2AJGM-888STWO-WAY RADIO

Two Way Radio MODEL: BF-888S USER‘S MANUAL IMPORTANT NOTICE WARNINGS: Replacement or substitution of transistors, regular diodes or other parts of a unique nature, with parts other than those recommended by PO FUNG COMPANY may cause a violation of the technical regulations of part 95 of the FCC rules, or violation of type acceptance requirements of part 2 of the rules. Your radio is set up to transmit a regulated signal on an assigned frequency. Any adjustment to your radio must be made by qualified technicians. This device complies with Part 15 of the FCC Rules. Operation is subject to the following two conditions: 1) This device may not cause harmful interference, and 2) this device must accept any interference received, including interference that may cause undesired operation. FCC & RSS WARNINGS: Any Changes or modifications not expressly approved by the party responsible for compliance could void the user’s authority to operate the equipment. SAR tests are conducted using standard operating positions accepted by the FCC/ISEDC with the device transmitting at its highest certified power level in all tested frequency bands, although the SAR is determined at the highest certified power level, the actual SAR level of the device while operating can be well below the maximum value. Before a new model is a available for sale to the public, it must be tested and certified to the FCC/ISEDC that it does not exceed the exposure limit established by the FCC/ISEDC Tests for each product are performed in positions and locations as required by the FCC/ISEDC. For body worn operation, this device has been tested and meets the FCC/ISEDC RF exposure guidelines when used with an accessory designated for this product or when used with and accessory that contains no metal. Tm maintain compliance with the FCC/ISEDC’s RF exposure guidelines, hold the transmitter and antenna at least 1 inch(2.5 centimeters) from your face and speak in a normal voice, with the antenna pointed up and away from the face. This equipment complies with FCC/ISEDC radiation exposure limits set forth for an uncontrolled environment. In order to comply with the FCC/ISEDC RF exposure requirements, the antenna installation must comply with following: Users must be fully aware of the hazards of the exposure and able to exercise control over their RF exposure to qualify for the higher exposure limits. Your wireless hand-held portable transceiver contains a low power transmitter. This product sends out radio frequency (RF) signals when the Push-to-Talk (PTT) Button is pressed. The device is authorized to operate at a duty factor not to exceed 50%. This device complies with ISEDC licence-exempt RSS standard (s). Operation is subject to the following two conditions: (1) this device may not cause interference, and (2) this device must accept any interference, including interference that may cause undesired operation of the device. Le présent areil est conforme aux CNR d’ISEDC licables aux arels radio exemprs de licence. L’exploitation est autorisée aux deux conditions suivantes: (1) I’areil ne doit pas produire de brouillage,et (2) I’utilisateru de I’appareil doit accepter tout brouillage radioélectrique subi, même si le brouillage est susceptible d’en compromettre le fonctionnement. ISEDC expositon aux radiations Cet équipement est conforme avec ISEDC les limites d’exposition aux rayonnements definies pour un contrôlé environnement. Cet émetteur ne doit pas être co-localisés ou fonctionner en conjunction avec une autre antenne ou émetteur. Cet équipement doit être installé et utilisé avec un minimum de 2.5cm de distance entre le radiateur et votre corps. Electromagnetic Interference/Compatibility This device complies with Part 15 of the FCC Rules. Operation is subject to the following two conditions: 1. This device may not cause harmful interference, and 2. This device must accept any interference received, including interference that may cause undesired operation. Changes or modifications not expressly approved by the party responsible for compliance could void your authority to operate the equipment. Avis de conformité à la FCC : Ce dispositif a été testé et s’avère conforme à l’article 15 des règlements de la Commission fédérale des communications (FCC). Ce dispositif est soumis aux conditions suivantes: 1) Ce dispositif ne doit pas causer d’interférences nuisibles et; 2) Il doit pouvoir supporter les parasites qu’il reçoit, incluant les parasites pouvant nuire à son fonctionnement. Tout changement ou modification non approuvé expressément par la partie responsable pourrait annuler le droit à l’utilisateur de faire fonctionner cet équipement. This device complies with Industry Canada license-exempt RSS standard(s). Operation is subject to the following two conditions: 1. This device may not cause interference, and 2. This device must accept any interference received, including interference that may cause undesired operation of the device. FCC Part 15.21 Warning Statement NOTE: THE GRANTEE IS NOT RESPONSIBLE FOR ANY CHANGES OR MODIFICATIONS NOT EXPRESSLY APPROVED BY THE PARTY RESPONSIBLE FOR COMPLIANCE. SUCH MODIFICATIONS COULD VOID THE USER’S AUTHORITY TO OPERATE THE EQUIPMENT. Safety and General Information WARNING: Changes or modifications to this unit not expressly approved by the party responsible for compliance could void the user’s authority to operate the equipment. This device complies with Part 15 of the FCC Rules. Operation is subject to the following two conditions: 1) This device may not cause harmful interference, and 2) this device must accept any interference received, including interference that may cause undesired operation. NOTE: This equipment has been tested and found to comply with the limits for a Class B digital device, pursuant to Part 15 of the FCC Rules. These limits are designed to provide reasonable protection against harmful interference in a residential installation. This equipment generates, uses and can rad…

Text truncated - open the document above for the full version.

PO FUNG ELECTRONIC (HK) INTERNATONAL GROUP COMPANY LIMITED Room 1508, 15/F, Office Tower II, Grand Plaza, 625 Nathan Road, Kowloon, Hong Kong Federal Communications Commission Authorization and Evaluation Division 7435 Oakland Mills Road Columbia, MD 21046 USA Date: Oct. 10, 2024 Ref: Attestation Statements Part 2.911(d)(5)(i) Filing FCC ID: 2AJGM-888S FRN: 0025809377 PO FUNG ELECTRONIC (HK) INTERNATONAL GROUP COMPANY LIMITED (“the applicant”) certifies that the equipment for which authorization is sought is not “covered” equipment prohibited from receiving an equipment authorization pursuant to section 2.903 of the FCC rules. Sincerely, __________________________ Peter Wang, Manager

PO FUNG ELECTRONIC (HK) INTERNATONAL GROUP COMPANY LIMITED Room 1508, 15/F, Office Tower II, Grand Plaza, 625 Nathan Road, Kowloon, Hong Kong Federal Communications Commission Authorization and Evaluation Division 7435 Oakland Mills Road Columbia, MD 21046 USA Date: Qct. 10, 2024 Ref: Attestation Statements Part 2.911(d)(5)(ii) Filing FCC ID: 2AJGM-888S FRN: 0025809377 PO FUNG ELECTRONIC (HK) INTERNATONAL GROUP COMPANY LIMITED (“the applicant”) certifies that, as of the date of the filing of the application, the applicant is not identified on the Covered List as an entity producing “covered” equipment. Sincerely, __________________________ Peter Wang, Manager

U.S. AGENT LETTER OF ATTESTATION Date: 2024-09-21 FEDERAL COMMUNICATIONS COMMISSION Authorization and Evaluation Division 7435 Oakland Mills Road Columbia, MD 21046 Ref: Attestation Statements CFR 47 §2.911(d)(7) Filing FCC ID: 2AJGM-888S PO FUNG ELECTRONIC (HK) INTERNATONAL GROUP COMPANY LIMITED (“the Applicant”) certifies that, as of the date of the filing of the application, Iconsigh Inc. is our designated U.S. agent for service of process for the above referenced FCC ID. PO FUNG ELECTRONIC (HK) INTERNATONAL GROUP COMPANY LIMITED (“the Applicant”) accepts to maintain an agent for no less than one year after the grantee has terminated all marketing and importation or the conclusion of any Commission-related proceeding involving the equipment. Iconsigh Inc. accepts, as of the date of the filing of the application, the obligation of the designated U.S. agent for service of process for the above referenced FCC ID. Designated U.S. Agent Information: Company Name: Iconsigh Inc. Address: 2310 Homestead Road, Suite C1, Los Altos, CA, 94024, USA FRN: 0033398652 Tel.: +1 (408) 320-9867 Email: [email protected] Signed by (printed name): Benjamin Kaur Signature: Applicant: PO FUNG ELECTRONIC (HK) INTERNATONAL GROUP COMPANY LIMITED Room 1508, 15/F, Office Tower II, Grand Plaza, 625 Nathan Road, Kowloon, Hong Kong FRN: 0025809377 Tel: 00852-90831684 Email: [email protected] Signed by (printed name): Peter Wang Signature:

PO FUNG ELECTRONIC (HK) INTERNATONAL GROUP COMPANY LIMITED Room 1508, 15/F, Office Tower II, Grand Plaza, 625 Nathan Road, Kowloon, Hong Kong Date: Oct 10, 2024 FEDERAL COMMUNICATIONS COMMISSIONS Authorization and Evaluation Division 7435 Oakland Mills Road Columbia, MD 21046 Subject: Extended Frequencies Justification for Certification of Transmitter with FCC ID: 2AJGM-888S Dear Sir/Madam, This transmitter was designed to operate in following frequency ranges 400-470Mhz To aid equipment authorization in other countries which accept the United States FCC Grant for Certification, PO FUNG ELECTRONIC (HK) INTERNATONAL GROUP COMPANY LIMITED is requesting that the FCC lists the frequencies 400-470MHz, under FCC Rule Parts 90 on the FCC Grant. PO FUNG ELECTRONIC (HK) INTERNATONAL GROUP COMPANY LIMITED attests that the Two Way Radio will not be marketed to USA users with the frequency band which is not allowed by the rule part 90. Per the FCC’s KDB634817 guidance, as an alternative to listing the exact frequencies, we acknowledge that it’s a violation of the FCC Rules if this device operates on unauthorized frequencies. Frequency Range (MHz） FCC Rule Part 400-406MHz For Federal 406.1-450MHz FCC Part 90 450-454MHz FCC Part 90 456-460MHz FCC Part 90 460-462.5375MHz FCC Part 90 462.7375-467.5375MHz FCC Part 90 467.7375-470MHz FCC Part 90 Also, equipment programming is the responsibility of Authorized Service Personnel, the Two Way Radio complies with 47 CFR Part 90.203(e), in that the operator cannot directly program the transmit frequencies using the normally accessible external controls. Please contact me if you require any additional information. Sincerely Yours, Signature: __________________________ Peter Wang, Manager

PO FUNG ELECTRONIC (HK) INTERNATONAL GROUP COMPANY LIMITED Room 1508, 15/F, Office Tower II, Grand Plaza, 625 Nathan Road, Kowloon, Hong Kong Date: 2024-10-10 FCC Part 90 Letter FEDERAL COMMUNICATIONS COMMISSION Authorization and Evaluation Division 7435 Oakland Mills Road Columbia, MD 21046 Subject: Declaration of compliance to the requirements of §90.203 with FCC ID: 2AJGM-888S Dear Sir/Madam, We, PO FUNG ELECTRONIC (HK) INTERNATONAL GROUP COMPANY LIMITED acknowledge that this device will not be marketed to USA users with the frequency band which is not allowed by rule part 90.and it is a violation of FCC rules if this device is operated on unauthorized frequencies inside the U.S.A. This equipment meets the requirements of the FCC Rules, Parts 90.203(e) and (g), as applicable. Programming of this products transmit frequencies can be performed ONLY by the manufacturer or by service or by maintenance personal. The operator can’t program transmit frequencies using the equipment’s external operation controls. This is to certify that the requirements of 47 CFR Part 90.203(j)(4) and (5) spectrum efficiency are met by the PO FUNG ELECTRONIC (HK) INTERNATONAL GROUP COMPANY LIMITED demonstrated by the tests conducted on the sample radio provided. Additionally, the radio also meets the requirement of one voice channel per 12.5 kHz of channel bandwidth for analogue speech (11k0F3E emission). Sincerely Yours, Signature: __________________________ Peter Wang, Manager

PO FUNG ELECTRONIC (HK) INTERNATONAL GROUP COMPANY LIMITED Room 1508, 15/F, Office Tower II, Grand Plaza, 625 Nathan Road, Kowloon, Hong Kong Agent Authorization Company: PO FUNG ELECTRONIC (HK) INTERNATONAL GROUP COMPANY LIMITED Address: Room 1508, 15/F, Office Tower II, Grand Plaza, 625 Nathan Road, Kowloon, Hong Kong Product Name: TWO-WAY RADIO Model Number(s): BF-888S Product Description: TWO-WAY RADIO We authorize MiCOM Labs Inc., 575 Boulder Court, Pleasanton, California 94566, USA, to act on our behalf on all matters concerning the certification of above named equipment. We declare that MiCOM Labs Inc. is allowed to forward all information related to the approval and certification of equipment to the regulatory agencies as required and to discuss any issues concerning the approval application. Any and all acts carried out by MiCOM Labs on our behalf shall have the same effect as acts of our own. Signature: Date: Oct. 10, 2024 Name: Peter Wang Company: PO FUNG ELECTRONIC (HK) INTERNATONAL GROUP COMPANY LIMITED

PO FUNG ELECTRONIC (HK) INTERNATONAL GROUP COMPANY LIMITED Room 1508, 15/F, Office Tower II, Grand Plaza, 625 Nathan Road, Kowloon, Hong Kong Office of Engineering Technology Federal Communications Commission 7435 Oakland Mills Road Columbia, MD 21046 USA Date: Oct. 10, 2024 Subject; Request for Confidentiality FCC ID: 2AJGM-888S To Whom It May Concern, Pursuant to the provisions of the Commission’s rules Title 47 Sections §0.457 and §0.459, we are requesting the Commission to withhold the following attachment(s) as confidential documents from public disclosure indefinitely. These documents contain detailed system and equipment descriptions and are considered as proprietary information in operation of the equipment. The public disclosure of these documents might be harmful to our company and would give competitors an unfair advantage in the market. Schematic Diagram Block Diagram Parts List Operational Description Tune-up Procedure In additional to above mentioned documents, in order to comply with the marketing regulations in Title 47 CFR §2.803 and the importation rules in Title 47 CFR §2.1204, while ensuring that business sensitive information remains confidential until the actual marketing of newly authorized devices, we request Short Term Confidentiality of the following attachment(s); External Photos Test Setup Photos Internal Photos User Manual For 45 days, pursuant to Public Notice DA 04-1705. OR For 180 days pursuant to KDB 726920 D01. It is our understanding that all measurement test reports, FCC ID label format and correspondence during the certification review process cannot be granted as confidential documents and this information will be available for public review once the grant of equipment authorization is issued. Sincerely __________________________ Peter Wang, Manager

Report No.: AGC02294240901AP02 Page 1 of 5 EXTERNAL PHOTOS All VIEW OF EUT TOP VIEW OF EUT PTT Antenna Report No.: AGC02294240901AP02 Page 2 of 5 BOTTOM VIEW OF EUT FRONT VIEW OF EUT Report No.: AGC02294240901AP02 Page 3 of 5 BACK VIEW OF EUT LEFT VIEW OF EUT Report No.: AGC02294240901AP02 Page 4 of 5 RIGHT VIEW OF EUT ADAPTER OF EUT Report No.: AGC02294240901AP02 Page 5 of 5 CHARGER OF EUT ****************************************End of Report*************************************

FCC ID Label Location 40mm&30mm FCC ID: 2AJGM-888S WARNING: MODIFICATION OF THIS DEVICE TO RECEIVE CELLULAR RADIOTELEPHONE SERVICE SIGNALS IS PROHIBITED UNDER FCC RULES AND FEDERAL LAW.

Report No.: AGC02294240901AP02 Page 1 of 7 INTERNAL PHOTOS PORT OF EUT OPEN VIEW OF EUT (FIGURE 1) Report No.: AGC02294240901AP02 Page 2 of 7 OPEN VIEW OF EUT (FIGURE 2) OPEN VIEW OF EUT (FIGURE 3) Report No.: AGC02294240901AP02 Page 3 of 7 INTERNAL VIEW OF EUT (FIGURE 1) INTERNAL VIEW OF EUT (FIGURE 2) Report No.: AGC02294240901AP02 Page 4 of 7 INTERNAL VIEW OF EUT (FIGURE 4) INTERNAL VIEW OF EUT (FIGURE 5) Report No.: AGC02294240901AP02 Page 5 of 7 INTERNAL VIEW OF EUT (FIGURE 6) INTERNAL VIEW OF EUT (FIGURE 8) Report No.: AGC02294240901AP02 Page 6 of 7 INTERNAL VIEW OF EUT (FIGURE 9) INTERNAL VIEW OF EUT (FIGURE 10) Report No.: AGC02294240901AP02 Page 7 of 7 BATTERY OF EUT ****************************************End of Report*************************************

Page 1 of 37 SAR Test Report Report No.: AGC02294240901FH01 FCC ID : 2AJGM-888S PRODUCT DESIGNATION : TWO-WAY RADIO BRAND NAME : BAOFENG MODEL NAME : BF-888S APPLICANT : PO FUNG ELECTRONIC (HK) INTERNATONAL GROUP COMPANY LIMITED DATE OF ISSUE : Sep. 25, 2024 STANDARD(S) : IEEE Std. 1528:2013 FCC 47 CFR Part 2§2.1093 IEEE Std C95.1 ™-2005 REPORT VERSION : V1.0 Attestation of Global Compliance(Shenzhen) Co., Ltd. Report No.: AGC02294240901FH01 Page 2 of 37 Report Revise Record Report Version Revise Time Issued Date Valid Version Notes V1.0 / Sep. 25, 2024 Valid Initial Release Report No.: AGC02294240901FH01 Page 3 of 37 Test Report Applicant Name PO FUNG ELECTRONIC (HK) INTERNATONAL GROUP COMPANY LIMITED Applicant Address Room 1508, 15/F, Office Tower II, Grand Plaza, 625 Nathan Road, Kowloon, Hong Kong Manufacturer Name PO FUNG ELECTRONIC (HK) INTERNATONAL GROUP COMPANY LIMITED Manufacturer Address Room 1508, 15/F, Office Tower II, Grand Plaza, 625 Nathan Road, Kowloon, Hong Kong Factory Name PO FUNG ELECTRONIC (HK) INTERNATONAL GROUP COMPANY LIMITED Factory Address Room 1508, 15/F, Office Tower II, Grand Plaza, 625 Nathan Road, Kowloon, Hong Kong Product Designation TWO-WAY RADIO Brand Name BAOFENG Model Name BF-888S Series Model N/A Declaration Difference N/A EUT Voltage DC 3.7V Applicable Standard IEEE Std. 1528:2013 FCC 47 CFR Part 2§2.1093 IEEE Std C95.1 ™-2005 Date of receipt of test item Sep. 03, 2024 Test Date Sep. 13, 2024 Report Template AGCRT- US -PTT/SAR (2021-04-20) Note: The results of testing in this report apply to the product/system which was tested only. Prepared By Bibo Zhang (Project Engineer) Sep. 25, 2024 Reviewed By Calvin Liu (Reviewer) Sep. 25, 2024 Approved By Max Zhang (Authorized Officer) Sep. 25, 2024 Report No.: AGC02294240901FH01 Page 4 of 37 TABLE OF CONTENTS 1. SUMMARY OF MAXIMUM SAR VALUE ......................................................................................................... 5 2. GENERAL INFORMATION ............................................................................................................................... 6 2.1. EUT DESCRIPTION......................................................................................................................................... 6 3. SAR MEASUREMENT SYSTEM ........................................................................................................................ 7 3.1. THE DASY5 SYSTEM USED FOR PERFORMING COMPLIANCE TESTS CONSISTS OF FOLLOWING ITEMS .................... 7 3.2. DASY5 E-FIELD PROBE ................................................................................................................................. 8 3.3. DATA ACQUISITION ELECTRONICS DESCRIPTION ............................................................................................... 8 3.4. ROBOT .......................................................................................................................................................... 9 3.5. LIGHT BEAM UNIT .......................................................................................................................................... 9 3.6. DEVICE HOLDER .......................................................................................................................................... 10 3.7. MEASUREMENT SERVER ............................................................................................................................... 10 3.8. PHANTOM ................................................................................................................................................. 11 4. SAR MEASUREMENT PROCEDURE ............................................................................................................ 12 4.1. SPECIFIC ABSORPTION RATE (SAR) .............................................................................................................. 12 4.2. SAR MEASUREMENT PROCEDURE ................................................................................................................ 13 5. TISSUE SIMULATING LIQUID ....................................................................................................................... 15 5.1. THE COMPOSITION OF THE TISSUE SIMULATING LIQUID..................................................................................... 15 5.2. TISSUE DIELECTRIC PARAMETERS FOR HEAD AND BODY PHANTOMS ............................................................... 15 5.3. TISSUE CALIBRATION RESULT ....................................................................................................................... 16 6. SAR SYSTEM CHECK PROCEDURE ........................................................................................................... 17 6.1. SAR SYSTEM CHECK PROCEDURES ............................................................................................................. 17 7. EUT TEST POSITION ...................................................................................................................................... 19 7.1. BODY WORN POSITION ................................................................................................................................ 19 8. SAR EXPOSURE LIMITS ............................................................................................................................... 20 9. TEST FACILITY .............................................................................................................................................. 21 10. TEST EQUIPMENT LIST .............................................................................................................................. 22 11. MEASUREMENT UNCERTAINTY ................................................................................................................ 23 12. POWER MEASUREMENT ...........................................................................................................…

Text truncated - open the document above for the full version.

Page 1 of 18 CALIBRATION DATA PROBE CALIBRATION DATA Page 2 of 18 Page 3 of 18 Page 4 of 18 Page 5 of 18 Page 6 of 18 Page 7 of 18 Page 8 of 18 Page 9 of 18 Page 10 of 18 DAE CALIBRATION DATA Page 11 of 18 Page 12 of 18 Page 13 of 18 DIPOLE CALIBRATION DATA Page 14 of 18 Page 15 of 18 Page 16 of 18 Page 17 of 18 Page 18 of 18

Page 1 of 45 FCC Test Report Report No.: AGC02294240901FR01 FCC ID : 2AJGM-888S APPLICATION PURPOSE : Original Equipment PRODUCT DESIGNATION : TWO-WAY RADIO BRAND NAME : BAOFENG MODEL NAME : BF-888S APPLICANT : PO FUNG ELECTRONIC (HK) INTERNATONAL GROUP COMPANY LIMITED DATE OF ISSUE : Sep. 27, 2027 STANDARD(S) : FCC Part 90 Subpart I REPORT VERSION : V1.0 Attestation of Global Compliance (Shenzhen) Co., Ltd Report No.: AGC02294240901FR01 Page 2 of 45 Report Revise Record Report Version Revise Time Issued Date Valid Version Notes V1.0 / Sep. 27, 2027 Valid Initial Release Report No.: AGC02294240901FR01 Page 3 of 45 Table of Contents 1. General Information ........................................................................................................................................ 5 2. Product Information ........................................................................................................................................ 6 2.1 Product Technical Description ................................................................................................................... 6 2.2 Test Frequency List ................................................................................................................................... 7 2.3 Related Submittal(S) / Grant (S) ............................................................................................................... 8 2.4 Test Methodology ...................................................................................................................................... 8 2.5 Calculation of Emission Indicators ............................................................................................................ 8 2.6 Special Accessories .................................................................................................................................. 8 2.7 Equipment Modifications ........................................................................................................................... 8 3. Test Environment ............................................................................................................................................ 9 3.1 Address of The Test Laboratory ................................................................................................................ 9 3.2 Test Facility ................................................................................................................................................ 9 3.3 Environmental Conditions ....................................................................................................................... 10 3.4 Measurement Uncertainty ....................................................................................................................... 10 3.5 List of Equipment Used ........................................................................................................................... 11 4.System Test Configuration ............................................................................................................................ 13 4.1 EUT Configuration ................................................................................................................................... 13 4.2 EUT Exercise ........................................................................................................................................... 13 4.3 Configuration of Tested System .............................................................................................................. 13 4.4 Equipment Used in Tested System ......................................................................................................... 13 4.5 Summary of Test Results ........................................................................................................................ 14 5. Description of Test Modes ........................................................................................................................... 15 6. Frequency Stability ....................................................................................................................................... 16 6.1 Provisions Applicable .............................................................................................................................. 16 6.2 Measurement Procedure ......................................................................................................................... 16 6.3 Measurement Setup ................................................................................................................................ 16 6.4 Measurement Result ............................................................................................................................... 17 7. 26dB Emission Bandwidth and 99% Occupied Bandwidth ...................................................................... 18 7.1 Provisions Applicable .............................................................................................................................. 18 7.2 Measurement Procedure ......................................................................................................................... 18 7.3 Measurement Setup ................................................................................................................................ 18 7.4 Measurement Result ............................................................................................................................... 19 8. Spurious Radiated Emission ......................................................................................................................... 20 8.1 Provisions Applicable .............................................................................................................................. 20 8.2 Measurement Procedure .........................................................................................…

Text truncated - open the document above for the full version.

Report No.: AGC02294240901AP01 Page 1 of 2 TEST SETUP PHOTOS RADIATED EMISSION TEST SETUP BELOW 1GHz RADIATED EMISSION TEST SETUP ABOVE 1GHz Report No.: AGC02294240901AP01 Page 2 of 2 RF CONDUCTED TEST SETUP ****************************************End of Report*************************************