2AMG5-STG68843 in 1 Magnetic Wireless Charging Station

3 in 1 Magnetic Wireless Charger station USER MANUAL Model No.:TC046Input:DC 9V/2A,9V/3A Output for iPhone:Max.15WOutput for iWatch:Max.3W Output for Airpods:Max.5WCharging Standard:qi Charging Ffficiency:75%~85%Charging Distance:3~8mm Support Devices: iPhone 12/13 series, iWatch series,Airpods series Content:Charger Staon x1,Type-C Charging Cable x 1,User Manual x 1 Specification 1.Do not squeeze or collied. 2.Do not disassemble or throw into fire or wate,to avoid causing a short circuit leakage. 3.Do not use wireless charger in severely hot,humid or corrosive enviroments to avoid circuit damage and occure leakage phenomenon. 4.Do not use it while the FOD had triggered. 5.Do not place too close with magnec stripe or chip card(ID card,bank cards,etc.) to avoid magenc failure. This is a 3in1 wireless charging stand built in intelligent and advance chipset. Support charge your mobile phone, smart watch and airpods at the same time. It will bring you excellent and convenient fast wireless charging. Product Description iWatch charger Stand iPhone 12/13 charging area Airpods charging area Indic ator Installation steps Safety Instruction 1. Use a min.9V/3A adpter as power suppliy, the red indicator will on. 2. Put your devices on the induction area, blue indicator means it is on charging 3. The indicator will off while your devices had been full charged. 4.If the indicator is flicking,that means the FOD had triggered. Size FCC Warning 15.19 Labeling requirements. This device complies with part 15 of the FCC Rules. Operation is subject to the following two conditions: (1) This device may not cause harmful interference, and (2) this device must accept any interference received, including interference that may cause undesired operation. 15.21 Information to user. Any Changes or modifications not expressly approved by the party responsible for compliance could void the user's authority to operate the equipment. 15.105 Information to the user. Note: This equipment has been tested and found to comply with the limits for a Class B digital device, pursuant to part 15 of the FCC Rules. These limits are designed to provide reasonable protection against harmful interference in a residential installation. This equipment generates uses and can radiate radio frequency energy and, if not installed and used in accordance with the instructions, may cause harmful interference to radio communications. However, there is no guarantee that interference will not occur in a particular installation. If this equipment does cause harmful interference to radio or television reception, which can be determined by turning the equipment off and on, the user is encouraged to try to correct the interference by one or more of the following measures: -Reorient or relocate the receiving antenna. -Increase the separation between the equipment and receiver. -Connect the equipment into an outlet on a circuit different from that to which the receiver is connected. -Consult the dealer or an experienced radio/TV technician for help. FCC RF Radiation Exposure Statement: 1.This Transmitter must not be co-located or operating in conjunction with any other antenna or transmitter. 2.This equipment complies with RF radiation exposure limits set forth for an uncontrolled environment. This equipment should be installed and operated with minimum distance 15cm between the radiator and your body. IC Warning This device complies with Industry Canada’s licence-exempt RSSs. Operation is subject to the following two conditions: (1)This device may not cause interference; (2)This device must accept any interference, including interference that may cause undesired operation of the device. Le présent appareil est conforme aux CNR d'Industrie Canada applicables aux appareils radio exempts de licence. L'exploitation est autorisée aux deux conditions suivantes: (1)l'appareil ne doit pas produire de brouillage, et (2)l'utilisateur de l'appareil doit accepter tout brouillage radioélectrique subi, même si le brouillage est susceptible d'en compromettre le fonctionnement. The information listed above provides the user with information needed to make him or her aware of a RF exposure, and what to do to assure that this radio operates within the FCC exposure limits of this radio. The device complies with RF specifications when the device used at 10cm from the body. Third-party belt-clips, holsters, and similar accessories used by this device should not contain any metallic components. Body-worn accessories that do not meet these requirements may not comply with RF exposure requirements and should be avoided. Use only the supplied or an approved antenna.

JLR Gear 2.911 (d)(5)(i) Equipment Type Attestation v1.2 Section 2.911(d)(5)(i) Certification – Equipment Type C ompany name: JLR Gear Address: 2434 Research Dr Livermore,CA 94550,United States Product Name: 3 in 1 Magnetic Wireless Charging Station FCC ID: 2AMG5-STG6884 Model(s): STG-6884-KB, STG-6898-TX, TC046 2.91 1(d)(5)(i) Equipment Type We, [JLR Gear ] (“the applicant”) certify that the equipment for which authorization is sought through certification is not: •Prohibited from receiving an equipment authorization pursuant to § 2.903; of the FCC rules. •Identified as an equipment type in the “Covered List” NOTE 1 Y ours sincerely, Name: Eric Marshburn Date: 2023-03-22 T itle and Company name: Manager NOTE 1 “Covered List ”; is the List of Equipment and Services Covered By Section 2 of The Secure Networks Act, available at https://www.fcc.gov/supplychain/coveredlist References; 1)986446 D01 Covered Equipment v01 https://apps.fcc.gov/oetcf/kdb/forms/FTSSearchResultPage.cfm?switch=P&id=325672 2) F ederal Register document 2022-28263 published on 02/06/23 https://www.federalregister.gov/documents/2023/02/06/2022-28263/protecting-against-national-security-threats-to-the-com munications-supply-chain-through-the

JLR Gear 2.911 (d)(5)(ii) Applicant Attestation v1.2 Section 2.911(d)(5)(ii) Certification – Applicant (Covered List ) C ompany name: JLR Gear Address: 2434 Research Dr Livermore,CA 94550,United States Product Name: 3 in 1 Magnetic Wireless Charging Station FCC ID: 2AMG5-STG6884 Model(s): STG-6884-KB, STG-6898-TX, TC046 2.91 1(d)(5)(ii) Applicant filing We, [JLR Gear ] (“the applicant”) certify that, as of the date of the filing of the application, the applicant is not identified NOTE 1 on the “Covered List” NOTE 2 , established pursuant to § 1.50002 of this chapter, as an entity producing covered communications equipment. Y ours sincerely, Name: Eric Marshburn Date: 2023-03-22 T itle and Company name: Manager NOTE 1 Delete option not applicable to this application. NOTE 2 “Covered List ”; is the List of Equipment and Services Covered By Section 2 of The Secure Networks Act, available at https://www.fcc.gov/supplychain/coveredlist References; 1)986446 D01 Covered Equipment v01 https://apps.fcc.gov/oetcf/kdb/forms/FTSSearchResultPage.cfm?switch=P&id=325672 2) F ederal Register document 2022-28263 published on 02/06/23 https://www.federalregister.gov/documents/2023/02/06/2022-28263/protecting-against-national-security-threats-to-the-com munications-supply-chain-through-the

JLR Gear 2. 911 (d)(7)USA Agent v1.2 Section 2.911(d)(7) USA Agent for Service of Process Company name: JLR Gear Address: 2434 Research Dr Livermore,CA 94550,United States Product Name: 3 in 1 Magnetic Wireless Charging Station FCC ID: 2AMG5-STG6884 Model(s): STG-6884-KB, STG-6898-TX, TC046 2.91 1(d)(7) USA Designated Agent for Service of Process W e, [JLR Gear] (“the applicant”) designate [JLR Gear] NOTE1 for the purpose of accepting service of process on behalf of the applicant. Applicant consent: We Acknowledge our consent to accept service of process in the United States for matters related to the applicable equipment, and at the physical U.S. address and email address of the designated agent and acknowledge our acceptance of our obligation to maintain an agent for service of process in the United States for no less than one year after either the grantee has permanently terminated all marketing and importation of the applicable equipment within the U.S., or the conclusion of any Commission-related administrative or judicial proceeding involving the equipment, whichever is later. A gent obligation: We Acknowledge our obligation to accept service of process in the United States for matters related to the applicable equipment at our physical U.S. address and email address for no less than one year after either the grantee has permanently terminated all marketing and importation of the applicable equipment within the U.S., or the conclusion of any Commission-related administrative or judicial proceeding involving the equipment, whichever is later. USA Agent Company name: JLR Gear Address: 2434 Research Dr Livermore,CA 94550,United States F RN: 0026573915 FCC Grantee Code: 2AMG5 Contact Name: Eric Marshburn Telephone No: (510) 777-9894 228 Email: [email protected] Applicant Company name: JLR Gear A ddress: 2434 Research Dr Livermore,CA 94550,United States F RN: 0026573915 FCC Grantee Code: 2AMG5 Contact Name: Eric Marshburn Telephone No: (510) 777-9894 228 Email: [email protected] S ignature: Title: Manager S ignature: Title: Manager Date: 2023-03-22 Date: 2023-03-22 JLR Gear 2.911 (d)(7)USA Agent v1.2 NOTE 1: An applicant located in the United States may designate itself as the agent for service of process. Reference; Federal Register document 2022-28263 published on 02/06/23 https://www.federalregister.gov/documents/2023/02/06/2022-28263/protecting-against-national-security-threats-t o-the-communications-supply-chain-through-the

Differences Declaration T o whom concern, W e company JLR Gear H ere by declares: The product model(s) STG-6898-TX, TC046 is the same PCB layout, electronic schematic and Antenna with STG-6884-KB, the only differences between them are model names, others are same. S incerely yours, Name (in print): Eric Marshburn Company name: JLR Gear Company address: 2434 Research Dr Livermore,CA 94550,United States

Letter of Authorization Company: JLR Gear A ddress: 2434 Research Dr Livermore,CA 94550,United States Product Name: 3 in 1 Magnetic Wireless Charging Station M odel Number: STG-6884-KB, STG-6898-TX, TC046 F CC Identifier: 2AMG5-STG6884 W e authorize MiCOM Labs Inc, 575 Boulder Court, Pleasanton, California 94566, USA, to act on our behalf on all matters concerning the above named equipment. Any individual within MiCOM Labs is authorized to act on our behalf and take action on the application. W e declare that MiCOM Labs Inc, 575 Boulder Court, Pleasanton, California 94566, USA, is allowed to forward all information related to the approval project to the Federal Communication Commission and to discuss any issues concerning the approval application. Any and all acts carried out by MiCOM Labs on our behalf shall have the same effect as acts of our own. Na me: Eric Marshburn Date: 2023-03-22 Title: Manager

Test Report Number: BTF-SZ230306R-001 External Test Report Number: BTF-SZ230306R-001 Test Report Number: BTF-SZ230306R-001 Test Report Number: BTF-SZ230306R-001

Label&Location 3 in 1 Magnetic Wireless Charging Station Model: STG-6884-KB FCC ID: 2AMG5-STG6884 IC: 23078-STG6898

Test Report Number: BTF-SZ230306R-001 Internal Test Report Number: BTF-SZ230306R-001 Test Report Number: BTF-SZ230306R-001 Test Report Number: BTF-SZ230306R-001

文档编号品 名 产品尺寸 A 20.5±0.5 B 39.0±1.0 E F 1.2±0.1 G 0.8±0.1 H 测试频率测试方 式 线 材 匝 数 磁片尺寸L 线圈尺寸100KHZ 串联测试 客 户 意 见 制表张燕审核 罗勇军确认 罗勇军 日期 单位：MM 0.07*100股 绕线方式单线叠绕式 备 注 10 Ts Φ 50*Φ 5*0.8 6.5±10% 规格书 无线充发射线圈模组 粘结方式丙酮自粘 C 50.0±0.5 20230112 D 120 ±2 40AX 线圈为逆时针 方向 2.5±0.1 Φ 50*Φ5*H2.5 Φ 39.0*20.5

Total or partial reproduction of this document without permission of the Laboratory is not allowed. Page 1 of 36 BTF Testing Lab (Shenzhen) Co., Ltd. F101, 201 and 301, Building 1, Block 2, Tantou Industrial Park, Tantou Community, Songgang Street, Bao'an District, Shenzhen, China RF Test Report For Applicant Name: JLR Gear Address: 2434 Research Dr Livermore,CA 94550,United States EUT Name: 3 in 1 Magnetic Wireless Charging Station Brand Name: N/A Model Number: STG-6884-KB Series Model Number: Refer to section 2 Issued By Company Name: BTF Testing Lab (Shenzhen) Co., Ltd. Address: F101, 201 and 301, Building 1, Block 2, Tantou Industrial Park, Tantou Community, Songgang Street, Bao'an District, Shenzhen, China Report Number: BTF-SZ230306R-001 Test Standards: 47 CFR Part 15 Subpart C FCC ID: 2AMG5-STG6884 Test Conclusion: Pass Test Date: 2023-03-18 to 2023-03-20 Date of Issue: 2023-03-20 Prepared By: Chris Liu / Project Engineer Date: 2023-03-20 Approved By: Ryan.CJ / EMC Manager Date: 2023-03-20 Note: All the test results in this report only related to the testing samples. Which can be duplicated completely for the legal use with approval of applicant; it shall not be reproduced except in full without the written approval of BTF Testing Lab (Shenzhen) Co., Ltd., All the objections should be raised within thirty days from the date of issue. To validate the report, you can contact us. Test Report Number: BTF-SZ230306R-001 Total or partial reproduction of this document without permission of the Laboratory is not allowed. Page 2 of 36 BTF Testing Lab (Shenzhen) Co., Ltd. F101, 201 and 301, Building 1, Block 2, Tantou Industrial Park, Tantou Community, Songgang Street, Bao'an District, Shenzhen, China Revision History Version Issue Date Revisions Content R_V0 2023-03-20 Original Note: Once the revision has been made, then previous versions reports are invalid. Test Report Number: BTF-SZ230306R-001 Total or partial reproduction of this document without permission of the Laboratory is not allowed. Page 3 of 36 BTF Testing Lab (Shenzhen) Co., Ltd. F101, 201 and 301, Building 1, Block 2, Tantou Industrial Park, Tantou Community, Songgang Street, Bao'an District, Shenzhen, China Table of Contents 1. Introduction............................................................................................................................................................................................ 4 1.1 Identification of Testing Laboratory ................................................................................................................................. 4 1.2 Identification of the Responsible Testing Location ...................................................................................................... 4 1.3 Laboratory Condition ........................................................................................................................................................... 4 1.4 Announcement ....................................................................................................................................................................... 4 2. Product Information .............................................................................................................................................................................. 5 2.1 Application Information ....................................................................................................................................................... 5 2.2 Manufacturer Information .................................................................................................................................................... 5 2.3 Factory Information .............................................................................................................................................................. 5 2.4 General Description of Equipment under Test (EUT)................................................................................................... 5 2.5 Technical Information........................................................................................................................................................... 6 3. Summary of Test Results .................................................................................................................................................................... 7 3.1 Test Standards ....................................................................................................................................................................... 7 3.2 Summary of Test Result ...................................................................................................................................................... 7 3.3 Uncertainty of Test ................................................................................................................................................................ 7 4. Test Configuration ................................................................................................................................................................................ 8 4.1 Environment Condition ........................................................................................................................................................ 8 4.2 Test Equipment List .............................................................................................................................................................. 8 4.3 Test Auxiliary Equipment .................................................................................................................................................... 9 4.4 Test Setup ............................................................................................................................................................................. 10 5. Test Items ............................................................................…

Text truncated - open the document above for the full version.

Total or partial reproduction of this document without permission of the Laboratory is not allowed. Page 1 of 9 BTF Testing Lab (Shenzhen) Co., Ltd. F101, 201 and 301, Building 1, Block 2, Tantou Industrial Park, Tantou Community, Songgang Street, Bao'an District, Shenzhen, China RF Exposure Report For Applicant Name: JLR Gear Address: 2434 Research Dr Livermore,CA 94550,United States EUT Name: 3 in 1 Magnetic Wireless Charging Station Brand Name: N/A Model Number: STG-6884-KB Series Model Number: Refer to section 2 Issued By Company Name: BTF Testing Lab (Shenzhen) Co., Ltd. Address: F101, 201 and 301, Building 1, Block 2, Tantou Industrial Park, Tantou Community, Songgang Street, Bao'an District, Shenzhen, China Report Number: BTF-SZ230306R-002 Test Standards: 47 CFR Part 1 Subpart I Section 1.1310 FCC ID: 2AMG5-STG6884 Test Conclusion: Pass Test Date: 2023-03-18 to 2023-03-20 Date of Issue: 2023-03-20 Prepared By: Chris Liu / Project Engineer Date: 2023-03-20 Approved By: Ryan.CJ / EMC Manager Date: 2023-03-20 Note: All the test results in this report only related to the testing samples. Which can be duplicated completely for the legal use with approval of applicant; it shall not be reproduced except in full without the written approval of BTF Testing Lab (Shenzhen) Co., Ltd., All the objections should be raised within thirty days from the date of issue. To validate the report, you can contact us. Test Report Number: BTF-SZ230306R-002 Total or partial reproduction of this document without permission of the Laboratory is not allowed. Page 2 of 9 BTF Testing Lab (Shenzhen) Co., Ltd. F101, 201 and 301, Building 1, Block 2, Tantou Industrial Park, Tantou Community, Songgang Street, Bao'an District, Shenzhen, China Revision History Version Issue Date Revisions Content R_V0 2023-03-20 Original Note: Once the revision has been made, then previous versions reports are invalid. Test Report Number: BTF-SZ230306R-002 Total or partial reproduction of this document without permission of the Laboratory is not allowed. Page 3 of 9 BTF Testing Lab (Shenzhen) Co., Ltd. F101, 201 and 301, Building 1, Block 2, Tantou Industrial Park, Tantou Community, Songgang Street, Bao'an District, Shenzhen, China Table of Contents 1. Introduction............................................................................................................................................................................................ 4 1.1 Identification of Testing Laboratory ................................................................................................................................. 4 1.2 Identification of the Responsible Testing Location ...................................................................................................... 4 1.3 Laboratory Condition ........................................................................................................................................................... 4 1.4 Announcement ....................................................................................................................................................................... 4 2. Product Information .............................................................................................................................................................................. 5 2.1 Application Information ....................................................................................................................................................... 5 2.2 Manufacturer Information .................................................................................................................................................... 5 2.3 Factory Information .............................................................................................................................................................. 5 2.4 General Description of Equipment under Test (EUT)................................................................................................... 5 3. Test Requirement ................................................................................................................................................................................. 6 3.1 Assessment Result ............................................................................................................................................................... 7 3.2 Test Set-up Photo .................................................................................................................................................................. 8 Test Report Number: BTF-SZ230306R-002 Total or partial reproduction of this document without permission of the Laboratory is not allowed. Page 4 of 9 BTF Testing Lab (Shenzhen) Co., Ltd. F101, 201 and 301, Building 1, Block 2, Tantou Industrial Park, Tantou Community, Songgang Street, Bao'an District, Shenzhen, China 1. Introduction 1.1 Identification of Testing Laboratory Company Name: BTF Testing Lab (Shenzhen) Co., Ltd. Address: F101, 201 and 301, Building 1, Block 2, Tantou Industrial Park, Tantou Community, Songgang Street, Bao'an District, Shenzhen, China Phone Number: +86-0755-23146130 Fax Number: +86-0755-23146130 1.2 Identification of the Responsible Testing Location Test Location: BTF Testing Lab (Shenzhen) Co., Ltd. Address: F101, 201 and 301, Building 1, Block 2, Tantou Industrial Park, Tantou Community, Songgang Street, Bao'an District, Shenzhen, China Description: All measurement facilities used to collect the measurement data are located at F101,201 and 301, Building 1, Block 2, Tantou Industrial Park, Tantou Community, Songgang Street, Bao'an District, Shenzhen, China FCC Registration Number: 518915 Designation Number: CN1330 1.3 Laboratory Condition Ambient Temperature: 20°C to 25°C Ambient Relative Humidity: 45% to 55% Ambient Pressure: 100 kPa to 102 kPa 1.4 Announcement (1) The test report reference to the report template version v0. …

Text truncated - open the document above for the full version.

Test Report Number: BTF-SZ230306R-001 Radiated Emission (9 kHz -30MHz) Test Report Number: BTF-SZ230306R-001 Radiated Emission (30MHz-1GHz) Conducted Emission (AC Mains)