certification: (g) The module must be equipped with either a permanently affixed label or must be capable of electronically displaying its FCC identification number. Yes *Please provide a detailed explanation if the answer is “No.”: (h) The modular transmitter complies with all applicable FCC rules. Instructions for maintaining compliance are given in the user instructions. Yes Please do not hesitate to contact us for further explanations or comments. Sincerely, Signature Date:2024-03-11 Name / Title: Sanjay Malani / Product Engineering Manager Company: Doodle Labs (SG) Pte Ltd Address: 601 MacPherson Road, Grantral Complex, Suite 07-15 Singapore 368242, Singapore Phone: +65-6253 0100 Fax: +65-6353 5564 E-Mail: [email protected]

Page 1 of 7 FCC ID: 2AG87RM1700-1N Shenzhen LCS Compliance Testing Laboratory Ltd. Add: 101, 201 Bldg A & 301 Bldg C, Juji Industrial Park Yabianxueziwei, Shajing Street, Baoan District, Shenzhen, 518000, China Tel: +(86) 0755-82591330 | E-mail: [email protected] | Web: www.lcs-cert.com Scan code to check authenticity External Photos of the EUT Model: RM-1700-21N3, RM-1700-21N, RM-1700-21N3-IN Fig. 1 Page 2 of 7 FCC ID: 2AG87RM1700-1N Shenzhen LCS Compliance Testing Laboratory Ltd. Add: 101, 201 Bldg A & 301 Bldg C, Juji Industrial Park Yabianxueziwei, Shajing Street, Baoan District, Shenzhen, 518000, China Tel: +(86) 0755-82591330 | E-mail: [email protected] | Web: www.lcs-cert.com Scan code to check authenticity Fig. 2 Fig. 3 Fig. 4 2.4G antenna 915 antenna Page 3 of 7 FCC ID: 2AG87RM1700-1N Shenzhen LCS Compliance Testing Laboratory Ltd. Add: 101, 201 Bldg A & 301 Bldg C, Juji Industrial Park Yabianxueziwei, Shajing Street, Baoan District, Shenzhen, 518000, China Tel: +(86) 0755-82591330 | E-mail: [email protected] | Web: www.lcs-cert.com Scan code to check authenticity Fig. 5 Fig. 6 Page 4 of 7 FCC ID: 2AG87RM1700-1N Shenzhen LCS Compliance Testing Laboratory Ltd. Add: 101, 201 Bldg A & 301 Bldg C, Juji Industrial Park Yabianxueziwei, Shajing Street, Baoan District, Shenzhen, 518000, China Tel: +(86) 0755-82591330 | E-mail: [email protected] | Web: www.lcs-cert.com Scan code to check authenticity Fig. 7 Fig. 8 Page 5 of 7 FCC ID: 2AG87RM1700-1N Shenzhen LCS Compliance Testing Laboratory Ltd. Add: 101, 201 Bldg A & 301 Bldg C, Juji Industrial Park Yabianxueziwei, Shajing Street, Baoan District, Shenzhen, 518000, China Tel: +(86) 0755-82591330 | E-mail: [email protected] | Web: www.lcs-cert.com Scan code to check authenticity Fig. 9 Fig. 10 Page 6 of 7 FCC ID: 2AG87RM1700-1N Shenzhen LCS Compliance Testing Laboratory Ltd. Add: 101, 201 Bldg A & 301 Bldg C, Juji Industrial Park Yabianxueziwei, Shajing Street, Baoan District, Shenzhen, 518000, China Tel: +(86) 0755-82591330 | E-mail: [email protected] | Web: www.lcs-cert.com Scan code to check authenticity Fig. 11 RM-1700-21N4, RM-1700-21N4-IN (For Reference) Fig. 12 Page 7 of 7 FCC ID: 2AG87RM1700-1N Shenzhen LCS Compliance Testing Laboratory Ltd. Add: 101, 201 Bldg A & 301 Bldg C, Juji Industrial Park Yabianxueziwei, Shajing Street, Baoan District, Shenzhen, 518000, China Tel: +(86) 0755-82591330 | E-mail: [email protected] | Web: www.lcs-cert.com Scan code to check authenticity Fig. 13

Page 1 of 1 FCC ID: 2AG87RM1700-1N Shenzhen LCS Compliance Testing Laboratory Ltd. Add: 101, 201 Bldg A & 301 Bldg C, Juji Industrial Park Yabianxueziwei, Shajing Street, Baoan District, Shenzhen, 518000, China Tel: +(86) 0755-82591330 | E-mail: [email protected] | Web: www.lcs-cert.com Scan code to check authenticity LABEL AND LOCATION (Size: L: 3.0cm x W: 0.7cm) Label Location Mesh Rider Radio Model: RM-1700-21N3 FCC ID: 2AG87RM1700-1N

Page 1 of 13 FCC ID: 2AG87RM1700-1N Shenzhen LCS Compliance Testing Laboratory Ltd. Add: 101, 201 Bldg A & 301 Bldg C, Juji Industrial Park Yabianxueziwei, Shajing Street, Baoan District, Shenzhen, 518000, China Tel: +(86) 0755-82591330 | E-mail: [email protected] | Web: www.lcs-cert.com Scan code to check authenticity Internal Photos of the EUT Model: RM-1700-21N3, RM-1700-21N, RM-1700-21N3-IN Fig. 1 Fig. 2 Page 2 of 13 FCC ID: 2AG87RM1700-1N Shenzhen LCS Compliance Testing Laboratory Ltd. Add: 101, 201 Bldg A & 301 Bldg C, Juji Industrial Park Yabianxueziwei, Shajing Street, Baoan District, Shenzhen, 518000, China Tel: +(86) 0755-82591330 | E-mail: [email protected] | Web: www.lcs-cert.com Scan code to check authenticity Fig. 3 Fig. 4 Page 3 of 13 FCC ID: 2AG87RM1700-1N Shenzhen LCS Compliance Testing Laboratory Ltd. Add: 101, 201 Bldg A & 301 Bldg C, Juji Industrial Park Yabianxueziwei, Shajing Street, Baoan District, Shenzhen, 518000, China Tel: +(86) 0755-82591330 | E-mail: [email protected] | Web: www.lcs-cert.com Scan code to check authenticity Fig. 5 Fig. 6 Page 4 of 13 FCC ID: 2AG87RM1700-1N Shenzhen LCS Compliance Testing Laboratory Ltd. Add: 101, 201 Bldg A & 301 Bldg C, Juji Industrial Park Yabianxueziwei, Shajing Street, Baoan District, Shenzhen, 518000, China Tel: +(86) 0755-82591330 | E-mail: [email protected] | Web: www.lcs-cert.com Scan code to check authenticity Fig. 7 Fig. 8 Page 5 of 13 FCC ID: 2AG87RM1700-1N Shenzhen LCS Compliance Testing Laboratory Ltd. Add: 101, 201 Bldg A & 301 Bldg C, Juji Industrial Park Yabianxueziwei, Shajing Street, Baoan District, Shenzhen, 518000, China Tel: +(86) 0755-82591330 | E-mail: [email protected] | Web: www.lcs-cert.com Scan code to check authenticity Fig. 9 Fig. 10 Page 6 of 13 FCC ID: 2AG87RM1700-1N Shenzhen LCS Compliance Testing Laboratory Ltd. Add: 101, 201 Bldg A & 301 Bldg C, Juji Industrial Park Yabianxueziwei, Shajing Street, Baoan District, Shenzhen, 518000, China Tel: +(86) 0755-82591330 | E-mail: [email protected] | Web: www.lcs-cert.com Scan code to check authenticity Fig. 11 Page 7 of 13 FCC ID: 2AG87RM1700-1N Shenzhen LCS Compliance Testing Laboratory Ltd. Add: 101, 201 Bldg A & 301 Bldg C, Juji Industrial Park Yabianxueziwei, Shajing Street, Baoan District, Shenzhen, 518000, China Tel: +(86) 0755-82591330 | E-mail: [email protected] | Web: www.lcs-cert.com Scan code to check authenticity Model: RM-1700-21N4, RM-1700-21N4-IN (For Reference) Fig. 12 Page 8 of 13 FCC ID: 2AG87RM1700-1N Shenzhen LCS Compliance Testing Laboratory Ltd. Add: 101, 201 Bldg A & 301 Bldg C, Juji Industrial Park Yabianxueziwei, Shajing Street, Baoan District, Shenzhen, 518000, China Tel: +(86) 0755-82591330 | E-mail: [email protected] | Web: www.lcs-cert.com Scan code to check authenticity Fig. 13 Fig. 14 Page 9 of 13 FCC ID: 2AG87RM1700-1N Shenzhen LCS Compliance Testing Laboratory Ltd. Add: 101, 201 Bldg A & 301 Bldg C, Juji Industrial Park Yabianxueziwei, Shajing Street, Baoan District, Shenzhen, 518000, China Tel: +(86) 0755-82591330 | E-mail: [email protected] | Web: www.lcs-cert.com Scan code to check authenticity Fig. 15 Fig. 16 Page 10 of 13 FCC ID: 2AG87RM1700-1N Shenzhen LCS Compliance Testing Laboratory Ltd. Add: 101, 201 Bldg A & 301 Bldg C, Juji Industrial Park Yabianxueziwei, Shajing Street, Baoan District, Shenzhen, 518000, China Tel: +(86) 0755-82591330 | E-mail: [email protected] | Web: www.lcs-cert.com Scan code to check authenticity Fig. 17 Fig. 18 Page 11 of 13 FCC ID: 2AG87RM1700-1N Shenzhen LCS Compliance Testing Laboratory Ltd. Add: 101, 201 Bldg A & 301 Bldg C, Juji Industrial Park Yabianxueziwei, Shajing Street, Baoan District, Shenzhen, 518000, China Tel: +(86) 0755-82591330 | E-mail: [email protected] | Web: www.lcs-cert.com Scan code to check authenticity Fig. 19 Page 12 of 13 FCC ID: 2AG87RM1700-1N Shenzhen LCS Compliance Testing Laboratory Ltd. Add: 101, 201 Bldg A & 301 Bldg C, Juji Industrial Park Yabianxueziwei, Shajing Street, Baoan District, Shenzhen, 518000, China Tel: +(86) 0755-82591330 | E-mail: [email protected] | Web: www.lcs-cert.com Scan code to check authenticity Fig. 20 Fig. 21 Page 13 of 13 FCC ID: 2AG87RM1700-1N Shenzhen LCS Compliance Testing Laboratory Ltd. Add: 101, 201 Bldg A & 301 Bldg C, Juji Industrial Park Yabianxueziwei, Shajing Street, Baoan District, Shenzhen, 518000, China Tel: +(86) 0755-82591330 | E-mail: [email protected] | Web: www.lcs-cert.com Scan code to check authenticity Fig. 22 Fig. 23

Page 1 of 4 FCC ID: 2AG87RM1700-1N Shenzhen LCS Compliance Testing Laboratory Ltd. Add: 101, 201 Bldg A & 301 Bldg C, Juji Industrial Park Yabianxueziwei, Shajing Street, Baoan District, Shenzhen, 518000, China Tel: +(86) 0755-82591330 | E-mail: [email protected] | Web: www.lcs-cert.com Scan code to check authenticity FCC RF Exposure Evaluation 1. Product Information FCC ID 2AG87RM1700-1N Product name Mesh Rider Radio Model number RM-1700-21N3 Additional Model No. RM-1700-21N RM-1700-21N3-IN RM-1700-21N4 RM-1700-21N4-IN Power supply Input: DC 5V, 3A 915MHz Frequency Range 902MHz~928MHz Channel Spacing 1MHz Channel Number 17 Channels for 10MHz bandwidth (907~923MHz) 21 Channels for 5MHz bandwidth (905~925MHz) Modulation Type g mode: OFDM (64QAM, 16QAM, QPSK, BPSK) n mode: OFDM (64…

Text truncated - open the document above for the full version.