2ALC5-KNX-ATI1Tag

▪ ▪ ▪ ▪ ▪ ▪ ▪ ▪ ▪ ▪ ▪ ▪ Please mind that tag LED behaviour depends on the firmware use case one has selected. Most important ver- sions are: Regulatory and Legal Information The Kinexon Asset Tag has been designed to be in compliance with both the U.S. FCC Part 15 subpart F regulations, sections 15.517 and 15.521 and with the European Union ETSI EN 302 065 standards. Two different versions of the Kinexon Asset Tag are available, one version supports the FCC emissions mask (Region 1) and the second supports the ETSI standard mask (Region 2). Disclaimer The information in this document is subject to change without notice. Kinexon GmbH assumes no responsibility for inaccuracies or omissions and specifically disclaims any liabilities, losses, or risks, personal or otherwise, incurred as a consequence, directly or indirectly, of the use or application of any of the contents of this document. For the latest documentation, contact Kinexon GmbH. Intended Use This manual describes the setup and use of the Kinexon Asset Tag. Use this product only for the purpose it was designed for. FCC Compliance This device complies with 47 CFR Part 15 of the FCC Rules. Operation is subject to the following two conditions: (1) This device may not cause harmful interference, and (2) this device must accept any interference received, including interference that may cause undesired operation. The user is cautioned that changes or modifications not expressly approved by the party responsible for compliance could void the user’s authority to operate the equipment. This device may not be employed for the operation of toys. Operation onboard an aircraft, a ship or a satellite is prohibited. This equipment may only be operated indoors. Operation outdoors is in violation of 47 U.S.C. 301 and could subject the operator to serious legal penalties. The use of this device mounted on outdoor structures, e.g., on the outside of a building or on a telephone pole, or any fixed outdoors infrastructure is prohibited. This device communicates with an associated anchor which needs to be mounted indoors. To ensure indoor communication only, the tag will stop transmitting once it loses connection to the KINEXON Anchors mounted indoors and start transmitting only when a connection is re-established by the anchors. Moreover, the following statements apply: Note: This equipment has been tested and found to comply with the limits for a Class B digital device, pursuant to part 15 of the FCC Rules. These limits are designed to provide reasonable protection against harmful interference in a residential installation. This equipment generates, uses, and can radiate radio frequency energy and, if not installed and used in accordance with the instructions, may cause harmful interference to radio communications. However, there is no guarantee that interference will not occur in a particular installation. If this equipment does cause harmful interference to radio or television reception, which can be determined by turning the equipment off and on, the user is encouraged to try to correct the interference by one or more of the following measures: • Reorient or relocate the receiving antenna. • Increase the separation between the equipment and receiver. • Connect the equipment to an outlet on a circuit different from that to which the receiver is connected. • Consult the dealer or an experienced radio/TV technician for help. FCC Caution Changes or modifications not expressly approved by the party responsible for compliance could void the user’s authority to operate the equipment. This device is designed not to exceed the limits for exposure to radio waves adopted by the FCC. These limits include a substantial safety margin design to assure the safety of all persons, regardless of age and health. The radio wave exposure guidelines use a unit of measurement known as the Specific Absorption Rate (SAR). SAR levels have been computed for the transmitters in this device and have been found to be below FCC limits. Safety Information • Read and follow all instructions before using the Kinexon Asset Tag. • Never open the case of the Kinexon Asset Tag. There are no user serviceable parts or replaceable parts inside the case. • Do not use the Kinexon Asset Tag if it has been damaged.

KINEXON Inc. 25 Broadway, Floor 9 NYC, NY 10004 United States Tel: +1 347 630 0208 www.kinexon.com KINEXON Inc. 25 Broadway, Floor 9 NYC, NY 10004, USA +1 347 630 0208 PHOENIX TESTLAB GmbH Product Certification Department Königswinkel 10 D 32825 Blomberg To Whom It May Concern, Please be advised that we (KINEXON Inc., 25 Broadway, Floor 9, New York, NY 10004) authorize the following employees from EMV Testhaus GmbH: • Mr. Tobias Zollner • Mr. Christian Kiermeier • Mr. Konrad Graßl to handle the application of Type Approval Services for the following countries: USA. Unless future correspondence from us, please extend your full cooperation to EMV Testhaus GmbH regarding matters to the above mentioned products to 24 months after the signatory date of this authorization. Mehdi Bentanfous CEO 08/22/19 ___________________________ Signatory KINEXON Inc. 25 Broadway, Floor 9 NYC, NY 10004 United States Tel: +1 347 630 0208 www.kinexon.com

Long/Short-term Confidentiality Request PHOENIX TESTLAB GmbH Date: 22 June 2020 Product Certification Königswinkel 10 D 32825 Blomberg FCC ID: 2ALC5-KNX-ATI1 To Whom It May Concerns, Pursuant to sections 0.457(d) and 0.459 of CFR 47 and to avoid premature release of sensitive information prior to marketing or release of the product to the public, we hereby request long-term confidential treatment of information accompanying this application as outlined below: ☒ Schematics ☐ Parts List ☒ Block Diagram ☐ Tune-Up Info ☐ Operational Description In addition we hereby request the following exhibits contained in this application to be temporarily (short-term confidentiality) withheld from the public disclosure ☐ for an initial period of days ☐ until: ☒ not applicable ☐ External Photos ☐ Test Setup Photos ☐ Internal Photos ☐ Users Manual The above materials contain trade secrets and proprietary information not customarily released to the public. The public disclosure of these matters might be harmful to the applicant and provide unjustified benefits to its competitors. The applicant understands that pursuant to rule 0.457(d), disclosure of this application and all accompanying documentation will not be made before the date of the GRANT for this application. If you have any questions, please feel free to contact me. Yours sincerely, Christian Kiermeier Laboratory Manager

EMV TESTHAUS GmbH Gustav-Hertz-Straße 35 94315 Straubing Germany Revision: 1.7 KINEXON Inc. Tag KNX-T4.1-1.2-2:B 190123-AU01+W01 Annex B Page 1 of 3 1 Annex B – EUT pictures 1.1 List of Pictures Picture 1: EUT top side ...................................................................................................... 2 Picture 2: EUT bottom side ................................................................................................ 2 Picture 3: EUT label ........................................................................................................... 3 EMV TESTHAUS GmbH Gustav-Hertz-Straße 35 94315 Straubing Germany Revision: 1.7 KINEXON Inc. Tag KNX-T4.1-1.2-2:B 190123-AU01+W01 Annex B Page 2 of 3 Picture 1: EUT top side Picture 2: EUT bottom side EMV TESTHAUS GmbH Gustav-Hertz-Straße 35 94315 Straubing Germany Revision: 1.7 KINEXON Inc. Tag KNX-T4.1-1.2-2:B 190123-AU01+W01 Annex B Page 3 of 3 Picture 3: EUT label

Label: Location:

EMV TESTHAUS GmbH Gustav-Hertz-Straße 35 94315 Straubing Germany Revision: 1.7 KINEXON Inc. Tag KNX-T4.1-1.2-2:B 190123-AU01+W01 Annex C Page 1 of 5 1 Annex C – documentation 1.1 List of Pictures Picture 1: Internal view top side ......................................................................................... 2 Picture 2: Internal view cover ............................................................................................. 2 Picture 3: Top view of PCB with RF part............................................................................ 3 Picture 4: Bottom view of PCB ........................................................................................... 3 Picture 5: UWB chip .......................................................................................................... 4 Picture 6: UWB antenna .................................................................................................... 4 Picture 7: Battery bottom view ........................................................................................... 5 Picture 8: Battery bottom view ........................................................................................... 5 EMV TESTHAUS GmbH Gustav-Hertz-Straße 35 94315 Straubing Germany Revision: 1.7 KINEXON Inc. Tag KNX-T4.1-1.2-2:B 190123-AU01+W01 Annex C Page 2 of 5 Picture 1: Internal view top side Picture 2: Internal view cover EMV TESTHAUS GmbH Gustav-Hertz-Straße 35 94315 Straubing Germany Revision: 1.7 KINEXON Inc. Tag KNX-T4.1-1.2-2:B 190123-AU01+W01 Annex C Page 3 of 5 Picture 3: Top view of PCB with RF part Picture 4: Bottom view of PCB EMV TESTHAUS GmbH Gustav-Hertz-Straße 35 94315 Straubing Germany Revision: 1.7 KINEXON Inc. Tag KNX-T4.1-1.2-2:B 190123-AU01+W01 Annex C Page 4 of 5 Picture 5: UWB chip Picture 6: UWB antenna EMV TESTHAUS GmbH Gustav-Hertz-Straße 35 94315 Straubing Germany Revision: 1.7 KINEXON Inc. Tag KNX-T4.1-1.2-2:B 190123-AU01+W01 Annex C Page 5 of 5 Picture 7: Battery bottom view Picture 8: Battery bottom view

Fact Sheet KINEXON LOCALIZATION SYSTEM Operational Description – Asset Tag Indoor Version 1.1 ©Kinexon 2019. This document contains information which is proprietary to Kinexon GmbH. No reproduction is permitted without prior express written permission of the author ([email protected]). 2 Kinexon System The Kinexon System is a Real-Time Location System (RTLS) based on Ultra-Wideband (UWB) technology. Its primary use is for the tracking of people or objects. The system operates using active Tags, a network of Anchors, and a Kinexon Sensor Network Application. Anchors: The Kinexon Anchors are devices that are mounted in the area of coverage. The Anchors serve as reference points for the localization and communicate with associated Asset Tags. Kinexon Sensor Network Application: The Kinexon Sensor Network Application (SNA) coordinates multiple Anchors within the Kinexon Network. The SNA is also collecting the data via Wifi or Ethernet from the Anchors and passes this data to other application (e.g., Kinexon Server Application). Tag: The Tag is a small, transceiving device with an integrated antenna. It senses different data (e.g., accelerations, temperature) and transmits the data to the KINEXON Anchors. The duty cycle can be set in the KINEXON Server Application or triggered by movement with an onboard accelerometer. The KINEXON Asset Tag Indoor is powered via a small included battery, which can - depending on system settings - guarantee operation for up to several years. The data is modulated using a variable pulse position modulation combined with binary phase shift keying. An integrated chip antenna emits the RF signals. The KINEXON Asset Tag Indoor will communicate on UWB Channel 3 (Center Frequency 4.5 GHz) with a bandwidth of 500 MHz (4.25 GHz to 4.75 GHz). To ensure indoor communication only, the tag will stop transmitting once it loses connection to the KINEXON Anchors mounted indoors and start transmitting only when a connection is re-established by the anchors. Anchor Tag

The test result refers exclusively to the model tested. This test report may not be copied or published in extracts without the written authorization of the accreditation agency and/or EMV TESTHAUS GmbH RF test report 190123-AU01+W01 KINEXON Inc. Tag KNX-T4.1-1.2-2:B Customer: KINEXON Inc. 25 Broadway, Floor 9 New York, NY 10004 EMV TESTHAUS GmbH Gustav-Hertz-Straße 35 94315 Straubing Germany KINEXON Inc. Tag KNX-T4.1-1.2-2:B 190123-AU01+W01 Page 2 of 64 EMV TESTHAUS GmbH Gustav-Hertz-Straße 35 94315 Straubing Tel.: +49 9421 56868-0 Fax: +49 9421 56868-100 Email: [email protected] Accreditation: FCC test firm accreditation expiration date: 2021-05-30 MRA US-EU, FCC designation number: DE0010 FCC registration number: 97268 BnetzA-CAB-02/21-02/5 Valid until 2023-11-26Location of Testing: EMV TESTHAUS GmbH Gustav-Hertz-Straße 35 94315 Straubing The technical accuracy is guaranteed through the quality management of the EMV TESTHAUS GmbH. EMV TESTHAUS GmbH Gustav-Hertz-Straße 35 94315 Straubing Germany KINEXON Inc. Tag KNX-T4.1-1.2-2:B 190123-AU01+W01 Page 3 of 64 Table of contents 1 Summary of test results ............................................................................................................ 5 2 Referenced publications ........................................................................................................... 7 3 Equipment under test (EUT) ..................................................................................................... 8 3.1 General remark .................................................................................................................. 8 3.2 General information ........................................................................................................... 8 3.3 Radio specifications ........................................................................................................... 9 3.4 Photo documentation ......................................................................................................... 9 4 Test configuration and mode of operation ............................................................................... 10 4.1 Test configuration ............................................................................................................ 10 4.2 Mode of operation ............................................................................................................ 11 5 Test procedures...................................................................................................................... 11 5.1 General specifications ..................................................................................................... 11 5.2 AC power-line conducted emissions ................................................................................ 12 5.3 Radiated emissions below 30 MHz .................................................................................. 14 5.4 Radiated emissions from 30 MHz to 1 GHz ..................................................................... 16 5.5 Radiated emissions above 1 GHz .................................................................................... 18 5.6 UWB Bandwidth measurement ........................................................................................ 19 6 Test results ............................................................................................................................. 20 6.1 Antenna requirement ....................................................................................................... 21 6.2 Signal deactivation........................................................................................................... 22 6.3 UWB bandwidth ............................................................................................................... 26 6.4 Radiated emissions in GPS bands ................................................................................... 31 6.5 Peak emissions in a 50 MHz bandwidth ........................................................................... 39 6.6 Radiated emissions 9 kHz to 40 GHz............................................................................... 44 7 Equipment calibration status ................................................................................................... 62 8 Measurement uncertainties .................................................................................................... 63 9 Revision history ...................................................................................................................... 64 EMV TESTHAUS GmbH Gustav-Hertz-Straße 35 94315 Straubing Germany KINEXON Inc. Tag KNX-T4.1-1.2-2:B 190123-AU01+W01 Page 4 of 64 List of figures Figure 1: Setup for AC power-line conducted emissions test from 150 kHz to 30 MHz .................. 13 Figure 2: Setup for radiated emissions test below 30 MHz ............................................................ 16 Figure 3: Setup for radiated emissions test from 30 MHz to 1 GHz ............................................... 18 Figure 4: Chart of signal deactivation test on channel 3 – power supply of anchor disconnected .. 24 Figure 5: Chart of signal deactivation test on channel 3 – LAN disconnected ................................ 25 Figure 6: Chart of UWB bandwidth on channel 2 ........................................................................... 28 Figure 7: Chart of UWB bandwidth on channel 3 ........................................................................... 29 Figure 8: Chart of UWB bandwidth on channel 5 ........................................................................... 30 Figure 9: Chart of measurement 1164 MHz to 1240 MHz on channel 2 ......................................... 33 Figure 10: Chart of measurement 1559 MHz to 1610 MHz on channel 2 ....................................... 34 Figure 11: Chart of measurement 1164 MHz to 1240 MHz on channel 3 ................…

Text truncated - open the document above for the full version.

EMV TESTHAUS GmbH Gustav-Hertz-Straße 35 94315 Straubing Germany Revision: 1.7 KINEXON Inc. Tag KNX-T4.1-1.2-2:B 190123-AU01+W01 Annex A Page 1 of 10 1 Annex A – Test setup 1.1 List of Pictures Picture 1: EUT position 0 º ................................................................................................. 2 Picture 2: EUT position 30 º ............................................................................................... 2 Picture 3: EUT position 60 º ............................................................................................... 3 Picture 4: EUT position 90 º ............................................................................................... 3 Picture 5: EUT position 120 º ............................................................................................. 4 Picture 6: EUT position 150 º ............................................................................................. 4 Picture 7: EUT test setup UWB bandwidth measurement ................................................. 5 Picture 8: EUT test setup radiated emissions in GPS bands measurement ...................... 5 Picture 9: EUT test setup Peak emissions in a 50 MHz bandwidth measurement ............. 6 Picture 10: EUT test setup Peak emissions in a 50 MHz bandwidth relative measurement ..................................................................................................................... 6 Picture 11: EUT test setup radiated emissions test from 9 kHz to 30 MHz ........................ 7 Picture 12: EUT test setup radiated emissions test from 30 MHz to 960 MHz................... 7 Picture 13: EUT test setup radiated emissions test from 960 MHz to 17 GHz ................... 8 Picture 14: EUT test setup radiated emissions test from 17 GHz to 40 GHz ..................... 8 Picture 15: EUT test setup radiated emissions test from 30 MHz to 960 MHz................... 9 Picture 16: EUT test setup radiated emissions test from 960 MHz to 17 GHz ................... 9 Picture 17: EUT test setup radiated emissions test from 17 GHz to 40 GHz ..................... 10 Picture 18: Signal deactivation test .................................................................................... 10 EMV TESTHAUS GmbH Gustav-Hertz-Straße 35 94315 Straubing Germany Revision: 1.7 KINEXON Inc. Tag KNX-T4.1-1.2-2:B 190123-AU01+W01 Annex A Page 2 of 10 Picture 1: EUT position 0 º Picture 2: EUT position 30 º EMV TESTHAUS GmbH Gustav-Hertz-Straße 35 94315 Straubing Germany Revision: 1.7 KINEXON Inc. Tag KNX-T4.1-1.2-2:B 190123-AU01+W01 Annex A Page 3 of 10 Picture 3: EUT position 60 º Picture 4: EUT position 90 º EMV TESTHAUS GmbH Gustav-Hertz-Straße 35 94315 Straubing Germany Revision: 1.7 KINEXON Inc. Tag KNX-T4.1-1.2-2:B 190123-AU01+W01 Annex A Page 4 of 10 Picture 5: EUT position 120 º Picture 6: EUT position 150 º EMV TESTHAUS GmbH Gustav-Hertz-Straße 35 94315 Straubing Germany Revision: 1.7 KINEXON Inc. Tag KNX-T4.1-1.2-2:B 190123-AU01+W01 Annex A Page 5 of 10 Picture 7: EUT test setup UWB bandwidth measurement Picture 8: EUT test setup radiated emissions in GPS bands measurement EMV TESTHAUS GmbH Gustav-Hertz-Straße 35 94315 Straubing Germany Revision: 1.7 KINEXON Inc. Tag KNX-T4.1-1.2-2:B 190123-AU01+W01 Annex A Page 6 of 10 Picture 9: EUT test setup Peak emissions in a 50 MHz bandwidth measurement Picture 10: EUT test setup Peak emissions in a 50 MHz bandwidth relative measurement EMV TESTHAUS GmbH Gustav-Hertz-Straße 35 94315 Straubing Germany Revision: 1.7 KINEXON Inc. Tag KNX-T4.1-1.2-2:B 190123-AU01+W01 Annex A Page 7 of 10 Picture 11: EUT test setup radiated emissions test from 9 kHz to 30 MHz Picture 12: EUT test setup radiated emissions test from 30 MHz to 960 MHz EMV TESTHAUS GmbH Gustav-Hertz-Straße 35 94315 Straubing Germany Revision: 1.7 KINEXON Inc. Tag KNX-T4.1-1.2-2:B 190123-AU01+W01 Annex A Page 8 of 10 Picture 13: EUT test setup radiated emissions test from 960 MHz to 17 GHz Picture 14: EUT test setup radiated emissions test from 17 GHz to 40 GHz EMV TESTHAUS GmbH Gustav-Hertz-Straße 35 94315 Straubing Germany Revision: 1.7 KINEXON Inc. Tag KNX-T4.1-1.2-2:B 190123-AU01+W01 Annex A Page 9 of 10 Picture 15: EUT test setup radiated emissions test from 30 MHz to 960 MHz Picture 16: EUT test setup radiated emissions test from 960 MHz to 17 GHz EMV TESTHAUS GmbH Gustav-Hertz-Straße 35 94315 Straubing Germany Revision: 1.7 KINEXON Inc. Tag KNX-T4.1-1.2-2:B 190123-AU01+W01 Annex A Page 10 of 10 Picture 17: EUT test setup radiated emissions test from 17 GHz to 40 GHz Picture 18: Signal deactivation test