2AP2N-MAG10000WMagnetic Wireless Power Bank

This equipment has been tested and found to comply with the limits for a Class B digital device, pursuant to part 15 of the FCC Rules. These limits are designed to provide reasonable protection against harmful interference in a residential installation. This equipment generates, uses and can radiate radio frequency energy and, if not installed and used in accordance with the instructions, may cause harmful interference to radio communications. However, there is no guarantee that interference will not occur in a particular installation. If this equipment does cause harmful interference to radio or television reception, which can be determined by turning the equipment off and on, the user is encouraged to try to correct the interference by one or more of the following measures: • Reorient or relocate the receiving antenna. • Increase the separation between the equipment and receiver. • Connect the equipment into an outlet on a circuit different from that to which the receiver is connected. • Consult the dealer or an experienced radio/TV technician for help. Caution: Any changes or modifications to this device not explicitly approved by manufacturer could void your authority to operate this equipment. This device complies with part 15 of the FCC Rules. Operation is subject to the following two conditions: (1) This device may not cause harmful interference, and (2) this device must accept any interference received, including interference that may cause undesired operation. The device has been evaluated to meet general RF exposure requirement.

Shenzhen Esorun Technology Co.,LTD Office of Engineering Technology Federal Communications Commission 7435 Oakland Mills Road Columbia, MD 21046 Date: 2021-05-24 Subject; Request for Long Term Confidentiality FCC ID: 2AP2N-MAG10000W To Whom It May Concern, Pursuant to the provisions of the Commission’s rules Title 47 Sections §0.457 and §0.459, we are requesting the Commission to withhold the following attachment(s) as confidential documents from public disclosure indefinitely. These documents contain detailed system and equipment descriptions and are considered as proprietary information in operation of the equipment. The public disclosure of these documents might be harmful to our company and would give competitors an unfair advantage in the market. Schematic Diagram Block Diagram Operational Description It is our understanding that all measurement test reports, FCC ID label format and correspondence during the certification review process cannot be granted as confidential documents and this information will be available for public review once the grant of equipment authorization is issued. Sincerely, Signature: Name: Zhang Yi Title: Deputy General Manager

Shenzhen Esorun Technology Co.,LTD Letter of Authorization Company: Shenzhen Esorun Technology Co.,LTD Address: 101, Dormitory Building, No. 1215, Guihua Community Guanguang Road, Guanlan Street, Longhua District, Shenzhen,China. Product Name: Magnetic Wireless Power Bank Model Number(s): Mag10000W We authorize MiCOM Labs Inc., 575 Boulder Court, Pleasanton, California 94566, USA, to act on our behalf on all matters concerning the certification of above named equipment. We declare that MiCOM Labs Inc. is allowed to forward all information related to the approval and certification of equipment to the regulatory agencies as required and to discuss any issues concerning the approval application. Any and all acts carried out by MiCOM Labs on our behalf shall have the same effect as acts of our own. Signature: Date: 2021-05-24 Name: Zhang Yi Title: Deputy General Manager Company: Shenzhen Esorun Technology Co.,LTD

FCC ID: 2AP2N-MAG10000W FCC ID: 2AP2N-MAG10000W FCC ID: 2AP2N-MAG10000W FCC ID: 2AP2N-MAG10000W

4.5cm 2.5cm Label Location FCC ID: 2AP2N-MAG10000W Shenzhen Esorun Technology Co.,LTD Product name: Magnetic Wireless Power Bank Model No.: Mag10000W This device complies with Part 15 of the FCC Rules. Operation is subject to the following two conditions: (1) this device may not cause harmful interference, and (2) this device must accept any interference received, including interference that may cause undesired operation.

FCC ID: 2AP2N-MAG10000W FCC ID: 2AP2N-MAG10000W FCC ID: 2AP2N-MAG10000W ANT FCC ID: 2AP2N-MAG10000W FCC ID: 2AP2N-MAG10000W

FCC TEST REPORT FCC ID: 2AP2N-MAG10000W On Behalf of Shenzhen Esorun Technology Co.,LTD Magnetic Wireless Power Bank Model No.: Mag10000W Prepared for : Shenzhen Esorun Technology Co.,LTD Address : 101, Dormitory Building, No. 1215, Guihua Community Guanguang Road, Guanlan Street, Longhua District, Shenzhen, China Prepared By : Shenzhen Alpha Product Testing Co., Ltd. Address : Building i, No.2, Lixin Road, Fuyong Street, Bao'an District, 518103, Shenzhen, Guangdong, China Report Number : A2101212-C01-R05 Date of Receipt : January 29, 2021 Date of Test : January 29, 2021–April 12, 2021 Date of Report : April 28, 2021 Version Number : V0 Page 2 of 31 Report No.: A2101212-C01-R05 TABLE OF CONTENTS 1. Test Result Summary .............................................................................. 5 2. General Information ................................................................................. 6 2.1. Description of Device (EUT) ............................................................................................................. 6 2.2. Accessories of Device (EUT) ........................................................................................................... 7 2.3. Tested Supporting System Details .................................................................................................. 7 2.4. Block Diagram of Connection between EUT and Simulators ....................................................... 7 2.5. Description of Test Modes ............................................................................................................... 7 2.6. Test Conditions ................................................................................................................................. 7 2.7. Test Facility ........................................................................................................................................ 8 2.8. Measurement Uncertainty ................................................................................................................ 8 2.9. Test Equipment List .......................................................................................................................... 9 3. Test Results and Measurement Data ................................................... 10 3.1. Conducted Emission ....................................................................................................................... 10 3.2. Radiated Spurious Emission Measurement ................................................................................. 13 3.3. Test Specification ............................................................................................................................ 20 4. Photos of Test Setup ............................................................................. 22 5. Photographs of EUT .............................................................................. 24 Page 3 of 31 Report No.: A2101212-C01-R05 TEST REPORT DECLARATION Applicant : Shenzhen Esorun Technology Co.,LTD Address : 101, Dormitory Building, No. 1215, Guihua Community Guanguang Road, Guanlan Street, Longhua District, Shenzhen, China Manufacturer : Shenzhen Esorun Technology Co.,LTD Address : 101, Dormitory Building, No. 1215, Guihua Community Guanguang Road, Guanlan Street, Longhua District, Shenzhen, China EUT Description : Magnetic Wireless Power Bank (A) Model No. : Mag10000W (B) Trademark : ESORUN Measurement Standard Used: FCC CFR Title 47 Part 15 Subpart C Section 15.209 The device described above is tested by Shenzhen Alpha Product Testing Co., Ltd. to determine the maximum emission levels emanating from the device and the severe levels of the device can endure and its performance criterion. The test results are contained in this test report and Shenzhen Alpha Product Testing Co., Ltd. is assumed full responsibility for the accuracy and completeness of test. Also, this report shows that the EUT is technically compliant with the FCC CFR Title 47 Part 15 Subpart C Section 15.209 requirements. This report applies to above tested sample only. This report shall not be reproduced in parts without written approval of Shenzhen Alpha Product Testing Co., Ltd. Tested by (name + signature).............: Lucas Pang Project Engineer Approved by (name + signature).......: Simple Guan Project Manager Date of issue...... .......................: April 28, 2021 Page 4 of 31 Report No.: A2101212-C01-R05 Revision History Revision Issue Date Revisions Revised By V0 April 28, 2021 Initial released Issue Lucas Pang Page 5 of 31 Report No.: A2101212-C01-R05 1. Test Result Summary Requirement CFR 47 Section Result Antenna requirement §15.203 PASS AC Power Line Conducted Emission §15.207 PASS Spurious Emission §15.209(a)(f) PASS Occupied Bandwidth §15.215 (c) PASS Note: 1. PASS: Test item meets the requirement. 2. Fail: Test item does not meet the requirement. 3. N/A: Test case does not apply to the test object. 4. The test result judgment is decided by the limit of test standard. Page 6 of 31 Report No.: A2101212-C01-R05 2. General Information 2.1. Description of Device (EUT) EUT Name : Magnetic Wireless Power Bank Model No. : Mag10000W DIFF. : N/A Trademark : ESORUN Power supply : Micro Input : 5V ⎓2A, 9V ⎓2A,12V ⎓1.5A Type-C Input: 5V⎓3A, 9V ⎓2A, 12V ⎓1.5A Type-C Output: 5V⎓2.4A, 9V ⎓2.3A, 12V ⎓1.7A USB-A Output: 5V⎓3A, 9V ⎓2A, 12V ⎓1.5A, 5V⎓4.5A(SCP) Wireless Output : 5V ⎓1A(5W), 9V ⎓0.83A(7.5W), 9V ⎓1.12A(10W), 9V ⎓1.67A(15W) Operation frequency : 112~205KHz Modulation : MSK Antenna Type : Coil Antenna, Maximum Gain is 0dBi (This value is supplied by applicant). Software version : V1.9 Hardware version : V1.1 Connector cable loss : 0.5dB (This value is supplied by applicant). Intend use environment : Residential, commercial and light industrial environment Page 7 of 31 Report No.: A2101212-C01-R05 2.2. Accessories of Device (EUT) Accessories1 : Cable Manufacturer : Shenzhen Esorun Technology Co., LTD Model : /…

Text truncated - open the document above for the full version.

MiCOM Labs Inc, 575 Boulder Court, Pleasanton, CA 94566, USA Tel: +1 (925) 462-0304, Fax: +1 (925) 462-0306, Web: www.micomlabs.com Page 1 of 2 Doc#: MC_F_731 (Rev 4.1) the wireless lab APPLICATION FOR FCC EQUIPMENT AUTHORIZATION (Form 731) Section: One Applicant’s Business Name Shenzhen Esorun Technology Co.,LTD Applicant’s FRN 0027580935 MODEL NUMBER Magnetic Wireless Power Bank Request for Grantee Code FCC ID: (Grantee + Applicant Code) 2AP2N-MAG10000W Address line 1 101, Dormitory Building, No. 1215, Guihua Community Guanguang Road Address line 2 Guanlan Street, Longhua District, Shenzhen, China City Shenzhen Zip/ Postal Code State P.O. Box Country China Phone 0086-0755-23696752 First Name Zhang Fax Middle Name Email [email protected] Last Name Yi Mail Stop Title Deputy General Manager Section: Two Instead of Applicant, the original Grant is authorized to be mailed to (All questions regarding the application will be directed to this contact. The original grant and invoice will be sent to this contact.) Technical Contact Company Name Address City Zip/ Postal Code State P.O. Box Country Phone Contact Person Fax Title Email Non - Technical Contact Company Name Address City Zip/ Postal Code State P.O. Box Country Phone Contact Person Fax Title Email Section: Three Does this application include a request for Long Term Confidentiality (LTC)? [see 47 CFR § 0.459] Yes No Does this application include a request for Short Term Confidentiality (STC)? Date? (mm/dd/yyyy) __________________________________ Yes No Is this application for Software Defined Radio (SDR) authorization? Yes No Is there a PBA associated with this Application? Please specify KDB number: _772335___________ Yes No Does the applicant request a defered Grant Date? (mm/dd/yyyy) ________________________ Yes No MiCOM Labs Inc, 575 Boulder Court, Pleasanton, CA 94566, USA Tel: +1 (925) 462-0304, Fax: +1 (925) 462-0306, Web: www.micomlabs.com Page 2 of 2 Doc#: MC_F_731 (Rev 4.1) the wireless lab Is this a Modular or Limited Modular Certification? Is there a waiver associated with this filing? No Yes Modular Type: ( if you answered “Yes“) Single Modular Approval Limited Single Modular Approval Split Modular Approval Split Limited Modular Approval Yes No Waiver Number: ______ Waiver Date: ______ Description of product as it is marketed (note: this text will appear below the equipment class on the grant) Purpose of the Application: Original equipment Change in identification of presently authorized equipment: Original FCC ID:____________________________ Original Grant Date (MM/DD/YYYY):________________________ Class II permissive change or modification of presently authorized equipment Class III permissive change to software defined radio ( Note: this may only be filed for applications pertaining to Software Defined Radio) Equipment Specifications The equipment will be operated under FCC Rule Part(s) Frequency range in MHz Rated RF power output (Watts) Frequency tolerance (%, Hz, ppm) Emission Designator (NOT for Part 15 devices) FCC Equipment Code (ex:: DTS, DSS, PCE) 0.112 0.205 15C DCD NOTE: If additional Equipment Specifications required, please use separate page Is the equipment in this application? (a) a composite device subject to an additional equipment authorization? Yes No (b) part of a system that operates with, or is marketed with, another device that requires an equipment authorization? Yes No If either of the above questions is answered “Yes” please complete the following statement (c) The related application checked above is (Check one box only) has been granted under the FCC ID listed to the right is in the process of being filed under the FCC ID listed to the right is pending with the FCC under the FCC ID listed to the right FCC ID: ____________________ MiCOM Labs Inc, 575 Boulder Court, Pleasanton, CA 94566, USA Tel: +1 (925) 462-0304, Fax: +1 (925) 462-0306, Web: www.micomlabs.com Page 3 of 2 Doc#: MC_F_731 (Rev 4.1) the wireless lab Section: Four Name of Test Firm and contact person on file with the FCC, if different from applicant or contact person Company name Shenzhen Alpha Product Testing Co., Ltd. Address Building i, No.2, Lixin Road, Fuyong Street, Bao’an District, City Shenzhen Zip Postal Code 518103 State Guangzhou P.O. Box Country China Phone +86-0755-29766001 Contact Person Mark Zhu Fax +86-0755-33942567 Email [email protected] FCC Registered Test Site Number (required for part 15 and 18 applications) 293961 FCC Designation Number CN1236 Read each certification carefully before answering and signing this application WILLFUL FALSE STATEMENTS MADE ON THIS FORM ARE PUNISHABLE BY FINE AND/OR IMPRISONMENT (U.S. CODE, TITLE 18, SECTION 1001), AND/OR REVOCATION OF ANY STATION LICENSE OR CONSTRUCTION PERMIT (U.S. CODE, TITLE 47, SECTION 312(a)(1)), AND/OR FORFEITURE (U.S. CODE, TITLE 47, SECTION 503). SECTION 5301 (ANTI-DRUG ABUSE) CERTIFICATION: The applicant must certify that neither the applicant nor any party to the application is subject to a denial of Federal benefits, that include FCC benefits, pursuant to Section 5301 of the Anti-Drug Abuse Act of 1988, 21 U.S.C. §862 because of a conviction for possession or distribution of a controlled substance. See 47 CFR 1.2002(b) for the definition of a “party” for these purposes Does the applicant or authorized agent so certify? Yes No APPLICANT/AGENT CERTIFICATION: I certify that I am authorized to sign this application. All of the statements herein and the exhibits attached hereto, are true and correct to the best of my knowledge and belief. In accepting a Grant of Equipment Authorization issued by MiCOM Labs Certification as a result of the representations made in this application, the applicant is responsible for (1) labeling the equipment with the exact FCC ID specified in this application, (2) compliance statement labeling pursuant to the applicable rules, and (3) compliance of the equipment with the applicable technical rules. If the applicant is not the actual manu…

Text truncated - open the document above for the full version.

FCC ID: 2AP2N-MAG10000W Radiated Emission FCC ID: 2AP2N-MAG10000W Conducted Emission