2AMIN-WPB100Wireless Charge Power Bank

User Guide LevPower M10 FCC This device complies with Part 18 of the FCC Rules. This device complies with Part 15 of the FCC Rules. Operation is subject to the following two conditions: (1) This device may not cause harmful interference, and (2) this device must accept any interference received, including interference that may cause undesired operation. CAUTION: Changes or modifications not expressly approved by the party responsible for compliance could void the user’s authority to operate the equipment. NOTE: This equipment has been tested and found to comply with the limits for a Class B digital device, pursuant to Part 15 of the FCC Rules. These limits are designed to provide reasonable protection against harmful interference in a residential installation. This equipment generates, uses, and can radiate radio frequency energy and, if not installed and used in accordance with the instructions, may cause harmful interference to radio communications. However, there is no guarantee that interference will not occur in a particular installation. If this equipment does cause harmful interference to radio or television reception, which can be determined by turning the equipment off and on, the user is encouraged to try to correct the interference by one or more of the following measures: Reorient or relocate the receiving antenna. Increase the separation between the equipment and receiver. Connect the equipment into an outlet on a circuit different from that to which the receiver is connected. Consult the dealer or an experienced radio/TV technician for help. For FAQs and more information, please visit: zmiusa.c om/s upport @zmiusa @zmiusa @zmius ac orp 7 8910 2345 efficiency and shortens the charge time, but also reduces the risk of potential damage to your device and power bank. Be in charge. Anytime. Anywhere. 18-Month L imited Warranty Web: zmiusa.c om/s upport Email: s [email protected] om Phone: +1 (844) 828-2302 ZMI USA Corporation, 120 San Lucar Ct, Sunnyvale, CA 94086-5213, USA The product has an 18-month limited warranty, unless the warranty is voided by one or more of the following: Unauthorized repair, incorrect use, drop, negligence, abuse, liquid damage, accident, alteration, improper use with non-ZMI- branded accessories, or removing or altering product labeling Warranty expiration Customer Service 印刷颜色：PANTONE COOL GRAY 11C K100 材质：105克金东太空梭无光铜，上水性哑油 V1.0 建立 2020/02/17 WPB100美版 说明书 凌浩 V2.0 V3.0 PANTONE 519C ● Get to know your LevPower M10 Low Power charging mode: Double-press the battery level check button to charge low power devices such as smartwatches, Bluetooth headphones, and fitness trackers. Over the course of Low Power charging, the battery level indicator lights will flash in a circular pattern (1, 2, 3, 4, 1, 2...). To exit the mode, single-press the button or wait until a two- hour limit is reached. Quick Start Guide Tip: Using a quality charge/sync cable not only improves energy 6 Warning Please read all instructions and warnings before first use, including charging/recharging instructions and information on the operating temperature range. Improper use of this product may result in product damage, excess heat, fire, and other hazards. Do not short-circuit, bend, crush, puncture, heat, incinerate, or disassemble the product. Avoid mechanical shock and drop impact. Do not expose the product to temperatures above 140° F (60° C). Keep the product away from heat sources, direct sunlight, combustible material, moisture, and liquids. The product will generate heat when charging. Always charge in a cool, well-ventilated area. Do not use the product if it is bloated, deformed, wet, or otherwise damaged. Do not place cards with magnetic stripes or IC chips, such as ID cards, credit cards, and bank cards, in the vicinity of the wireless charger. Keep medical implants, including but not limited to cardiac pacemakers and cochlear implants, at least 1 foot (or 30.48 cm) away from the wireless charger in order to avoid interference with the function of those medical implants. Product usage by children should be under adult supervision. This product is not a toy for children; please store it in a secure place where children cannot reach. Do not use the phone while it is wirelessly charging on the charging pad. Notice Fully charge the power bank before first use. Do not put a full or depleted battery in extended storage. To preserve the lifespan of the power bank, keep the battery level between 25% to 50% and store it in a cool, dry place when not in use. The maximum effective distance between the phone and wireless charging pad is 4 mm. Remove your phone’s protective bumper or case if necessary. If the blue indicator light flashes rapidly, make sure there are no metal objects (coins, ring stand, finger grip, car mount, chip cards, etc.) on the charging pad. ● Check the battery level of your LevPower M10 Press the battery level check button, and the battery level indicator lights will display according to the following table: 1 ● Charge your smartphones, tablets, or other USB devices Connect your mobile device to the USB-A or USB-C port on the battery pack with a quality charge cable. Over the course of charging, the battery level indicator lights will flash in unison following the patterns as defined in the preceding table under Section “Check the battery level of your LevPower M10”. NOTE: The battery level check button is not a typical ON/OFF switch. A single press will wake up the power bank from sleep. To turn off the power bank, 1) unplug all cables from its ports and remove wirelessly chargeable devices; 2) then press the button one time, and the power bank will shut off in 1 minute. Model: WPB100 ZMI LevPower M10 Wireless USB-C Power Bank 70mm 110mm USB-A port (output) USB-C port (input/output) Lightning port (input) Battery level check button Battery level indicator lights Wireless charging indicator USB-A Specifications WPB100 Lithium polymer 10,000mAh 3.7V 37Wh 5,800mAh (…

Text truncated - open the document above for the full version.

Cover Letter for Wireless Charger Date:2019-08-16 Dear Sir/Madam, There’s a Wireless Charge Power Bank, that would like to have your authorization as an Inductive wireless power transfer applications approval. The specific product as below Wireless Desk Charger with its designed features and specified description, meets special requirements for KDB 680106 D01 section 5 b) requirements. Applicant: ZIMI CORPORATION Product Description: Wireless Charge Power Bank Model No: WPB100 FCC ID: 2AMIN-WPB100 Requirement Technical Result 1) Power transfer frequency is less that 1 MHz 110-205KHz Complied 2) Output power from each primary coil is less than 15 watts 10W Complied 3) The transfer system includes only single primary and secondary coils. This includes charging systems that may have multiple primary coils and clients that are able to detect and allow coupling only between individual pairs of coils Single coils Complied 4) Client device is inserted in or placed directly in contact with the transmitter Placed directly in transmitter Complied 5) Mobile exposure conditions only Mobile Complied 6) Aggregate leakage fields at 15 cm surrounding the device and 20cm above the top surface from all simultaneous transmitting coils are demonstrated to be less than 50% of the MPE limit. Reference MPE report Complied Sincerely, Signature: Printed Name: Guodong Jia Position/Title: Certification engineer

ZIMI CORPORATION Date: 08/16/2019 TO: Federal Communication Commission Equipment Authorization Branch 7435 Oakland Mills Road Columbia, MID 21046 Regarding: FCC ID: 2AMIN-WPB100 To whom it may concern: We, the undersigned, hereby authorize Parlam Zhan to act on our behalf in all manners relating to application for equipment authorization with respect to the FCC ID above, including signing of all documents relating to these matters. Any and all acts carried out by the agent on our behalf shall have the same effect as acts of our own. We, the undersigned, hereby certify that we are not subject to a denial of federal benefits, that includes FCC benefits, pursuant to Section 5301 of the Anti-Drug Abuse Act of 1988, 21 U.S.C. 853(a). Where our agent signs the application for certification on our behalf, I acknowledge that all responsibility for complying with the terms and conditions for Certification, as specified by SGS North America, Inc., still resides with < ZIMI CORPORATION >. This authorization is valid until further written notice from the applicant. Name (Printed): Guodong Jia Title: Quality Director Signature: On behalf of Company: ZIMI CORPORATION

ZIMI CORPORATION To: SGS North America Inc. 620 Old Peachtree Road SUITE 100 Suwanee, Georgia United States From: ZIMI CORPORATION Room A913, 159 Chengjiang Road Jiangyin City ,Jiangsu Province,P.R..China Regarding: Confidentiality Request regarding application for FCC ID: 2AMIN-WPB100 LONG TERM CONFIDENTIALITY Pursuant to 47 CFR Section 0.459 and 0.457 of the commission’s rules, the applicant hereby request confidential treatment of the documents listed below, associated with the certification application referenced above. Schematic(s) Block Diagrams Operational Descriptions The documents above contain proprietary information not released to the public. Public disclosure of this information may prove harmful to the business of the applicant. . Sincerely, Signature: ZIMI CORPORATION

SGS-CSTC Standards Technical Services Co., Ltd. Shanghai Branch Page: 1 of 3 Page 1 of 3 External Photos Applicant: ZIMI CORPORATION Address of Applicant: Room A913, No.159 Chengjiang Road, Jiangyin City, Jiangsu Province, 214431, P.R.C Equipment Under Test (EUT): Product Name: Wireless Charge Power Bank Model No.: WPB100 SGS-CSTC Standards Technical Services Co., Ltd. Shanghai Branch Page: 2 of 3 Page 2 of 3 SGS-CSTC Standards Technical Services Co., Ltd. Shanghai Branch Page: 3 of 3 Page 3 of 3 End

Remark：The product is small to place the FCC statement on the product and it be placed in the user manual which the device is marketed. Label Location

SGS-CSTC Standards Technical Services Co., Ltd. Shanghai Branch Page: 1 of 8 Page 1 of 8 Internal Photos Applicant: ZIMI CORPORATION Address of Applicant: Room A913, No.159 Chengjiang Road, Jiangyin City, Jiangsu Province, 214431, P.R.C Equipment Under Test (EUT): Product Name: Wireless Charge Power Bank Model No.: WPB100 SGS-CSTC Standards Technical Services Co., Ltd. Shanghai Branch Page: 2 of 8 Page 2 of 8 SGS-CSTC Standards Technical Services Co., Ltd. Shanghai Branch Page: 3 of 8 Page 3 of 8 SGS-CSTC Standards Technical Services Co., Ltd. Shanghai Branch Page: 4 of 8 Page 4 of 8 SGS-CSTC Standards Technical Services Co., Ltd. Shanghai Branch Page: 5 of 8 Page 5 of 8 SGS-CSTC Standards Technical Services Co., Ltd. Shanghai Branch Page: 6 of 8 Page 6 of 8 SGS-CSTC Standards Technical Services Co., Ltd. Shanghai Branch Page: 7 of 8 Page 7 of 8 SGS-CSTC Standards Technical Services Co., Ltd. Shanghai Branch Page: 8 of 8 Page 8 of 8 End

SGS-CSTC Standards Technical Services Co., Ltd. Shanghai Branch Report No.: SHEM190801620002 Page: 1 of 16 Parlam Zhan E&E Section Manager The manufacturer should ensure that all products in series production are in conformity with the product sample detailed in this report. If the product in this report is used in any configuration other than that detailed in the report, the manufacturer must ensure the new system complies with all relevant standards. Any mention of SGS International Electrical Approvals or testing done by SGS International Electrical Approvals in connection with, distribution or use of the product described in this report must be approved by SGS International Electrical Approvals in writing. Human Exposure Report Application No.: SHEM1908016200CR FCC ID: 2AMIN-WPB100 Applicant: ZIMI CORPORATION Address of Applicant: Room A913, No.159 Chengjiang Road, Jiangyin City, Jiangsu Province, 214431, P.R.C Manufacturer: ZIMI CORPORATION Address of Manufacturer: Room A913, No.159 Chengjiang Road, Jiangyin City, Jiangsu Province, 214431, P.R.C Factory: 1, Dongguan DBK Energy Technology Co.,Ltd. 2, Tianjin Zowee Technology Development Co., Limited 3, Kunshan Xuanchuang Electronic Co., Ltd. Address of Factory: 1, No.51 Zhangshen Middle Road,Xuzhen Community,Zhangmutou Town,Dongguan,Guangdong,P.R.China. 2, No.71 South Street Xinhuan.West Zone.Economic Development Zone of Tianjin,Tianjin,China. 3, No.218 Changxing Ease Road, Zhoushi Town, KunShan City, Jiangsu Province, 215300, P.R.C. Equipment Under Test (EUT): EUT Name: Wireless Charge Power Bank Model No.: WPB100 Standards: 47 CFR PART 1, Subpart I, Section 1.1310 KDB 680106 Date of Receipt: 2019-08-14 Date of Test: 2019-09-17 to 2019-09-22 Date of Issue: 2019-09-25 Test Result : Pass* * In the configuration tested, the EUT complied with the standards specified above. SGS-CSTC Standards Technical Services Co., Ltd. Shanghai Branch Report No.: SHEM190801620002 Page: 2 of 16 Revision Record Version Description Date Remark 00 Original 2019-09-25 / Authorized for issue by: Bill Wu / Project Engineer Parlam /Reviewer SGS-CSTC Standards Technical Services Co., Ltd. Shanghai Branch Report No.: SHEM190801620002 Page: 3 of 16 2 Contents Page 1 COVER PAGE ............................................................................................................................................ 1 2 CONTENTS .............................................................................................................................................................. 3 3 GENERAL INFORMATION .................................................................................................................................... 4 3.1 DETAILS OF E.U.T. ..................................................................................................................................................... 4 3.2 DESCRIPTION OF SUPPORT UNITS ............................................................................................................................... 4 3.3 TEST LOCATION .......................................................................................................................................................... 4 3.4 TEST FACILITY ............................................................................................................................................................ 5 3.5 DEVIATION FROM STANDARDS ................................................................................................................................... 5 3.6 ABNORMALITIES FROM STANDARD CONDITIONS ........................................................................................................ 5 4 EQUIPMENTS USED DURING TEST .................................................................................................................. 6 5 TEST RESULTS ...................................................................................................................................................... 7 5.1 RF EXPOSURE TEST .................................................................................................................................................... 7 E.U.T. Operation ...................................................................................................................................................... 7 Operating Environment: .......................................................................................................................................... 7 EUT Operation:......................................................................................................................................................... 7 Measurement Data: ................................................................................................................................................. 8 6 PHOTOGRAPHS ................................................................................................................................................... 14 6.1 TEST PHOTOS ............................................................................................................................................................ 14 SGS-CSTC Standards Technical Services Co., Ltd. Shanghai Branch Report No.: SHEM190801620002 Page: 4 of 16 3 General Information 3.1 Details of E.U.T. Power supply: DC 3.7V 10000mAh rechargeable battery Input: DC 5V 3A; 9V 2A; 12V 1.5A by USB-C DC 5V 2.4A by Lightning Output:DC 5V 3A; 9V 2A; 12V 1.5A by USB-C only DC 5V 2.1A by USB-A only DC 5V 3A by USB-A & USB-C Wireless & cable charging simultaneously output: Wireless: 5W USB-A only: 5V 2.1A USB-C only: 5V 2.5A USB-A & USB-C: 5V 2.1A (USB-A); 5V 1A (USB-C) Wireless charging only: 5W/7.5W/10W Cable: Lightning cable 40cm Operation frequency: 110-205 kHz Antenna type: Inductive Loop Coil Antenna Remark: Tests were conducted in three loads and the worst case is reported only. 3.2 Description of Support Units The EUT has been te…

Text truncated - open the document above for the full version.

SGS-CSTC Standards Technical Services Co., Ltd. Shanghai Branch Report No.: SHEM190801620001 Page: 1 of 20 Parlam Zhan E&E Section Manager The manufacturer should ensure that all products in series production are in conformity with the product sample detailed in this report. If the product in this report is used in any configuration other than that detailed in the report, the manufacturer must ensure the new system complies with all relevant standards. Any mention of SGS International Electrical Approvals or testing done by SGS International Electrical Approvals in connection with, distribution or use of the product described in this report must be approved by SGS International Electrical Approvals in writing. TEST REPORT Application No.: SHEM1908016200CR FCC ID: 2AMIN-WPB100 Applicant: ZIMI CORPORATION Address of Applicant: Room A913, No.159 Chengjiang Road, Jiangyin City, Jiangsu Province, 214431, P.R.C Manufacturer: ZIMI CORPORATION Address of Manufacturer: Room A913, No.159 Chengjiang Road, Jiangyin City, Jiangsu Province, 214431, P.R.C Factory: 1, Dongguan DBK Energy Technology Co.,Ltd. 2, Tianjin Zowee Technology Development Co., Limited 3, Kunshan Xuanchuang Electronic Co., Ltd. Address of Factory: 1, No.51 Zhangshen Middle Road,Xuzhen Community,Zhangmutou Town,Dongguan,Guangdong,P.R.China. 2, No.71 South Street Xinhuan.West Zone.Economic Development Zone of Tianjin,Tianjin,China. 3, No.218 Changxing Ease Road, Zhoushi Town, KunShan City, Jiangsu Province, 215300, P.R.C. Equipment Under Test (EUT): EUT Name: Wireless Charge Power Bank Model No.: WPB100 Standard(s) : 47 CFR Part 18 Date of Receipt: 2019-08-14 Date of Test: 2019-09-17 to 2019-09-22 Date of Issue: 2019-09-25 Test Result: Pass* * In the configuration tested, the EUT complied with the standards specified above. SGS-CSTC Standards Technical Services Co., Ltd. Shanghai Branch Report No.: SHEM190801620001 Page: 2 of 20 Revision Record Version Description Date Remark 00 Original 2019-09-25 / Authorized for issue by: Bill Wu / Project Engineer Parlam /Reviewer SGS-CSTC Standards Technical Services Co., Ltd. Shanghai Branch Report No.: SHEM190801620001 Page: 3 of 20 2 Test Summary Emission Part Item Standard Method Requirement Result Radiated Emissions (30MHz-1GHz) 47 CFR Part 18 FCC OST/MP-5:1986 Part 18.305 Pass Radiated Emissions (Magnetic field Strength) (9kHz- 30MHz) 47 CFR Part 18 FCC OST/MP-5:1986 Class B Pass SGS-CSTC Standards Technical Services Co., Ltd. Shanghai Branch Report No.: SHEM190801620001 Page: 4 of 20 3 Contents Page 1 COVER PAGE ............................................................................................................................................. 1 2 TEST SUMMARY ......................................................................................................................................... 3 3 CONTENTS .................................................................................................................................................. 4 4 GENERAL INFORMATION ......................................................................................................................... 5 4.1 DETAILS OF E.U.T. ................................................................................................................................ 5 4.2 DESCRIPTION OF SUPPORT UNITS........................................................................................................... 5 4.3 MEASUREMENT UNCERTAINTY ................................................................................................................ 5 4.4 TEST LOCATION ..................................................................................................................................... 6 4.5 TEST FACILITY ....................................................................................................................................... 6 4.6 DEVIATION FROM STANDARDS ................................................................................................................ 6 4.7 ABNORMALITIES FROM STANDARD CONDITIONS ....................................................................................... 6 5 EQUIPMENT LIST ....................................................................................................................................... 7 6 EMISSION TEST RESULTS ........................................................................................................................ 8 6.1 RADIATED EMISSIONS (30MHZ-1GHZ) ................................................................................................... 8 6.2 RADIATED EMISSIONS (MAGNETIC FIELD STRENGTH) (9KHZ-30MHZ) ..................................................... 16 7 TEST SETUP PHOTOGRAPHS ................................................................................................................ 20 8 EUT CONSTRUCTIONAL DETAILS ......................................................................................................... 20 SGS-CSTC Standards Technical Services Co., Ltd. Shanghai Branch Report No.: SHEM190801620001 Page: 5 of 20 4 General Information 4.1 Details of E.U.T. Power supply: DC 3.7V 10000mAh rechargeable battery Input: DC 5V 3A; 9V 2A; 12V 1.5A by USB-C DC 5V 2.4A by Lightning Output:DC 5V 3A; 9V 2A; 12V 1.5A by USB-C only DC 5V 2.1A by USB-A only DC 5V 3A by USB-A & USB-C Wireless & cable charging simultaneously output: Wireless: 5W USB-A only: 5V 2.1A USB-C only: 5V 2.5A USB-A & USB-C: 5V 2.1A (USB-A); 5V 1A (USB-C) Wireless charging only: 5W/7.5W/10W Cable: Lightning cable 40cm Operation frequency: 110-205 kHz Antenna type: Inductive Loop Coil Antenna Remark: Tests were conducted in three loads and the worst case is reported only. 4.2 Description of Support Units Description Manufacturer Model No. Serial No. Load Resistor / / / 4.3 Measurement Uncertainty No. Item Measurement Uncertainty 1 Radio Frequency ±8.4 x 10 -8 2 Timeout ±2s 3 Duty cycle ±0.37% 4 Occupied Ba…

Text truncated - open the document above for the full version.

SGS-CSTC Standards Technical Services Co., Ltd. Shanghai Branch Page: 1 of 3 Page 1 of 3 Test Setup Photos-FCC Applicant: ZIMI CORPORATION Address of Applicant: Room A913, No.159 Chengjiang Road, Jiangyin City, Jiangsu Province, 214431, P.R.C Equipment Under Test (EUT): Product Name: Wireless Charge Power Bank Model No.: WPB100 SGS-CSTC Standards Technical Services Co., Ltd. Shanghai Branch Page: 2 of 3 Page 2 of 3 1 Contents Page 1 CONTENTS............................................................................................................... 2 2 EQUIPMENT UNDER TEST PICTURES ............................................................. 3 2.1 Spurious emissions ........................................................................................... 3 SGS-CSTC Standards Technical Services Co., Ltd. Shanghai Branch Page: 3 of 3 Page 3 of 3 2 EQUIPMENT UNDER TEST PICTURES 2.1 Spurious emissions Below 30MHz 30MHz-1GHz End