2AJGM-AT2Two Way Radio

AT 2 Series Two-way Radio User Manual Please read this manual carefully before using the product and retain it for future reference Android IOS Radio Overview Keys Press Press and hold SK1 Vol+ Increase volume, step 1 Monitor Function SK2 Vol- Decrease volume, step 1 Menu Mode/Confirm Button TK Exit menu Power On/Off 1. Antenna 2. PTT button 3. Volume Up/Monitor 4. Volume Down/Menu 5. PTT button 6. Microphone 7. TX indicator (red light) 8. RX indicator (green light) 9.Built-in speaker 10. Headset/Programming port 11. Type-C charging port 12. BT Bluetooth indicator (blue light) 13. Charging complete (white light) 14. Charging in progress (white light) 15. Back clip 16. Power switch/Exit key 17. Encoder/Menu list toggle Status Indications The top LED will help you to identify the current radio status. Always on Not lit Bright 7 Red light Transmitting... Standby ------ 8 Green light Receiving... Standby Scanning 12 Blue light Bluetooth enabled Bluetooth off Bluetooth disconnected 13 White light Charging complete Charging... ----- 14 White light Charging... Battery failure (no battery detected) ｜Packing List Welcome to ALEVITES Two-way Radio. Before use, we recommend: Please unpack carefully and check that you have received the following items. If any item is missing or damaged, contact your dealer. Item Quantity (PCS) Radio 1 Battery 1 Charge Cable 1 Belt Clip 1 User Manual 1 Note: Figures in this manual are for reference only. ｜Before Use 1. Attaching the Battery a. Use the approved battery to avoid the risk of explosion. b. Dispose of the used battery according to "Precautions for Disposal" in the Safety Information Booklet. 2. Attaching the Belt Clip Align the belt clip bracket with the clip slot on the back of the radio. Slide it downward until the clip locks into place. To remove, press the locking pivot on the clip to disengage it, then slide the clip upward until it separates from the radio. 3. Attaching the Audio Accessory Open the audio jack cover, and then insert the audio accessory into the jack. 4. Charging the Battery Use the approved charger to charge the battery. NOTE: The remaining lithium-ion battery power is limited to 30% pursuant to the new lithium battery shipment regulation approved by the International Air Transport Association (IATA). Before initial use, charge the battery. Use the USB Type-C charge cable to connect the radio with battery attached to the power adapter, power bank, or PC. When powered off, the indicator light glows red during charging and turns green when fully charged. When powered on, the top notification bar’s battery icon displays green during charging, the top indicator glows red, and it switches to green once fully charged. ｜Basic Operations 1. Turn the radio on and off Press and hold the key to turn the radio on or off. • Turning the radio on will be accompanied by the voice prompt “Power on” and the current channel. • Turning the radio off will be accompanied by the voice prompt “Power off”. 2. Eight-level volume adjustment. • Press the SK1 key (Vol+) to increase the volume by one level each time. • Press the SK2 key (Vol-) to decrease the volume by one level each time. 3. Channel Selection Rotate the channel knob to select channels. Turning clockwise changes the channel incrementally by one. Turning counterclockwise decreases the channel incrementally by one. 1）Voice announcement of channel sequence. For digital channels, prompts “Digital”. 2）Empty Channel (Unedited Parameters) Alert Prompt. 4. Call Service Making a Call • Rotate the channel knob to select a channel, then press and hold the PTT button to initiate a call. The red indicator light remains solid. • Release the PTT button and wait to receive the call. Receiving Calls • For analog calls, the RX indicator illuminates solid green. • For digital calls, the RX indicator illuminates solid amber (combination of red and green lights). Dual PTT Transmission Function 1）The PTT button on the left side of the radio is the Main PTT, which always transmits and receives on the main channel. 2）The PTT button on the front of the radio is the sub-P T T. • When the sub-PTT is set to follow the PTT channel, it functions identically to the Main PTT, transmitting on the current channel. • When the sub-PTT is set to a designated channel, it always transmits on the preset channel. The radio enables dual-channel monitoring, simultaneously monitoring the main channel (current channel) and the channel associated with the sub-P T T. 5. Monitor Press and hold [SK1] (Monitor function) to keep the speaker active (disable squelch) and listen for faint wireless signals. Release to exit monitoring mode. 6. Frequency Sweep Function • Rotate the channel knob to Channel 1 to turn off the radio. • Press and hold the 【PTT】 + 【SK1】 keys to power on. The voice prompt “On (Frequency Sweep Function On), Power On” will sound, entering the sweep function with the green LED flashing. Press the 【SK1】 key to hear a “beep” and see the green LED turn solid, initiating the sweep. Upon completion, frequencies are automatically stored with two “beep” tones. (Green LED stays on during scanning; flashes when stopped) • Rotate the channel knob to Channel 2. Briefly press [SK1] to resume scanning. After completion, frequencies are stored with two “beep” tones and indicator lights behave as described above. • Rotate the channel knob to Channel 3, briefly press the [SK1] key to continue scanning. Upon completion, the frequency will be automatically stored with a “beep-beep” sound prompt. Repeat this process sequentially up to Channel 16. • After completing the scanning task, power off and restart to exit scan mode, concluding the scanning operation. 7. Wireless Cloning Function • Rotate the channel knob to Channel 2 and turn off the radio. • On the transmitter, press and hold [PTT] + [SK1] to power on. The transmitter will beep once to enter wireless cloning mode. • On the receiver, press and hold [PTT] + [SK1] to power on. The receiver w…

Text truncated - open the document above for the full version.

PO FUNG ELECTRONIC (HK) INTERNATONAL GROUP COMPANY LIMITED Room 1508, 15/F, Office Tower II, Grand Plaza, 625 Nathan Road, Kowloon, Hong Kong 1 | Page Attestation Statements To: Federal Communications Commission Date: Apr. 3, 26 7435 Oakland Mills Road, Columbia, MD 21046, USA Subject: Attestation of Compliance with FCC Covered List Software Requirements FCC ID: 2AJGM-AT2 Product Name:Two Way Radio This letter serves as an attestation that the equipment identified above ☐ is / ☒ is not (select one) "covered" software as defined under the Federal Communications Commission (FCC) Covered List requirements, as outlined in FCC 22-84 and KDB 986446. Specifically, the undersigned certifies that the equipment for which authorization is sought: 1. Does not contain cybersecurity or anti-virus software produced or provided by Kaspersky Lab, Inc. or any of its successors, assignees, parents, subsidiaries, affiliates, or any entity that has rebranded or relabeled software produced by the aforementioned entities. 2. Does not have the capability to store, run, or deliver any software identified on the FCC Covered List, including but not limited to cybersecurity and anti-virus software. To support this attestation, the appendix evaluation documentation has been prepared and is included in the certification filing. This attestation is based on a thorough evaluation of the device's design, functionality, and software environment. The undersigned affirms that the information provided is accurate and complete to the best of their knowledge. Sincerely yours, Name: Peter Wang Title: General Manager PO FUNG ELECTRONIC (HK) INTERNATONAL GROUP COMPANY LIMITED Room 1508, 15/F, Office Tower II, Grand Plaza, 625 Nathan Road, Kowloon, Hong Kong 2 | Page Evaluation regarding to the Covered List Software: Compliance Methodology Evaluation Process Results Device is Inherent compliance ☒ The Chipset(s) used is limited to run the Cybersecurity or anti-virus software. Compliance ☐ The Memory used is limited to run the Cybersecurity or anti-virus software. Compliance ☐ There is storage capacity limitation for store or install the Cybersecurity or anti-virus software. Compliance ☐ Operating system used is limited to run, install or deliver the Cybersecurity or anti-virus software. Compliance Device is not Inherent compliance ☐ Evaluation Based on Software Bill of Materials (SBoM) Compliance ☐ Evaluation Based on Scan for Software on the device ☐ Evaluation Based on Filesystem scan ☐ Evaluation Based on Running software check SBOM (Software Bill of Materials) [For Device is not Inherent compliance] Section Component Name Version Supplier 1 2 3

2.911 (d)(7)USA Agent v1.2 Section 2.911(d)(7) USA Agent for Service of Process Company name: PO FUNG ELECTRONIC (HK) INTERNATONAL GROUP COMPANY LIMITED Address: Room 1508, 15/F, Office Tower II, Grand Plaza, 625 Nathan Road, Kowloon, Hong Kong FCC ID: 2AJGM-AT2 Date: 2026-04-03 2.911(d)(7) USA Designated Agent for Service of Process We, [PO FUNG ELECTRONIC (HK) INTERNATONAL GROUP COMPANY LIMITED] (“the applicant”) designate [Wedo Group] NOTE1 for the purpose of accepting service of process on behalf of the applicant. Applicant consent: We Acknowledge our consent to accept service of process in the United States for matters related to the applicable equipment, and at the physical U.S. address and email address of the designated agent and acknowledge our acceptance of our obligation to maintain an agent for service of process in the United States for no less than one year after either the grantee has permanently terminated all marketing and importation of the applicable equipment within the U.S., or the conclusion of any Commission-related administrative or judicial proceeding involving the equipment, whichever is later. Agent obligation: We Acknowledge our obligation to accept service of process in the United States for matters related to the applicable equipment at our physical U.S. address and email address for no less than one year after either the grantee has permanently terminated all marketing and importation of the applicable equipment within the U.S., or the conclusion of any Commission-related administrative or judicial proceeding involving the equipment, whichever is later. USA Agent Company name: Wedo Group Address: 710 Arabian Ln Walnut, CA 91789, United States FRN：0037730611 Contact Name: Jeffrey Chen Telephone No: (323) 528-1888 Email: [email protected] Applicant Company name: PO FUNG ELECTRONIC (HK) INTERNATONAL GROUP COMPANY LIMITED Address: Room 1508, 15/F, Office Tower II, Grand Plaza, 625 Nathan Road, Kowloon, Hong Kong FRN: 0025809377 Contact Name: Peter Wang Telephone No: 00852-90831684 Email: [email protected] Signature: Signature:

PO FUNG ELECTRONIC (HK) INTERNATONAL GROUP COMPANY LIMITED Room 1508, 15/F, Office Tower II, Grand Plaza, 625 Nathan Road, Kowloon, Hong Kong Attestation Statements Not Covered Entity Applicant & Not Covered Equipment To: Federal Communications Commission Date: April 3, 2026 7435 Oakland Mills Road, Columbia, MD 21046, USA Ref: Information Required by Section 2.911(d)(5)(i) & (ii) FCC ID: 2AJGM-AT2 PO FUNG ELECTRONIC (HK) INTERNATONAL GROUP COMPANY LIMITED (“the applicant”) certifies that, as of the date of the filing of the application, the applicant is not identified on the Covered List, established pursuant to § 1.50002 of reference chapter, as an entity producing “covered” communication equipment. The equipment for which authorization is sought is not “covered” telecommunications equipment and video surveillance equipment produced by entities identified on the Commission’s Covered List that prohibited from receiving an equipment authorization pursuant to section § 2.903 of the FCC rules. Sincerely yours, Name: Peter Wang Title: General Manager

PO FUNG ELECTRONIC (HK) INTERNATONAL GROUP COMPANY LIMITED Room 1508, 15/F, Office Tower II, Grand Plaza, 625 Nathan Road, Kowloon, Hong Kong Office of Engineering Technology Federal Communications Commission 7435 Oakland Mills Road Columbia, MD 21046 USA Date: 2026-04-03 Subject; Request for Confidentiality FCC ID: 2AJGM-AT2 To Whom It May Concern, Pursuant to the provisions of the Commission’s rules Title 47 Sections §0.457 and §0.459, we are requesting the Commission to withhold the following attachment(s) as confidential documents from public disclosure indefinitely. These documents contain detailed system and equipment descriptions and are considered as proprietary information in operation of the equipment. The public disclosure of these documents might be harmful to our company and would give competitors an unfair advantage in the market. Schematic Diagram Block Diagram Parts List Operational Description Tune-up Procedure In additional to above mentioned documents, in order to comply with the marketing regulations in Title 47 CFR §2.803 and the importation rules in Title 47 CFR §2.1204, while ensuring that business sensitive information remains confidential until the actual marketing of newly authorized devices, we request Short Term Confidentiality of the following attachment(s); External Photos Test Setup Photos Internal Photos User Manual For 45 days, pursuant to Public Notice DA 04-1705. OR For 180 days pursuant to KDB 726920 D01. It is our understanding that all measurement test reports, FCC ID label format and correspondence during the certification review process cannot be granted as confidential documents and this information will be available for public review once the grant of equipment authorization is issued. Sincerely __________________________ Peter Wang, Manager

PO FUNG ELECTRONIC (HK) INTERNATONAL GROUP COMPANY LIMITED Room 1508, 15/F, Office Tower II, Grand Plaza, 625 Nathan Road, Kowloon, Hong Kong 2026-04-03 Federal Communications Commission Authorization and Evaluation Division 7435 Oakland Mills Road Columbia, MD 21046 Subject: Agent Authorization for FCC ID: 2AJGM-AT2 I, the undersigned, hereby authorize (Attestation of Global Compliance (Shenzhen) Co., Ltd) to act on our behalf in all matters relating to this application for equipment certification. Any act carried out by (Attestation of Global Compliance (Shenzhen) Co., Ltd) shall have the same effect as our own and I acknowledge that all responsibility for complying with the terms and conditions of certification, as specified by DERYCOM CERTIFICATION SERVICES, INC., still resides with (PO FUNG ELECTRONIC (HK) INTERNATONAL GROUP COMPANY LIMITED). We certify that we are not subject to a denial of federal benefits that includes FCC benefits pursuant to Section 5301 of the Anti-Drug Abuse Act of 1988, 21 U.S.C. §862, and that no party to the application, as defined in 47 CFR §1.2002(b), is subject to a denial of federal benefits that includes FCC benefits pursuant to that section. Sincerely, (Peter Wang) (Manager) Tel: 00852-90831684 Fax: 00852-90831684 Email: [email protected]

PO FUNG ELECTRONIC (HK) INTERNATONAL GROUP COMPANY LIMITED Room 1508, 15/F, Office Tower II, Grand Plaza, 625 Nathan Road, Kowloon, Hong Kong 2026-04-03 Office of Engineering Technology Federal Communications Commission 7435 Oakland Mills Road Columbia, MD 21046 USA Subject: Explanation of differences between product types FCC ID: 2AJGM-AT2 Models: AT2, AT2 PRO Brand name: BAOFENG, POFUNG, ALERVITES To Whom It May Concern: We, The PO FUNG ELECTRONIC (HK) INTERNATONAL GROUP COMPANY LIMITED hereby declare that the model : AT2 is identical with the model : AT2 PRO, Except for the model name and brand name, everything else is same. Sincerely, PO FUNG ELECTRONIC (HK) INTERNATONAL GROUP COMPANY LIMITED Signature: [General Manager]

Report No.: AGC02294251205AP02 Page 1 of 5 EXTERNAL PHOTOS All View of EUT Top View of EUT UHF Antenna Report No.: AGC02294251205AP02 Page 2 of 5 Bottom View of EUT Front View of EUT Report No.: AGC02294251205AP02 Page 3 of 5 Back View of EUT Left View of EUT Report No.: AGC02294251205AP02 Page 4 of 5 Right View of EUT Port-1 View of EUT Report No.: AGC02294251205AP02 Page 5 of 5 Port-2 View of EUT Adapter View of EUT ****************************************End of Report*************************************

FCC ID Label Location FCC ID: 2AJGM-AT2 30mm*30mm

Report No.: AGC02294251205AP02 Page 1 of 5 INTERNAL PHOTOS Open View-1 of EUT Open View-2 of EUT Report No.: AGC02294251205AP02 Page 2 of 5 Open View-3 of EUT Battery View of EUT Report No.: AGC02294251205AP02 Page 3 of 5 Internal View-1 of EUT Internal View-2 of EUT Report No.: AGC02294251205AP02 Page 4 of 5 Internal View-3 of EUT Internal View-4 of EUT Report No.: AGC02294251205AP02 Page 5 of 5 Internal View-5 of EUT Internal View-6 of EUT ****************************************End of Report************************************* BT Antenna

Page 1 of 43 SAR Test Report Report No.: AGC02294251205FH01 FCC ID : 2AJGM-AT2 APPLICATION PURPOSE : Original Equipment PRODUCT DESIGNATION : Two Way Radio BRAND NAME : BAOFENG, POFUNG, ALERVITES MODEL NAME : AT2, AT2 PRO APPLICANT : PO FUNG ELECTRONIC (HK) INTERNATONAL GROUP COMPANY LIMITED DATE OF ISSUE : Apr. 02, 2026 STANDARD(S) : IEEE Std. 1528:2013 FCC 47 CFR Part 2§2.1093 IEEE Std C95.1 ™-2019 REPORT VERSION : V1.0 Attestation of Global Compliance(Shenzhen) Co., Ltd. Report No.: AGC02294251205FH01 Page 2 of 43 Report Revise Record Report Version Revise Time Issued Date Valid Version Notes V1.0 / Apr. 02, 2026 Valid Initial Release Report No.: AGC02294251205FH01 Page 3 of 43 Test Report Applicant Name PO FUNG ELECTRONIC (HK) INTERNATONAL GROUP COMPANY LIMITED Applicant Address Room 1508, 15/F, Office Tower II, Grand Plaza, 625 Nathan Road, Kowloon, Hong Kong Manufacturer Name PO FUNG ELECTRONIC (HK) INTERNATONAL GROUP COMPANY LIMITED Manufacturer Address Room 1508, 15/F, Office Tower II, Grand Plaza, 625 Nathan Road, Kowloon, Hong Kong Factory Name PO FUNG ELECTRONIC (HK) INTERNATONAL GROUP COMPANY LIMITED Factory Address Room 1508, 15/F, Office Tower II, Grand Plaza, 625 Nathan Road, Kowloon, Hong Kong Product Designation Two Way Radio Brand Name BAOFENG, POFUNG, ALERVITES Test Model AT2 Series Model AT2 PRO Declaration of Difference Except for the model name and brand name, everything else is same. EUT Voltage DC3.7 V Applicable Standard IEEE Std. 1528:2013 FCC 47 CFR Part 2§2.1093 IEEE Std C95.1 ™-2019 Date of receipt of test item Dec. 10, 2026 Test Date Jan. 06, 2026 Report Template AGCRT- US -PTT/SAR (2021-04-20) Note: The results of testing in this report apply to the product/system which was tested only. Prepared By Bibo Zhang (Project Engineer) Apr. 02, 2026 Reviewed By Jack Gui (Reviewer) Apr. 02, 2026 Approved By Angela Li (Authorized Officer) Apr. 02, 2026 Report No.: AGC02294251205FH01 Page 4 of 43 TABLE OF CONTENTS 1. SUMMARY OF MAXIMUM SAR VALUE ......................................................................................................... 5 2. GENERAL INFORMATION ............................................................................................................................... 6 2.1. EUT DESCRIPTION......................................................................................................................................... 6 3. SAR MEASUREMENT SYSTEM ........................................................................................................................ 7 3.1. THE DASY5 SYSTEM USED FOR PERFORMING COMPLIANCE TESTS CONSISTS OF FOLLOWING ITEMS .................... 7 3.2. DASY5 E-FIELD PROBE ................................................................................................................................. 8 3.3. DATA ACQUISITION ELECTRONICS DESCRIPTION ............................................................................................... 8 3.4. ROBOT .......................................................................................................................................................... 9 3.5. LIGHT BEAM UNIT .......................................................................................................................................... 9 3.6. DEVICE HOLDER .......................................................................................................................................... 10 3.7. MEASUREMENT SERVER ............................................................................................................................... 10 3.8. PHANTOM ................................................................................................................................................. 11 4. SAR MEASUREMENT PROCEDURE ............................................................................................................ 12 4.1. SPECIFIC ABSORPTION RATE (SAR) .............................................................................................................. 12 4.2. SAR MEASUREMENT PROCEDURE ................................................................................................................ 13 5. TISSUE SIMULATING LIQUID ....................................................................................................................... 15 5.1. THE COMPOSITION OF THE TISSUE SIMULATING LIQUID..................................................................................... 15 5.2. TISSUE DIELECTRIC PARAMETERS FOR HEAD AND BODY PHANTOMS ............................................................... 15 5.3. TISSUE CALIBRATION RESULT ....................................................................................................................... 16 6. SAR SYSTEM CHECK PROCEDURE ........................................................................................................... 17 6.1. SAR SYSTEM CHECK PROCEDURES ............................................................................................................. 17 6.2. SAR SYSTEM CHECK ................................................................................................................................... 18 7. EUT TEST POSITION ...................................................................................................................................... 19 7.1. BODY WORN POSITION ................................................................................................................................ 19 8. SAR EXPOSURE LIMITS ............................................................................................................................... 20 9. TEST FACILITY .............................................................................................................................................. 21 10. TEST EQUIPMENT LIST ...................................................................................................…

Text truncated - open the document above for the full version.

Page 1 of 18 CALIBRATION DATA PROBE CALIBRATION DATA Page 2 of 18 Page 3 of 18 Page 4 of 18 Page 5 of 18 Page 6 of 18 Page 7 of 18 Page 8 of 18 Page 9 of 18 Page 10 of 18 DAE CALIBRATION DATA Page 11 of 18 Page 12 of 18 Page 13 of 18 DIPOLE CALIBRATION DATA Page 14 of 18 Page 15 of 18 Page 16 of 18 Page 17 of 18 Page 18 of 18

1、规格 报告主要提供BT\WIFI天线的无源性能参数的测试。 2、电器性 2-1规格标准 WIFI天线工作频段为 2400MHz-2500MHz 在此频段产生谐振。下表是海磁通为设计L5-WIFI 天线的量产性能测试指标. 天线 频率 (MHz) VSWR WIFI /BT 2400-2500 ≤ 2.0 2-2天线的匹配电路 无匹配 3、驻波比（VSWR）的测试 3-1 测试的设置 VSWR 测试装置依次的连接为：E5071B网络分析仪 → 50欧姆的同轴Cable→170mm长的铜管→ 测试治具。 测试治具的处理：从手机PCB上天线50欧姆测试点处用一根硬质电缆引出SMA-J接头，与套有 扼流圈的铜管连接，再依次连接其他装置。 3-2测试结果 Specification The report focuses on the passive performance parameters of BT\WIFI antennas. Electrical Specification standards The WIFI antenna operates in the 2400MHz-2500MHz frequency band and resonates in this band. The following table shows the production performance of L5-WIFI antenna designed by Magnetron. Ant Matching circuit for antenna NC Testing of VSWR Test setup E5071B → 50Cable→170mm DU T → Model:N/A Ant Type:PCB Antenna 4 有源测试的设置 有源测试装置依次的连接为：Agilent E5062A → 50欧姆的同轴Cable→EST远场测试系统→待 测试手机。 4-1 测试的场地 海磁通采用国内最先进的 3D/2D ETS 微波暗室测试系统，测试方式属于远场测试，频率范 围为 600MHz—6GHz，暗室屏蔽衰减在-120dBm， 4-2 测试结果 2400MHz Gain:2.17dBi Efficiency: 44.68% 2410MHz Gain:2.45dBi Efficiency: 41.70% Agilent E5062A → 50Cable→EST → DU T 2420MHz Gain:2.61dBi Efficiency: 41.56% 2430MHz Gain:2.8dBi Efficiency: 46.70% 2440MHz Gain:2.93dBi Efficiency: 46.34% 2450MHz Gain:3.24dBi Efficiency: 44.88% 2460MHz Gain:3.18dBi Efficiency: 46.96% 2470MHz Gain:2.95dBi Efficiency: 46.37% 2480MHz Gain:2.84dBi Efficiency: 45.51% 2490MHz Gain:2.71dBi Efficiency: 47.79% 2500MHz Gain:2.41dBi Efficiency:44.69% 天线尺寸 Size PAL1801 PAL1802 COL18

Page 1 of 70 FCC Test Report FCC ID : 2AJGM-AT2 APPLICATION PURPOSE : Original Equipment PRODUCT DESIGNATION : Two Way Radio BRAND NAME : BAOFENG, POFUNG, ALERVITES MODEL NAME : AT2, AT2 PRO APPLICANT : PO FUNG ELECTRONIC (HK) INTERNATONAL GROUP COMPANY LIMITED DATE OF ISSUE : Mar. 25, 2026 STANDARD(S) : FCC Part 15 Subpart C §15.247 REPORT VERSION : V1.0 Attestation Of Global Compliance (Shenzhen) Co., Ltd Report No.: AGC02294251205FR02 Report No.: AGC02294251205FR02 Page 2 of 70 Report Revise Record Report Version Revise Time Issued Date Valid Version Notes V1.0 / Mar. 25, 2026 Valid Initial Release Report No.: AGC02294251205FR02 Page 3 of 70 Table of Contents 1. General Information ........................................................................................................................................ 5 2. Product Information ........................................................................................................................................ 6 2.1 Product Technical Description ................................................................................................................... 6 2.2 Test Frequency List ................................................................................................................................... 6 2.3 Related Submittal(S) / Grant (S) ............................................................................................................... 7 2.4 Test Methodology ...................................................................................................................................... 7 2.5 Special Accessories .................................................................................................................................. 7 2.6 Equipment Modifications ........................................................................................................................... 7 2.7 Antenna Requirement................................................................................................................................ 7 3. Test Environment ............................................................................................................................................ 8 3.1 Address of the Test Laboratory ................................................................................................................. 8 3.2 Test Facility ................................................................................................................................................ 8 3.3 Environmental Conditions ......................................................................................................................... 9 3.4 Measurement Uncertainty ......................................................................................................................... 9 3.5 List of Equipment Use ............................................................................................................................. 10 4.System Test Configuration ............................................................................................................................ 12 4.1 EUT Configuration ................................................................................................................................... 12 4.2 EUT Exercise ........................................................................................................................................... 12 4.3 Configuration of Tested System .............................................................................................................. 12 4.4 Equipment Used In Tested System ........................................................................................................ 13 4.5 Summary of Test Results ........................................................................................................................ 14 5. Description of Test Modes ........................................................................................................................... 15 6. Duty Cycle Measurement ............................................................................................................................. 17 7. RF Output Power Measurement .................................................................................................................. 18 7.1 Provisions Applicable .............................................................................................................................. 18 7.2 Measurement Procedure ......................................................................................................................... 18 7.3 Measurement Setup (Block Diagram of Configuration) .......................................................................... 18 7.4 Measurement Result ............................................................................................................................... 19 8. 6dB Bandwidth Measurement ...................................................................................................................... 23 8.1 Provisions Applicable .............................................................................................................................. 23 8.2 Measurement Procedure ......................................................................................................................... 23 8.…

Text truncated - open the document above for the full version.