2ANY6-TE300Smart Phone

材质：120克铜版纸 15.19 Labeling requirements. This device complies with part 15 of the FCC Rules. Operation is subject to the following two conditions: (1) This device may not cause harmful interference, and (2) this device must accept any interference received, including interference that may cause undesired operation. 15.21 Information to user. Any Changes or modifications not expressly approved by the party responsible for compliance could void the user's authority to operate the equipment. 15.105 Information to user. This equipment has been tested and found to comply with the limits for a Class B digital device, pursuant to Part 15 of the FCC Rules. These limits are designed to provide reasonable protection against harmful interference in a residential installation. This equipment generates uses and can radiate radio frequency energy and, if not installed and used in accordance with the instructions, may cause harmful interference to radio communications. However, there is no guarantee that interference will not occur in a particular installation. If this equipment does cause harmful interference to radio or television reception, which can be determined by turning the equipment off and on, the user is encouraged to try to correct the interference by one or more of the following measures: -- -- Increase the separation between the equipment and receiver. -- Connect the equipment into an outlet on a circuit different from that to which the receiver is connected. -- Consult the dealer or an experienced radio/TV technician for help. Specific Absorption Rate (SAR) information: This product meets the government's requirements for exposure to radio waves. The guidelines are based on standards that were developed by independent scientific organizations through periodic and thorough evaluation of scientific studies. The standards include a substantial safety margin designed to assure the safety of all persons regardless of age or health. FCC RF Exposure Information and Statement The SAR limit of USA (FCC) is 1.6 W/kg averaged over one gram of tissue. This device was tested for typical body-worn operations with the back of the handset kept 10mm from the body. To maintain compliance with FCC RF exposure requirements, use accessories that maintain a 10mm separation distance between the user's body and the back of the handset. The use of belt clips, holsters and similar accessories should not contain metallic components in its assembly. The use of accessories that do not satisfy these requirements may not comply with FCC RF exposure requirements, and should be avoided. Reorient or relocate the receiving antenna. “页面边界线”仅代表折痕及纸张大小，无需印刷出来 Telo Systems Tel:+86-755-86950766 E-mail:[email protected] Add: 6/F, No.42 Liuxian 1st Road, Bao'an District, Shenzhen, China www.telosystems.com

External photos of the EUT

Internal photos of the EUT

Page: 1 of 25 TEST REPORT Report No. .......................................: CHTEW20010111 Report verification : Project No. ..................................: SHT1911060702EW FCC ID ............................................. : 2ANY6-TE300 Applicant’s name ........................... : Telo Systems Ltd Address ............................................. : 6/F, No.42 Liuxian 1st Road, Bao'an District, Shenzhen, China Manufacturer....................................: Telo Systems Ltd Address ............................................. : 6/F, No.42 Liuxian 1st Road, Bao'an District, Shenzhen, China Test item description .................... : Smart Phone Trade Mark ....................................... : Telo Systems Model/Type reference ....................... : TE300 Listed Model(s) ................................. : - Standard ......................................... : FCC CFR Title 47 Part 15 Subpart C Section 15.225 Date of receipt of test sample..........: Dec 19, 2019 Date of testing..............................: Dec 20, 2019- Jan 11, 2020 Date of issue................................: Jan 12, 2020 Result .................. ........................: PASS Compiled by ( position+printedname+signature) ... : File administrators Silvia Li Supervised by (position+printedname+signature) .... : Project Engineer Aaron Fang Approved by (position+printedname+signature) .... : RF Manager Hans Hu Testing Laboratory Name ............. : Shenzhen Huatongwei International Inspection Co., Ltd. Address ............................................. : 1/F, Bldg 3, Hongfa Hi-tech Industrial Park, Genyu Road, Tianliao, Gongming, Shenzhen, China Shenzhen Huatongwei International Inspection Co., Ltd. All rights reserved. This publication may be reproduced in whole or in part for non-commercial purposes as long as the Shenzhen Huatongwei International Inspection Co., Ltd. is acknowledged as copyright owner and source of the material. Shenzhen Huatongwei International Inspection Co., Ltd. takes no responsibility for and will not assume liability for damages resulting from the reader's interpretation of the reproduced material due to its placement and context. The test report merely correspond to the test sample. Report No : CHTEW20010111 Page 2 of 25 Issued: 2020-01-12 Shenzhen Huatongwei International Inspection Co., Ltd. Report Template Version: V01 (2018-01) Contents 1. TEST STANDARDS AND REPORT VERSION 3 1.1. Test Standards 3 1.2. Report version information 3 2. TEST DESCRIPTION 4 3. SUMMARY 5 3.1. Client Information 5 3.2. Product Description 5 3.3. EUT operation mode 6 3.4. EUT configuration 6 4. TEST ENVIRONMENT 7 4.1. Address of the test laboratory 7 4.2. Test Facility 7 4.3. Environmental conditions 8 4.4. Statement of the measurement uncertainty 8 4.5. Equipments Used during the Test 9 5. TEST CONDITIONS AND RESULTS 11 5.1. Antenna requirement 11 5.2. AC Power Conducted Emissions 12 5.3. Field Strength of the Fundamental and Mask Measurement 15 5.4. 20dB Bandwidth 17 5.5. Radiated Emission 19 5.6. Frequency Stability 23 6. TEST SETUP PHOTOS OF THE EUT 24 7. EXTERNAL AND INTERNAL PHOTOS OF THE EUT 25 Report No : CHTEW20010111 Page 3 of 25 Issued: 2020-01-12 Shenzhen Huatongwei International Inspection Co., Ltd. Report Template Version: V01 (2018-01) 1. TEST STANDARDS AND REPORT VERSION 1.1. Test Standards The tests were performed according to following standards: FCC Rules Part 15.225: Operation within the band 13.110-14.010 MHz. ANSI C63.10-2013: American National Standard for Testing Unlicensed Wireless Devices. 1.2. Report version information Revision No. Date of issue Description N/A 2020-01-12 Original Report No : CHTEW20010111 Page 4 of 25 Issued: 2020-01-12 Shenzhen Huatongwei International Inspection Co., Ltd. Report Template Version: V01 (2018-01) 2. TEST DESCRIPTION Test Item Section in CFR 47 Result Test Engineer Antenna requirement 15.203 PASS Jiongsheng Feng AC Power Line Conducted Emissions 15.207 PASS Kang Yang Field Strength of the Fundamental and Mask Measurement 15.225(a)(b)(c) PASS Xu Yang 20dB Bandwidth 15.215 PASS Jiongsheng Feng Radiated Emission 15.225(d)&15.209 PASS Yuantao Liang Frequency Stability 15.225(e) PASS Jiongsheng Feng Report No : CHTEW20010111 Page 5 of 25 Issued: 2020-01-12 Shenzhen Huatongwei International Inspection Co., Ltd. Report Template Version: V01 (2018-01) 3. SUMMARY 3.1. Client Information Applicant: Telo Systems Ltd Address: 6/F, No.42 Liuxian 1st Road, Bao'an District, Shenzhen, China Manufacturer: Telo Systems Ltd Address: 6/F, No.42 Liuxian 1st Road, Bao'an District, Shenzhen, China 3.2. Product Description Name of EUT: Smart Phone Trade Mark: Telo Systems Model No.: TE300 Listed Model(s): - Power supply: DC 3.7V Adapter information: Model:MR-0502000US Input:100-240Va.c., 50/60Hz, 0.3A Output:5.0Vd.c., 2.0A RF Specification Operation frequency: 13.56MHz Channel number: 1 Modulation Type: ASK Antenna type: FPC antenna Antenna gain: -1.0dBi Report No : CHTEW20010111 Page 6 of 25 Issued: 2020-01-12 Shenzhen Huatongwei International Inspection Co., Ltd. Report Template Version: V01 (2018-01) 3.3. EUT operation mode TEST MODE For RF test items The engineering test program was provided and enabled to make EUT continuous transmit. For AC power line conducted emissions: The EUT was set to connect with large package sizes transmission. 3.4. EUT configuration The following peripheral devices and interface cables were connected during the measurement: ● - supplied by the manufacturer ○ - supplied by the lab Manufacturer : / Model No. : / Manufacturer : / Model No. : / Report No : CHTEW20010111 Page 7 of 25 Issued: 2020-01-12 Shenzhen Huatongwei International Inspection Co., Ltd. Report Template Version: V01 (2018-01) 4. TEST ENVIRONMENT 4.1. Address of the test laboratory Laboratory: Shenzhen Huatongwei International Inspection Co., Ltd. Address: 1/F, Bldg 3, Hongfa Hi-tech Industrial Park, Genyu Road, Tianliao, Gongming, Shenzhen, China Phone: …

Text truncated - open the document above for the full version.

Report No : CHTEW20010111 Page 24 of 25 Issued: 2020-01-12 Shenzhen Huatongwei International Inspection Co., Ltd. Report Template Version: V01 (2018-01) 6. TEST SETUP PHOTOS OF THE EUT Conducted Emissions (AC Mains) Radiated Emissions Report No : CHTEW20010111 Page 25 of 25 Issued: 2020-01-12 Shenzhen Huatongwei International Inspection Co., Ltd. Report Template Version: V01 (2018-01) 7. EXTERNAL AND INTERNAL PHOTOS OF THE EUT Reference to the test report No.: CHTEW20010102 --------End of Report--------