2AKCZ-108Wireless Access Point

• SonicWall SonicWave 231c 1 Safety and Regulatory Information SonicWave 621 Safety and Regulatory Reference Guide Regulatory Model Number APL68-108 Products with “UL 2043” printed on their product labels are within the limit specified in the “UL 2043 Standard for Fire Test for Heat and Visible Smoke Release for Discrete Products Installed in Air‐Handling Spaces” (Plenum). Applies only when powered through PoE. The PoE power supply is not covered the by the UL 2043 evaluation of this Access Point. This document contains safety and regulatory information for the SonicWall SonicWave 621. The SonicWave 621 is a wireless access point with an internal wireless radio that can provide wireless access on either 5GHz or 2.4GHz and supports the 802.11 ax/ac/n/g/a/b standards. Topics: • Mounting the SonicWave 621 • Safety Information for Installation and Operation • Consignes de sécurité pour l'installation et l'utilisation • Sicherheitshinweise für den Einbau und Betrieb • 安装 SonicWave 621 • 安裝 SonicWave 621 • SonicWave 621 のインストール • SonicWave 621 설치 • Instalar o SonicWave 621 • Agency Specific Information • Electromagnetic Compatibility Information • EMC Agency Specific Information 2 Safety and Regulatory Information Mounting the SonicWave 621 Installing the Mounting Bracket The SonicWave 621 comes with a mounting bracket so it can be mounted on the ceiling or other flat surface. This section describes how to attach the mounting bracket to the ceiling or an indoor wall. The mounting bracket provides two pairs of T‐bar locking tabs that support two ceiling T‐bar widths: 15/16 inch and 9/16 inch. For mounting on a flat surface, holes in the T‐bar clips on the bracket provide insertion points for screws. Use #6 (3.5mm) zinc plated pan head machine screws (sheet metal screws) of length 1.25 inches (31.75 mm). When mounting on drywall, anchors should be used. Anchors must accommodate the screws and be rated to hold at least 10 lbs (4.5 kg). Mounting Bracket Top Mounting Bracket Bottom SonicWall 3 Safety and Regulatory Information To attach the mounting bracket to the ceiling using T-bar clips: 1 Press the top side of the mounting bracket against the ceiling tile T‐bar so that the T‐ bar locking tabs on the mounting bracket are depressed. 2 Rotate the mounting bracket until the ceiling T‐bar slides into the T‐bar clips on the mounting bracket and the T‐bar locking tabs click into place. T-Bar with Mounting Plate 4 Safety and Regulatory Information To attach the mounting bracket to the ceiling or to a wall using screws: 1 Place the top side of the mounting bracket against the ceiling or wall and mark the locations for the two screw insertion points. 2 Drill starter holes at the marked locations. For a wood wall, use a drill bit that fits the screws. For drywall, use a drill bit that fits the anchors. 3 For drywall, screw in the anchors. 4 Place the mounting bracket against the wall with the holes lined up on the marks or anchors. 5 Using the screws and a screwdriver, securely attach the mounting bracket to the ceiling or wall. Installing the SonicWave 621 This section describes how to connect the PoE and network cables and then attach the SonicWave 621 to the mounting bracket. The SonicWave 621 is powered by a power adapter (sold separately) or by Power over Ethernet (PoE). SonicWall recommends using CAT 5e cables to connect PoE to the access point. CAUTION: When using PoE to power the device, an 802.3at compliant PoE injector, PoE enabled switch, or SonicWall PoE enabled appliance is required to provide power to each SonicWave 621. To maintain power to the SonicWave 621, the maximum length of CAT 5e cable from the PoE device to the SonicWave 621 is 100 meters (333 feet). 1 Using an Ethernet cable, connect the Data in port on the PoE Injector or switch to an interface on your network device. If using a SonicWall firewall, connect it to an existing WLAN zone interface on the firewall or to an unused interface to be configured later in SonicOS. 2 Using a second Ethernet cable, connect the Data and Power Out port on the PoE injector to the LAN/POE port on your SonicWave 621. Refer to your PoE Installation Guide for more information. SonicWall 5 Safety and Regulatory Information 3 Plug the power cord of the PoE Injector into an appropriate power outlet. 4 Wait up to two minutes for the LAN LED on the SonicWave 621 to illuminate. This indicates an active connection. To attach the SonicWave 621 to the mounting bracket: 1 Line up the two mounting tab insert points on the back of the SonicWave 621 with the mounting tabs on the mounting bracket. 2 Insert the mounting tabs into the SonicWave 621 and slide the access point down until the locking tab on the bracket clicks into place on the SonicWave. Safety Information for Installation and Operation • Installation Requirements • RF Safety Distance • Cable Connections • Power Supply Information • Restricted Environments • Radio Approvals • Radio or Television Interference • Wireless Interoperability Products with “UL 2043” printed on their product labels are within the limit specified in the “UL 2043 Standard for Fire Test for Heat and Visible Smoke Release for Discrete Products Installed in Air‐Handling Spaces” (Plenum). Applies only when powered through PoE. The PoE power supply is not covered the by the UL 2043 evaluation of this Access Point. NOTE: Additional regulatory notifications and information for this product can be found online at: https://www.sonicwall.com/support/technical‐documentation SonicWave 621 complies with FCC U‐NII New Rules. Regulatory Model/Type Product Name APL68-108 SonicWave 621 6 Safety and Regulatory Information Installation Requirements WARNING: The following conditions are required for proper installation: 1 Mount in a location away from direct sunlight and sources of heat. A maximum ambient temperature of 104º F (40º C) is recommended. 2 Route cables away from power lines, fluorescent lighting fixtures, and sources of noise such as r…

Text truncated - open the document above for the full version.

1033 McCarthy Boulevard, Milpitas, California 95035 USA Office +1-888-557-6642 Date: 2022-07-26 FCC ID: 2AKCZ-108 AUTHORIZATION LETTER To Whom It May Concern: SonicWall Inc. hereby authorizes Andrea Hsia / Supervisor of Bureau Veritas Consumer Products Services (H.K.) Ltd., Taoyuan Branch (“BV CPS Taoyuan”), to act on its behalf in all matters relating to this Federal Communication Commission (“FCC”) application for equipment authorization in connection with the FCC ID listed above, including signing of all documents relating to these matters. Any and all acts carried out by Andrea Hsia / Supervisor of BV CPS Taoyuan on SonicWall Inc.’s behalf, within the scope of the powers granted herein, shall have the same effect as acts of its own. Authorization valid until 31DEC2022 If you have any questions regarding the authorization, please don’t hesitate to contact us. Sincerely yours, ----------------------------------- Rick Linford / Regulatory Engineer Telephone Number: +1408.962.8798 Fax Number: +1 408.962.8798 E-mail Address: [email protected]

1033 McCarthy Boulevard, Milpitas, California 95035 USA Office +1-888-557-6642 Date: 2022-07-26 FCC ID: 2AKCZ-108 To the attention of Federal Communications Commission Authorization and Evaluation Division Permanent Confidentiality Request Pursuant to Sections 0.457 and 0.459 of the Commission’s Rules, the Applicant hereby requests confidential treatment of information accompanying this Application as outlined below: Schematics Block Diagram Operational Description Software Operational Description The above materials contain trade secrets and proprietary information not customarily released to the public. The public disclosure of these matters might be harmful to the Applicant and provide unjustified benefits to its competitors. The Applicant understands that pursuant to Rule 0.457, disclosure of this Application and all accompanying documentation will not be made before the date of the Grant for this application. Sincerely yours, ----------------------------------- Rick Linford / Regulatory Engineer Telephone Number: +1408.962.8798 Fax Number: +1 408.962.8798 E-mail Address: [email protected]

1033 McCarthy Boulevard, Milpitas, California 95035 USA Office +1-888-557-6642 Date: July 26, 2022 We, SonicWall Inc. declare that the device does not support channel 12 ~ 13 in 2.4GHz band and any non-US channels in all the operational mode(s) for the following product. FCC ID: 2AKCZ-108 If you should have any question(s) regarding this declaration, please don’t hesitate to contact us. Sincerely yours, ----------------------------------- Rick Linford / Regulatory Engineer Telephone Number: +1408.962.8798 Fax Number: +1 408.962.8798 E-mail Address: [email protected]

Reference No.: BDYS-WTW-P22031091_FCC_EXT Page 1/9 CONSTRUCTION PHOTOS OF EUT Reference No.: BDYS-WTW-P22031091_FCC_EXT Page 2/9 Reference No.: BDYS-WTW-P22031091_FCC_EXT Page 3/9 Reference No.: BDYS-WTW-P22031091_FCC_EXT Page 4/9 Reference No.: BDYS-WTW-P22031091_FCC_EXT Page 5/9 Reference No.: BDYS-WTW-P22031091_FCC_EXT Page 6/9 Reference No.: BDYS-WTW-P22031091_FCC_EXT Page 7/9 Reference No.: BDYS-WTW-P22031091_FCC_EXT Page 8/9 Reference No.: BDYS-WTW-P22031091_FCC_EXT Page 9/9

R CCAJXXXXXXXXXX 電波法により5GHzは屋内使用に限ります 18B1691D9240 5AHW-UZC4 FCC ID: 2AKCZ-108 IC:22137-108 無線網路基地台 Made in Taiwan/台灣製造 台湾制造 C-18283 SONICWALL SONICWALL Serial Number: Authentication Code: Model/型號:APL68-108 CAN ICES-3 (B)/NMB-3(B) ASSY:101-500584-50 Rev. A LBL PN:341-000056-57 A www.sonicwall.com This device complies with Par t 15 of the FCC Rules. Operation is subject to the followingtwo conditions: 1)This device may not cause harmful interfer ence, and 2) this device must accept any interfer ence received, including interfer ence that may cause undesired operation. 10 产品型号: SonicWave 621 无线接入点 SonicWave 621 D3B337 RoHS XXX-XXXXXX SonicWall International Ltd. City Gate Park, Mahon,Cork,Ireland �� ����� �� � ���� ���� �� R-R-SWL-108 额定电压 : 制造商 : SonicWall Inc. 48-55V 额定电流 : 0.3A Adapter 额定电压 : 12V 额定电流 : 3.0A POE POE V/額定電壓: 48-55V A/額定電流: 0.3A Adapter V/額定電壓: 12V A/額定電流: 3.0A “Este equipamento não tem direito à proteção contra interferência prejudicial e não pode causar interferência em sistemas devidamente autorizados” [email protected] XXXXX-XX-XXXXX CMIIT ID:XXXXXXXXXX

FCC ID: 2AKCZ-108 The label will be permanently affixed and readily visible. Label location Bottom of EUT

Reference No.: BDYS-WTW-P22031091_FCC_INT Page 1/13 CONSTRUCTION PHOTOS OF EUT Reference No.: BDYS-WTW-P22031091_FCC_INT Page 2/13 Reference No.: BDYS-WTW-P22031091_FCC_INT Page 3/13 Reference No.: BDYS-WTW-P22031091_FCC_INT Page 4/13 Reference No.: BDYS-WTW-P22031091_FCC_INT Page 5/13 Reference No.: BDYS-WTW-P22031091_FCC_INT Page 6/13 Reference No.: BDYS-WTW-P22031091_FCC_INT Page 7/13 Reference No.: BDYS-WTW-P22031091_FCC_INT Page 8/13 Reference No.: BDYS-WTW-P22031091_FCC_INT Page 9/13 Reference No.: BDYS-WTW-P22031091_FCC_INT Page 10/13 Reference No.: BDYS-WTW-P22031091_FCC_INT Page 11/13 Reference No.: BDYS-WTW-P22031091_FCC_INT Page 12/13 Reference No.: BDYS-WTW-P22031091_FCC_INT Page 13/13

Report No.: MFBDYS-WTW-P22031091 Page No. 1 / 11 Report Format Version: 6.1.2 RF Exposure Report Report No.: MFBDYS-WTW-P22031091 FCC ID: 2AKCZ-108 Test Model: APL68-108 Received Date: Mar. 28, 2022 Test Date: Jul. 05, 2022 Issued Date: Aug. 09, 2022 Applicant: SonicWall Inc. Address: 1033 McCarthy Blvd., Milpitas, CA 95035, USA Issued By: Bureau Veritas Consumer Products Services (H.K.) Ltd., Taoyuan Branch Lin Kou Laboratories Lab Address: No. 47-2, 14th Ling, Chia Pau Vil., Lin Kou Dist., New Taipei City, Taiwan Test Location (1): No. 19, Hwa Ya 2nd Rd., Wen Hwa Vil., Kwei Shan Dist., Taoyuan City 33383, TAIWAN FCC Registration / Designation Number: 788550 / TW0003 Test Location (2): No. 70, Wenming Rd., Guishan Dist., Taoyuan City 333, Taiwan (R.O.C.) FCC Registration / Designation Number: 281270 / TW0032 This report is governed by, and incorporates by reference, the Conditions of Testing as posted at the date of issuance of this report at http://www.bureauveritas.com/home/about-us/our-business/cps/about-us/terms-conditions/ and is intended for your exclusive use. Any copying or replication of this report to or for any other person or entity, or use of our name or trademark, is permitted only with our prior written permission. This report sets forth our findings solely with respect to the test samples identified herein. The results set forth in this report are not indicative or representative of the quality or characteristics of the lot from which a test sample was taken or any similar or identical product unless specifically and expressly noted. Our report includes all of the tests requested by you and the results thereof based upon the information that you provided to us. Measurement uncertainty is only provided upon request for accredited tests. Statements of conformity are based on simple acceptance criteria without taking measurement uncertainty into account, unless otherwise requested in writing. You have 60 days from date of issuance of this report to notify us of any material error or omission caused by our negligence or if you require measurement uncertainty; provided, however, that such notice shall be in writing and shall specifically address the issue you wish to raise. A failure to raise such issue within the prescribed time shall constitute your unqualified acceptance of the completeness of this report, the tests conducted and the correctness of the report contents. Report No.: MFBDYS-WTW-P22031091 Page No. 2 / 11 Report Format Version: 6.1.2 Table of Contents Release Control Record .................................................................................................................................. 3 1 Certificate of Conformity ...................................................................................................................... 4 2 Applicable RF Exposure Limit ............................................................................................................. 5 3 Applicable Evaluation Criteria ............................................................................................................. 6 4 Test Setup .............................................................................................................................................. 7 5 Test Instruments ................................................................................................................................... 7 6 Test Result ............................................................................................................................................. 9 7 Conclusion ........................................................................................................................................... 11 Report No.: MFBDYS-WTW-P22031091 Page No. 3 / 11 Report Format Version: 6.1.2 Release Control Record Issue No. Description Date Issued MFBDYS-WTW-P22031091 Original Release Aug. 09, 2022 Report No.: MFBDYS-WTW-P22031091 Page No. 4 / 11 Report Format Version: 6.1.2 1 Certificate of Conformity Product: Wireless Access Point Brand: SONICWALL Test Model: APL68-108 Sample Status: Engineering sample Applicant: SonicWall Inc. Date of Evaluation: Jul. 05, 2022 FCC Rule Part: FCC Part 2 (Section 2.1091 & 2.1093) Standards: KDB 447498 D04 Interim General RF Exposure Guidance v01 The above equipment has been tested by Bureau Veritas Consumer Products Services (H.K.) Ltd., Taoyuan Branch, and found compliance with the requirement of the above standards. The test record, data evaluation & Equipment Under Test (EUT) configurations represented herein are true and accurate accounts of the measurements of the sample’s RF characteristics under the conditions specified in this report. Prepared by : , Date:Aug. 09, 2022 Celine Chou / Senior Specialist Approved by : , Date:Aug. 09, 2022 Jeremy Lin / Project Engineer Report No.: MFBDYS-WTW-P22031091 Page No. 5 / 11 Report Format Version: 6.1.2 2 Applicable RF Exposure Limit § 1.1310 Radiofrequency radiation exposure limits. (a) Specific absorption rate (SAR) shall be used to evaluate the environmental impact of human exposure to radiofrequency (RF) radiation as specified in § 1.1307(b) of this part within the frequency range of 100 kHz to 6 GHz (inclusive). (b) The SAR limits for occupational/controlled exposure are 0.4 W/kg, as averaged over the whole body, and a peak spatialaverage SAR of 8 W/kg, averaged over any 1 gram of tissue (defined as a tissue volume in the shape of a cube). Exceptions are the parts of the human body treated as extremities, such as hands, wrists, feet, ankles, and pinnae, where the peak spatial-average SAR limit for occupational/controlled exposure is 20 W/kg, averaged over any 10 grams of tissue (defined as a tissue volume in the shape of a cube). Exposure may be averaged over a time period not to exceed 6 minutes to determine compliance with occupational/controlled SAR limits. (c) The SAR limits for general population/uncontrolled exposure are 0.08 W/kg, as avera…

Text truncated - open the document above for the full version.

Report No.: RFBDYS-WTW-P22031091-1 Page No. 1 / 125 Report Format Version:6.1.2 FCC Test Report Report No.: RFBDYS-WTW-P22031091-1 FCC ID: 2AKCZ-108 Test Model: APL68-108 Received Date: Mar. 28, 2022 Test Date: Apr. 08 ~ May 27, 2022 Issued Date: Aug. 09, 2022 Applicant: SonicWall Inc. Address: 1033 McCarthy Blvd., Milpitas, CA 95035, USA Issued By: Bureau Veritas Consumer Products Services (H.K.) Ltd., Taoyuan Branch Lin Kou Laboratories Lab Address: No. 47-2, 14th Ling, Chia Pau Vil., Lin Kou Dist., New Taipei City, Taiwan Test Location (1): No. 19, Hwa Ya 2nd Rd., Wen Hwa Vil., Kwei Shan Dist., Taoyuan City 33383, TAIWAN FCC Registration / Designation Number: 788550 / TW0003 Test Location (2): No. 70, Wenming Rd., Guishan Dist., Taoyuan City 333, Taiwan (R.O.C.) FCC Registration / Designation Number: 281270 / TW0032 This report is governed by, and incorporates by reference, the Conditions of Testing as posted at the date of issuance of this report at http://www.bureauveritas.com/home/about-us/our-business/cps/about-us/terms-conditions/ and is intended for your exclusive use. Any copying or replication of this report to or for any other person or entity, or use of our name or trademark, is permitted only with our prior written permission. This report sets forth our findings solely with respect to the test samples identified herein. The results set forth in this report are not indicative or representative of the quality or characteristics of the lot from which a test sample was taken or any similar or identical product unless specifically and expressly noted. Our report includes all of the tests requested by you and the results thereof based upon the information that you provided to us. Measurement uncertainty is only provided upon request for accredited tests. Statements of conformity are based on simple acceptance criteria without taking measurement uncertainty into account, unless otherwise requested in writing. You have 60 days from date of issuance of this report to notify us of any material error or omission caused by our negligence or if you require measurement uncertainty; provided, however, that such notice shall be in writing and shall specifically address the issue you wish to raise. A failure to raise such issue within the prescribed time shall constitute your unqualified acceptance of the completeness of this report, the tests conducted and the correctness of the report contents. Report No.: RFBDYS-WTW-P22031091-1 Page No. 2 / 125 Report Format Version:6.1.2 Table of Contents Release Control Record .................................................................................................................................. 4 1 Certificate of Conformity ...................................................................................................................... 5 2 Summary of Test Results ..................................................................................................................... 6 2.1 Measurement Uncertainty ................................................................................................................... 6 2.2 Modification Record ............................................................................................................................ 6 3 General Information .............................................................................................................................. 7 3.1 General Description of EUT ................................................................................................................ 7 3.2 Description of Test Modes ................................................................................................................. 10 3.2.1 Test Mode Applicability and Tested Channel Detail ............................................................................ 11 3.3 Duty Cycle of Test Signal .................................................................................................................. 14 3.4 Description of Support Units ............................................................................................................. 16 3.4.1 Configuration of System under Test .................................................................................................. 16 3.5 General Description of Applied Standards and References ............................................................. 17 4 Test Types and Results ...................................................................................................................... 18 4.1 Radiated Emission and Bandedge Measurement ............................................................................. 18 4.1.1 Limits of Radiated Emission and Bandedge Measurement .............................................................. 18 4.1.2 Test Instruments ................................................................................................................................ 19 4.1.3 Test Procedures ................................................................................................................................. 20 4.1.4 Deviation from Test Standard ............................................................................................................ 21 4.1.5 Test Setup .......................................................................................................................................... 21 4.1.6 EUT Operating Conditions ................................................................................................................. 22 4.1.7 Test Results ....................................................................................................................................... 23 4.2 Conducted Emission Measurement .................................................................................................. 67 4.2.1 Limits of Conducted Emission Measurement .....................................................................…

Text truncated - open the document above for the full version.

SONICWAVE 621 Antenna Test Report Customer SonicWall Project SONICWAVE 621 Project Description 2.4G antenna *2 5G antenna *2 BLE antenna *1 Scan antenna *1 Date 2022/01/05 Prepared by Kenny Checked Tony Report Version A02 Executive Summary •Agenda –Placement and Specification –VSWR & Isolation –Radiation Pattern –Combine Pattern –Efficiency and Gain Placement and specification Ant No. Operating Band Gain (dBi) Efficiency (%) Ant type Material Feeding Dimension 2G1~2G2 2400MHz ~ 2500 MHz 3.05~3.64 61.1~69.4 PIFA Metal Cable 29*10*7 mm 3 5G1~5G2 5150MHz ~ 5850 MHz 4.13~5.07 61.5~66.6 PIFA Metal Cable 21*10*5 mm 3 BLE 2400MHz ~ 2500 MHz 3.09~3.70 61.0~68.8 PIFA Metal Cable 29*10*7 mm 3 Scan 2400MHz ~ 2500 MHz 5150MHz ~ 5850 MHz 3.81~3.93 3.81~4.89 60.3~62.2 60.0~63.9 PIFA Metal Cable 30.2*6.3*10.3 mm 3 5G2 2G1 BLE 2G2 5G1 Scan 5G1 2G2 BLE 2G1 5G2 Scan VSWR VSWR Freq. (MHz) 2G1 2G2 5G1 5G2 2400 1.67 1.59 11.60 9.58 2450 1.29 1.29 11.45 9.88 2500 1.41 1.08 10.74 9.30 5150 4.39 5.50 1.32 1.16 5500 4.27 5.34 1.37 1.26 5850 3.92 4.75 1.29 1.39 VSWR VSWR Freq. (MHz) BLE Scan 2400 1.44 1.43 2450 1.24 1.05 2500 1.15 1.27 5150 5.31 1.81 5500 4.64 1.25 5850 4.32 1.21 Isolation Isolation Freq. (MHz) 2G1-2G2 2G1-BLE 2G2-BLE 2G1-Scan 2G2-Scan 2400 -24.47 -21.95 -26.73 -22.15 -20.31 2450 -22.37 -22.62 -34.44 -20.82 -20.13 2500 -25.10 -22.72 -27.76 -20.07 -21.05 5150 -41.86 -48.79 -45.87 -39.49 -37.71 5500 -41.66 -43.11 -45.36 -35.70 -33.97 5850 -39.70 -53.13 -42.65 -32.08 -32.47 Isolation Isolation Freq. (MHz) 5G1-5G2 5G1-Scan 5G2-Scan BLE-Scan 2400 -59.15 -25.00 -26.26 -19.86 2450 -51.54 -23.87 -25.65 -21.24 2500 -42.79 -23.61 -28.40 -19.64 5150 -20.96 -23.70 -23.72 -36.06 5500 -26.35 -22.47 -22.41 -35.27 5850 -27.34 -23.06 -22.90 -36.55 2D Radiation Pattern – 2G1 @ 2.45GHz Front side Top Front side Front side I/O port I/O port I/O port Top LED LED X Z Y 2G1 2D Radiation Pattern – 2G2 @ 2.45GHz Front side Front side I/O port X Z Y I/O port Top LED 2G2 Front side Top I/O port LED 2D Radiation Pattern – 5G1 @ 5.55GHz Front side Front side I/O port X Z Y I/O port Top LED 5G1 Front side Top I/O port LED 2D Radiation Pattern – 5G2 @ 5.55GHz Front side Front side I/O port X Z Y I/O port Top LED 5G2 Front side Top I/O port LED 2D Radiation Pattern – BLE @ 2.45GHz Front side Front side I/O port X Z Y I/O port Top LED BLE Front side Top I/O port LED 2D Radiation Pattern – Scan @ 2.45GHz Front side Front side I/O port X Z Y I/O port Top LED Scan Front side Top I/O port LED Scan 2D Radiation Pattern – Scan @ 5.55GHz Front side Front side I/O port X Z Y I/O port Top LED Front side Top I/O port LED Combine pattern – 2G1+2G2 @2.45 GHz +Y +X +X +Z +Y +Z Front side Front side I/O port I/O port Top LED Front side Top I/O port LED Combine pattern – 5G1+5G2 @5.55 GHz +Y +X +X +Z +Y +Z Front side Front side I/O port I/O port Top LED Front side Top I/O port LED Antenna Efficiency and Gain Antenna Performance Freq. (MHz) 2G1 2G2 Efficiency (%) Peak Gain (dBi) Efficiency (%) Peak Gain (dBi) 2400 61.1 3.05 63.8 3.52 2450 62.4 3.14 69.4 3.43 2500 63.7 3.21 66.7 3.64 Antenna Performance Freq. (MHz) 5G1 5G2 Efficiency (%) Peak Gain (dBi) Efficiency (%) Peak Gain (dBi) 5150 64.8 4.52 64.3 4.13 5500 66.6 4.63 63.4 4.98 5850 61.5 5.07 65.2 4.62 Antenna Performance Freq. (MHz) BLE Efficiency (%) Peak Gain (dBi) 2400 61.0 3.09 2450 65.4 3.70 2500 68.8 3.58 Antenna Performance Freq. (MHz) Scan Efficiency (%) Peak Gain (dBi) 2400 60.4 3.83 2450 62.2 3.93 2500 60.3 3.81 5150 60.5 3.81 5500 60.0 4.23 5850 63.9 4.89

Reference No.: BDYS-WTW-P22031091_TSup Page No. 1 / 5 PHOTOGRAPHS OF THE TEST CONFIGURATION Conducted Emission Test Test Mode A Reference No.: BDYS-WTW-P22031091_TSup Page No. 2 / 5 Conducted Emission Test Test Mode B Reference No.: BDYS-WTW-P22031091_TSup Page No. 3 / 5 Radiated Emission Test (Above 1GHz) Reference No.: BDYS-WTW-P22031091_TSup Page No. 4 / 5 Radiated Emission Test (Below 1GHz) Test Mode A Reference No.: BDYS-WTW-P22031091_TSup Page No. 5 / 5 Radiated Emission Test (Below 1GHz) Test Mode B