2AMRO-VLXPCG501Power Bank

FCC Warning This device complies with Part 15 of the FCC Rules. Operation is subject to the following two conditions: (1) This device may not cause harmful interference, and (2) this device must accept any interference received, including interference that may cause undesired operation. NOTE 1: This equipment has been tested and found to comply with the limits for a Class B digital device, pursuant to part 15 of the FCC Rules. These limits are designed to provide reasonable protection against harmful interference in a residential installation. This equipment generates, uses and can radiate radio frequency energy and, if not installed and used in accordance with the instructions, may cause harmful interference to radio communications. However, there is no guarantee that interference will not occur in a particular installation. If this equipment does cause harmful interference to radio or television reception, which can be determined by turning the equipment off and on, the user is encouraged to try to correct the interference by one or more of the following measures: - Reorient or relocate the receiving antenna. - Increase the separation between the equipment and receiver. -Connect the equipment into an outlet on a circuit different from that to which the receiver is connected. -Consult the dealer or an experienced radio/TV technician for help. NOTE 2: Any changes or modifications to this unit not expressly approved by the party responsible for compliance could void the user's authority to operate the equipment. The device has been evaluated to meet general RF exposure requirement. The device can be used in portable exposure condition without restriction.

Rev 1/26/2023 iOttie, Inc. Federal Communications Commission Authorization and Evaluation Division 7435 Oakland Mills Road Columbia, MD 21046 USA Date: 12-27-2025 Ref: Attestation Statements Part 2.911(d)(5)(i) Filing FCC ID: 2AMRO-VLXPCG501 [iOttie, Inc.] certifies that the equipment for which authorization is sought is not “covered” equipment prohibited from receiving an equipment authorization pursuant to section 2.903 of the FCC rules. [iOttie, Inc.] certifies that the equipment for which authorization is sought does not include cybersecurity or anti-virus software produced or provided by Kaspersky Lab, Inc. or any of its successors and assignees, including equipment with integrated Kaspersky Lab, Inc. (or any of its successors and assignees) cybersecurity or anti-virus software pursuant to DA-24-886 and KDB 986446 D01 Covered Equipment Guidance section B(2a). Device is inherently compliant based on hardware limitations or software controls. or A Software Bill of Materials (SBOM) is provided to the TCB for review, and The end-user or third parties cannot install additional software on this device. Sincerely, Signature： By: caleb cho Rev 1/26/2023 iOttie, Inc. Federal Communications Commission Authorization and Evaluation Division 7435 Oakland Mills Road Columbia, MD 21046 USA Date: 12-27-2025 Ref: Attestation Statements Part 2.911(d)(5)(ii) Filing FCC ID: 2AMRO-VLXPCG501 [iOttie, Inc.] certifies that, as of the date of the filing of the application, the applicant is not identified on the Covered List (as a specifically named entity or any of its subsidiaries or affiliates) as an entity producing “covered” equipment. Sincerely, Signature： By: caleb cho

iOttie, Inc. U.S. Agent Letter of Attestation To: Federal Communications Commission 7435 Oakland Mills Road, Columbia, MD 21046, USA Date: 12-27-2025 Ref: Attestation Statement – Part 2.911(d)(7) filing FCC ID: 2AMRO-VLXPCG501 iOttie, Inc. (“the applicant”) certifies that, as of the date of the filing of the application, iOttie, Inc. (“the agent”) is our designated U.S. agent for service of process for the above reference FCC ID. The applicant accepts to maintain an agent for service of process in the United States for no less than one year after either the grantee has permanently terminated all marketing and importation of the applicable equipment within the U.S., or the conclusion of any Commission-related administrative or judicial proceeding involving the equipment, whichever is later. The applicant further acknowledges it is our responsibility to inform the FCC whenever the agent information changes. iOttie, Inc. ("the agent) understand it is the agent's obligation to accept service of process in the United States for matters related to the applicable equipment, and at the physical U.S. address and email address. Designated U.S. Agent Company Name: iOttie, Inc. FRN: 0026656165 Address: 470 7th Avenue, 6 FL, New York New York United States 10018 Signature: Contact Person: caleb cho Tel: 201-580-2685 Email: [email protected] Applicant Company Name: iOttie, Inc. FRN: 0026656165 Address: 470 7th Avenue, 6 FL, New York New York United States 10018 Signature: Contact Person: caleb cho Tel: 201-580-2685 Email: [email protected]

iOttie, Inc. Date: December 27, 2025 Product Model Number: VLXPCG501BT FCC ID: 2AMRO-VLXPCG501 To whom it may concern, Re: Product Certification Representative Authorization Letter We authorize QAI Laboratories Ltd. 3980 North Fraser Way, Burnaby B.C. Canada V5J 5K5 to act on our behalf on all matters concerning the above named equipment. This shall include the following: • Testing • Approval applications and procedures We declare that QAI Laboratories Ltd. is allowed to forward all information related to the approval project to the applied certification body and to the notification entities and to discuss any issues concerning the approval application. Any and all acts carried out by QAI Laboratories Ltd. on our behalf shall have the same effect as acts of our own. Contact Listed on FCC Wesbite Signature： By: caleb cho Title: Manager Email: [email protected] Telephone: 201-580-2685 On behalf of: iOttie, Inc.

iOttie, Inc. Office of Engineering Technology Federal Communications Commission 7435 Oakland Mills Road Columbia, MD 21046 USA Date: December 27, 2025 Subject; Request for Confidentiality FCC ID: 2AMRO-VLXPCG501 To Whom It May Concern, Pursuant to the provisions of the Commission’s rules Title 47 Sections §0.457 and §0.459, we are requesting the Commission to withhold the following attachment(s) as confidential documents from public disclosure indefinitely. These documents contain detailed system and equipment descriptions and are considered as proprietary information in operation of the equipment. The public disclosure of these documents might be harmful to our company and would give competitors an unfair advantage in the market. Schematic Diagram Block Diagram Parts List Operational Description Tune-up Procedure Software Security Requirements for UNII devices It is our understanding that all measurement test reports, FCC ID label format and correspondence during the certification review process cannot be granted as confidential documents and this information will be available for public review once the grant of equipment authorization is issued. Sincerely, Signature： By: caleb cho Title: Manager

Fine Page 1 of 4 承 認 書 SPECIFICATION FOR APPROVAL 客 戶： CUSTOMER: 客 戶 料 號： CUST P/N: 豪辉 料 號： FINE P/N: G43.5 Dual Slot-6.SUH Single Coil 0.08*24P*2*10TS 産 品 型 號： DESC: Φ43.5MMX5.0MMX0.6MM PC95 日 期： DATE: 2023/12/23 版 本： Version: A.0 擬制 PREPARED BY 審核 CHECKED BY 批准 APPROVED BY 客戶承認 CUSTOMER APPROVE Manufacturer..........................: iOttie, Inc. Address of Manufacturer........: 470 7th Avenue, 6 FL, New York New York United States 10018 Fine Page 2 of 4 版本變更履歷 Version Change History 版本 Rev. 變 更 前 Before Change 變 更 後 After Change 更 改 日 期 Change Date 批 准 Approved By A.0 新发行 ---- 2023/12/23 Fine Page 3 of 4 SPECIFICATION 産 品 型 號： DESC Φ20.5x40-6.5uH-0.15x18-15mm- 版本 Rev：A.0 客戶CUST: 客户料号CUST P/N: 一、尺寸DIMENSION:(mm) 二、原理图SCHEMATIC DIAGRAM: A 38.50±1.5 B 20.5±0.5 C 1.25 Max D 15±2 E 4±2 F 43.5±1 G 10.0 ref H 1.6 Max I 5.3 ref 三、绕线参数Winding Specification: 序号 NO. 端子 TERMINAL 线径 WIRE 圈数 Turns 绕线方向 Winding Direction 1 S F 漆包线0.08*24*2 10Ts CCW 四、电气特性ELECTRICAL CHARACTERISTICS: 温度TEMPERATURE:25±10°C, 湿度RELATIVE HUMIDITY:65±20% 序号 NO. 项目 ITEM 端子 TERMINAL 标准 SPECIFICATION 测试条件 TEST FREQUENCY 测试仪器 TEST EQUIPMENTS 1 IND. S-F 3.8uH ±20%单独线圈 100KHz/1.0V LCZ METER 1062B 2 IND. S-F 6.3uH ±10%加磁片 100KHz/1.0V LCZ METER 1062B 3 DCR S-F ≤50mΩ LCZ METER 502B 擬制/日期PREPARED BY/DATE 審核/日期CHECKED BY/DATE

Report No: DSP25112644-1E FCC ID: 2AMRO-VLXPCG501 Annex of Test Report Annex A. EUT External Photos VLXPCG501BT EUT View 1 EUT View 2 Report No: DSP25112644-1E FCC ID: 2AMRO-VLXPCG501 Annex of Test Report EUT View 3 EUT View 4 Report No: DSP25112644-1E FCC ID: 2AMRO-VLXPCG501 Annex of Test Report EUT View 5 EUT View 6 Report No: DSP25112644-1E FCC ID: 2AMRO-VLXPCG501 Annex of Test Report EUT View 7

Report No: DSP25112644-1E FCC ID: 2AMRO-VLXPCG501 Annex of Test Report Annex D. Label and Information FCC Label Sample FCC Labe Size: 3cm x 2cm FCC Label Specifications Text is Black in color and is justified. Labels are printed in indelible ink on permanent adhesive backing or silk-screened onto the EUT or shall be affixed at a conspicuous location on the EUT. Where the EUT is constructed in two or more sections connected by wires and marketed together, the above statement is required to be affixed only to the main control unit. When the EUT is so small or for such use that it is not practicable to place the statement on it, the above information shall be placed in a prominent location in the instruction manual or pamphlet supplied to the user or, alternatively, shall be placed on the container in which the device is marketed. FCC Label Location Label

Report No: DSP25112644-1E FCC ID: 2AMRO-VLXPCG501 Annex of Test Report Annex B. EUT Internal Photos VLXPCG501BT EUT View 1 EUT View 2 Coil ANT1 Report No: DSP25112644-1E FCC ID: 2AMRO-VLXPCG501 Annex of Test Report EUT View 3 EUT View 4 Report No: DSP25112644-1E FCC ID: 2AMRO-VLXPCG501 Annex of Test Report EUT View 5

Report No: DSP25112644-2H MPE Test Report Page 1 of 14 MPE Test Report FCC ID: 2AMRO-VLXPCG501 Report No. : DSP25112644-2H Applicant : iOttie, Inc. Product Name : Power Bank Model Name : VLXPCG501BT Test Standard : FCC CFR 47 PART 1, 1.1310 Date of Issue : 2025-12-27 Shenzhen CCUT Quality Technology Co., Ltd. 1F, Building 35, Changxing Technology Industrial Park, Yutang Street, Guangming District, Shenzhen, Guangdong, China; (Tel.:+86-755-23406590 website: www.ccuttest.com) This test report is limited to the above client company and the product model only. It may not be duplicated without prior permitted by Shenzhen CCUT Quality Technology Co., Ltd. Report No: DSP25112644-2H MPE Test Report Page 2 of 14 Test Report Basic Information Applicant..................................: Dongguan Innosmart Electronics Co., Ltd. Address of Applicant...............: Room 401, Building 2, No. 9 Heshun Road, Shatou Community, Chang'an Town, Dongguan City, GuangDong province Manufacturer..........................: Dongguan Innosmart Electronics Co., Ltd. Address of Manufacturer........: Room 401, Building 2, No. 9 Heshun Road, Shatou Community, Chang'an Town, Dongguan City, GuangDong province Product Name.........................: iOttie, Inc. Brand Name.............................: 470 7th Avenue, 6 FL, New York New York United States 10018 Main Model..............................: Series Models..........................: iOttie, Inc. Test Standard..........................: FCC CFR 47 PART 1, 1.1310 KDB 680106 D01 Wireless Power Transfer v04 Date of Test .............................: 2025-11-26 to 2025-12-27 Test Result...............................: PASS Tested By ................................: (Colin Chen) Reviewed By............................: (Lorzix Luo) Authorized Signatory............: (Lahm Peng) Note : This test report is limited to the above client company and the product model only. It may not be duplicated without prior permitted by Shenzhen CCUT Quality Technology Co., Ltd.. All test data presented in this test report is only applicable to presented test sample. Report No: DSP25112644-2H MPE Test Report Page 3 of 14 CONTENTS 1. General Information ....................................................................................................................................................5 1.1 Product Information .............................................................................................................................................5 1.2 Test Setup Information..........................................................................................................................................6 1.3 Test Facilities ........................................................................................................................................................7 1.4 List of Measurement Instruments ..........................................................................................................................7 1.5 Measurement Uncertainty .....................................................................................................................................7 2. RF Exposure .................................................................................................................................................................8 2.1 Standard and Limit................................................................................................................................................8 2.2 Test Procedures ....................................................................................................................................................8 2.3 Test Setup Block Diagram ......................................................................................................................................9 2.4 Test Data and Results .......................................................................................................................................... 10 Annex A. Test Photos ..................................................................................................................................................... 12 Report No: DSP25112644-2H MPE Test Report Page 4 of 14 Revision History Revision Issue Date Description Revised By V1.0 2025-12-27 Initial Release Lahm Peng Report No: DSP25112644-2H MPE Test Report Page 5 of 14 1. General Information 1.1 Product Information Product Name: Power Bank Trade Name: iOttie Test Model: VLXPCG501BT Series Models: - Rated Voltage: USB-C Input voltage/current: 5V⎓3A, 9V⎓2A USB-C Output Power: 5V⎓3A, 9V⎓2.22A, 12V⎓1.67A, Wireless Output: 5W, 7.5W, 10W, 15W Power Adapter: - Battery: DC 3.85V, 5000mAh, 19.25Wh Test Sample No: DSP25112644-1 Hardware Version: V1.0 Software Version: V1.0 Note 1: The test data is gathered from a production sample, provided by the manufacturer. Wireless Specification Wireless Standard: WPC (QI) Operating Frequency: Wireless charging Output :110.5kHz-205kHz Modulation: FSK Antenna Gain: 0dBi Type of Antenna: Coil Antenna Type of Device: Portable Device Mobile Device Modular Device Report No: DSP25112644-2H MPE Test Report Page 6 of 14 1.2 Test Setup Information List of Test Modes Test Mode Description Remark TM1 Wireless charging 5W - TM2 Wireless charging 7.5W - TM3 Wireless charging 10W - TM4 Wireless charging 15W - TM5 Wireless charging 5W+Charging - Note 1: All modes above have been tested and only the worst modes: TM4, data are represented in the report. Note 2: The adapter charging mode only supports 5W output. List and Details of Auxiliary Cable Description Length (cm) Shielded/Unshielded With/Without Ferrite USB cable 100 Unshielded Without Ferrite - - - - List and Details of Auxiliary Equipment Description Manufacturer Model Serial Number Adapter XIAOMI MDY-14-EU HC78E2N6A23645 Phone iPhone iPhone 16pro - Report No: DSP25112644-2H MPE Test Report Page 7 of 14 1.3 Test Facilities Laboratory Name: Shenzhen CCUT Qualit…

Text truncated - open the document above for the full version.

Report No: DSP25112644-1E FCC Test Report Page 1 of 27 FCC TEST REPORT FCC ID: 2AMRO-VLXPCG501 Report No. : DSP25112644-1E Prepared For : iOttie, Inc. Product Name : Power Bank Model Name : VLXPCG501BT FCC Rule : FCC Part 15 Subpart C Date of Issue : 2025-12-30 Shenzhen CCUT Quality Technology Co., Ltd. 1F, Building 35, Changxing Technology Industrial Park, Yutang Street, Guangming District, Shenzhen, Guangdong, China; (Tel.:+86-755-23406590 website: www.ccuttest.com) This test report is limited to the above client company and the product model only. It may not be duplicated without prior permitted by Shenzhen CCUT Quality Technology Co., Ltd. Report No: DSP25112644-1E FCC Test Report Page 2 of 27 Test Report Basic Information Applicant..................................: iOttie, Inc. Address of Applicant...............: 470 7th Avenue, 6 FL, New York New York United States 10018 Manufacturer..........................: iOttie, Inc. Address of Manufacturer........: 470 7th Avenue, 6 FL, New York New York United States 10018 Product Name.........................: Power Bank Brand Name.............................: iOttie Main Model..............................: VLXPCG501BT Series Models..........................: - Test Standard..........................: FCC Part 15 Subpart C ANSI C63.4-2014 ANSI C63.10-2020 Date of Test .............................: 2025-11-26 to 2025-12-30 Test Result...............................: PASSED Tested Engineer ....................: (Colin Chen) Project Manager......................: (Lorzix Luo) Authorized Signatory............: (Lahm Peng) Note : This test report is limited to the above client company and the product model only. It may not be duplicated without prior permitted by Shenzhen CCUT Quality Technology Co., Ltd.. All test data presented in this test report is only applicable to presented test sample. Report No: DSP25112644-1E FCC Test Report Page 3 of 27 CONTENTS 1. General Information ....................................................................................................................................................5 1.1 Product Information .............................................................................................................................................5 1.2 Test Setup Information..........................................................................................................................................6 1.3 Compliance Standards ...........................................................................................................................................7 1.4 Test Facilities ........................................................................................................................................................7 1.5 List of Measurement Instruments ..........................................................................................................................8 1.6 Measurement Uncertainty .....................................................................................................................................8 2. Summary of Test Results .............................................................................................................................................9 3. Antenna Requirement ............................................................................................................................................... 10 3.1 Standard and Limit.............................................................................................................................................. 10 3.2 Test Result .......................................................................................................................................................... 10 4. Conducted Emissions ................................................................................................................................................ 11 4.1 Standard and Limit.............................................................................................................................................. 11 4.2 Test Procedure.................................................................................................................................................... 11 4.3 Test Data and Results .......................................................................................................................................... 12 5. Radiated Emissions ................................................................................................................................................... 15 5.1 Standard and Limit.............................................................................................................................................. 15 5.2 Test Procedure.................................................................................................................................................... 15 5.3 Test Data and Results .......................................................................................................................................... 17 6. Occupied Bandwidth ................................................................................................................................................. 26 6.1 Standard and Limit.............................................................................................................................................. 26 6.2 Test Procedure.................................................................................................................................................... 26 6.3 Test Data and Results .......................................................................................................................................... 27 Report No: DSP25112644-1E FCC Test Report Page 4 of 27 Revision History Revision Issue Date Description Revised By V1.0 2025-12-30 Initial Release Lahm Peng Report No: DSP2511264…

Text truncated - open the document above for the full version.

Report No: DSP25112644-1E FCC ID: 2AMRO-VLXPCG501 Annex of Test Report Annex C. Test Photos Conducted Emission Test View 1 Radiated Emission Test View 1 Report No: DSP25112644-1E FCC ID: 2AMRO-VLXPCG501 Annex of Test Report Radiated Emission Test View 2 Radiated Emission Test View 3 Report No: DSP25112644-1E FCC ID: 2AMRO-VLXPCG501 Annex of Test Report Radiated Emission Test View 4