2AH78-AKEPLERWKepler Wi-Fi and Bluetooth

AINA Kepler Wi-Fi QUICK GUIDE AINA Wireless DOC ID : IU0014 ver. 1.7. INCLUDED IN THE PACKAGE X 1 X 1 BUTTONS AND CONNECTIONS C. Emergency K. Power D. PTT 1 E. Speaker F. PTT 2 G. Up arrow/ Volume up H. Left arrow A. Display L. Headset jack and micro-USB charging N. Right arrow O. Down arrow/ Volume down X 1 B. LED indicator I. Belt clip J. Microphone M. Docking station charging contacts BUTTON FUNCTIONS ICONS Press until the greed LED turns off to turn the device on or off. While the device is off and charging, pressing the button will show the battery level. When the device is on, it will open or close the device’s menu. Press for 3 seconds to activate or cancel an emergency call. During operation, the up and down arrow buttons are for volume control. While the device is on the menu screen, the up and down arrow can be used for selection. During operation, pressing the left or right arrow will change the talk group. While the device is on the menu screen, the left and right arrow can be used for selection. Battery status. When there is an exclamation mark (!) above the icon, the battery is in critical level. If the exclamation mark appears while charging the device, this means that the device has stopped charging to avoid over-heating. Charging will resume automatically once it is safe to do so. Wi-Fi network strength. Connected to the service. Disconnected from the service. Headphones connected. CHARGING THE BATTERY 1 2 3 4 EN 1. Connect the provided USB cable to the device and wall charger. 2. The display will show the battery level for 10 seconds. 3. Wait until the device is fully charged. 4. Disconnect the USB cable. NOTE! Recommended wall charger rating: 2A. 2 REPLACING THE BATTERY 1 2 3 EN 1. Turn off the device and open battery cover with the provided screwdriver. 2. Remove the device’s battery and make sure the inside of the device is clear of any dust and dirt, specially the grey area shown above, to ensure the watertightness of the device. 3. Insert the replacement battery into the device so that the battery contacts align and the battery label faces into the device. Then slide the battery cover back into place and screw it shut. Do not over tighten. NOTE! The screwdriver head size is TX6. POWER ON / OFF ON OFF EN Turn on by pressing the Power button until the green LED turns off. Turn off by pressing the Power button until the AINA logo appears on the display. NOTE! Pressing the Power button for longer than 7 seconds, will restart the device. This should only be used if the device is unresponsive. CONNECTING TO THE WI-FI EN 1. After turning on the device, press the Power button to access the Menu. 2. Go to Settings and then Wi-Fi. 3. Input the SSID and confirm this by holding the right arrow button down. 4 Select whether you have a PSK (yes or no). 5. If yes, input the PSK and confirm this by holding the right arrow button down. 6. Your device will reboot automatically. DATE & TIME SETTINGS EN 1. After turning on the device, press the Power button to access the Menu. 2. Go to Date & Time and then Timezone. 3. Select and confirm the correct timezone. 4. Your device will reboot automatically. EN For best result hold the device 15-20cm from your mouth when speaking. MICROPHONE PERFORMANCE TIP 1. Do not put the device near your ear, SPL > 100dBA. 2. Avoid contact with magnetic stripe cards. 3. Charging temperature: 0°C - + 45°C. 4. Operation temperature: -10°C - + 60°C. 5. Bluetooth Operating frequency range: 2.4 - 2.4835 GHz. 6. Bluetooth power level: Class 1 (8dBm). 7. Wi-Fi Operating frequency range: 2.412-2.484 GHz, 4.9-5.975 GHz. 8. Wi-Fi power level: 2GHz Band, 18dB, 5GHz Band 13.5dBm. Frequency Output power ISM 2.4GHz 20dBm NFC 13.56MHz - SAFETY For more detailed instructions on setting up and using your Kepler, please refer to the User Manual, available online at www.ainaptt.com If any part of the equipment is damaged on arrival, contact the shipper to conduct an inspection and prepare a damage report. Save the shipping container and all packing materials until the inspection and the damage report are completed. In addition, contact the Customer Care to make arrangements for replacement equipment. Do not return any part of the shipment until you receive detailed instructions from an AINA Wireless representative. Product warranty information can be found from: www.ainaptt.com/terms-and-conditions Contact Customer Care at: Phone Number: + 358 40 322 6717 E-mail: [email protected] OPERATION CUSTOMER CARE LEGAL GUIDELINES AINA Wireless Inc. (AINA Wireless Finland Oy) is continuously evaluating technical publications that have been produced for completeness and technical accuracy. You can assist us in this process by submitting your comments and suggestions to the following address: AINA Wireless Finland Oy Joensuunkatu 7G 24100 Salo Finland Or email us to [email protected] The software contained in this device is copyrighted by AINA Wireless. Unpublished rights are reserved under the copyright laws of the United States. AINA TM is a registered trademark and is of AINA Wireless Inc. The N-Mark is a trademark or registered trademark of NFC Forum, Inc. in the United States and in other countries Bluetooth® is a registered trademark of Bluetooth SIG, Inc. Apple®, iTunes®, iPhone®, and iPad® are registered trademarks of Apple Inc. iOS™ is a trademark or registered trademark of Cisco in the U.S. and other countries and is used under license. ACKNOWLEDGEMENTS CREDITS Google® is a registered trademark of Google Inc. Android™, Google Maps™, Google Earth™, Google Play™, and Gmail™ are trademarks of Google Inc. BC-mark is registered trademark of California Energy Commission. All brand and product names are trademarks, registered trademarks, or service marks of their respective holders. The material contained herein is subject to U.S. export approval. No export or re-export is permitted without written approval from the U.S. Government. Rated: EAR99 in accordance with U.S. Dept. of Co…

Text truncated - open the document above for the full version.

A I N A W I R E L E S S F I N L A ND O Y Salo IoT Campus, Joensuunkatu 7G 24100 Salo, Finland www.ainaptt.com • +358 40 322 6717 • [email protected] VAT-ID: FI23956662 Declaration of Authorization We Name: AINA Wireless Finland Oy Address: Joensuunkatu 7G City: 24100 Salo Country: Finland Declare that: Name Representative of agent: Adyl Mssalak Agent Company name: 7layers GmbH (Bureau Veritas Group) Address: Borsigstrasse 11 City: 40880 Ratingen Country Germany is authorized to apply for Certification of the following product(s): Product description: Kepler Wi-Fi Type designation: AKEPLER-0010-01 Trademark: AINA Validity/ expiry date 31.01.2023 on our behalf. Date: 13.07.2022 City: Salo Name: Tony Vahtera Function: Operations Signature:

A I N A W I R E L E S S F I N L A ND O Y Salo IoT Campus, Joensuunkatu 7G 24100 Salo, Finland www.ainaptt.com • +358 40 322 6717 • [email protected] VAT-ID: FI23956662 Declaration of Authorization We Name: AINA Wireless Finland Oy Address: Joensuunkatu 7G City: 24100 Salo Country: Finland Declare that: Name Representative of agent: Adyl Mssalak Agent Company name: 7layers GmbH (Bureau Veritas Group) Address: Borsigstrasse 11 City: 40880 Ratingen Country Germany is authorized to apply for Certification of the following product(s): Product description: Kepler Wi-Fi Type designation: AKEPLER-0010-01 Trademark: AINA Validity/ expiry date 31.01.2023 on our behalf. Date: 13.07.2022 City: Salo Name: Tony Vahtera Function: Operations Signature:

FCC, Request for non-disclosure Date: 21-Nov-2018 RF_501, Issue 8 Page 1 of 1 Company Name: AINA Wireless Finland Oy Address : Joensuunkatu 7G City: 24100 Salo Country: Finland To: Telefication B.V., Dept. FCC TCB Edisonstraat 12A 6902 PK ZEVENAAR The Netherlands Subject: Request for confidentiality FCC ID: 2AH78-AKEPLERW Reference number: ###### Dear FCC TCB, 1. Long-Term Confidentiality Pursuant to 47 CFR Section 0.459(a) & (b), we hereby requests non-disclosure and confidential treatment of the following materials submitted in support of FCC certification application: Bill(s) of Material Block Diagrams Operational Description Schematic Diagrams Tune-up Procedure Above materials contain secrets, proprietary and technical information, which would customarily be guarded from competitors under 47 CFR, section 0.457(d)(2). Disclosure or publication or any portion of this company confidential material to other parties could cause substantial competitive harm and provide unjustified benefits for competitors. 2. Short-Term Confidentiality (STC) Pursuant to Public Notice DA 04-1705 of the Commission’s policy, in order to comply with the marketing regulations in 47 CFR §2.803 and the importation rules in 47 CFR §2.1204, a pplicant hereby requests Short-Term Confidential treatment of the following materials (See notes below): Internal Photos User’s Manual Test Set-up Photos External Photos Justification: Date: 28-10-2022 Name and signature of applicant: Adyl Mssalak Notes: 1) A document or type of document can only have ONE type of confidentiality! 2) Short-Term confidentiality is in principle for 45 days from date of grant; it can be extended max 3 times (total time 180 days max.)! The planned date should stated in the RF731 application form. 3) FCC must be informed when marketing begins earlier. 4) Release takes place automatically thus extension must be requested in time. Telefication does not remind you of this! 5) Request for extension or for release must be received by Telefication at least 7 days before date of actual marketing or before expiration of the STC period

A I N A W I R E L E S S F I N L A ND O Y Salo IoT Campus, Joensuunkatu 7G 24100 Salo, Finland www.ainaptt.com • +358 40 322 6717 • [email protected] VAT-ID: FI23956662 A I N A W I R E L E S S F I N L A ND O Y Salo IoT Campus, Joensuunkatu 7G 24100 Salo, Finland www.ainaptt.com • +358 40 322 6717 • [email protected] VAT-ID: FI23956662 A I N A W I R E L E S S F I N L A ND O Y Salo IoT Campus, Joensuunkatu 7G 24100 Salo, Finland www.ainaptt.com • +358 40 322 6717 • [email protected] VAT-ID: FI23956662

Ver 0.2 Page 129 November 2021 Lasering template, AKEPLER, Wi-Fi MADE IN ESTONIA MADE IN ESTONIA AINA Wireless Finland Oy, Joensuunkatu 7G, 24100 Salo, Finland Font sizes:Arial 4pt Tahoma 4pt Arial 3.5pt Contains FCC ID:RFR-BL871 IC: 21419-AKEPLERW ICES-003 Pn: AKEPLER-0010-01 Sn: AW720510013 AINA KEPLER Wlan Wlan MAC: 867698040350244 BT 0 MAC: 867698040350244 BT 1 MAC: 867698040350244 AINA Wireless Finland Oy, Joensuunkatu 7G, 24100 Salo, Finland IC: 21419-AKEPLERW ICES-003 Pn: AKEPLER-0010-01 Sn: AW7MMYYxxxx AINA KEPLER Wi-Fi Wi-Fi MAC: 867698040350244 BT 0 MAC: 867698040350244 BT 1 MAC: 867698040350244 Contains FCC ID:XF6-M7DB7 FCC ID: 2AH78-AKEPLERW Contains FCC ID:XF6-M7DB7 FCC ID: 2AH78-AKEPLERW Contains FCC ID:RFR-BL871 Ver 0.2 Page 229 November 2021 Label template unit box, AKEPLER, Wi-Fi Pn: AKEPLER-0001-01 Sn: AW619460013 MADE IN ESTONIA RoHs Kepler For manuals and support please visit w w w . a i n a-w i r e l e s s . c o m Wi-Fi Pn: AKEPLER-0001-00 Sn: AW619460013 MADE IN ESTONIA RoHs Kepler For manuals and support please visit w w w . a i n a-w i r e l e s s . c o m BT Ver 0.2 Page 329 November 2021 Label template X box, AKEPLER, Wi-Fi Kepler For manuals and support please visit w w w . a i n a-w i r e l e s s . c o m Wi-Fi MADE IN ESTONIA 10 pack Sn: KPPG2820001 RoHs Sn: AW619460012 Sn: AW619460013 Sn: AW619460014 Sn: AW619460015 Sn: AW619460016 Sn: AW619460017 Sn: AW619460019 Sn: AW619460020 Sn: AW619460010 Sn: AW619460011 10 pcs Pn: AKEPLER-0001-01 Kepler For manuals and support please visit w w w . a i n a-w i r e l e s s . c o m BT MADE IN ESTONIA 10 pack Sn: KPG2820001 RoHs Sn: AW619460012 Sn: AW619460013 Sn: AW619460014 Sn: AW619460015 Sn: AW619460016 Sn: AW619460017 Sn: AW619460019 Sn: AW619460020 Sn: AW619460010 Sn: AW619460011 10 pcs Pn: AKEPLER-0001-01 Ver 0.2 Page 429 November 2021 Label template X box, AKEPLER, Wi-Fi Kepler For manuals and support please visit w w w . a i n a-w i r e l e s s . c o m Wi-Fi MADE IN ESTONIA 100 pack Sn: KP1PG2820001 RoHs 10 pack Sn: KPPG2820002 10 pack Sn: KPPG2820003 10 pack Sn: KPPG2820004 10 pack Sn: KPPG2820005 10 pack Sn: KPPG2820006 10 pack Sn: KPPG2820007 10 pack Sn: KPPG2820008 10 pack Sn: KPPG2820009 10 pack Sn: KPPG2820000 10 pack Sn: KPPG2820001 100 pcs Pn: AKEPLER-0001-01 Kepler For manuals and support please visit w w w . a i n a-w i r e l e s s . c o m BT MADE IN ESTONIA 100 pack Sn: KP1G2820001 RoHs 10 pack Sn: KPG2820002 10 pack Sn: KPG2820003 10 pack Sn: KPG2820004 10 pack Sn: KPG2820005 10 pack Sn: KPG2820006 10 pack Sn: KPG2820007 10 pack Sn: KPG2820008 10 pack Sn: KPG2820009 10 pack Sn: KPG2820000 10 pack Sn: KPG2820001 100 pcs Pn: AKEPLER-0001-01

A I N A W I R E L E S S F I N L A ND O Y Salo IoT Campus, Joensuunkatu 7G 24100 Salo, Finland www.ainaptt.com • +358 40 322 6717 • [email protected] VAT-ID: FI23956662 A I N A W I R E L E S S F I N L A ND O Y Salo IoT Campus, Joensuunkatu 7G 24100 Salo, Finland www.ainaptt.com • +358 40 322 6717 • [email protected] VAT-ID: FI23956662 A I N A W I R E L E S S F I N L A ND O Y Salo IoT Campus, Joensuunkatu 7G 24100 Salo, Finland www.ainaptt.com • +358 40 322 6717 • [email protected] VAT-ID: FI23956662 A I N A W I R E L E S S F I N L A ND O Y Salo IoT Campus, Joensuunkatu 7G 24100 Salo, Finland www.ainaptt.com • +358 40 322 6717 • [email protected] VAT-ID: FI23956662

1 (54) Copyright © Verkotan Document ID:FCC_ISED SAR report AINA KEPLER WiFi ID5710 11102022 SAR Compliance Test Report Date of Report 31/10/2022 Client’s Contact person: Tony Vahtera Number of pages: 54 Responsible Test engineer: Jesper Varis Testing laboratory: Verkotan Oy Elektroniikkatie 17 90590 Oulu Finland Client: AINA Wireless Finland Oy Joensuunkatu 7G 24100 Salo Finland Tested device Aina Kepler, Wi-Fi Related reports: - Testing has been carried out in accordance with: 47CFR §2.1093 Radiofrequency Radiation Exposure Evaluation: Portable Devices FCC published RF exposure KDB procedures RSS-102 Radio Frequency (RF) Exposure Compliance of Radiocommunication Apparatus (All Frequency Bands) Documentation: The test report must always be reproduced in full; reproduction of an excerpt only is subject to written approval of the testing laboratory Test Results: The EUT complies with the requirements in respect of all parameters subject to the test. The test results relate only to devices specified in this document Date and signatures: 31.10.2022 For the contents: Laboratory Manager 2 (54) Copyright © Verkotan Document ID:FCC_ISED SAR report AINA KEPLER WiFi ID5710 11102022 TABLE OF CONTENTS 1. SUMMARY OF SAR TEST REPORT ............................................................................................................................ 3 1.1 TEST DETAILS ..................................................................................................................................................... 3 1.2 MAXIMUM RESULTS .......................................................................................................................................... 3 1.2.1 Simultaneous Transmission SAR .................................................................................................................. 4 1.2.2 Maximum Drift .............................................................................................................................................. 4 1.2.3 Measurement Uncertainty ............................................................................................................................. 4 2. DESCRIPTION OF THE DEVICE UNDER TEST (DUT) ................................................................................................ 5 2.1 SUPPORTED FREQUENCY BANDS AND OPERATIONAL MODES ......................................................................... 5 2.2 SIMULTANEOUS TRANSMISSION....................................................................................................................... 6 2.3 TEST EXCLUSIONS .............................................................................................................................................. 6 2.3.1 FCC ................................................................................................................................................................ 6 2.3.2 ISED ............................................................................................................................................................... 7 3. OUTPUT POWER ....................................................................................................................................................... 8 3.1 MAXIMUM OUTPUT POWER .............................................................................................................................. 8 3.2 TESTED CONDUCTED POWER ............................................................................................................................ 9 4. TEST EQUIPMENT.................................................................................................................................................... 10 4.1 TEST EQUIPMENT LIST ..................................................................................................................................... 11 4.1.1 Isotropic E-field Probe Type EX3DV4 ........................................................................................................... 11 4.2 PHANTOMS ..................................................................................................................................................... 12 4.2.1 SAM Phantom .............................................................................................................................................. 12 4.2.2 ELI Phantom ................................................................................................................................................. 12 4.3 TISSUE SIMULANTS .......................................................................................................................................... 12 4.4 SYSTEM VALIDATION STATUS.......................................................................................................................... 12 4.5 SYSTEM CHECK ................................................................................................................................................ 13 4.5.1 Tissue Simulant Verification ......................................................................................................................... 13 5. TEST PROCEDURE ................................................................................................................................................... 14 5.1 TEST POSITIONS .............................................................................................................................................. 14 5.2 SCAN PROCEDURES ......................................................................................................................................... 14 5.3 SAR AVERAGING METHODS ............................................................................................................................ 14 6. MEASUREMENT UNCERTAINTY ....................................................................................................................…

Text truncated - open the document above for the full version.

Test Laboratory: 7layers GmbH Borsigstrasse 11 40880 Ratingen Germany Note: The following test results relate only to the devices specified in this document. This report shall not be reproduced in parts without the written approval of the test laboratory. 7layers GmbH Geschäftsführer/ Borsigstraße 11 Managing Directors: Registergericht/registered: a Bureau Veritas 40880 Ratingen, Germany Frank Spiller Düsseldorf HRB 75554 Group Company T +49 (0) 2102 749 0 Bernhard Retka USt-Id.-Nr./VAT-No. DE203159652 F +49 (0) 2102 749 350 Alexandre Norré-Oudard Steuer-Nr./TAX-No. 147/5869/0385 www.7layers.com Commerzbank AG Account No. 303 016 000 Bank Code 300 400 00 IBAN DE81 3004 0000 0303 0160 00 Swift Code COBADEFF FCC Measurement/Technical Report on Kepler Wi-Fi FCC ID: 2AH78-AKEPLERW IC: 21419-AKEPLERW Simultaneous Transmissions report Test Report Reference: MDE_AINA_2002_FCC_01 TEST REPORT REFERENCE: MDE_AINA_2002_FCC_01 Page 2 of 32 Table of Contents 1 Applied Standards and Test Summary 3 1.1 Applied Standards 3 1.2 FCC-IC Correlation Table 4 1.3 Measurement Summary 5 2 Revision History / Signatures 6 3 Administrative Data 7 3.1 Testing Laboratory 7 3.2 Project Data 7 3.3 Applicant Data 7 3.4 Manufacturer Data 8 4 Test object Data 9 4.1 General EUT Description 9 4.2 EUT Main components 10 4.3 Ancillary Equipment 10 4.4 Auxiliary Equipment 11 4.5 EUT Setups 11 4.6 Operating Modes / Test Channels 11 4.7 Product labelling 11 5 Test Results 12 5.1 TRANSMITTER SPURIOUS RADIATED EMISSIONS 12 5.2 Undesirable Emissions; General Field Strength Limits 18 6 Test Equipment 24 7 Antenna Factors, Cable Loss and Sample Calculations 25 7.1 LISN R&S ESH3-Z5 (150 kHz – 30 MHz) 25 7.2 Antenna R&S HFH2-Z2 (9 kHz – 30 MHz) 26 7.3 Antenna R&S HL562 (30 MHz – 1 GHz) 27 7.4 Antenna R&S HF907 (1 GHz – 18 GHz) 28 7.5 Antenna EMCO 3160-09 (18 GHz – 26.5 GHz) 29 7.6 Antenna EMCO 3160-10 (26.5 GHz – 40 GHz) 30 8 Measurement Uncertainties 31 9 Photo Report 32 TEST REPORT REFERENCE: MDE_AINA_2002_FCC_01 Page 3 of 32 1 APPLIED STANDARDS AND TEST SUMMARY 1.1 APPLIED STANDARDS Type of Authorization Certification for an Intentional Radiator (Digital Device / Spread Spectrum). Applicable FCC Rules Prepared in accordance with the requirements of FCC Rules and Regulations as listed in 47 CFR Ch.1 Parts 2 (10-1-20 Edition) and 15 (10-1-19 Edition). The following subparts are applicable to the results in this test report. Part 2, Subpart J - Equipment Authorization Procedures, Certification Part 15, Subpart C – Intentional Radiators § 15.201 Equipment authorization requirement § 15.207 Conducted limits § 15.209 Radiated emission limits; general requirements § 15.247 Operation within the bands 902-928 MHz, 2400-2483.5 MHz Part 15, Subpart E – Unlicensed National Information Infrastructure Devices § 15.403 Definitions § 15.407 General technical requirements ANSI C63.10-2013 is applied. TEST REPORT REFERENCE: MDE_AINA_2002_FCC_01 Page 4 of 32 1.2 FCC-IC CORRELATION TABLE Correlation of measurement requirements from FCC and IC UNII equipment Measurement FCC reference IC reference Transmitter undesirable emissions; General Field Strength Limits, Restricted Bands § 15.407 (b) § 15.209 (a) RSS-Gen Issue 5: 6.13/8.9/8.10; RSS-247 Issue 2: 3.3/6.2 6.2.1.2, 6.2.2.2, 6.2.3.2, 6.2.4.2 Transmitter spurious radiated emissions § 15.247 (d); § 15.209 (a) RSS-Gen Issue 5: 6.13 / 8.9/8.10; RSS-247 Issue 2: 5.5 TEST REPORT REFERENCE: MDE_AINA_2002_FCC_01 Page 5 of 32 1.3 MEASUREMENT SUMMARY 47 CFR CHAPTER I FCC PART 15 Subpart E §15.407 FCC §15.407 (b), (1),(2),(3),(4); FCC §15.205, §15.209, §15.407 (b) (5),(6) Undesirable Emissions; General Field Strength Limits The measurement was performed according to ANSI C63.10 Final Result OP-Mode Radio Technology, Operating Frequency; Measurement range Setup Date FCC IC Proprietary 2.4 GHz Radio, Ch. 20 (2470 MHz) + WLAN a 6 Mbit, Ch124 5620 MHz, 1GHz - 26GHz S01_AC01 2022-07-21 Passed Passed 47 CFR CHAPTER I FCC PART 15 Subpart C §15.247 § 15.247 (d) Transmitter Spurious Radiated Emissions The measurement was performed according to ANSI C63.10 Final Result OP-Mode Radio Technology, Operating Frequency; Measurement range Setup Date FCC IC Proprietary 2.4 GHz Radio, Ch. 1 (2413 MHz) + WLAN b 20 MHz, Ch. 6 (2440 MHz); 1 GHz - 26 GHz S01_AE01 2022-07- 21 Passed Passed Proprietary 2.4 GHz Radio, Ch. 20 (2470 MHz) + WLAN a 20 MHz, Ch. 116 (5580 MHz); 1 GHz - 26 GHz S01_AE01 2022-07- 21 Passed Passed Proprietary 2.4 GHz Radio, Ch. 20 (2470 MHz) + Bluetooth Classic DH5 Ch. 0 (2402 MHz); 1 GHz - 26 GHz S01_AE01 2022-07- 28 Passed Passed N/A: Not applicable N/P: Not performed TEST REPORT REFERENCE: MDE_AINA_2002_FCC_01 Page 7 of 32 3 ADMINISTRATIVE DATA 3.1 TESTING LABORATORY Company Name: 7layers GmbH Address: Borsigstr. 11 40880 Ratingen Germany The test facility is accredited by the following accreditation organisation: Laboratory accreditation no: DAkkS D-PL-12140-01-01| -02 | -03 FCC Designation Number: DE0015 FCC Test Firm Registration: 929146 ISED CAB Identifier DE0007; ISED#: 3699A Responsible for accreditation scope: Daniel Gall Report Template Version: 2020-06-15 3.2 PROJECT DATA Responsible for testing and report: Mohamed Fraitat Employees who performed the tests: documented internally at 7Layers Date of Report: 2022-08-30 Testing Period: 2022-07-21 to 2022-07-28 3.3 APPLICANT DATA Company Name: AINA Wireless Finland Oy Address: Joensuunkatu 7G 24100 Salo Finland Contact Person: Tony Vahtara TEST REPORT REFERENCE: MDE_AINA_2002_FCC_01 Page 8 of 32 3.4 MANUFACTURER DATA Company Name: Please see applicant data TEST REPORT REFERENCE: MDE_AINA_2002_FCC_01 Page 9 of 32 4 TEST OBJECT DATA 4.1 GENERAL EUT DESCRIPTION Kind of Device product description The EUT is a WLAN and BT enabled handheld PTT device with a DMO as an backup communication. The EUT is using additionally to Bluetooth and Wifi a proprietary 2.4 GHz radio for handling communication between devices. Product name Kepler Wi-Fi Type AKEPLER-0010-01 Decl…

Text truncated - open the document above for the full version.

Test Laboratory: 7layers GmbH Borsigstrasse 11 40880 Ratingen Germany Note: The following test results relate only to the devices specified in this document. This report shall not be reproduced in parts without the written approval of the test laboratory. 7layers GmbH Geschäftsführer/ Borsigstraße 11 Managing Directors: Registergericht/registered: a Bureau Veritas 40880 Ratingen, Germany Sebastian Doose Düsseldorf HRB 75554 Group Company T +49 (0) 2102 749 0 Stefan Kischka USt-Id.-Nr./VAT-No. DE203159652 F +49 (0) 2102 749 350 Bernhard Retka Steuer-Nr./TAX-No. 147/5869/0385 www.7layers.com Commerzbank AG Account No. 303 016 000 Bank Code 300 400 00 IBAN DE81 3004 0000 0303 0160 00 Swift Code COBADEFF FCC Measurement/Technical Report on Kepler Wi-Fi FCC ID: 2AH78-AKEPLERW IC: 21419-AKEPLERW Test Report Reference: MDE_AINA_2002_FCC_03 TEST REPORT REFERENCE: MDE_AINA_2002_FCC_03 Page 2 of 66 Table of Contents 1 Applied Standards and Test Summary 3 1.1 Applied Standards 3 1.2 FCC-IC Correlation Table 4 1.3 Measurement Summary 5 2 Revision History / Signatures 8 3 Administrative Data 9 3.1 Testing Laboratory 9 3.2 Project Data 9 3.3 Applicant Data 9 3.4 Manufacturer Data 9 4 Test object Data 10 4.1 General EUT Description 10 4.2 EUT Main components 10 4.3 Ancillary Equipment 11 4.4 Auxiliary Equipment 11 4.5 EUT Setups 11 4.6 Operating Modes / Test Channels 11 4.7 Product labelling 12 5 Test Results 13 5.1 Conducted Emissions at AC Mains 13 5.2 Occupied Bandwidth (20 dB) 16 5.3 Occupied Bandwidth (99%) 20 5.4 Peak Power Output 23 5.5 Spurious RF Conducted Emissions 27 5.6 Transmitter Spurious Radiated Emissions 31 5.7 Band Edge Compliance Conducted 39 5.8 Band Edge Compliance Radiated 44 5.9 Channel Separation 48 5.10 Number of Hopping Frequencies 51 6 Test Equipment 55 7 Antenna Factors, Cable Loss and Sample Calculations 59 7.1 LISN R&S ESH3-Z5 (150 kHz – 30 MHz) 59 7.2 Antenna R&S HFH2-Z2 (9 kHz – 30 MHz) 60 7.3 Antenna R&S HL562 (30 MHz – 1 GHz) 61 7.4 Antenna R&S HF907 (1 GHz – 18 GHz) 62 7.5 Antenna EMCO 3160-09 (18 GHz – 26.5 GHz) 63 7.6 Antenna EMCO 3160-10 (26.5 GHz – 40 GHz) 64 8 Measurement Uncertainties 65 9 Photo Report 66 TEST REPORT REFERENCE: MDE_AINA_2002_FCC_03 Page 3 of 66 1 APPLIED STANDARDS AND TEST SUMMARY 1.1 APPLIED STANDARDS Type of Authorization Certification for an Intentional Radiator. Applicable FCC Rules Prepared in accordance with the requirements of FCC Rules and Regulations as listed in 47 CFR Ch.1 Parts 2 and 15 (10-1-20 Edition). The following subparts are applicable to the results in this test report. Part 2, Subpart J - Equipment Authorization Procedures, Certification Part 15, Subpart C – Intentional Radiators § 15.201 Equipment authorization requirement § 15.207 Conducted limits § 15.209 Radiated emission limits; general requirements § 15.247 Operation within the bands 902-928 MHz, 2400-2483.5 MHz Note: The tests were selected and performed with reference to the FCC Public Notice “Guidance for Compliance Measurements on Digital Transmission System, Frequency Hopping Spread Spectrum System, and Hybrid System Devices Operating under Section 15.247 of the FCC Rules, 558074 D01 15.247 Meas Guidance v05r02, 2019-04-02”. ANSI C63.10–2013 is applied. TEST REPORT REFERENCE: MDE_AINA_2002_FCC_03 Page 4 of 66 1.2 FCC-IC CORRELATION TABLE Correlation of measurement requirements for FHSS (e.g. Bluetooth ® ) equipment from FCC and IC FHSS equipment Measurement FCC reference IC reference Conducted emissions on AC Mains § 15.207 RSS-Gen Issue 5: 8.8 Occupied bandwidth § 15.247 (a) (1) RSS-247 Issue 2: 5.1 (b) Peak conducted output power § 15.247 (b) (1), (4) RSS-247 Issue 2: 5.4 (b) Transmitter spurious RF conducted emissions § 15.247 (d) RSS-Gen Issue 5: 6.13/8.9/8.10; RSS-247 Issue 2: 5.5 Transmitter spurious radiated emissions § 15.247 (d); § 15.209 (a) RSS-Gen Issue 5: 6.13 / 8.9/8.10; RSS-247 Issue 2: 5.5 Band edge compliance § 15.247 (d) RSS-247 Issue 2: 5.5 Dwell time § 15.247 (a) (1) (iii) RSS-247 Issue 2: 5.1 (d) Channel separation § 15.247 (a) (1) RSS-247 Issue 2: 5.1 (b) No. of hopping frequencies § 15.247 (a) (1) (iii) RSS-247 Issue 2: 5.1 (d) Hybrid systems (only) § 15.247 (f); § 15.247 (e) RSS-247 Issue 2: 5.3 Antenna requirement § 15.203 / 15.204 RSS-Gen Issue 5: 8.3 Receiver spurious emissions – - TEST REPORT REFERENCE: MDE_AINA_2002_FCC_03 Page 5 of 66 1.3 MEASUREMENT SUMMARY 47 CFR CHAPTER I FCC PART 15 Subpart C §15.247 § 15.207 Conducted Emissions at AC Mains The measurement was performed according to ANSI C63.10 6.2 Final Result OP-Mode Op…

Text truncated - open the document above for the full version.