2APTF-W1Relectric skateboard

Exway Wave Hub/Riot User Manual Top Speed： Hill Climbing： Range： Weight： Torque： Max. Power: Rated Motor Power： Max Amperage： Input Voltage： Battery Capacity： Charging Time： Trucks： Brakes： Recommended Age Range： Max Load： Waterproof Level： 23mph / 38kph Up to 25% Grade 15miles / 24km Riot 7.3kg / Hub 6.9kg Riot 4.3Nm×2 / Hub 3.8Nm×2 1000W×2 430W×2 4A 100-240VAC,50 / 60Hz 216Wh 3.5 hours (1h30mins with the fast charger) Exway Trist 45° 7” Regenerative Braking 16-50 Years 100kg / 220lbs IP53 （Actual data varies depending on rider weight and riding conditions.） RiotHub 01 1 4 9 13 11 12 10 5 6 7 8 2 3 1 Front of the Board 2 Grip Tape 3 Kicktail 4 Truck 5 Charging Port 6 Battery 7 Status Indicator/Power Button 8 Taillight 9 Front light Auxiliary Port 10 Motor Controller (ESC) 11 Brushless Motors 12 Rear Drive Wheel 13 Tail Puck 02 Battery Swap: Install the front lights Battery Installation: Align both the ports from the battery and deck. Slide the battery into place，ensuring that it's securely mounted. (Otherwise, it may fall out while riding and cause danger or injury) The battery is also equipped with a USB port with 5V-2.1A to charge your devices like remote/ cell phone. ① Press and Hold Down the Battery Release Button ②Slide Battery Forward to Install ② Slide Battery Backward to Remove Battery Removal: Press and hold down the battery release button, meanwhile slide the battery towards the rear truck to lift it away from the board. Install the lights on the front of the board and ensure that the four screws are fully tightened. Turn on the board and then double tap the multi-button on the remote to switch on the lights. CAUTION: 1. When the skateboard battery has 5% left, the power output will be cut off to better protect the battery. (In free mode, both the power output and brakes will be restricted) 2. Connect the charger to the power button on the board before plugging into the wall outlet. (Only use an original Exway Wave charger) BY THE WAY： 1. The board will charge for around 3.5h with the standard charger. The indicator on the charger will turn green when the battery is full. 2. This version of the user manual may not be updated, check out the Exway App or www.exwayboard.com to read the most up-to-date version. Operations & The state of the indicator lights: 03 Show the Remaining Battery Single tap while the board is powered off. Power On Long press for 2 seconds. Power Off Long press for 3 seconds while the board is turned on. Pairing Mode Long press for 8 seconds while the board is powered off. Brick Recovery/ Firmware Upgrade Mode Fast tap 7 times while the board is powered off. Charging Light flashes continuously. 8s ScreenOLED 0.9”: : 2.4GHzWireless Frequency :5V 1AInput Voltage Remote Control Operation: Accelerate/Break Roll the throttle wheel forward/back. Switch Off (Standby Mode) Press the Multi-Button for 3 seconds. Switch Gears Short press the Multi-Button. Change Direction Triple-tap the Multi-Button. Turn on/off the Headlight Double-tap the Multi-Button. Acceleration (roll the throttle forward) Throttle Wheel Breaking (roll the throttle back) Multi-Button OLED screen 14 18 17 16 15 04 14 15 16 1718 Remote Control Calibration Push the roller forward to the bottom without letting go, press multi-button to Confirm. Choose the first option “Re-Pair” by tapping on the Multi- Button. Choose your board and click “YES”. Calibrate the neutral position, release the roller to make it free, press multi-button to confirm. Press multi-button to confirm when calibration is completed and the calibration interface is automatically exited. 05 Pairing Remote to Board: Pairing Mode Completely turn off the board and long press 8 sec on the board to turn on pair mode. Setting Mode Long press the Multi-Button on the remote for 5 seconds to get into setting mode. WARNINGS ESC HIGH TEMPERATURE WARNING ESC OVERHEATING WARNING ESC temperature is over 120°C. (Stop using your board immediately to allow it to cool) ESC OVERHEAT ESC OVERHEAT LOW TEMPERATURE Temperature is below 0°C (Caution frost). LOW TEMPERATURE BATTERY TEMPERATURE WARNING Battery temperature is over 55°C BATTERY(55°) MOTOR HIGH TEMPERATURE WARNING Motor temperature is over 100°C. MOTOR OVERHEATING WARNING Motor temperature is over 120°C. (Stop using your board immediately allow it to cool) MOTOR BREAKDOWN Motor Seizing HIGH VOLTAGE（I） Voltage is too high HIGH VOLTAGE（II） Voltage is too high (Danger risk ! Discharge it Before use) MOTOR OVERHEAT MOTOR OVERHEAT MOTOR BREAKDOWN HIGH VOLTAGE() HIGH VOLTAGE( ) 06 LOW TEMPERATURE Low Charge temperature BATTERY OVERHEAT Battery is overheating while charging. REMOTE DISCONNECTED Remote is not connected to board. LOW TEMPERATURE DISCONNECTED BMS ERROR BMS error or connection issue at battery communication port. BATTERY OVERHEAT BMS ERROR 07 In the box： ⑤⑥ ① ⑦ ④②③ ④ Remote Charging Cable ② Remote ③ Standard charger ① Exway Wave ⑥ User Manual ⑤ Skate Tool ⑦ 2.0 mm L Wrench 2.5 mm L Wrench 5.0mm L Wrench 1. Whenever you ride an Exway board, you risk death or serious injury from loss of control, collisions, and falls. To ride safely, you must read and follow all warnings and instructions in this manual. 2. Always wear a helmet when riding. Never ride in water, wet surfaces, in the rain, slippery or uneven surfaces, steep hills, traffic, cracks, train tracks, gravel, rocks, or any obstacles that could cause a loss of traction. Avoid night riding, areas with poor visibility, and narrow spaces. 3. Do not ride an Exway board in environments, on inclines, or at speeds where you would not be safely in control of an unpowered skateboard. In the event of wireless interference or battery fault, you may need to rely on skating techniques like foot-braking or sliding to stop. The Exway electric skateboard is not a toy and is not intended for Children under 16. 4. Please ride responsibly and respect those around you. How you ride will determine how people view this new mode of transportation. 5. The ver…

Text truncated - open the document above for the full version.

SUNTO TECHNOLOGY CO., LTD Office of Engineering Technology Federal Communications Commission 7435 Oakland Mills Road Columbia, MD 21046 USA Date: 2020/10/19 Subject; Request for Confidentiality FCC ID: 2APTF-W1R To Whom It May Concern, Pursuant to the provisions of the Commission’s rules Title 47 Sections §0.457 and §0.459, we are requesting the Commission to withhold the following attachment(s) as confidential documents from public disclosure indefinitely. These documents contain detailed system and equipment descriptions and are considered as proprietary information in operation of the equipment. The public disclosure of these documents might be harmful to our company and would give competitors an unfair advantage in the market. Schematic Diagram Block Diagram Operational Description In additional to above mentioned documents, in order to comply with the marketing regulations in Title 47 CFR §2.803 and the importation rules in Title 47 CFR §2.1204, while ensuring that business sensitive information remains confidential until the actual marketing of newly authorized devices, we request Short Term Confidentiality of the following attachment(s); User Manual For 45 days, pursuant to Public Notice DA 04-1705. OR For 180 days pursuantto KDB 726920 D01. It is our understanding that all measurement test reports, FCC ID label format and correspondence during the certification review process cannot be granted as confidential documents and this information will be available for public review once the grant of equipment authorization is issued. Sincerely, Signature: Name: He Huiming Title: Manager

SUNTO TECHNOLOGY CO., LTD Model Difference Product Name: electric skateboard Model Number(s): W1R， W1H Trademark: N/A All the model are the same circuit and RF module, except model names. Regards Sincerely Client’s signature: Client’s name / title : He Huiming /Manager Contact information / address: Room A3-09-11; No.108; Lijia Road; Henggang Street; Longgang District; Shenzhen, China

External Photos

Size:30*15mm FCC ID: 2APTF-W1R This device complies with Part 15 of the FCC Rules. Operation is subject to the following two conditions:(1)This device may not cause harmful interference, and (2) this device must accept any interference received, including interference that may cause und esired operation. Label location

Internal Photos SRD Antenna BT Antenna

Shenzhen BCTC Testing Co., Ltd. FCC ID: 2APTF-W1R Portable device According to §15.247(e)(i) and §1.1307(b)(1), systems operating under the provisions of this section shall be operated in a manner that ensures that the public is not exposed to radio frequency energy level in excess of the Commission’s guidelines. According to KDB447498 D01 General RF Exposure Guidance V06 The 1-g SAR and 10-g SAR test exclusion thresholds for 100 MHz to 6 GHz at test separation distances ≤ 50 mm are determined by: [(max. power of channel, including tune-up tolerance, mW)/(min. test separation distance, mm)]·[√f(GHZ)] ≤ 3.0 for 1-g SAR and ≤ 7.5 for 10-g extremity SAR, where: • f(GHZ) is the RF channel transmit frequency in GHz • Power and distance are rounded to the nearest mW and mm before calculation • The result is rounded to one decimal place for comparison When the minimum test separation distance is < 5 mm, a distance of 5 mm is applied to determine SAR test exclusion. Modulation Channel Freq. (GHz) Conduct ed power (dBm) Conducte d power (mW) Tune-up power (dBm) Max tune-up power (dBm) Max tune-up power (mW) Distance (mm) Result calculatio n SAR Exclusion threshold SAR test exclusion BT-GFSK2.4025.053.206±17.005.01<51.553523.00YES SRD-GFSK2.4051.501.411±12.001.58<50.491573.00YES Conclusion: For the max result : 1.55352≤3.0, the SAR testing is not required.

No.：BCTC/RF-EMC-005Page:1of43Edition：A.1 TEST REPORT  ReportNo.:BCTC2008003059-1E Applicant:SUNTOTECHNOLOGYCO.,LTD ProductName:electricskateboard Model/TypeRef.: W1R TestedDate:Sep.02,2020toSep.28,2020 IssuedDate:Sep.29,2020    Shenzhen BCTC Testing Co., Ltd. ReportNo.: BCTC2008003059-1E No.：BCTC/RF-EMC-005Page:2of43Edition：A.1 FCC ID: 2APTF-W1R Tested by: Approved by: Eric Yang/Project Handler Zero Zhou/Reviewed The test report is effective only with both signature and specialized stamp.This result(s) shown in this report refer only to the sample(s) tested. Without written approval of Shenzhen BCTC Testing Co., Ltd, this report can’t be reproduced except in full.The tested sample(s) and the sample information are provided by the client. Product Name: electric skateboard Trademark: N/A Model/Type Ref.: W1R W1H Prepared For: SUNTO TECHNOLOGY CO., LTD Address: Room A3-09-11; No.108; Lijia Road; Henggang Street; Longgang District; Shenzhen, China Manufacturer: SUNTO TECHNOLOGY CO., LTD Address: Room A3-09-11; No.108; Lijia Road; Henggang Street; Longgang District; Shenzhen, China Prepared By: Shenzhen BCTC Testing Co., Ltd. Address: 1-2F, East of B Building, Pengzhou Industrial, Fuyuan 1st Road, Qiaotou Community, Fuyong Street, Bao’an District, Shenzhen, China Sample Received Date: Sep. 02, 2020 Sample tested Date: Sep. 02, 2020 to Sep. 28, 2020 Issue Date: Sep. 29, 2020 Report No.: BCTC2008003059-1E Test Standards FCC Part15.247 ANSI C63.10-2013 Test Results PASS Remark: This is Bluetooth BLE radio test report. ReportNo.: BCTC2008003059-1E No.：BCTC/RF-EMC-005Page:3of43Edition：A.1 TABLE OF CONTENT Test Report Declaration Page 1. VERSION ............................................................. 5 2. TEST SUMMARY ...................................................... 6 3. MEASUREMENT UNCERTAINTY........................................ 7 4. PRODUCT INFORMATION AND TEST SETUP ............................ 8 4.1 Product Information ..................................................... 8 4.2 Test Setup Configuration ................................................ 8 4.3 Support Equipment ..................................................... 9 4.4 Channel List ........................................................... 9 4.5 Test Mode ............................................................. 9 4.6 Table of parameters of text software setting ............................... 10 5. TEST FACILITY AND TEST INSTRUMENT USED ........................ 11 5.1 Test Facility ........................................................... 11 5.2 Test Instrument Used .................................................. 11 6. CONDUCTED EMISSIONS ............................................. 13 6.1 Block Diagram Of Test Setup ........................................... 13 6.2 Limit ................................................................. 13 6.3 Test procedure ........................................................ 13 6.4 EUT operating Conditions .............................................. 13 6.5 Test Result ........................................................... 14 7. RADIATED EMISSIONS ............................................... 16 7.1 Block Diagram Of Test Setup ........................................... 16 7.2 Limit ................................................................. 17 7.3 Test procedure ........................................................ 18 7.4 EUT operating Conditions .............................................. 19 7.5 Test Result ........................................................... 20 8. RADIATED BAND EMISSION MEASUREMENT AND RESTRICTED BANDS OF OPERATION .......................................................... 24 8.1 Block Diagram Of Test Setup ........................................... 24 8.2 Limit ................................................................. 24 8.3 Test procedure ........................................................ 25 8.4 EUT operating Conditions .............................................. 25 8.5 Test Result ........................................................... 26 9. POWER SPECTRAL DENSITY TEST ................................... 27 9.1 Block Diagram Of Test Setup ........................................... 27 9.2 Limit ................................................................. 27 9.3 Test procedure ........................................................ 27 9.4 EUT operating Conditions .............................................. 27 9.5 Test Result ........................................................... 28 10. BANDWIDTH TEST ................................................... 30 10.1 Block Diagram Of Test Setup .......................................... 30 10.2 Limit ................................................................ 30 ReportNo.: BCTC2008003059-1E No.：BCTC/RF-EMC-005Page:4of43Edition：A.1 10.3 Test procedure ....................................................... 30 10.4 EUT operating Conditions ............................................. 30 10.5 Test Result .......................................................... 31 11. PEAK OUTPUT POWER TEST ......................................... 33 11.1 Block Diagram Of Test Setup .......................................... 33 11.2 Limit ................................................................ 33 11.3 Test procedure ....................................................... 33 11.4 EUT operating Conditions ............................................. 33 11.5 Test Result .......................................................... 34 12. 100 KHZ BANDWIDTH OF FREQUENCY BAND EDGE ................... 35 12.1 Block Diagram Of Test Setup .......................................... 35 12.2 Limit .............…

Text truncated - open the document above for the full version.

 No.：BCTC/RF-EMC-005Page:1of43Edition：A.1 TEST REPORT   ReportNo.:BCTC2008003059-2E Applicant:SUNTOTECHNOLOGYCO.,LTD ProductName:electricskateboard Model/TypeRef.: W1R TestedDate:Sep.02,2020toSep.28,2020 IssuedDate:Sep.29,2020    Shenzhen BCTC Testing Co., Ltd. ReportNo.: BCTC2008003059-2E No.：BCTC/RF-EMC-005Page:2of43Edition：A.1 FCC ID: 2APTF-W1R Tested by: Approved by: Eric Yang/Project Handler Zero Zhou/Reviewed The test report is effective only with both signature and specialized stamp.This result(s) shown in this report refer only to the sample(s) tested. Without written approval of Shenzhen BCTC Testing Co., Ltd, this report can’t be reproduced except in full.The tested sample(s) and the sample information are provided by the client. Product Name: electric skateboard Trademark: N/A Model/Type Ref.: W1R W1H Prepared For: SUNTO TECHNOLOGY CO., LTD Address: Room A3-09-11; No.108; Lijia Road; Henggang Street; Longgang District; Shenzhen, China Manufacturer: SUNTO TECHNOLOGY CO., LTD Address: Room A3-09-11; No.108; Lijia Road; Henggang Street; Longgang District; Shenzhen, China Prepared By: Shenzhen BCTC Testing Co., Ltd. Address: 1-2F, East of B Building, Pengzhou Industrial, Fuyuan 1st Road, Qiaotou Community, Fuyong Street, Bao’an District, Shenzhen, China Sample Received Date: Sep. 02, 2020 Sample tested Date: Sep. 02, 2020 to Sep. 28, 2020 Issue Date: Sep. 29, 2020 Report No.: BCTC2008003059-2E Test Standards FCC Part15.247 ANSI C63.10-2013 Test Results PASS ReportNo.: BCTC2008003059-2E No.：BCTC/RF-EMC-005Page:3of43Edition：A.1 TABLE OF CONTENT Test Report Declaration Page 1. VERSION ............................................................. 5 2. TEST SUMMARY ...................................................... 6 3. MEASUREMENT UNCERTAINTY........................................ 7 4. PRODUCT INFORMATION AND TEST SETUP ............................ 8 4.1 Product Information ..................................................... 8 4.2 Test Setup Configuration ................................................ 8 4.3 Support Equipment ..................................................... 9 4.4 Channel List ........................................................... 9 4.5 Test Mode ............................................................. 9 5. TEST FACILITY AND TEST INSTRUMENT USED ........................ 10 5.1 Test Facility ........................................................... 10 5.2 Test Instrument Used .................................................. 11 6. CONDUCTED EMISSIONS ............................................. 13 6.1 Block Diagram Of Test Setup ........................................... 13 6.2 Limit ................................................................. 13 6.3 Test procedure ........................................................ 13 6.4 EUT operating Conditions .............................................. 13 6.5 Test Result ........................................................... 14 7. RADIATED EMISSIONS ............................................... 16 7.1 Block Diagram Of Test Setup ........................................... 16 7.2 Limit ................................................................. 17 7.3 Test procedure ........................................................ 18 7.4 EUT operating Conditions .............................................. 19 7.5 Test Result ........................................................... 20 8. RADIATED BAND EMISSION MEASUREMENT AND RESTRICTED BANDS OF OPERATION .......................................................... 24 8.1 Block Diagram Of Test Setup ........................................... 24 8.2 Limit ................................................................. 24 8.3 Test procedure ........................................................ 25 8.4 EUT operating Conditions .............................................. 25 8.5 Test Result ........................................................... 26 9. POWER SPECTRAL DENSITY TEST ................................... 27 9.1 Block Diagram Of Test Setup ........................................... 27 9.2 Limit ................................................................. 27 9.3 Test procedure ........................................................ 27 9.4 EUT operating Conditions .............................................. 27 9.5 Test Result ........................................................... 28 10. BANDWIDTH TEST ................................................... 30 10.1 Block Diagram Of Test Setup .......................................... 30 10.2 Limit ................................................................ 30 10.3 Test procedure ....................................................... 30 ReportNo.: BCTC2008003059-2E No.：BCTC/RF-EMC-005Page:4of43Edition：A.1 10.4 EUT operating Conditions ............................................. 30 10.5 Test Result .......................................................... 31 11. PEAK OUTPUT POWER TEST ......................................... 33 11.1 Block Diagram Of Test Setup .......................................... 33 11.2 Limit ................................................................ 33 11.3 Test procedure ....................................................... 33 11.4 EUT operating Conditions ............................................. 33 11.5 Test Result .......................................................... 34 12. 100 KHZ BANDWIDTH OF FREQUENCY BAND EDGE ................... 35 12.1 Block Diagram Of Test Setup .......................................... 35 12.2 Limit ................................................................ 35 12.3 Test procedure ......................................................…

Text truncated - open the document above for the full version.

Conducted emissions Radiated Measurement Photos