2AKAIHNDC101Digital Calendar

FCC Caution This device complies with part 15 of the FCC Rules. Operation is subject to the following two conditions: (1) This device may not cause harmful interference, and (2) this device must accept any interference received, including interference that may cause undesired operation. Any Changes or modifications not expressly approved by the party responsible for compliance could void the user's authority to operate the equipment. Note: This equipment has been tested and found to comply with the limits for a Class B digital device, pursuant to part 15 of the FCC Rules. These limits are designed to provide reasonable protection against harmful interference in a residential installation. This equipment generates uses and can radiate radio frequency energy and, if not installed and used in accordance with the instructions, may cause harmful interference to radio communications. However, there is no guarantee that interference will not occur in a particular installation. If this equipment does cause harmful interference to radio or television reception, which can be determined by turning the equipment off and on, the user is encouraged to try to correct the interference by one or more of the following measures: -Reorient or relocate the receiving antenna. -Increase the separation between the equipment and receiver. -Connect the equipment into an outlet on a circuit different from that to which the receiver is connected. -Consult the dealer or an experienced radio/TV technician for help. This equipment complies with FCC radiation exposure limits set forth for an uncontrolled environment. This equipment should be installed and operated with minimum distance 20 cm between the radiator & your body.

Rev 1/26/2023 SHENZHEN HARMONY INDUSTRIAL CO., LTD Federal Communications Commission Authorization and Evaluation Division 7435 Oakland Mills Road Columbia, MD 21046 USA Date: 2026-04-07 FCC ID: 2AKAIHNDC101 Ref. #1: Attestation Statements Part 2.911(d)(5)(i) Filing SHENZHEN HARMONY INDUSTRIAL CO., LTD certifies that the equipment for which authorization is sought is not “covered” equipment prohibited from receiving an equipment authorization pursuant to section 2.903 of the FCC rules. SHENZHEN HARMONY INDUSTRIAL CO., LTD certifies that the equipment for which authorization is sought does not include cybersecurity or anti-virus software produced or provided by Kaspersky Lab, Inc. or any of its successors and assignees, including equipment with integrated Kaspersky Lab, Inc. (or any of its successors and assignees) cybersecurity or anti-virus software pursuant to DA-24-886 and KDB 986446 D01 Covered Equipment Guidance section B(2a). Device is inherently compliant based on hardware limitations or software controls. or A Software Bill of Materials (SBOM) is provided to the TCB for review, and The end-user or third parties cannot install additional software on this device. Ref. #2: Attestation Statements Part 2.911(d)(5)(ii) Filing SHENZHEN HARMONY INDUSTRIAL CO., LTD certifies that, as of the date of the filing of the application, the applicant is not identified on the Covered List (as a specifically named entity or any of its subsidiaries or affiliates) as an entity producing “covered” equipment. Applicant: SHENZHEN HARMONY INDUSTRIAL CO., LTD Address: BLOCK 2,JIAYUAN INDUSTRIAL ZONE,HEPING COMMUNITY HIGH-TECH PARK,NO 2 FUYUANROAD,FUYONG,BAO’AN, SHENZHEN,China Contact Person: Xiaojun Zhou Tel.: +8613714192468 Email: [email protected] Sincerely, Signature:

SHENZHEN HARMONY INDUSTRIAL CO., LTD Office of Engineering Technology Federal Communications Commission 7435 Oakland Mills Road Columbia, MD 21046 USA Date: April 9, 2026 Subject; Request for Confidentiality FCC ID: 2AKAIHNDC101 To Whom It May Concern, Pursuant to the provisions of the Commission’s rules Title 47 Sections §0.457 and §0.459, we are requesting the Commission to withhold the following attachment(s) as confidential documents from public disclosure indefinitely. These documents contain detailed system and equipment descriptions and are considered as proprietary information in operation of the equipment. The public disclosure of these documents might be harmful to our company and would give competitors an unfair advantage in the market. Schematic Diagram Block Diagram Parts List Operational Description Tune-up Procedure SOFTWARE SECURITY REQUIREMENTS FOR U-NII DEVICES In additional to above mentioned documents, in order to comply with the marketing regulations in Title 47 CFR §2.803 and the importation rules in Title 47 CFR §2.1204, while ensuring that business sensitive information remains confidential until the actual marketing of newly authorized devices, we request Short Term Confidentiality of the following attachment(s); External Photos Test Setup Photos Internal Photos User Manual For 45 days, pursuant to Public Notice DA 04-1705. OR For 180 days pursuant to KDB 726920 D01. It is our understanding that all measurement test reports, FCC ID label format and correspondence during the certification review process cannot be granted as confidential documents and this information will be available for public review once the grant of equipment authorization is issued. Sincerely, Signature: Name: Xiaojun Zhou Title: CEO

Effective Date: April 2, 2020 QSF 7.6.4-8 – Agent Authorization Letter Template Page 1 of 1 Revision Date: Revision: 0 SHENZHEN HARMONY INDUSTRIAL CO., LTD Date：2026-04-07 Product Model Number: HN-DC1013, DC02, HN-DC1015, HN-DC1016, HN-DC1017 FCC ID：2AKAIHNDC101 To whom it may concern, Re: Product Certification Representative Authorization Letter We authorize QAI Laboratories Ltd. 3980 North Fraser Way, Burnaby B.C. Canada V5J 5K5 to act on our behalf on all matters concerning the above named equipment. This shall include the following: • Testing • Approval applications and procedures We declare that QAI Laboratories Ltd. is allowed to forward all information related to the approval project to the applied certification body and to the notification entities and to discuss any issues concerning the approval application. Any and all acts carried out by QAI Laboratories Ltd. on our behalf shall have the same effect as acts of our own. Signature: By: Xiaojun Zhou Contact Listed on FCC Wesbite Title: CEO Email: [email protected] On behalf of: SHENZHEN HARMONY INDUSTRIAL CO., LTD

SHENZHEN HARMONY INDUSTRIAL CO., LTD Declaration Letter of Model Difference Date: 2026-04-07 FCC ID: 2AKAIHNDC101 Tested Model Number: HN-DC1013 Adding Model Number(s): DC02, HN-DC1015, HN-DC1016, HN-DC1017 All Adding Model Number(s) is/are same electrically identical as Tested Model Number. Only the model and appearance color are different, everything else is the same. Yours Sincerely, Applicant: SHENZHEN HARMONY INDUSTRIAL CO., LTD Address: BLOCK 2,JIAYUAN INDUSTRIAL ZONE,HEPING COMMUNITY HIGH-TECH PARK,NO 2 FUYUANROAD,FUYONG,BAO’AN, SHENZHEN,China Contact Person: Xiaojun Zhou Tel.: +8613714192468 Email: [email protected] Sincerely, Signature:

Page 1 of 5 Report No.: LGT26C204 Appendix - External Photographs of EUT Constructional Details Photo 1 Photo 2 Page 2 of 5 Report No.: LGT26C204 Appendix - External Photographs of EUT Constructional Details Photo 3 Photo 4 Page 3 of 5 Report No.: LGT26C204 Appendix - External Photographs of EUT Constructional Details Photo 5 Photo 6 Page 4 of 5 Report No.: LGT26C204 Appendix - External Photographs of EUT Constructional Details Photo 7 Photo 8 Page 5 of 5 Report No.: LGT26C204 Appendix - External Photographs of EUT Constructional Details Photo 9

Label Size: 24*51mm

Page 1 of 4 Report No.: LGT26C204 Appendix - Internal Photographs of EUT Constructional Details Photo 1 Photo 2 Page 2 of 4 Report No.: LGT26C204 Appendix - Internal Photographs of EUT Constructional Details Photo 3 Photo 4 Page 3 of 4 Report No.: LGT26C204 Appendix - Internal Photographs of EUT Constructional Details Photo 5 Photo 6 Wi-Fi ANT Page 4 of 4 Report No.: LGT26C204 Appendix - Internal Photographs of EUT Constructional Details Photo 7 Photo 8

The test report is effective only with both signature and specialized stamp. This report shall not be reproduced except in full without the written approval of the Laboratory. The results in this report only apply to the tested sample. Shenzhen LGT Test Service Co., Ltd. Tel: 0755-89668180 E-mail:[email protected] Web: www.lgt-cert.com Room 205, Building 13, Zone B, Zhenxiong Industrial Park, No.177, Renmin West Road, Jinsha, Kengzi Street, Pingshan District, Shenzhen, Guangdong, China Page 1 of 8 EMF TEST REPORT Product Name: Digital Calendar Model Number: HN-DC1013, DC02, HN-DC1015, HN-DC1016, HN- DC1017 FCC ID: 2AKAIHNDC101 Issued For : SHENZHEN HARMONY INDUSTRIAL CO., LTD BLOCK 2,JIAYUAN INDUSTRIAL ZONE,HEPING COMMUNITY HIGH-TECH PARK,NO 2 FUYUANROAD,FUYONG,BAO'AN, SHENZHEN,China Issued By : Shenzhen LGT Test Service Co., Ltd. Room 205, Building 13, Zone B, Zhenxiong Industrial Park, No.177, Renmin West Road, Jinsha, Kengzi Street, Pingshan District, Shenzhen, Guangdong, China Report Number: LGT26C204HA01 Sample Received Date: Mar. 25, 2026 Date of Test: Mar. 25, 2026 ~ Apr. 03, 2026 Date of Issue: Apr. 03, 2026 Report No.: LGT26C204HA01 Page 2 of 8 TEST REPORT CERTIFICATION Applicant: SHENZHEN HARMONY INDUSTRIAL CO., LTD Address: BLOCK 2,JIAYUAN INDUSTRIAL ZONE,HEPING COMMUNITY HIGH-TECH PARK,NO 2 FUYUANROAD,FUYONG,BAO'AN, SHENZHEN,China Manufacturer: SHENZHEN HARMONY INDUSTRIAL CO., LTD Address: BLOCK 2,JIAYUAN INDUSTRIAL ZONE,HEPING COMMUNITY HIGH-TECH PARK,NO 2 FUYUANROAD,FUYONG,BAO'AN, SHENZHEN,China Product Name: Digital Calendar Trademark: N/A Model Number: HN-DC1013, DC02, HN-DC1015, HN-DC1016, HN-DC1017 Sample Status: Normal APPLICABLE STANDARDS STANDARD TEST RESULTS FCC 47 CFR §2.1091 KDB 447498 D01 General RF Exposure Guidance v06 PASS Prepared by: Approved by: Zane Shan Vita Li Engineer Technical Director Report No.: LGT26C204HA01 Page 3 of 8 TABLE OF CONTENTS 1 . GENERAL INFORMATION 5 1.1 GENERAL DESCRIPTION OF THE EUT 5 1.2 TEST LABORATORY 5 2 . FCC 47CFR §2.1091 REQUIREMENT 6 2.1 TEST STANDARDS 6 2.2 LIMIT 6 2.3 EUT OPERATION CONDITION 7 2.4 CLASSIFICATION 7 2.5 TEST RESULT 8 Report No.: LGT26C204HA01 Page 4 of 8 Revision History Rev. Issue Date Revisions 00 Apr. 03, 2026 Initial Issue Report No.: LGT26C204HA01 Page 5 of 8 1. GENERAL INFORMATION 1.1 GENERAL DESCRIPTION OF THE EUT Product Name: Digital Calendar Test Model Number: HN-DC1013 Series Number: DC02, HN-DC1015, HN-DC1016, HN-DC1017 Model Difference: Only the model and appearance color are different, everything else is the same. Frequency Bands: 2.4G WLAN 802.11b/g/n(20MHz): 2412~2462MHz Adapter: Input: 100-240V 50/60Hz 0.3A Output: 5.0V 2.0A Hardware Version: Q606_V05 Software Version: Android 11 1.2 TEST LABORATORY Company Name: Shenzhen LGT Test Service Co., Ltd. Address: Room 205, Building 13, Zone B, Zhenxiong Industrial Park, No.177, Renmin West Road, Jinsha, Kengzi Street, Pingshan District, Shenzhen, Guangdong, China Accreditation Certificate: FCC Registration No.: 746540 CAB ID: CN0136 Report No.: LGT26C204HA01 Page 6 of 8 2. FCC 47CFR §2.1091 REQUIREMENT 2.1 TEST STANDARDS The limit for Maximum Permissible Exposure (MPE) specified in FCC 1.1310 is followed. The gain of the antennas used in the product is extracted from the Antenna data sheets provided and also the maximum total power input to the antenna is measured. Through the Friis transmission formula and the maximum gain of the antenna, we can calculate the distance, away from the product, where the limit of MPE is reached. Although the Friis Transmission formula is far field assumption, the calculated result of that is an over-prediction for near field power density. It is taken as worst case to specify the safety range. 2.2 LIMIT According to FCC 1.1310: The criteria listed in the following table shall be used to evaluate the environmental impact of the human exposure to radio-frequency (RF) radiation as specified in 1.1307 (b) Limits for Maximum Permissible Exposure (MPE) Frequency Range (MHz) Electric Field Strength (V/m) Magnetic Field Strength (A/m) Power Density (mW/cm²) Limits for Occupational / controlled Exposures 0.3-3.0 614 1.63 *(100) 3.0-30 1842/f 4.89/f *(900/f 2 ) 30-300 61.4 0.163 1.0 300 - 1500 -- -- F/300 1500 – 100000 -- -- 5.0 Limits for General population / Uncontrolled Exposure 0.3-1.34 614 1.63 *(100) 1.34-30 824/f 2.19/f *(180/f 2 ) 30-300 27.5 0.073 0.2 300 - 1500 -- -- F/1500 1500 – 100000 -- -- 1.0 F= Frequency in MHz * = Plane-wave equivalent power density. Friss Formula Friss Transmission Formula: Pd = (Pout * G) / (4*pi*r²) Where Pd = power density in mW/cm² Pout = output power to antenna in mW G = gain of antenna in linear scale Pi = 3.1416 R = Distance between observation point and the center of radiator in cm If we know the maximum gain of the antenna and the total output power to the antenna, through calculation, we will know MPE value at distance 20cm. Report No.: LGT26C204HA01 Page 7 of 8 2.3 EUT OPERATION CONDITION EUT was enabled to transmit and receive at lowest, middle and highest channels. 2.4 CLASSIFICATION The antenna of this product, under normal use condition, is at least 20cm away from the body of the user. Warning statement to the user for keeping at least 20cm or more separation distance from the antenna should be included in the User manual. So, this device is classified as Mobile device. Report No.: LGT26C204HA01 Page 8 of 8 2.5 TEST RESULT Turn up Result Mode Turn up Power 2.4G WIFI-802.11b 16±1dBm 2.4G WIFI-802.11g 14±1dBm 2.4G WIFI-802.11n(HT20) 14±1dBm The MPE result of worst mode: RF Function Max Turn up Power (dBm) Max Turn up Power (mW) ANT Gain (dBi) ANT Gain (gain of antenna in linear scale) Power Density (mW/cm²) Limit (mW/cm²) Ratio Result 2.4G WIFI 17.00 50.12 1.37 1.37 0.014 1 0.014 Pass Note: 1. The RF Exposure is less than the limit, complies with the exemption requirements. ※※※※※END OF THE REPORT※※※※※

深圳市顺达成科技有限公司 SH UN DA CHENGTECHNOLOGYCO., LTD 公司 地址： 深圳市宝安区福永镇重庆路新福工业园B5栋4 楼 Tel:0755-27211658Fax:0755-29485750 承认书 SPECIFICATIONFOR APPROVAL 审批/ Approval客户批准/CustomerApproval 制作 PreparedBy 审核 CheckedBy 批准 ApprovalBy 审核 CheckedBy 批准 ApprovalBy 签章 Signature 日期 Date 2026.03.102026.03.102026.03.10 修订履历/ChangeLog 版本 Version 修订内容 ChangeDescription 责任人 Personin Charge 核准 ApprovalBy 日期 Date 客户名称 CustomerName 客户项目名Customer ProjectName HN-DC1013 顺达成项目名 SDC ProjectName HN-DC1013 客户编码 CustomerP/N 顺达成料号 SDCP/N WF714B-1131L-65 频段 Band WIFI2.4G天线丝印：SDCF543AWF 版本号 Version A0 设计人信息/DesignerInformation 射频工程师 RF Engineer 研发主管 R&D Diretor 结构工程师 ME Engineer Company Address: 4th Floor, Building B5, Xinfu Industrial Park, Chongqing Road, Fuyong Town, Bao 'an District, Shenzhen 深圳市顺达成科技有限公司 SH UN DA CHENGTECHNOLOGYCO., LTD 产品图纸或实物图片 Drawingor ProductImage 李瑶娜 WF714B-1131L-65 HN-DC1013 X.X ±0.5 X.XX ±0.2 XXX. ±10.0 XX. ±5.0 X. ±2.0 1 65 SDC F543A WF   1  深圳市顺达成科技有限公司 SH UN DA CHENGTECHNOLOGYCO., LTD 射频性能测量报告 RF PerformanceTestReport 天线测试设备简介 AntennaTestEquipmentIntroduction 测试天线输入特性使用AgilentE5071CandAgilent5062A矢量网络分析仪；辐射特性利 用广屏三维近场暗室进行测试，并分别使用8960E5515和 AgilentE4438C进行了分析。暗房的测 试坐标如下: Testof antennainputcharacteristicsusingAgilentE5071C and Agilent5062Avectornetwork analyzer;The radiationpatternof the antennaare testedusingthe guangping3D nearfieldAnechoicChamber, and the instrumentis usedto agilent8960E5515and AgilentE4438C. The testcoordinatesof the darkroom areas follows: 1.S11参数测量/S11Parameter-VSWR 使用一根50 Ω同轴电缆连接到天线，然后该电缆连接到网络分析仪测量S11 参数，被测量产品远离金属至少 20 厘米。 MeasuringMethodis a 50Ωcoaxialcableis connectedto theantenna. Thenthiscableis connectedto a networkanalyzer to measuretheS11parameter,Keepingthisfixtureawayfrommetalat least20cm. 深圳市顺达成科技有限公司 SH UN DA CHENGTECHNOLOGYCO., LTD S11 Parameter-VSWR 2.天线匹配网络/ AntennaMatchingNetwork 深圳市顺达成科技有限公司 SHUNDACHENGTECHNOLOGYCO.,LTD 公司地址： 深圳市宝安区福永镇重庆路新福工业园B5栋4楼电话:0755-27211658传真:0755-29485750 3.Gain&Efficiency

The test report is effective only with both signature and specialized stamp. This report shall not be reproduced except in full without the written approval of the Laboratory. The results in this report only apply to the tested sample. Shenzhen LGT Test Service Co., Ltd. Tel: 0755-89668180 E-mail:[email protected] Web: www.lgt-cert.com Room 205, Building 13, Zone B, Zhenxiong Industrial Park, No.177, Renmin West Road, Jinsha, Kengzi Street, Pingshan District, Shenzhen, Guangdong, China Page 1 of 62 RF TEST REPORT Product Name: Digital Calendar Model Number: HN-DC1013, DC02, HN-DC1015, HN-DC1016, HN-DC1017 FCC ID: 2AKAIHNDC101 Issued For : SHENZHEN HARMONY INDUSTRIAL CO., LTD BLOCK 2,JIAYUAN INDUSTRIAL ZONE,HEPING COMMUNITY HIGH-TECH PARK,NO 2 FUYUANROAD,FUYONG,BAO'AN, SHENZHEN,China Issued By : Shenzhen LGT Test Service Co., Ltd. Room 205, Building 13, Zone B, Zhenxiong Industrial Park, No.177, Renmin West Road, Jinsha, Kengzi Street, Pingshan District, Shenzhen, Guangdong, China Report Number: LGT26C204RF01 Sample Received Date: Mar. 25, 2026 Date of Test: Mar. 25, 2026 ~ Apr. 03, 2026 Date of Issue: Apr. 03, 2026 Report No.: LGT26C204RF01 Page 2 of 62 TEST REPORT CERTIFICATION Applicant: SHENZHEN HARMONY INDUSTRIAL CO., LTD Address: BLOCK 2,JIAYUAN INDUSTRIAL ZONE,HEPING COMMUNITY HIGH-TECH PARK,NO 2 FUYUANROAD,FUYONG,BAO'AN, SHENZHEN,China Manufacturer: SHENZHEN HARMONY INDUSTRIAL CO., LTD Address: BLOCK 2,JIAYUAN INDUSTRIAL ZONE,HEPING COMMUNITY HIGH-TECH PARK,NO 2 FUYUANROAD,FUYONG,BAO'AN, SHENZHEN,China Product Name: Digital Calendar Trademark: N/A Model Number: HN-DC1013, DC02, HN-DC1015, HN-DC1016, HN-DC1017 Sample Status: Normal APPLICABLE STANDARDS STANDARD TEST RESULTS FCC Part 15.247, Subpart C ANSI C63.10-2020 PASS Prepared by: Approved by: Zane Shan Vita Li Engineer Technical Director Report No.: LGT26C204RF01 Page 3 of 62 Table of Contents Page 1. SUMMARY OF TEST RESULTS 6 1.1 TEST LABORATORY 7 1.2 MEASUREMENT UNCERTAINTY 7 2. GENERAL INFORMATION 8 2.1 GENERAL DESCRIPTION OF THE EUT 8 2.2 DESCRIPTION OF THE TEST MODES 10 2.3 TEST SOFTWARE AND POWER LEVEL 10 2.4 DESCRIPTION OF NECESSARY ACCESSORIES AND SUPPORT UNITS 11 2.5 EQUIPMENTS LIST FOR ALL TEST ITEMS 12 3. EMC EMISSION TEST 14 3.1 CONDUCTED EMISSION MEASUREMENT 14 3.2 RADIATED EMISSION MEASUREMENT 18 4. CONDUCTED SPURIOUS & BAND EDGE EMISSION 28 4.1 LIMIT 28 4.2 TEST PROCEDURE 28 4.3 DEVIATION FROM STANDARD 28 4.4 TEST SETUP 28 4.5 EUT OPERATION CONDITIONS 28 4.6 TEST RESULTS 28 5. POWER SPECTRAL DENSITY TEST 29 5.1 LIMIT 29 5.2 TEST PROCEDURE 29 5.3 DEVIATION FROM STANDARD 29 5.4 TEST SETUP 29 5.5 EUT OPERATION CONDITIONS 29 5.6 TEST RESULTS 29 6. BANDWIDTH TEST 30 6.1 LIMIT 30 6.2 TEST PROCEDURE 30 6.3 DEVIATION FROM STANDARD 30 6.4 TEST SETUP 30 6.5 EUT OPERATION CONDITIONS 30 6.6 TEST RESULTS 30 Report No.: LGT26C204RF01 Page 4 of 62 7. PEAK OUTPUT POWER TEST 31 7.1 LIMIT 31 7.2 TEST PROCEDURE 31 7.3 DEVIATION FROM STANDARD 31 7.4 TEST SETUP 31 7.5 EUT OPERATION CONDITIONS 31 7.6 TEST RESULTS 31 8. ANTENNA REQUIREMENT 32 8.1 STANDARD REQUIREMENT 32 8.2 EUT ANTENNA 32 APPENDIX I - TEST RESULTS 33 DUTY CYCLE 33 MAXIMUM PEAK CONDUCTED OUTPUT POWER 37 -6DB BANDWIDTH 38 OCCUPIED CHANNEL BANDWIDTH 42 MAXIMUM POWER SPECTRAL DENSITY LEVEL 46 BAND EDGE 50 CONDUCTED RF SPURIOUS EMISSION 55 APPENDIX II - MEASUREMENT PHOTOS 62 Report No.: LGT26C204RF01 Page 5 of 62 Revision History Rev. Issue Date Revisions 00 Apr. 03, 2026 Initial Issue Report No.: LGT26C204RF01 Page 6 of 62 1. SUMMARY OF TEST RESULTS Test procedures according to the technical standards: KDB 558074 D01 15.247 Meas Guidance v05r02. FCC Part 15.247,Subpart C Standard Section Test Item Judgment Remark 15.207 Conducted Emission PASS -- 15.247 (a)(2) 6dB Bandwidth PASS -- 15.247 (b)(3) Output Power PASS -- 15.209 Radiated Spurious Emission PASS -- 15.247 (d) Conducted Spurious & Band Edge Emission PASS -- 15.247 (e) Power Spectral Density PASS -- 15.205 Restricted Band Edge Emission PASS -- Part 15.247(d)/ Part 15.209(a) Band Edge Emission PASS -- 15.203 Antenna Requirement PASS -- NOTE: (1) ‘N/A’ denotes test is not applicable in this Test Report. (2) All tests are according to ANSI C63.10-2020. Report No.: LGT26C204RF01 Page 7 of 62 1.1 TEST LABORATORY Company Name: Shenzhen LGT Test Service Co., Ltd. Address: Room 205, Building 13, Zone B, Zhenxiong Industrial Park, No.177, Renmin West Road, Jinsha, Kengzi Street, Pingshan District, Shenzhen, Guangdong, China Accreditation Certificate: FCC Registration No.: 746540 CAB ID: CN0136 1.2 MEASUREMENT UNCERTAINTY The reported uncertainty of measurement y ± U, where expended uncertainty U is based on a standard uncertainty multiplied by a coverage factor of k=2, providing a level of confidence of approximately 95 %. Occupied Channel Bandwidth ±0.46% RF Output Power, Conducted ±0.71dB Power Spectral Density, Conducted ±1.57dB Unwanted Emission, Conducted ±0.63dB Conducted emission ±2.80dB All Emissions, Radiated (0.009-30MHz) ±2.16dB All Emissions, Radiated (30MHz-1GHz) ±4.61dB All Emissions, Radiated (1GHz-18GHz) ±5.49dB Temperature ±0.5°C Humidity ±2% Duty Cycle ±2.3% Note: The measurement uncertainty is not included in the test result. Report No.: LGT26C204RF01 Page 8 of 62 2. GENERAL INFORMATION 2.1 GENERAL DESCRIPTION OF THE EUT Product Name: Digital Calendar Test Model Number: HN-DC1013 Series Number: DC02, HN-DC1015, HN-DC1016, HN-DC1017 Model Difference: Only the model and appearance color are different, everything else is the same. Product Description: Operation Frequency: 802.11b/g/n(20MHz): 2412~2462MHz Modulation Type: 802.11b(DSSS):CCK,DQPSK,DBPSK 802.11g(OFDM):BPSK,QPSK,16-QAM,64-QAM 802.11n(OFDM):BPSK,QPSK,16-QAM,64-QAM Number of Channel: 802.11b/g/n(20MHz): 11CH Antenna Designation: FPC Antenna Antenna Gain(dBi): 1.37 Channel List: Please refer to the Note 3. Adapter: Input: 100-240V 50/60Hz 0.3A Output: 5.0V 2.0A Hardware Version: Q606_V05 Software Version: Android 11 Connecting I/O Port(s): Please ref…

Text truncated - open the document above for the full version.

Page 1 of 2 Report No.: LGT26C204 Appendix - Test Setup photos Set-up for Radiated Spurious Emission, Below 1GHz Set-up for Radiated Spurious Emission, Above 1GHz Page 2 of 2 Report No.: LGT26C204 Set-up for Conducted Emission