2AN8F-MSLM2011QWireless power bank

Wireless power bank Instruction Manual MSL-M2011Q，SM-2826 1 x 4,000 mAh Wireless Power Bank 1 x USB to Micro-USB Charging Cable 1 x Instruction Manual 4000mAh/3.7V/14.8Wh Micro-USB input:DC 5V/2A Type-C input:DC 5V/2A USB A output:DC 5V/2A Wireless output:5W Press the Powerbank ON/OFF Button(1) once to view the remaining power capacity. Press the button twice to turn OFF. Charging the Powerbank: Charge the powerbank fully before usage. Connect the provided charging cable to a power source and to the micro-USB Input port(3) or Type-C Input(4) on the powerbank. Once connected the LED Indicator(5) will BLUE color when charging, once fully charged, BLUE LED will stop Charging Electronic Devices with the Power Bank: Connect the charging cable to your mobile phone/device using the appropriate connector. Connect the USB part of the cable to the USB Output(2) port, the LED Indicator will illuminate BLUE when charging. Remove the charging cable from your mobile device when it is fully charged. Charging Electronic Devices with the Wireless Charging: Press the Powerbank ON/OFF button(1) to turn on the wireless charging function, LED indicator will glow green when in standby mode. Place wireless charging supported mobile device on the wireless charging surface(6). The device will automatically begin to charge, LED will glow red when device is charging. Note: When wireless charging, if the LED NOT a wireless charging device or there is an object between the device and charging surface interfering with the charging. process. 1. • • • 2. • • • 3. • • • • ** 1. 2. 3. 4. 5. 6. • • • • • • • Powerbank ON/OFF Button USB Output Micro-USB Input Type-C Input LED Indicator Wireless Charging Surface What’s included: Features: LED Indicators Instructions: MADE IN CHINA WARNING-When using this product, basic precautions should always be followed: Read all the instructions before use. Never store or use this product in temperatures below 32°F(0°C) or above 115°F(45°C). Do not overcharge your phone. The unit may become hot under excessive use. Remove your phone once it is fully charged. Never charge your phone for more than 7 hours at a time. The unit will only achieve full performance after 2 or 3 completed charge and discharge cycles. To reduce the risk of injury, close supervision is required when the product is used near children. Do not expose the device to moisture. Do not use the device in excess of its output rating. Overload outputs above the Do not use the device if damaged or Do not disassemble the device. For professional. incorrect reassembly may or temperatures above 104°F may cause explosion. use only identical replacement parts to ensure product safety. Attachments on the back of your phone can impede the effectiveness of the wireless charger, and lead to overheating. Please remove any attachments from the phone before charging on this device, attachments can interfer with wireless charging and lead to over heating. • 1. 2. 3. 4. 5. 6. 7. 8. 9. 10. 11. 12. 13. SAFETY PRECAUTIONS: 100 6634 FCC Informat on This device complies with Part 15 of the FCC Rules. Caut on: Any changes or modifications not expressly approved could void the user’s authority to operate the equipment. Note: This equipment has been tested and found to comply with the limits for a Class B digital device, pursuant to Part 15 of the FCC Rules. These limits are designed to provide reasonable protection against harmful interference in a residential installation. This equipment generates, uses and can radiate radio frequency energy and, if not installed and used in accordance with the instructions, may cause harmful interference to radio communications. However, there is no guarantee that interference will not occur in a particular installation. If this equipment does cause harmful interference to radio or television reception, which can be determined by turning the equipment off and on, the user is encouraged to try to correct the interference by one or more of the following measures: • Reorient or relocate the receiving antenna. • Increase the separation between the equipment and receiver. Connect the equipment into an outlet on a circuit different from that to whic the receiver is connected. • Consult the dealer or an experienced radio/TV technician for help. This device complies with part 15 of the FCC rules. Operation is subject to the following two conditions (1) this device may not cause harmful interference, and (2)2) th device must accept any interference received, including interference that may cause undesired operation. The device has been evaluated to meet general RF exposure requirement. The device can be used in portable exposure condition without restriction.

ShenZhen Mossloo Industrial Co.,Ltd 2020.11.4 Eurofins MET Labs 914 West Patapsco Avenue Baltimore, MD 21230 RE: CONFIDENTIALITY REQUEST FOR Product Name: Wireless power bank Trademark: N/A Model Number(s): MSL-M2011Q, SM-2826 FCC ID: 2AN8F-MSLM2011Q To Whom It May Concern: This letter serves as an official request for confidentiality under sections 0.457 and 0.459 of CFR 47. We have requested that the - Block Diagram - Schematics - Operational Description required to be submitted with this application be permanently withheld from public review. The above materials contain trade secrets and proprietary information not customarily released to the public. The public disclosure of these materials may be harmful to the applicant and provide unjustified benefits to its competitors. Please contact me if there is any information you may need. Sincerely, Client’s signature: Client’s name / title : Orders Cheng /Manager Contact information / address: Road One No.4, Science Industrial Park, Shangxue Village, Bantian Street, Longgang District, Shenzhen, China

ShenZhen Mossloo Industrial Co.,Ltd 2020.11.4 Eurofins MET Labs 914 West Patapsco Avenue Baltimore, MD 21230 RE: LETTER OF AGENT AUTHORIZATION To Whom It May Concern: We, the undersigned, hereby authorize Shenzhen BCTC Testing Co., Ltd to act on our behalf in all matters relating to application for equipment authorization, including the signing of all documents relating to these matters. We also hereby certify that no party to the application authorized hereunder is subject to the denial of benefits, including FCC benefits, pursuant to Section 5301 of the Anti-Drug Abuse Act of 1988, 21 U.S.C.853(a). This agreement expires one year from the current date. Sincerely, Client’s signature: Client’s name / title : Orders Cheng /Manager Contact information / address: Road One No.4, Science Industrial Park, Shangxue Village, Bantian Street, Longgang District, Shenzhen, China

Shenzhen Mossloo Industrial Co.,Ltd Model Difference 2020-11-4 Product Name: Wireless power bank Trademark: N/A Model Number(s): MSL-M2011Q, SM-2826 FCC ID: 2AN8F-MSLM2011Q All the model are the same circuit and RF module, except model names. Regards Sincerely Client’s signature: Client’s name / title : Orders Cheng /Manager Contact information / address: Road One No.4, Science Industrial Park, Shangxue Village, Bantian Street, Longgang District, Shenzhen, China

External Photos

Size:30*15mm FCC ID: 2AN8F-MSLM2011Q This device complies with Part 15 of the FCC Rules. Operation is subject to the following two conditions:(1)This device may not cause harmful interfer ence, and (2) this device must accept any interference received, including interference that may cause undesired operation. Label Location

Internal Photos Antenna

No.：BCTC/RF-EMC-005Page1of16Edition：A.1 TEST REPORT    Shenzhen BCTC Testing Co., Ltd. ReportNo.: BCTC2010001342-2E Applicant:ShenzhenMosslooIndustrialCo.,Ltd ProductName: Wirelesspowerbank Model/TypeRef.: MSL-M2011Q TestedDate: Oct.23,2020toNov.02,2020 IssuedDate: Nov.03,2020 ReportNo.: BCTC2010001342-2E No.：BCTC/RF-EMC-005Page2of16Edition：A.1 FCC ID: 2AN8F-MSLM2011Q The test report is effective only with both signature and specialized stamp.This result(s) shown in this report refer only to the sample(s) tested. Without written approval of Shenzhen BCTC Testing Co., Ltd, this report can’t be reproduced except in full.The tested sample(s) and the sample information are provided by the client. Product Name: Wireless power bank Trademark: N/A Model/Type Ref.: MSL-M2011Q SM-2826 Prepared For: Shenzhen Mossloo Industrial Co., Ltd Address: Road One No.4, Science Industrial Park, Shangxue Village, Bantian Street, Longgang District, Shenzhen China Manufacturer: Shenzhen Mossloo Industrial Co., Ltd Address: Road One No.4, Science Industrial Park, Shangxue Village, Bantian Street, Longgang District, Shenzhen China Prepared By: Shenzhen BCTC Testing Co., Ltd. Address: 1-2F, East of B Building, Pengzhou Industrial, Fuyuan 1st Road, Qiaotou Community, Fuyong Street, Bao’an District, Shenzhen, China Sample Received Date: Oct. 23, 2020 Sample tested Date: Oct. 23, 2020 to Nov. 02, 2020 Issue Date: Nov. 03, 2020 Report No.: BCTC2010001342-2E Test Standards FCC CFR 47 part1, 1.1307(b), 1.1310 Tested by: Approved by: Eric Yang/Project Handler Zero Zhou/Reviewer ReportNo.: BCTC2010001342-2E No.：BCTC/RF-EMC-005Page3of16Edition：A.1 TABLE OF CONTENT Test Report Declaration Page 1. VERSION ............................................................. 4 2. PRODUCT INFORMATION ............................................. 5 2.1 Product Information ..................................................... 5 2.2 Support Equipment ..................................................... 5 2.3 Test Mode ............................................................. 5 3. TEST FACILITY AND TEST INSTRUMENT USED ......................... 6 3.1 Test Facility ............................................................ 6 3.2 Test Instrument Used ................................................... 6 4. METHOD OF MEASUREMENT .......................................... 7 4.1 Applicable Standard .................................................... 7 4.2 Block Diagram Of Test Setup ............................................ 7 4.3 Limit .................................................................. 8 4.4 Test procedure ......................................................... 8 4.5 Equipment Approval Considerations ...................................... 9 4.6 E and H field Strength .................................................. 10 5. PHOTOGRAPHS OF TEST SET-UP ..................................... 11 (Note: N/A means not applicable) ReportNo.: BCTC2010001342-2E No.：BCTC/RF-EMC-005Page4of16Edition：A.1 1. VERSION Report No. Issue Date Description Approved BCTC2010001342-2E Nov. 03, 2020 Original Valid ReportNo.: BCTC2010001342-2E No.：BCTC/RF-EMC-005Page5of16Edition：A.1 2. PRODUCT INFORMATION 2.1 Product Information Model/Type Ref.: MSL-M2011Q SM-2826 Model differences: All the model are the same circuit and RF module, except model names. Operation Frequency: 112kHz-220kHz Antenna installation: Inductive loop coil antenna Ratings: DC 3.7V From Battery Micro-USB input: DC 5V/2A Type-C input: DC 5V/2A USB A output: DC 5V/2A Wirelss output: 5W 2.2 Support Equipment Device Type Brand Model Series No. Data Cable Remark Mobile phone iphone iphone8P N/A N/A Auxiliary Notes: 1. All the equipment/cables were placed in the worst-case configuration to maximize the emission during the test. 2. Grounding was established in accordance with the manufacturer’s requirements and conditions for the intended use. 2.3 Test Mode . Test Modes keeping TX+Charging mode ReportNo.: BCTC2010001342-2E No.：BCTC/RF-EMC-005Page6of16Edition：A.1 3. TEST FACILITY AND TEST INSTRUMENT USED 3.1 Test Facility All measurement facilities used to collect the measurement data are located at Shenzhen BCTC Testing Co., Ltd. Address: 1-2F, East of B Building, Pengzhou Industrial, Fuyuan 1st Road, Qiaotou Community, Fuyong Street, Bao’an District, Shenzhen, China. The site and apparatus are constructed in conformance with the requirements of ANSI C63.4 and CISPR 16-1-1 other equivalent standards. FCC Test Firm Registration Number: 712850 IC Registered No.: 23583 3.2 Test Instrument Used Equipment Manufacturer Model No. Serial No. Last Cal. Next Cal. Exposure Level Tester Narda ELT-400 N-0231 Jul. 15, 2020 Jul. 14, 2021 Electric and Magnetic Field Analyzer Narda EHP-200A 170WX91006 Jul. 15, 2020 Jul. 14, 2021 Magnetic field probe 100cm2 Narda B-Field Probe 100cm2 M0675 Jul. 15, 2020 Jul. 14, 2021 843 Chamber ETS 843 84301 Aug. 27, 2020 Aug. 26, 2023 ReportNo.: BCTC2010001342-2E No.：BCTC/RF-EMC-005Page7of16Edition：A.1 4. METHOD OF MEASUREMENT 4.1 Applicable Standard According to §1.1307(b)(1), systems operating under the provisions of this section shall be operated in a manner that ensures that the public is not exposed to radio frequency energy level in excess of the Commission’s guidelines. According to §1.1310 and §2.1093 RF exposure is calculated. According KDB680106 D01v03: RF Exposure Wireless Charging Apps v02. 4.2 Block Diagram Of Test Setup Note: Measurements should be made from all sides and the top of the primary/client pair, with the 15 cm measured from the center of the probe(s…

Text truncated - open the document above for the full version.

No.：BCTC/RF-EMC-005Page1of25Edition：A.1 TEST REPORT    Shenzhen BCTC Testing Co., Ltd. ReportNo.: BCTC2010001342-1E Applicant:ShenzhenMosslooIndustrialCo.,Ltd ProductName: Wirelesspowerbank Model/TypeRef.: MSL-M2011Q TestedDate: Oct.23,2020toNov.02,2020 IssuedDate: Nov.03,2020 ReportNo.: BCTC2010001342-1E No.：BCTC/RF-EMC-005Page2of25Edition：A.1 FCC ID: 2AN8F-MSLM2011Q The test report is effective only with both signature and specialized stamp.This result(s) shown in this report refer only to the sample(s) tested. Without written approval of Shenzhen BCTC Testing Co., Ltd, this report can’t be reproduced except in full.The tested sample(s) and the sample information are provided by the client. Product Name: Wireless power bank Trademark: N/A Model/Type Ref.: MSL-M2011Q SM-2826 Prepared For: Shenzhen Mossloo Industrial Co., Ltd Address: Road One No.4, Science Industrial Park, Shangxue Village, Bantian Street, Longgang District, Shenzhen China Manufacturer: Shenzhen Mossloo Industrial Co., Ltd Address: Road One No.4, Science Industrial Park, Shangxue Village, Bantian Street, Longgang District, Shenzhen China Prepared By: Shenzhen BCTC Testing Co., Ltd. Address: 1-2F, East of B Building, Pengzhou Industrial, Fuyuan 1st Road, Qiaotou Community, Fuyong Street, Bao’an District, Shenzhen, China Sample Received Date: Oct. 23, 2020 Sample tested Date: Oct. 23, 2020 to Nov. 02, 2020 Issue Date: Nov. 03, 2020 Report No.: BCTC2010001342-1E Test Standards FCC Part15.209 ANSI C63.10-2013 Tested by: Approved by: Eric Yang/Project Handler Zero Zhou/Reviewer ReportNo.: BCTC2010001342-1E No.：BCTC/RF-EMC-005Page3of25Edition：A.1 TABLE OF CONTENT Test Report Declaration Page 1. VERSION ............................................................. 4 2. TEST SUMMARY ...................................................... 5 3. MEASUREMENT UNCERTAINTY........................................ 6 4. PRODUCT INFORMATION AND TEST SETUP ............................ 7 4.1 Product Information ..................................................... 7 4.2 Test Setup Configuration ................................................ 7 4.3 Support Equipment ..................................................... 7 4.5 Test Mode ............................................................. 8 5. TEST FACILITY AND TEST INSTRUMENT USED ......................... 9 5.1 Test Facility ............................................................ 9 5.2 Test Instrument Used ................................................... 9 6. CONDUCTED EMISSIONS ............................................. 11 6.1 Block Diagram Of Test Setup ........................................... 11 6.2 Limit ................................................................. 11 6.3 Test procedure ........................................................ 11 6.4 EUT operating Conditions .............................................. 11 6.5 Test Result ........................................................... 12 7. RADIATED EMISSIONS ............................................... 14 7.1 Block Diagram Of Test Setup ........................................... 14 7.2 Limit ................................................................. 15 7.3 Test procedure ........................................................ 15 7.4 Test Result ........................................................... 17 8. BANDWIDTH TEST ................................................... 20 9. ANTENNA REQUIREMENTS ........................................... 21 10. EUT PHOTOGRAPHS ................................................. 22 11. EUT TEST SETUP PHOTOGRAPHS .................................... 23 (Note: N/A means not applicable) ReportNo.: BCTC2010001342-1E No.：BCTC/RF-EMC-005Page4of25Edition：A.1 1. VERSION Report No. Issue Date Description Approved BCTC2010001342-1E Nov. 03, 2020 Original Valid ReportNo.: BCTC2010001342-1E No.：BCTC/RF-EMC-005Page5of25Edition：A.1 2. TEST SUMMARY The Product has been tested according to the following specifications: No. Test Parameter Clause No Results 1 Conducted Emission 15.207 PASS 2 Radiated Emission 15.209 PASS 3 20dB Bandwidth 15.215 PASS 4 Antenna Requirement 15.203 PASS ReportNo.: BCTC2010001342-1E No.：BCTC/RF-EMC-005Page6of25Edition：A.1 3. MEASUREMENT UNCERTAINTY Where relevant, the following measurement uncertainty levels have been estimated for tests performed on the Product as specified in CISPR 16-4-2. This uncertainty represents an expanded uncertainty expressed at approximately the 95% confidence level using a coverage factor of k=2. No. Item Uncertainty 1 3m camber Radiated spurious emission(9kHz-30MHz) U=3.7dB 2 3m camber Radiated spurious emission(30MHz-1GHz) U=4.3dB 3 3m chamber Radiated spurious emission(1GHz-18GHz) U=4.5dB 4 Conducted Emission (150kHz-30MHz) U=3.2dB 5 humidity uncertainty U=5.3% 6 Temperature uncertainty U=0.59°C 7 Bandwidth 0.9% ReportNo.: BCTC2010001342-1E No.：BCTC/RF-EMC-005Page7of25Edition：A.1 4. PRODUCT INFORMATION AND TEST SETUP 4.1 Product Information Model/Type Ref.: MSL-M2011Q SM-2826 Model differences: All the model are the same circuit and RF module, except model names. Operation Frequency: 112kHz-220kHz Antenna installation: Inductive loop coil antenna Ratings: DC 3.7V From Battery Micro-USB input: DC 5V/2A Type-C input: DC 5V/2A USB A output: DC 5V/2A Wirelss output: 5W Test Model: MSL-M2011Q 4.2 Test Setup Configuration See test photographs attached in EUT TEST SETUP PHOTOGRAPHS for the actual connections between Product and support equipment. Conducted Emission: Radiated Spurious Emission: 4.3 Support Equipment No. Device T…

Text truncated - open the document above for the full version.

Conducted emissions Radiated Measurement Photos