2AIV6-S200Intelligent Two Way Radio

GSM,WCDMA,LTE,GPS 3.8V 0 warning Any Changes or modifications not expressly approved by the party responsible for compliance could void the user's authority to operate the equipment. This device complies with part 15 of the FCC Rules. Operation is subject to the following two conditions: (1) This device may not cause harmful interference, and (2) this device must accept any interference received, including interference that may cause undesired operation. Note: This equipment has been tested and found to comply with the limits for a Class B digital device, pursuant to part 15 of the FCC Rules. These limits are designed to provide reasonable protection against harmful interference in a residential installation. This equipment generates, uses and can radiate radio frequency energy and, if not installed and used in accordance with the instructions, may cause harmful interference to radio communications. However, there is no guarantee that interference will not occur in a particular installation. If this equipment does cause harmful interference to radio or television reception, which can be determined by turning the equipment off and on, the user is encouraged to try to correct the interference by one or more of the following measures: —Reorient or relocate the receiving antenna. —Increase the separation between the equipment and receiver. —Connect the equipment into an outlet on a circuit different from that to which the receiver is connected. —Consult the dealer or an experienced radio/TV technician for help. For face-up,10mm was used for test, this equipment should be installed and operated with minimum distance 10mm. SAR tests are conducted using standard operating positions accepted by the FCC with the device transmitting at its highest certified power level in all tested frequency bands, although the SAR is determined at the highest certified power level, the actual SAR level of the device while operating can be well below the maximum value. Before a new model device is a available for sale to the public, it must be tested and certified to the FCC that it does not exceed the exposure limit established by the FCC, Tests for each device are performed in positions and locations ( worn on the body)as required by the FCC. Non-compliance with the above restrictions may result in violation of RF exposure guidelines. For body worn operation, this model phone has been tested and meets the FCC RF exposure guidelines when used with an accessory designated for this product or when used with an accessory that Contains no metal and that positions the handset a minimum of 0 cm from the body.

Shenzhen Inrico Electronics Co.,Ltd ADD: 3/F, Building NO.118, High Tech Industrial Park, 72 Guowei Road, Luohu District, Shenzhen China TEL: 0755-83273589 FAX: 0755-82689912 E-mail: [email protected] FCC Authorization Date: 2020-06-20 FEDERAL COMMUNICATIONS COMMISSION Authorization and Evaluation Division 7435 Oakland Mills Road Columbia, MD 21046 Subject: Agent Authorization To whom it may concern: We , Shenzhen Inrico Electronics Co.,Ltd , Hereby authorizes Bay Area Compliance Laboratories Corporation to act on its behalf in all matters relating to application for Equipment authorization, including the signing of all documents relating to these matters. All acts carried out by Bay Area Compliance Laboratory Corporation on our behalf shall have the same effect as our own action. We, the undersigned, hereby certify that we are not subject to a denial of federal benefits, that includes FCC benefits, pursuant to Section 5301 of the Anti-Drug Abuse Act of 1988, 21 U.S.C. 862. This authorization is valid until further written notice from the applicant. Sincerely Yours, Client’s signature Printed Name: Wenshun Zhang Title: Manager QA-FR-170-B

QA -FR-171-A Shen zhen Inrico Electronics Co.,Ltd ADD: 3/F, Building NO.118, High Tech Industrial Park, 72 Guowei Road, Luohu District, Shenzhen China TEL:0755-83273589 FAX: 0755-82689912 E-mail:[email protected] FCC Conf idential Authorization Date : 2020-06-20 FEDERAL COMMUNICATIONS COMMISSIONS Authorization and Evaluation Division 7435 Oakland Mills Road Columbia, MD 21046 Subject: Confidentiality Request regarding application for certification of FCC ID:2AIV6-S200 In accordance with Sections 0.457 and 0.459 of the Commission’s Rules, Shenzhen Inrico Electronics Co.,Ltd hereby requests long-term confidential treatment of information accompanying this application as outlined below:  Block Diagram  Schematics  Operation Description  Parts List/Tune up procedure T he above materials contain proprietary and confidential information not customarily released to the public. The public disclosure of these materials provides unjustified benefits to its competitors in the market. Sincerely, Signature: Printed Name: Wenshun Zhang Title: Manager

EXHIBIT B - EUT EXTERNAL PHOTOGRAPHS

FCC ID:2AIV6-S200

EXHIBIT C - EUT INTERNAL PHOTOGRAPHS Antenna Battery Label

Note: This test report is prepared for the customer shown above and for the device described herein. It may not be duplicated or used in part without prior written consent from Bay Area Compliance Laboratories Corp. (Dongguan). This report must not be used by the customer to claim product certification, approval, or endorsement by A2LA* or any agency of the Federal Government. * This report may contain data that are not covered by the A2LA accreditation and are marked with an asterisk “*”. SAR EVALUATION REPORT For Shenzhen Inrico Electronics Co.,Ltd 3/F, Building No.118, High Tech Industrial Park, 72 Guowei Road, Luohu District, Shenzhen China FCC ID: 2AIV6-S200 Report Type: Original Report Product Type: Intelligent Two Way Radio Report Number: RDG200511002-20 Report Date: 2020-06-18 Reviewed By: Rocky Xiao RF Engineer Prepared By: Bay Area Compliance Laboratories Corp. (Dongguan) No.69 Pulongcun, Puxinhu Industry Area, Tangxia, Dongguan, Guangdong, China Tel: +86-769-86858888 Fax: +86-769-86858891 www.baclcorp.com.cn Bay Area Compliance Laboratories Corp. (Dongguan) Report No.: RDG200511002-20 SAR Evaluation Report 2 of 58 Attestation of Test Results EUT Information EUT Description Intelligent Two Way Radio Tested Model S200 FCC ID 2AIV6-S200 Serial Number RDG200511002-SA-S1 Test Date 2020-5-12~ 2020-5-13 MODE Max. SAR Level(s) Reported(W/kg) Limit (W/kg) GSM 850 1g Head SAR(Face Up) 0.56 1.6 1g Body SAR(Body Back) 0.98 PCS 1900 1g Head SAR(Face Up) 0.17 1g Body SAR(Body Back) 0.53 WCDMA Band 2 1g Head SAR(Face Up) 0.29 1g Body SAR(Body Back) 0.45 WCDMA Band 5 1g Head SAR(Face Up) 0.30 1g Body SAR(Body Back) 0.41 LTE Band 2 1g Head SAR(Face Up) 0.45 1g Body SAR(Body Back) 0.59 LTE Band 4 1g Head SAR(Face Up) 0.56 1g Body SAR(Body Back) 0.36 LTE Band 5 1g Head SAR(Face Up) 0.42 1g Body SAR(Body Back) 0.57 LTE Band 12&17 1g Head SAR(Face Up) 0.22 1g Body SAR(Body Back) 0.37 LTE Band 13 1g Head SAR(Face Up) 0.18 1g Body SAR(Body Back) 0.41 Applicable Standards FCC 47 CFR part 2.1093 Radiofrequency radiation exposure evaluation: portable devices RF Exposure Procedures: TCB Workshop April 2019 IEEE1528:2013 IEEE Recommended Practice for Determining the Peak Spatial-Average Specific Absorption Rate (SAR) in the Human Head from Wireless Communications Devices: Measurement Techniques IEC 62209-1:2016 Measurement procedure for the assessment of specific absorption rate of human exposure to radio frequency fields from hand-held and body-mounted wireless communication devices – Part 1: Devices used next to the ear (Frequency range of 300 MHz to 6 GHz) KDB procedures KDB 447498 D01 General RF Exposure Guidance v06 KDB 648474 D04 Handset SAR v01r03 KDB 865664 D01 SAR Measurement 100 MHz to 6 GHz v01r04 KDB 865664 D02 RF Exposure Reporting v01r02 KDB 941225 D01 3G SAR Procedures v03r01 KDB 941225 D05 SAR for LTE Devices v02r05 Note: This wireless device has been shown to be capable of compliance for localized specific absorption rate (SAR) for General Population/Uncontrolled Exposure limits specified in FCC 47 CFR part 2.1093 and has been tested in accordance with the measurement procedures specified in IEEE 1528-2013 and RF exposure KDB procedures. The results and statements contained in this report pertain only to the device(s) evaluated. Bay Area Compliance Laboratories Corp. (Dongguan) Report No.: RDG200511002-20 SAR Evaluation Report 3 of 58 TABLE OF CONTENTS DOCUMENT REVISION HISTORY ......................................................................................................................... 4 EUT DESCRIPTION .................................................................................................................................................... 5 TECHNICAL SPECIFICATION ......................................................................................................................................... 5 REFERENCE, STANDARDS, AND GUIDELINES .................................................................................................. 6 SAR LIMITS ................................................................................................................................................................. 7 FACILITIES .................................................................................................................................................................. 8 DESCRIPTION OF TEST SYSTEM .......................................................................................................................... 9 EQUIPMENT LIST AND CALIBRATION ............................................................................................................. 15 EQUIPMENTS LIST & CALIBRATION INFORMATION .................................................................................................... 15 SAR MEASUREMENT SYSTEM VERIFICATION .............................................................................................. 16 LIQUID VERIFICATION ............................................................................................................................................... 16 SYSTEM ACCURACY VERIFICATION ........................................................................................................................... 18 SAR SYSTEM VALIDATION DATA ..................................................................................................................... 19 EUT TEST STRATEGY AND METHODOLOGY ................................................................................................. 22 TEST POSITIONS FOR DEVICE OPERATING NEXT TO A PERSON’S EAR........................................................................ 22 CHEEK/TOUCH POSITION ........................................................................................................................................... 23 EAR/TILT POSITION .....................................................................................................................…

Text truncated - open the document above for the full version.

PROBE CALIBRATION CERTIFICATES DIPOLE CALIBRATION CERTIFICATES

Report No.: RDG200511002-20 Page 1 of 30 Test Plot 1#: GSM 850_Face Up_Mid DUT: Intelligent Two Way Radio; Type: S200; Serial: RDG200511002-SA-S1 Communication System: Generic GSM; Frequency: 836.6 MHz;Duty Cycle: 1:8 Medium parameters used: f = 836.6 MHz; σ = 0.915 S/m; ε r = 40.799; ρ = 1000 kg/m 3 Phantom section: Flat Section DASY5 Configuration:  Probe: EX3DV4 - SN7329; ConvF(9.97, 9.97, 9.97) @ 836.6 MHz; Calibrated: 2019/10/22  Sensor-Surface: 1.4mm (Mechanical Surface Detection)  Electronics: DAE4 Sn772; Calibrated: 2019/10/6  Phantom: SAM (30deg probe tilt) with CRP v5.0_20150321; Type: QD000P40CD; Serial: TP:1874  Measurement SW: DASY52, Version 52.10 (2); SEMCAD X Version 14.6.12 (7470) Area Scan (61x131x1): Interpolated grid: dx=1.500 mm, dy=1.500 mm Maximum value of SAR (interpolated) = 0.663 W/kg Zoom Scan (5x5x7)/Cube 0: Measurement grid: dx=8mm, dy=8mm, dz=5mm Reference Value = 24.28 V/m; Power Drift = -0.01 dB Peak SAR (extrapolated) = 0.747 W/kg SAR(1 g) = 0.529 W/kg; SAR(10 g) = 0.381 W/kg Maximum value of SAR (measured) = 0.659 W/kg 0 dB = 0.659 W/kg = -1.81 dBW/kg Report No.: RDG200511002-20 Page 2 of 30 Test Plot 2#: GSM 850_Body Back_Low DUT: Intelligent Two Way Radio; Type: S200; Serial: RDG200511002-SA-S1 Communication System: Generic GPRS-4 slots; Frequency: 824.2 MHz;Duty Cycle: 1:2 Medium parameters used: f = 824.2 MHz; σ = 0.895 S/m; ε r = 41.012; ρ = 1000 kg/m 3 Phantom section: Flat Section DASY5 Configuration:  Probe: EX3DV4 - SN7329; ConvF(9.97, 9.97, 9.97) @ 824.2 MHz; Calibrated: 2019/10/22  Sensor-Surface: 1.4mm (Mechanical Surface Detection)  Electronics: DAE4 Sn772; Calibrated: 2019/10/6  Phantom: SAM (30deg probe tilt) with CRP v5.0_20150321; Type: QD000P40CD; Serial: TP:1874  Measurement SW: DASY52, Version 52.10 (2); SEMCAD X Version 14.6.12 (7470) Area Scan (61x131x1): Interpolated grid: dx=1.500 mm, dy=1.500 mm Maximum value of SAR (interpolated) = 1.11 W/kg Zoom Scan (5x5x7)/Cube 0: Measurement grid: dx=8mm, dy=8mm, dz=5mm Reference Value = 32.28 V/m; Power Drift = 0.01 dB Peak SAR (extrapolated) = 1.22 W/kg SAR(1 g) = 0.895 W/kg; SAR(10 g) = 0.654 W/kg Maximum value of SAR (measured) = 1.11 W/kg 0 dB = 1.11 W/kg = 0.45 dBW/kg Report No.: RDG200511002-20 Page 3 of 30 Test Plot 3#: GSM 850_Body Back_Mid DUT: Intelligent Two Way Radio; Type: S200; Serial: RDG200511002-SA-S1 Communication System: Generic GPRS-4 slots; Frequency: 836.6 MHz;Duty Cycle: 1:2 Medium parameters used: f = 836.6 MHz; σ = 0.915 S/m; ε r = 40.799; ρ = 1000 kg/m 3 Phantom section: Flat Section DASY5 Configuration:  Probe: EX3DV4 - SN7329; ConvF(9.97, 9.97, 9.97) @ 836.6 MHz; Calibrated: 2019/10/22  Sensor-Surface: 1.4mm (Mechanical Surface Detection)  Electronics: DAE4 Sn772; Calibrated: 2019/10/6  Phantom: SAM (30deg probe tilt) with CRP v5.0_20150321; Type: QD000P40CD; Serial: TP:1874  Measurement SW: DASY52, Version 52.10 (2); SEMCAD X Version 14.6.12 (7470) Area Scan (61x131x1): Interpolated grid: dx=1.500 mm, dy=1.500 mm Maximum value of SAR (interpolated) = 1.12 W/kg Zoom Scan (5x5x7)/Cube 0: Measurement grid: dx=8mm, dy=8mm, dz=5mm Reference Value = 33.65 V/m; Power Drift = -0.18 dB Peak SAR (extrapolated) = 1.22 W/kg SAR(1 g) = 0.893 W/kg; SAR(10 g) = 0.650 W/kg Maximum value of SAR (measured) = 1.11 W/kg 0 dB = 1.11 W/kg = 0.45 dBW/kg Report No.: RDG200511002-20 Page 4 of 30 Test Plot 4#: GSM 850_Body Back_High DUT: Intelligent Two Way Radio; Type: S200; Serial: RDG200511002-SA-S1 Communication System: Generic GPRS-4 slots; Frequency: 848.8 MHz;Duty Cycle: 1:2 Medium parameters used: f = 848.8 MHz; σ = 0.928 S/m; ε r = 40.278; ρ = 1000 kg/m 3 Phantom section: Flat Section DASY5 Configuration:  Probe: EX3DV4 - SN7329; ConvF(9.97, 9.97, 9.97) @ 848.8 MHz; Calibrated: 2019/10/22  Sensor-Surface: 1.4mm (Mechanical Surface Detection)  Electronics: DAE4 Sn772; Calibrated: 2019/10/6  Phantom: SAM (30deg probe tilt) with CRP v5.0_20150321; Type: QD000P40CD; Serial: TP:1874  Measurement SW: DASY52, Version 52.10 (2); SEMCAD X Version 14.6.12 (7470) Area Scan (61x131x1): Interpolated grid: dx=1.500 mm, dy=1.500 mm Maximum value of SAR (interpolated) = 1.05 W/kg Zoom Scan (5x5x7)/Cube 0: Measurement grid: dx=8mm, dy=8mm, dz=5mm Reference Value = 31.05 V/m; Power Drift = -0.05 dB Peak SAR (extrapolated) = 1.14 W/kg SAR(1 g) = 0.841 W/kg; SAR(10 g) = 0.611 W/kg Maximum value of SAR (measured) = 1.04 W/kg 0 dB = 1.04 W/kg = 0.17 dBW/kg Report No.: RDG200511002-20 Page 5 of 30 Test Plot 5#: PCS 1900_Face Up_Mid DUT: Intelligent Two Way Radio; Type: S200; Serial: RDG200511002-SA-S1 Communication System: Generic GSM; Frequency: 1880 MHz;Duty Cycle: 1:8 Medium parameters used: f = 1880 MHz; σ = 1.393 S/m; ε r = 39.096; ρ = 1000 kg/m 3 Phantom section: Flat Section DASY5 Configuration:  Probe: EX3DV4 - SN7329; ConvF(8.29, 8.29, 8.29) @ 1880 MHz; Calibrated: 2019/10/22  Sensor-Surface: 1.4mm (Mechanical Surface Detection)  Electronics: DAE4 Sn772; Calibrated: 2019/10/6  Phantom: SAM (30deg probe tilt) with CRP v5.0_20150321; Type: QD000P40CD; Serial: TP:1874  Measurement SW: DASY52, Version 52.10 (2); SEMCAD X Version 14.6.12 (7470) Area Scan (61x131x1): Interpolated grid: dx=1.500 mm, dy=1.500 mm Maximum value of SAR (interpolated) = 0.258 W/kg Zoom Scan (5x5x7)/Cube 0: Measurement grid: dx=8mm, dy=8mm, dz=5mm Reference Value = 5.892 V/m; Power Drift = -0.05 dB Peak SAR (extrapolated) = 0.314 W/kg SAR(1 g) = 0.172 W/kg; SAR(10 g) = 0.101 W/kg Maximum value of SAR (measured) = 0.259 W/kg 0 dB = 0.259 W/kg = -5.87 dBW/kg Report No.: RDG200511002-20 Page 6 of 30 Test Plot 6#: PCS 1900_Body Back_Mid DUT: Intelligent Two Way Radio; Type: S200; Serial: RDG200511002-SA-S1 Communication System: Generic GPRS-4 slots; Frequency: 1880 MHz;Duty Cycle: 1:2 Medium parameters used: f = 1880 MHz; σ = 1.393 S/m; ε r = 39.096; ρ = 1000 kg/m 3 Phantom section: Flat Section DASY5 Configuration:  Probe: EX3DV4 - SN7329; ConvF(8.29, 8.29, 8.29) @ 1880 MHz; Calibrated: 2019/10/22 …

Text truncated - open the document above for the full version.

Report No.: RDG200511002-20 Page 1 of 2 APPENDIX B EUT TEST POSITION PHOTOS Liquid depth ≥ 15cm Phantom: SAM (30deg probe tilt) with CRP v5.0_20150321; Type: QD000P40CD; Serial: TP:1874 Report No.: RDG200511002-20 Page 2 of 2 Body Back Setup Photo (0mm) Head Face Up Setup Photo (10mm) 10 mm

FCC PART 22H, PART 24E,PART 27 MEASUREMENT AND TEST REPORT For Shenzhen Inrico Electronics Co.,Ltd 3/F, Building No.118, High Tech Industrial Park, 72 Guowei Road, Luohu District, Shenzhen Chian Report Type: Original Report Product Type: Intelligent Two Way Radio Report Number: RDG200511002-00A Report Date: 2020-06-09 Reviewed B y: Ivan Cao Assistant manager Test Laboratory: Bay Area Compliance Laboratories Corp. (Dongguan) No.69 Pulongcun, Puxinhu Industry Area, Tangxia, Dongguan, Guangdong, China Tel: +86-769-86858888 Fax: +86-769-86858891 www.baclcorp.com.cn FCC ID:2AIV6-S200 Bay Area Compliance Laboratories Corp. (Dongguan) Report No.: RDG200511002-00A Page 2 of 171 TABLE OF CONTENTS GENERAL INFORMATION ....................................................................................................................................... 4 PRODUCT DESCRIPTION FOR EQUIPMENT UNDER TEST (EUT) ..................................................................................... 4 OBJECTIVE ................................................................................................................................................................... 4 RELATED SUBMITTAL(S)/GRANT(S) ............................................................................................................................. 4 TEST METHODOLOGY .................................................................................................................................................. 4 MEASUREMENT UNCERTAINTY .................................................................................................................................... 5 TEST FACILITY ............................................................................................................................................................. 5 DECLARATIONS ............................................................................................................................................................ 5 SYSTEM TEST CONFIGURATION .......................................................................................................................... 6 JUSTIFICATION ............................................................................................................................................................. 6 EQUIPMENT MODIFICATIONS ....................................................................................................................................... 7 SUPPORT EQUIPMENT LIST AND DETAILS .................................................................................................................... 7 CONFIGURATION OF TEST SETUP ................................................................................................................................. 7 BLOCK DIAGRAM OF TEST SETUP ................................................................................................................................ 7 SUMMARY OF TEST RESULTS ............................................................................................................................... 8 FCC §1.1310 , §2.1093 - RF EXPOSURE ....................................................................................................................... 9 APPLICABLE STANDARD .............................................................................................................................................. 9 TEST RESULT ............................................................................................................................................................... 9 FCC §2.1047 - MODULATION CHARACTERISTIC ............................................................................................ 10 FCC § 2.1046, § 22.913 (A) & § 24.232 (C) & § 27.50 - RF OUTPUT POWER ..................................................... 11 APPLICABLE STANDARD ............................................................................................................................................ 11 TEST PROCEDURE ...................................................................................................................................................... 12 TEST EQUIPMENT LIST AND DETAILS ......................................................................................................................... 17 TEST DATA ................................................................................................................................................................ 17 FCC §2.1049, §22.917, §22.905 & §24.238 & §27.53- OCCUPIED BANDWIDTH ............................................... 34 APPLICABLE STANDARD ............................................................................................................................................ 34 TEST PROCEDURE ...................................................................................................................................................... 34 TEST EQUIPMENT LIST AND DETAILS ......................................................................................................................... 34 TEST DATA ................................................................................................................................................................ 34 FCC §2.1051, §22.917(A) & §24.238(A) & §27.53- SPURIOUS EMISSIONS AT ANTENNA TERMINALS ... 66 APPLICABLE STANDARD ............................................................................................................................................ 66 TEST PROCEDURE ...................................................................................................................................................... 66 TEST EQUIPMENT LIST AND DETAILS ......................................................................................................................... 66 TEST DATA .....................................................................................…

Text truncated - open the document above for the full version.