2AOAF-6902-in-1 magnetic charger

CQ DUAL WIRELESS CHARGER - USER GUIDE FRONT Dual Wireless Charger 2-in-1 magnetic charger FCC ID：2AOAF-690 08/02/23 / 2 3 4 0 _ C Q _ D U A L W I R E L E S S C H A R G E R _USER GUIDE_R2 / 2 CQ DUAL WIRELESS CHARGER - USER GUIDE BACK PB0531 FCC Warning This device complies with Part 15 of the FCC Rules. Operation is subject to the following two conditions: (1) This device may not cause harmful interference, and (2) this device must accept any interference received, including interference that may cause undesired operation. NOTE 1: This equipment has been tested and found to comply with the limits for a Class B digital device, pursuant to part 15 of the FCC Rules. These limits are designed to provide reasonable protection against harmful interference in a residential installation. This equipment generates, uses and can radiate radio frequency energy and, if not installed and used in accordance with the instructions, may cause harmful interference to radio communications. However, there no guarantee that interference will not occur in a particular installation. If this equipment does cause harmful interference to radio or television reception, which can be determined by turning the equipment off and on, the user is encouraged to try to correct the interference by one or more of the following measures: - Reorient or relocate the receiving antenna. - Increase the separation between the equipment and receiver. - Connect the equipment into an outlet on a circuit different from that to which the receiver is connected. - Consult the dealer or an experienced radio/TV technician for help. NOTE 2: Any changes or modifications to this unit not expressly approved by the party responsible for compliance could void the user's authority to operate the equipment. The device has been evaluated to meet general RF exposure requirement. The device can be used in portable exposure condition without restriction. 08/02/23 / 2 3 4 0 _ C Q _ D U A L W I R E L E S S C H A R G E R _USER GUIDE_R2 / 3

Tylt, inc. Address：685 Cochran St. Suite 200 Simi Valley, CA 93065 United States Date: 2023-08-07 Federal Communications Commission Authorization and Evaluation Division 1435 Oakland Mills Road Columbia, MD 21046 Ref: Attestation Statements Part 2.911(d)(7) Filing SUBJECT: FCC Application for FCC ID: 2AOAF-690 Tylt, inc. certifies that, as of the date of the filing of the application, Tylt, inc. is our designated U.S. agent for service of process for the above referenced FCC ID. Tylt, inc. accepts to maintain an agent for no less than one year after the grantee has terminated all marketing and importation or the conclusion of any Commission-related proceeding involving the equipment. Tylt, inc. accepts, as of the date of the filing of the application, the obligation of the designated U.S. agent for service of process for the above referenced FCC ID. Designated U.S. Agent Information: FRN: 0026998161 Name: Tylt, inc. Address: 685 Cochran St. Suite 200 Simi Valley, CA 93065 United States Contact Person: Andre Sumian Tel.: (800) 843-5600 2811 Email: [email protected] Sincerely, Signed on behalf of Tylt, inc. Signed on behalf of Tylt, inc. Name: Name: Title: Manager Title: Manager Date: 2023-08-07 Date: 2023-08-07

Dongguan Dexinda Electronic Technology Co.,Ltd Dongguan Hankai Electronics Co., Ltd transmit coil 44MM Client TYPE Model NO G43.5 Magnetic disc single hole double slot back adhesive line length 11MM 6.5UH DXD20221009001 101.20.04950 RAO 20221009001 Part nunbering systey Client p/NO Enginrer NO Date 2022-10-09 For Enginer Departner Only Rrvised Content APProved Date Prepared Checked Approved RAO Xie Liang Xu Yan Authorixed Signaturure Company Chop Enginrer QC APProved APProved Dongguan Dexinda Electronic Technology Co.,Ltd 一、 Winding Procese: NO winding wire gauge number of turns winding direction notes 1 N1 2UEW-B-0.07*100P 11TS CCW 2 二．FEATURES: 1.Test conditions）：25°C,65%RH@100KHz/1V 1.1 （Inductance） 1.11 L0A（Individual coil）=3.8uH±20% 1.12 1.2 1.3 1.4 L0A(Coil+magnetic disc)=6.5uH±10% q-value=65MIN DC Resistance（DCR）：55mΩ MAX (Operating Temperature)：-25°C~85°C 2.(Test instrument)：L:创达 1068+1310;DCR:502BC;SIZE:Callipers 3.Material List N O item material 1 WIRE ￠0.07*100p 2UEW-1.05mm 2 FERRITE 43.5*5.3*0.8 L-shaped slot ferrite hard magnet 3 GLUE White glue 4 SOLDER XCD-907B 5 Adhesive Slotted double-sided adhesive backing 6 High temperature adhesive 7MM High temperature tape 7 UL E238500 Dongguan Dexinda Electronic Technology Co.,Ltd 三 三．IRCUIT DIAGRAM 单位： MM 四．OUTSIDE DIAGRA Reference image Note: Wrap 7MM (ref) high-temperature adhesive tape around the coil outlet position stan dard A B C D E F H G STD 38.5±1.2 16±1.5 0.8±0.2 11±2 2-544Max 2.6Max 9-15 8 Dongguan Dexinda Electronic Technology Co.,Ltd unit： MM 五．PACKAGE 5.3 The packaging shall be based on the exusting packing plate and the actual delivery package shall prevail .If there is any requirement,we can customize it. 1400

Tylt, inc. Office of Engineering Technology Federal Communications Commission 7435 Oakland Mills Road Columbia, MD 21046 USA Date: August 7, 2023 Subject; Request for Confidentiality FCC ID: 2AOAF-690 To Whom It May Concern, Pursuant to the provisions of the Commission’s rules Title 47 Sections §0.457 and §0.459, we are requesting the Commission to withhold the following attachment(s) as confidential documents from public disclosure indefinitely. These documents contain detailed system and equipment descriptions and are considered as proprietary information in operation of the equipment. The public disclosure of these documents might be harmful to our company and would give competitors an unfair advantage in the market. Schematic Diagram Block Diagram Parts List Operational Description Tune-up Procedure Software Security Requirements for UNII devices In additional to above mentioned documents, in order to comply with the marketing regulations in Title 47 CFR §2.803 and the importation rules in Title 47 CFR §2.1204, while ensuring that business sensitive information remains confidential until the actual marketing of newly authorized devices, we request Short Term Confidentiality of the following attachment(s); External Photos Test Setup Photos Internal Photos User Manual For 45 days, pursuant to Public Notice DA 04-1705. OR For 180 days pursuant to KDB 726920 D01. It is our understanding that all measurement test reports, FCC ID label format and correspondence during the certification review process cannot be granted as confidential documents and this information will be available for public review once the grant of equipment authorization is issued. Sincerely, Signature: Name: Andre Sumian Title: Manager

Tylt, inc. Federal Communications Commission Authorization and Evaluation Division 7435 Oakland Mills Road Columbia, MD 21046 USA Date: 2023-8-3 FCC ID: 2AOAF-690 Ref. #1: Attestation Statements Part 2.911(d)(5)(i) Filing Tylt, inc. certifies that the equipment for which authorization is sought is not “covered” equipment prohibited from receiving an equipment authorization pursuant to section 2.903 of the FCC rules. Ref. #2: Attestation Statements Part 2.911(d)(5)(ii) Filing Tylt, inc. certifies that, as of the date of the filing of the application, the applicant is not identified on the Covered List as an entity producing “covered” equipment. Applicant: Tylt, inc. Address: 685 Cochran St. Suite 200 Simi Valley, CA 93065 United States Contact Person: Andre Sumian Tel.: (800) 843-5600 2811 Email: [email protected] Sincerely, Signature:

Effective Date: April 2, 2020 QSF 7.6.4-8 – Agent Authorization Letter Template Page 1 of 1 Revision Date: Revision: 0 Tylt, inc. Date：Aug. 03, 2023 Product Model Number: 2-in-1 magnetic charger FCC ID：2AOAF-690 To whom it may concern, Re: Product Certification Representative Authorization Letter We authorize QAI Laboratories Ltd. 3980 North Fraser Way, Burnaby B.C. Canada V5J 5K5 to act on our behalf on all matters concerning the above named equipment. This shall include the following:  Testing  Approval applications and procedures We declare that ORGANIZATION. is allowed to forward all information related to the approval project to the applied certification body and to the notification entities and to discuss any issues concerning the approval application. Any and all acts carried out by ORGANIZATION. on our behalf shall have the same effect as acts of our own. By: Contact Listed on FCC Wesbite Title: Manager Email: [email protected] Telephone: (800) 843-5600 2811 On behalf of: Tylt, inc.

Ext Photos Photo 1（For model QIDUET15BK-CQ） Photo 2 Photo 3 Photo 4 Photo 5 Photo 6 Photo 7 Photo 8 Photo 9

Int Photos Photo 1（For model QIDUET15BK-CQ） Photo 2 Phone: ANT Photo 3 Earphone: ANT

- Page 1 of 12 - Report No.: HB20230724002E-02 Add:Room 102, 201, Building 2, Yuanwanggu RFID Industrial Park, Tongguan Road, Tianliao Community, Yutang Street, Guangming District, Shenzhen,China Tel: (86-755) 29989321 Fax: (86-755) 29985110 Web:www.sz-hongbiao.com RF EXPOSURE Test Report Product: 2-in-1 magnetic charger Trade Mark: N/A Model Number: QIDUET15BK-CQ FCC ID: 2AOAF-690 Prepared for Tylt, inc. 685 Cochran St. Suite 200 Simi Valley, CA 93065 United States Prepared by Shenzhen HongBiao Certification& Testing Co., Ltd Room 102, 201, Building 2, Yuanwanggu RFID Industrial Park, Tongguan Road, Tianliao Community, Yutang Street, Guangming District, Shenzhen, China Tel.: +86-755-2998 9321 Fax.: +86-755-2998 5110 Website: http://www.sz-hongbiao.com - Page 2 of 12 - Report No.: HB20230724002E-02 Add:Room 102, 201, Building 2, Yuanwanggu RFID Industrial Park, Tongguan Road, Tianliao Community, Yutang Street, Guangming District, Shenzhen,China Tel: (86-755) 29989321 Fax: (86-755) 29985110 Web:www.sz-hongbiao.com Table of Contents 1 GENERAL DESCRIPTION ..................................................................................................................................... 5 1.1 DESCRIPTION OF EUT ................................................................................................................................................ 5 1.2 TEST MODE .............................................................................................................................................................. 5 1.3 TEST SETUP .............................................................................................................................................................. 5 1.4 ANCILLARY EQUIPMENT .............................................................................................................................................. 6 2 TEST FACILITIES AND ACCREDITATIONS .............................................................................................................. 7 2.1 TEST LABORATORY ..................................................................................................................................................... 7 2.2 ENVIRONMENTAL CONDITIONS ..................................................................................................................................... 7 2.3 MEASUREMENT UNCERTAINTY ..................................................................................................................................... 7 2.4 TEST SOFTWARE ........................................................................................................................................................ 7 3 LIST OF TEST EQUIPMENT .................................................................................................................................. 8 4 RF EXPOSURE..................................................................................................................................................... 9 4.1 MAXIMUM PERMISSIBLE EXPOSURE .............................................................................................................................. 9 4.1.1. Limit ............................................................................................................................................................ 9 4.1.2. Test Procedures ........................................................................................................................................... 9 4.1.3. Test Setup .................................................................................................................................................. 10 4.1.4. Test Result ................................................................................................................................................. 10 5 PHOTOGRAPHS OF THE TEST SETUP ..................................................................................................................12 - Page 3 of 12 - Report No.: HB20230724002E-02 Add:Room 102, 201, Building 2, Yuanwanggu RFID Industrial Park, Tongguan Road, Tianliao Community, Yutang Street, Guangming District, Shenzhen,China Tel: (86-755) 29989321 Fax: (86-755) 29985110 Web:www.sz-hongbiao.com TEST RESULT CERTIFICATION Applicant’s Name ................. : Tylt, inc. Address ................................. : 685 Cochran St. Suite 200 Simi Valley, CA 93065 United States Manufacturer's Name .......... : HANK ELECTRONICS VIETNAM LTD Address ................................. : No. 7,11 Street VSIP Tu Son. 16353 Bac Ninh Province. Vietnam Product description Product name ........................ : 2-in-1 magnetic charger Model Number ....................... : QIDUET15BK-CQ Standards ............................. : FCC CFR 47 PART 1 , 1.1310 Test procedure ..................... : KDB 680106 D01 RF Exposure Wireless Charging Apps v03r01 This device described above has been tested by Shenzhen HongBiao Certification& Testing Co,.Ltd and the test results show that the equipment under test (EUT) is in compliance with the EMC requirements. And it is applicable only to the tested sample identified in the report. Date of Test ........................................... : Date (s) of performance of tests ............. : July 24. 2023~July 31. 2023 Test Result .............................................. : Pass Testing Engineer : ( Z o e Su) Technical Manager : ( G a r y Lu) Authorized Signatory : (L e o S u) - Page 4 of 12 - Report No.: HB20230724002E-02 Add:Room 102, 201, Building 2, Yuanwanggu RFID Industrial Park, Tongguan Road, Tianliao Community, Yutang Street, Guangming District, Shenzhen,China Tel: (86-755) 29989321 Fax: (86-755) 29985110 Web:www.sz-hongbiao.com Revision History Revised No. Date of Issue Description 01 July 31. 2023 Original - Page 5 of 12 - Report No.: HB20230724002E-02 Add:Room 102, 201, Building 2, Yuanwanggu RFID Industrial Park, Tongguan Road, Tianliao…

Text truncated - open the document above for the full version.

- Page 1 of 30 - Report No.: HB20230724002E-01 Add:Room 102, 201, Building 2, Yuanwanggu RFID Industrial Park, Tongguan Road, Tianliao Community, Yutang Street, Guangming District, Shenzhen,China Tel: (86-755) 29989321 Fax: (86-755) 29985110 Web:www.sz-hongbiao.com Test Report Product： 2-in-1 magnetic charger Trade Mark: N/A Model Number： QIDUET15BK-CQ FCC ID： 2AOAF-690 Prepared for Tylt, inc. 685 Cochran St. Suite 200 Simi Valley, CA 93065 United States Prepared by Shenzhen HongBiao Certification& Testing Co., Ltd Room 102, 201, Building 2, Yuanwanggu RFID Industrial Park, Tongguan Road, Tianliao Community, Yutang Street, Guangming District, Shenzhen, China Tel.: +86-755-2998 9321 Fax.: +86-755-2998 5110 Website: http://www.sz-hongbiao.com - Page 2 of 30 - Report No.: HB20230724002E-01 Add:Room 102, 201, Building 2, Yuanwanggu RFID Industrial Park, Tongguan Road, Tianliao Community, Yutang Street, Guangming District, Shenzhen,China Tel: (86-755) 29989321 Fax: (86-755) 29985110 Web:www.sz-hongbiao.com Table of Contents 1 GENERAL DESCRIPTION ..................................................................................................................................... 5 1.1 DESCRIPTION OF EUT ................................................................................................................................................ 5 1.2 TEST MODE .............................................................................................................................................................. 5 1.3 TEST SETUP .............................................................................................................................................................. 6 1.4 ANCILLARY EQUIPMENT .............................................................................................................................................. 6 2 SUMMARY OF TEST RESULT ............................................................................................................................... 7 3 TEST FACILITIES AND ACCREDITATIONS .............................................................................................................. 8 3.1 TEST LABORATORY ..................................................................................................................................................... 8 3.2 ENVIRONMENTAL CONDITIONS ..................................................................................................................................... 8 3.3 MEASUREMENT UNCERTAINTY ..................................................................................................................................... 8 3.4 TEST SOFTWARE ........................................................................................................................................................ 8 4 LIST OF TEST EQUIPMENT .................................................................................................................................. 9 5 TEST ITEM AND RESULTS ...................................................................................................................................11 5.1 ANTENNA REQUIREMENT .......................................................................................................................................... 11 5.2 CONDUCTED EMISSION ............................................................................................................................................. 12 5.3 RADIATED EMISSION ................................................................................................................................................ 16 5.4 OCCUPIED BANDWIDTH ............................................................................................................................................ 21 6 PHOTOGRAPHS OF THE TEST SETUP ..................................................................................................................23 7 PHOTOGRAPHS OF THE EUT..............................................................................................................................25 - Page 3 of 30 - Report No.: HB20230724002E-01 Add:Room 102, 201, Building 2, Yuanwanggu RFID Industrial Park, Tongguan Road, Tianliao Community, Yutang Street, Guangming District, Shenzhen,China Tel: (86-755) 29989321 Fax: (86-755) 29985110 Web:www.sz-hongbiao.com TEST RESULT CERTIFICATION Applicant’s Name ................. : Tylt, inc. Address ................................. : 685 Cochran St. Suite 200 Simi Valley, CA 93065 United States Manufacturer's Name .......... : HANK ELECTRONICS VIETNAM LTD Address ................................. : No. 7,11 Street VSIP Tu Son. 16353 Bac Ninh Province. Vietnam Product description Product name ........................ : 2-in-1 magnetic charger Model Number ....................... : QIDUET15BK-CQ Standards ............................. : FCC Part 15C Test procedure ..................... : ANSI C63.4: 2014 This device described above has been tested by Shenzhen HongBiao Certification& Testing Co,.Ltd and the test results show that the equipment under test (EUT) is in compliance with the EMC requirements. And it is applicable only to the tested sample identified in the report. Date of Test ........................................... : Date (s) of performance of tests ............. : July 24. 2023~July 31. 2023 Test Result .............................................. : Pass Testing Engineer : ( Z o e Su) Technical Manager : ( G a r y Lu) Authorized Signatory : (L e o S u) - Page 4 of 30 - Report No.: HB20230724002E-01 Add:Room 102, 201, Building 2, Yuanwanggu RFID Industrial Park, Tongguan Road, Tianliao Community, Yutang Street, Guangming District, Shenzhen,China Tel: (86-755) 29989321 Fax: (86-755) 29985110 Web:www.sz-hongbiao.com Revision History Revised No. Date of Issue Description 01 July 31. 2023 Original - Page 5 of 30 - Report No.: HB20230724002E-01 Add:Room 102, 20…

Text truncated - open the document above for the full version.

- Page 1 of 2 - Test Setup Photos Radiated Emission Below 30MHz Radiated Emission Above 30MHz - Page 2 of 2 - Conducted emission MPE