2APPZ-W610WPortable Wi-Fi Phone

Portable Wi-Fi Phone Quick Start Guide V1.0 W610W Packing list Handset Belt Clip Quick Start Guide Portable Wi-Fi Phone Rechargeable Battery Power Adapter Charging Base Earpiece Status Indicator Speaker Belt clamping hole Headphone jack PTT key Soft key Phone book Keypad Microphone Charging interface On-hook key/PowerOff-hook key Mute key Hands-free DSS key Screen Volume Key + Volume Key - Navigation key OK key Install the battery 1. Remove the rear case: Remove the rear case of the whole machine with a little force from the handle position A of the rear case of the main unit. 2. Install the battery: Take out the battery from the packaging box, with the battery with the notch facing up, put the battery C at the battery compartment C. 3. Install the battery cover: Align the back cover with the buckle on the back of the main unit, press your hands along the edge of the main unit from top to bottom (there will be a "click" sound during the process), and ensure that there is no gap, it means that the back cover is fastened. Replacement battery 1. Remove the rear case: Remove the rear case of the whole machine with a little force from the handle position A of the rear case of the main unit. Remove the rear case Install the battery Install the back cover CC Buckle A 2. Remove the old battery: Push up at B to remove the old battery. 3. Install the new battery: Take out the battery from the packaging box, with the battery with the notch facing up, put the battery C at the battery compartment C. Fanvil Technology Co., Ltd. Website: www.fanvil.com EMail: [email protected] [email protected] Tel: +86-755-2640-2199 Fax: +86-755-2640-2618 Add: 10/F Block A, Dualshine Global Science Innovation Center, Honglang North 2nd Road, Bao'an District, Shenzhen, China Remove the rear case Remove the battery A Install the back cover Buckle C Install the battery 4. Install the back cover: Align the back cover with the buckle on the back of the main unit, press your hands along the edge of the main unit from top to bottom (there will be a "click" sound during the process), and ensure that there is no gap, it means that the back cover is fastened. C B Connect Wi-Fi 1.Press Menu > WLAN. 2.Scan > Wi-Fi. Connect the charging base Install the belt clip Note 1.Use original factory supplied power adapter (5V/2A). A third-party power adapter may damage the handset. 2.Check the charging status on the top-right corner of the LCD screen. Configuration Configuration via Web Configuration via Phone 1.Press Menu > Advanced Settings (Default password 123). 2.Select Accounts: To configure enable the account, fill the SIP server address, port, user name, password etc. 1.Get the IP address from the phone: Press Menu > Status >Network >Wi-Fi IP. 2.Login: Input the IP address in the web browser. The PC and phone should be in the same IP address segment (The default username and password are both ‘admin’.) 3.Configure: Select Accounts, and fill the relevant content. Warning - Please dispose of lifeless battery under guidance. - Recycle your device. - Replacement of a battery with an incorrect type that can defeat a safeguard (for example,in the case of some lithium battery types). - Disposal of a battery into fire or a hot oven, or mechanically crushing or cutting of a battery, that can result in an explosion. - Leaving a battery in an extremely high temperature surrounding environment that can result in an explosion or the leakage of flammable liquid or gas. - A battery subjected to extremely low air pressure that may result in an explosion or the leakage of flammable liquid or gas. Used below 35°C in the state of charge Regulatory Compliance Federal Communication Commission (FCC) — USA This device complies with Part 15 of FCC Rules. Operation is subject to the following two conditions:(1) this device may not cause harmful interference, and (2) this device must accept any interference received; including interference that may cause undesired operation. This equipment has been tested and found to comply with the limits for a Class B digital device, pursuant to Part 15 of the FCC Rules. These limits are designed to provide reasonable protection against harmful interference in residential installation. This equipment generates, uses, and can radiate radio frequency energy, and if it is not installed and used in accordance with the instruction manual, it may cause harmful interference to radio communications. However, there is no guarantee that interference will not occur in a particular installation. If this equipment does cause harmful interference to radio or television reception, which can be determined by turning the equipment off and on, the user is encouraged to try to correct the interference by one or more of the following measures: • Reorient or relocate the receiving antenna. • Increase the separation between the equipment and receiver. • Connect the equipment into an outlet on a circuit different from that to which the receiver is connected. • Consult the dealer or an experienced radio/TV technician for help. Warning: Any changes or modifications to this unit not expressly approved by the party responsible for compliance could void the user’s authority to operate the equipment. FCC Radiation Exposure Statement: The device has been tested and comply with FCC SAR limits. And keep the device minimum 0mm from the body when normal use. This equipment complies with Part 68 of the FCC rules and the requirements adopted by the ACTA. On the bottom of this equipment is a label that contains, among other information, a product identifier in the format US: 3I1IPNANW610W. If requested, this number must be provided to the telephone company. All transmission frequencies of U-NII-1,U-NII-2A,U-NII-2C and U-NII-3 comply with 47 CFR FCC Part15.407(g) and the manufacturer declares that their transmission is maintained within the U-NII-1, U-NII-2A,U-NII-2C and U-NII-3 bands.

FanvilTechnologyCo.,LTD. 10/FBlockA,DualshineGlobalScienceInnovationHonglangNorth2ndRoad,Bao'anDistrict,Shenzhen,China FederalCommunicationsCommission AuthorizationandEvaluationDivision 7435OaklandMillsRoad Columbia,MD21046 USA Date:06-13-2023 Ref:AttestationStatementsPart2.911(d)(5)(i)Filing FCCID:2APPZ-W610W [FanvilTechnologyCo.,LTD.](“theapplicant”)certifiesthattheequipmentforwhichauthorizationis soughtisnot“covered”equipmentprohibitedfromreceivinganequipmentauthorizationpursuantto section2.903oftheFCCrules. Sincerely, (Applicantsignature) (MengjiaoHu)

FanvilTechnologyCo.,LTD. 10/FBlockA,DualshineGlobalScienceInnovationHonglangNorth2ndRoad,Bao'anDistrict,Shenzhen,China FederalCommunicationsCommission AuthorizationandEvaluationDivision 7435OaklandMillsRoad Columbia,MD21046 USA Date:06-13-2023 Ref:AttestationStatementsPart2.911(d)(5)(ii)Filing FCCID:2APPZ-W610W [FanvilTechnologyCo.,LTD.](“theapplicant”)certifiesthat,asofthedateofthefilingoftheapplication, theapplicantisnotidentifiedontheCoveredListasanentityproducing“covered”equipment. Sincerely, (Applicantsignature) (MengjiaoHu)

FanvilTechnologyCo., LTD. 10/F BlockA, DualshineGlobalScienceInnovationHonglangNorth2nd Road,Bao'anDistrict, Shenzhen, China 2.911(d)(7)USAAgentv1.2 Section2.911(d)(7)USAAgentforServiceof Process FCC ID: 2APPZ-W610W 2.911(d)(7)USADesignatedAgentforServiceof Process We, [FanvilTechnologyCo., LTD.] (“the applicant”) designate[ABP International,Inc.] NOTE1 for the purposeof acceptingserviceof processon behalfof the applicant. Applicantconsent:We Acknowledgeour consentto acceptserviceof processin the UnitedStatesfor mattersrelatedto the applicable equipment,and at the physicalU.S. addressand email addressof the designatedagent and acknowledgeour acceptanceof our obligationto maintainan agent for serviceof processin the UnitedStatesfor no less than one year after either the granteehas permanentlyterminatedall marketingand importationof the applicableequipmentwithinthe U.S., or the conclusionof any Commission-relatedadministrativeor judicial proceedinginvolvingthe equipment,whicheveris later. Agentobligation:We Acknowledgeour obligationto acceptserviceof processin the UnitedStatesfor mattersrelatedto the applicable equipmentat our physicalU.S. addressand email addressfor no less than one year after eitherthe granteehas permanentlyterminatedall marketingand importationof the applicableequipmentwithinthe U.S., or the conclusionof any Commission-relatedadministrativeor judicial proceedinginvolvingthe equipment,whicheveris later. USA Agent Companyname:ABP International,Inc. Address:13988DiplomatDr. #180 Dallas,TX 75234,UnitedStates FRN: 0023377534 ContactName:HenryCastillo TelephoneNo: (972) 831-1600140 Email:[email protected] Applicant Companyname:FanvilTechnologyCo., LTD. Address:10/F Block A, DualshineGlobalScienceInnovationHonglang North 2nd Road,Bao'anDistrict,Shenzhen,China ContactName:MengjiaoHu TelephoneNo: 86-0755-26402199 Email:[email protected] Signature:Signature: Date:Date:June 14, 2023 NOTE1: An applicantlocatedin the UnitedStatesmay designateitself as the agent for serviceof process. Reference;FederalRegisterdocument2022-28263publishedon 02/06/23 https://www.federalregister.gov/documents/2023/02/06/2022-28263/protecting-against-national-security-threats-to-the-communications-supply-c hain-through-the June 20, 2023

FCC Software Configuration Control Declaration Rev1.1 Fanvil Technology Co., LTD. 10/F Block A, Dualshine Global Science Innovation Honglang North 2nd Road, Bao'an District, Shenzhen,China FCC Software Configuration Control Declaration Date: July 3, 2023 Federal Communications Commission 7435 Oakland Mills Road Columbia, MD 21046 USA Attn: OET Dept. Product/ Model Number: Portable Wi-Fi Phone/ W610W Regarding FCC Country Code Selection guidelines identified in KDB 594280 v02r01. “All applications for equipment authorization for transmitters that can have radio parameters, or other technical parameters, reported to the Commission set by software must have an attestation indicating that no third party will have software, or configuration control, to program the device out of compliance of the technical rules under which it has been certified.” We declare that no third party will have software, or configuration control, to program the device out of compliance of the technical rules under which it has been certified. Name: Mengjiao Hu Date: 2023-07-03 Signature of applicant

Fanvil Technology Co., LTD. 10/F Block A, Dualshine Global Science Innovation Honglang North 2nd Road, Bao'an District, Shenzhen,China Agent Authorization Company: Fanvil Technology Co., LTD. Address: 10/F Block A, Dualshine Global Science Innovation Honglang North 2nd Road, Bao'an District, Shenzhen,China Product Name: Portable Wi-Fi Phone Model Number(s): W610W Product Description: Portable Wi-Fi Phone We authorize MiCOM Labs Inc., 575 Boulder Court, Pleasanton, California 94566, USA, to act on our behalf on all matters concerning the certification of above named equipment. We declare that MiCOM Labs Inc. is allowed to forward all information related to the approval and certification of equipment to the regulatory agencies as required and to discuss any issues concerning the approval application. Any and all acts carried out by MiCOM Labs on our behalf shall have the same effect as acts of our own. Signature: Date: 2023-06-26 Name: Mengjiao Hu Company: Fanvil Technology Co., LTD.

FanvilTechnologyCo.,LTD. 10/FBlockA,DualshineGlobalScienceInnovationHonglangNorth2ndRoad,Bao'anDistrict,Shenzhen,China OfficeofEngineeringTechnology FederalCommunicationsCommission 7435OaklandMillsRoad Columbia,MD21046 USA Date:2023-06-13 Subject;RequestforConfidentiality FCCID:2APPZ-W610W ToWhomItMayConcern, PursuanttotheprovisionsoftheCommission’srulesTitle47Sections§0.457and§0.459,we arerequestingtheCommissiontowithholdthefollowingattachment(s)asconfidential documentsfrompublicdisclosureindefinitely. Thesedocumentscontaindetailedsystemandequipmentdescriptionsandareconsideredas proprietaryinformationinoperationoftheequipment.Thepublicdisclosureofthesedocuments mightbeharmfultoourcompanyandwouldgivecompetitorsanunfairadvantageinthemarket. SchematicDiagram BlockDiagram PartsList OperationalDescription FCCSoftwareSecurityRequirementsforUNIIdevices Inadditionaltoabovementioneddocuments,inordertocomplywiththemarketingregulations inTitle47CFR§2.803andtheimportationrulesinTitle47CFR§2.1204,whileensuringthat businesssensitiveinformationremainsconfidentialuntiltheactualmarketingofnewly authorizeddevices,werequestShortTermConfidentialityofthefollowingattachment(s); ExternalPhotos TestSetupPhotos InternalPhotos UserManual For45days,pursuanttoPublicNoticeDA04-1705. OR For180dayspursuanttoKDB726920D01. Itisourunderstandingthatallmeasurementtestreports,FCCIDlabelformatand correspondenceduringthecertificationreviewprocesscannotbegrantedasconfidential documentsandthisinformationwillbeavailableforpublicreviewoncethegrantofequipment authorizationisissued. Sincerely FanvilTechnologyCo.,LTD. 10/FBlockA,DualshineGlobalScienceInnovationHonglangNorth2ndRoad,Bao'anDistrict,Shenzhen,China _______________________________ Contactperson:MengjiaoHu

Report No.: AGC14499230501AP03 Page 1 of 4 EXTERNAL PHOTOS All VIEW OF EUT VIEW OF ADAPTER Report No.: AGC14499230501AP03 Page 2 of 4 TOP VIEW OF EUT BOTTOM VIEW OF EUT Report No.: AGC14499230501AP03 Page 3 of 4 FRONT VIEW OF EUT BACK VIEW OF EUT Report No.: AGC14499230501AP03 Page 4 of 4 LEFT VIEW OF EUT RIGHT VIEW OF EUT ****************************************End of Report*************************************

FCC ID Label Location

Report No.: AGC14499230501AP03 Page 1 of 5 INTERNAL PHOTOS OPEN VIEW OF EUT (FIGURE 1) OPEN VIEW OF EUT (FIGURE 2) Report No.: AGC14499230501AP03 Page 2 of 5 OPEN VIEW OF EUT (FIGURE 3) VIEW-1 OF BATTERY BT/WIFI Antenna Report No.: AGC14499230501AP03 Page 3 of 5 VIEW-2 OF BATTERY INTERNAL VIEW OF EUT (FIGURE 1) Report No.: AGC14499230501AP03 Page 4 of 5 INTERNAL VIEW OF EUT (FIGURE 2) INTERNAL VIEW OF EUT (FIGURE 3) Report No.: AGC14499230501AP03 Page 5 of 5 INTERNAL VIEW OF EUT (FIGURE 4) INTERNAL VIEW OF EUT (FIGURE 5) ****************************************End of Report*************************************

CALIBRATION DATA PROBE CALIBRATION DATA DIPOLE CALIBRATION DATA

Page 1 of 77 SAR Test Report Report No.: AGC14499230501FH01 FCC ID : 2APPZ-W610W APPLICATION PURPOSE : Original Equipment PRODUCT DESIGNATION : Portable Wi-Fi Phone BRAND NAME : MODEL NAME : W610W APPLICANT : Fanvil Technology Co., Ltd. DATE OF ISSUE : Jun. 15, 2023 STANDARD(S) : IEEE Std. 1528:2013 FCC 47 CFR Part 2§2.1093 IEEE Std C95.1 ™-2005 REPORT VERSION : V1.0 Attestation of Global Compliance(Shenzhen) Co., Ltd. Report No.: AGC14499230501FH01 Page 2 of 77 Report Revise Record Report Version Revise Time Issued Date Valid Version Notes V1.0 / Jun. 15, 2023 Valid Initial Release Report No.: AGC14499230501FH01 Page 3 of 77 Test Report Applicant Name Fanvil Technology Co., Ltd. Applicant Address 10/F Block A, Dualshine Global Science Innovation, Honglang North 2nd Road, Bao'an District, Shenzhen, China Manufacturer Name Fanvil Technology Co., Ltd. Manufacturer Address 10/F Block A, Dualshine Global Science Innovation, Honglang North 2nd Road, Bao'an District, Shenzhen, China Factory Name Fanvil Technology Co., Ltd. Factory Address 10/F Block A, Dualshine Global Science Innovation, Honglang North 2nd Road, Bao'an District, Shenzhen, China Product Designation Portable Wi-Fi Phone Brand Name Model Name W610W EUT Voltage DC 3.8V by battery Applicable Standard IEEE Std. 1528:2013 FCC 47 CFR Part 2§2.1093 IEEE Std C95.1 ™-2005 Date of receipt of test item May 30, 2023 Test Date Jun. 03, 2023 to Jun. 09, 2023 Report Template AGCRT-US-5G/SAR (2021-04-20) Note: The results of testing in this report apply to the product/system which was tested only. Prepared By Jack Gui (Project Engineer) Jun. 15, 2023 Reviewed By Calvin Liu (Reviewer) Jun. 15, 2023 Approved By Max Zhang (Authorized Officer) Jun. 15, 2023 Report No.: AGC14499230501FH01 Page 4 of 77 TABLE OF CONTENTS 1. SUMMARY OF MAXIMUM SAR VALUE ......................................................................................................... 5 2. GENERAL INFORMATION ............................................................................................................................... 6 2.1. EUT DESCRIPTION......................................................................................................................................... 6 3. SAR MEASUREMENT SYSTEM ........................................................................................................................ 8 3.1. THE SATIMO SYSTEM USED FOR PERFORMING COMPLIANCE TESTS CONSISTS OF FOLLOWING ITEMS .................. 8 3.2. COMOSAR E-FIELD PROBE .......................................................................................................................... 9 3.3. ROBOT .......................................................................................................................................................... 9 3.4. VIDEO POSITIONING SYSTEM ........................................................................................................................ 10 3.5. DEVICE HOLDER .......................................................................................................................................... 10 3.6. SAM TWIN PHANTOM ................................................................................................................................... 11 4. SAR MEASUREMENT PROCEDURE .............................................................................................................. 12 4.1. SPECIFIC ABSORPTION RATE (SAR) .............................................................................................................. 12 4.2. SAR MEASUREMENT PROCEDURE ................................................................................................................ 13 4.3. RF EXPOSURE CONDITIONS ......................................................................................................................... 15 5. TISSUE SIMULATING LIQUID ......................................................................................................................... 17 5.1. THE COMPOSITION OF THE TISSUE SIMULATING LIQUID..................................................................................... 17 5.2. TISSUE DIELECTRIC PARAMETERS FOR HEAD AND BODY PHANTOMS ............................................................... 17 5.3. TISSUE CALIBRATION RESULT ....................................................................................................................... 18 6. SAR SYSTEM CHECK PROCEDURE ........................................................................................................... 20 6.1. SAR SYSTEM CHECK PROCEDURES ............................................................................................................. 20 6.2. SAR SYSTEM CHECK ................................................................................................................................... 21 7. EUT TEST POSITION ...................................................................................................................................... 23 7.1. DEFINE TWO IMAGINARY LINES ON THE HANDSET ........................................................................................... 23 7.2. CHEEK POSITION ......................................................................................................................................... 24 7.3. TILT POSITION .............................................................................................................................................. 24 7.4. BODY WORN POSITION ................................................................................................................................ 25 8. SAR EXPOSURE LIMITS ............................................................................................................................... 26 9. TEST FACILITY .............................................................................................................................................…

Text truncated - open the document above for the full version.

Page 1 of 197 FCC Test Report Report No.: AGC14499230501FE06 FCC ID : 2APPZ-W610W APPLICATION PURPOSE : Original Equipment PRODUCT DESIGNATION : Portable Wi-Fi Phone BRAND NAME : MODEL NAME : W610W APPLICANT : Fanvil Technology Co., Ltd. DATE OF ISSUE : Jun. 14, 2023 STANDARD(S) : FCC Part 15 Subpart E §15.407 REPORT VERSION : V1.0 Attestation of Global Compliance (Shenzhen) Co., Ltd Report No.: AGC14499230501FE06 Page 2 of 197 REPORT REVISE RECORD Report Version Revise Time Issued Date Valid Version Notes V1.0 / Jun. 14, 2023 Valid Initial Release Report No.: AGC14499230501FE06 Page 3 of 197 TABLE OF CONTENTS 1. VERIFICATION OF CONFORMITY .................................................................................................................. 5 2. GENERAL INFORMATION .............................................................................................................................. 6 2.1. PRODUCT DESCRIPTION ........................................................................................................................ 6 2.2. TABLE OF CARRIER FREQUENCYS....................................................................................................... 7 2.3. RELATED SUBMITTAL(S) / GRANT (S) ................................................................................................. 10 2.4. TEST METHODOLOGY ........................................................................................................................... 10 2.5. SPECIAL ACCESSORIES ....................................................................................................................... 10 2.6. EQUIPMENT MODIFICATIONS .............................................................................................................. 10 2.7. ANTENNA REQUIREMENT .................................................................................................................... 10 3. TEST ENVIRONMENT ................................................................................................................................... 11 3.1 ADDRESS OF THE TEST LABORATORY ............................................................................................... 11 3.2 TEST FACILITY ......................................................................................................................................... 11 3.3 ENVIRONMENTAL CONDITIONS ............................................................................................................ 12 3.4 MEASUREMENT UNCERTAINTY ............................................................................................................ 12 3.5 LIST OF EQUIPMENTS USED ................................................................................................................. 13 4. DESCRIPTION OF TEST MODES ................................................................................................................. 14 5. SYSTEM TEST CONFIGURATION ................................................................................................................ 15 5.1. CONFIGURATION OF EUT SYSTEM ..................................................................................................... 15 5.2. EQUIPMENT USED IN EUT SYSTEM .................................................................................................... 15 5.3. SUMMARY OF TEST RESULTS ............................................................................................................. 15 6. RF OUTPUT POWER MEASUREMENT........................................................................................................ 16 6.1 MEASUREMENT LIMITS ......................................................................................................................... 16 6.2 MEASUREMENT PROCEDURE .............................................................................................................. 16 6.3 MEASUREMENT SETUP (BLOCK DIAGRAM OF CONFIGURATION) .................................................. 17 6.4 MEASUREMENT RESULT ....................................................................................................................... 17 7. 6DB&26DB BANDWIDTH MEASUREMENT ................................................................................................ 21 7.1 MEASUREMENT LIMITS ......................................................................................................................... 21 7.2 MEASUREMENT PROCEDURE .............................................................................................................. 21 7.3 MEASUREMENT SETUP (BLOCK DIAGRAM OF CONFIGURATION) .................................................. 21 7.4 MEASUREMENT RESULTS ..................................................................................................................... 22 8. POWER SPECTRAL DENSITY MEASUREMENT ........................................................................................ 63 8.1 MEASUREMENT LIMITS ......................................................................................................................... 63 8.2 MEASUREMENT PROCEDURE .............................................................................................................. 63 8.3 MEASUREMENT SETUP (BLOCK DIAGRAM OF CONFIGURATION) .................................................. 63 8.4 MEASUREMENT RESULT ....................................................................................................................... 64 9. CONDUCTED SPURIOUS EMISSION........................................................................................................... 98 Report No.: AGC14499230501FE06 Page 4 of 197 9.1 MEASUREMENT LIMIT ............................................................................................................................ 98 9.2 MEASUREMENT PROCEDURE ..................................................................................................…

Text truncated - open the document above for the full version.

Report No.: AGC14499230501FE06 Page 76 of 197 Test_Graph_802.11a_ANT1_5320_6Mbps_PSD Test_Graph_802.11n20_ANT1_5260_MCS0_PSD Report No.: AGC14499230501FE06 Page 77 of 197 Test_Graph_802.11n20_ANT1_5300_MCS0_PSD Test_Graph_802.11n20_ANT1_5320_MCS0_PSD Report No.: AGC14499230501FE06 Page 78 of 197 Test_Graph_802.11n40_ANT1_5270_MCS0_PSD Test_Graph_802.11n40_ANT1_5310_MCS0_PSD Report No.: AGC14499230501FE06 Page 79 of 197 Test_Graph_802.11ac20_ANT1_5260_MCS0_PSD Test_Graph_802.11ac20_ANT1_5300_MCS0_PSD Report No.: AGC14499230501FE06 Page 80 of 197 Test_Graph_802.11ac20_ANT1_5320_MCS9_PSD Test_Graph_802.11ac40_ANT1_5270_MCS9_PSD Report No.: AGC14499230501FE06 Page 81 of 197 Test_Graph_802.11ac40_ANT1_5310_MCS9_PSD Test_Graph_802.11ac80_ANT1_5290_MCS9_PSD Report No.: AGC14499230501FE06 Page 82 of 197 Test Graphs of Conducted Output Power Spectral Density for band 5.47-5.725 GHz Test_Graph_802.11a_ANT1_5500_6Mbps_PSD Test_Graph_802.11a_ANT1_5600_6Mbps_PSD Report No.: AGC14499230501FE06 Page 83 of 197 Test_Graph_802.11a_ANT1_5700_6Mbps_PSD Test_Graph_802.11n20_ANT1_5500_MCS0_PSD Report No.: AGC14499230501FE06 Page 84 of 197 Test_Graph_802.11n20_ANT1_5600_MCS0_PSD Test_Graph_802.11n20_ANT1_5700_MCS0_PSD Report No.: AGC14499230501FE06 Page 85 of 197 Test_Graph_802.11n40_ANT1_5510_MCS0_PSD Test_Graph_802.11n40_ANT1_5590_MCS0_PSD Report No.: AGC14499230501FE06 Page 86 of 197 Test_Graph_802.11n40_ANT1_5670_MCS0_PSD Test_Graph_802.11ac20_ANT1_5500_MCS0_PSD Report No.: AGC14499230501FE06 Page 87 of 197 Test_Graph_802.11ac20_ANT1_5600_MCS0_PSD Test_Graph_802.11ac20_ANT1_5700_MCS9_PSD Report No.: AGC14499230501FE06 Page 88 of 197 Test_Graph_802.11ac40_ANT1_5510_MCS9_PSD Test_Graph_802.11ac40_ANT1_5590_MCS9_PSD Report No.: AGC14499230501FE06 Page 89 of 197 Test_Graph_802.11ac40_ANT1_5670_MCS9_PSD Test_Graph_802.11ac80_ANT1_5530_MCS9_PSD Report No.: AGC14499230501FE06 Page 90 of 197 Test_Graph_802.11ac80_ANT1_5610_MCS9_PSD Report No.: AGC14499230501FE06 Page 91 of 197 Test Graphs of Conducted Output Power Spectral Density for band 5.725-5.85 GHz Test_Graph_802.11a_ANT1_5745_6Mbps_PSD Test_Graph_802.11a_ANT1_5785_6Mbps_PSD Report No.: AGC14499230501FE06 Page 92 of 197 Test_Graph_802.11a_ANT1_5825_6Mbps_PSD Test_Graph_802.11n20_ANT1_5745_MCS0_PSD Report No.: AGC14499230501FE06 Page 93 of 197 Test_Graph_802.11n20_ANT1_5785_MCS0_PSD Test_Graph_802.11n20_ANT1_5825_MCS0_PSD Report No.: AGC14499230501FE06 Page 94 of 197 Test_Graph_802.11n40_ANT1_5755_MCS0_PSD Test_Graph_802.11n40_ANT1_5795_MCS0_PSD Report No.: AGC14499230501FE06 Page 95 of 197 Test_Graph_802.11ac20_ANT1_5745_MCS0_PSD Test_Graph_802.11ac20_ANT1_5785_MCS0_PSD Report No.: AGC14499230501FE06 Page 96 of 197 Test_Graph_802.11ac20_ANT1_5825_MCS9_PSD Test_Graph_802.11ac40_ANT1_5755_MCS9_PSD Report No.: AGC14499230501FE06 Page 97 of 197 Test_Graph_802.11ac40_ANT1_5795_MCS9_PSD Test_Graph_802.11ac80_ANT1_5775_MCS9_PSD Report No.: AGC14499230501FE06 Page 98 of 197 9. CONDUCTED SPURIOUS EMISSION 9.1 MEASUREMENT LIMIT Restricted bands Applicable to Limit 789033 D02 General UNII Test Procedures New Rules v02r01 Field strength at 3m (dBuV/m) PK: 74 AV: 54 Out of the restricted bands Applicable to EIRP Limit (dBm/MHz) Equivalent field Strength at 3m (dBuV/m) FCC 15.407(b)(1) PK: -27 PK: 68.2 15.407(b)(2) 15.407(b)(3) 15.407(b)(4) See Note 2 Note 1: The following formula is used to convert the equipment isotropic radiated power (eirp) to field strength: Note 2: All emissions shall be limited to a level of -27 dBm/MHz at 75 MHz or more above or below the band edge increasing linearly to 10 dBm/MHz at 25 MHz above or below the band edge, and from 25 MHz above or below the band edge increasing linearly to a level of 15.6 dBm/MHz at 5 MHz above or below the band edge, and f…

Text truncated - open the document above for the full version.