2APW4EPIC3Tablet PC

Quick Start GuideGuía de Inicio RápidoGuia de Início Rápido FCC Caution: Any Changes or modifications not expressly approved by the party responsible for compliance could void the user's authority to operate the equipment. This device complies with part 15 of the FCC Rules. Operation is subject to the following two conditions: (1) This device may not cause harmful interference, and (2) this device must accept any interference received, including interference that may cause undesired operation. Note: This equipment has been tested and found to comply with the limits for a Class B digital device, pursuant to part 15 of the FCC Rules. These limits are designed to provide reasonable protection against harmful interference in a residential installation. This equipment generates, uses and can radiate radio frequency energy and, if not installed and used in accordance with the instructions, may cause harmful interference to radio communications. However, there is no guarantee that interference will not occur in a particular installation. If this equipment does cause harmful interference to radio or television reception, which can be determined by turning the equipment off and on, the user is encouraged to try to correct the interference by one or more of the following measures: • Reorient or relocate the receiving antenna. • Increase the separation between the equipment and receiver. • Connect the equipment into an outlet on a circuit different from that to which the receiver is connected. • Consult the dealer or an experienced radio/TV technician for help. Precaución de FCC:Cualquier cambio o modificación no aprobada expresamente por la parte responsable del cumplimiento podría anular la autoridad del usuario para operar el equipo. Este dispositivo cumple con la parte 15 de las Reglas de la FCC. El funcionamiento está sujeto a las dos condiciones siguientes: (1) este dispositivo no puede causar interferencias perjudiciales y (2) este dispositivo debeaceptar cualquier interferencia recibida, incluidas aquellasque puedan causar un funcionamiento no deseado.Nota: Este equipo ha sido probado y cumple con los límites para un dispositivo digital de Clase B, de conformidad con la parte 15 de las Reglas de la FCC. Estos límites están diseñados para proporcionar una protección razonable contra interferencias perjudiciales en una instalación residencial. Este equipo genera, utiliza y puede irradiar energía de radiofrecuencia y, si no se instala y utiliza de acuerdo con las instrucciones, puede causar interferencias perjudiciales en las comunicaciones de radio. Sin embargo, no hay garantía de que no se produzcan interferencias en una instalación en particular. Si este equipo causa interferencias perjudiciales en la recepción de radio o televisión, lo que se puede determinar apagando y encendiendo el equipo, se recomienda al usuario que intente corregir la interferencia mediante una o más de las siguientes medidas:• Reorientar o reubicar la antena receptora.• Aumente la separación entre el equipo y el receptor.• Conecte el equipo a una toma de corriente en un circuito diferente al que está conectado el receptor.• Consulte al distribuidor o a un técnico experimentado de radio / TV para obtener ayuda. FCC Radiation Exposure Statement: This equipment complies with FCC radiation exposure limits set forth for an uncontrolled environment. Déclaration d'exposition aux rayonnements de la FCC:Cet équipement est conforme aux limites d'exposition aux rayonnements de la FCC établies pour un environnement non contrôlé. PT Front camera / Cámara frontal Camera / Cámara Memory card tray / Slot de la tarjeta de memoria Jack port / Puerto jack USB Port (Type-C) / Puerto USB (tipo C) Volume key / Tecla Volumen Power key / Tecla Encendido Quick Start GuideGuía de Inicio RápidoGuia de Início Rápido FCC Caution: Any Changes or modifications not expressly approved by the party responsible for compliance could void the user's authority to operate the equipment. This device complies with part 15 of the FCC Rules. Operation is subject to the following two conditions: (1) This device may not cause harmful interference, and (2) this device must accept any interference received, including interference that may cause undesired operation. Note: This equipment has been tested and found to comply with the limits for a Class B digital device, pursuant to part 15 of the FCC Rules. These limits are designed to provide reasonable protection against harmful interference in a residential installation. This equipment generates, uses and can radiate radio frequency energy and, if not installed and used in accordance with the instructions, may cause harmful interference to radio communications. However, there is no guarantee that interference will not occur in a particular installation. If this equipment does cause harmful interference to radio or television reception, which can be determined by turning the equipment off and on, the user is encouraged to try to correct the interference by one or more of the following measures: • Reorient or relocate the receiving antenna. • Increase the separation between the equipment and receiver. • Connect the equipment into an outlet on a circuit different from that to which the receiver is connected. • Consult the dealer or an experienced radio/TV technician for help. Precaución de FCC:Cualquier cambio o modificación no aprobada expresamente por la parte responsable del cumplimiento podría anular la autoridad del usuario para operar el equipo. Este dispositivo cumple con la parte 15 de las Reglas de la FCC. El funcionamiento está sujeto a las dos condiciones siguientes: (1) este dispositivo no puede causar interferencias perjudiciales y (2) este dispositivo debeaceptar cualquier interferencia recibida, incluidas aquellasque puedan causar un funcionamiento no deseado.Nota: Este equipo ha sido probado y cumple con los límites para un dispositivo digital de Clase B, de conformidad con la parte 15 de las Reglas …

Text truncated - open the document above for the full version.

Bolt Modus Corp Oficina N.33 Edificio Ofidepositos Central, Calidonia - Distrito Federal, Panama Tel: 13056144478-5323 Email: [email protected] Date: 2022-06-10 FEDERAL COMMUNICATIONS COMMISSIONS Authorization and Evaluation Division 7435 Oakland Mills Road Columbia, MD 21046 Dear Sir/Madam, The RF chip, model: XR829 installed in our product Tablet PC, model: EPIC, FCC ID: 2APW4EPIC3, supports BT,BLE,2.4G Wi-Fi &5G Wi-Fi function, but for marketing purpose, this chip only supports BT,BLE and 2.4G Wi-Fi function, the 5G Wi-Fi function was disabled to use by manufacture in the software, the end user has no capability to activate it. Sincerely Yours, Signature: Giovanna Briceno Homologation leader

BoltModusCorp OficinaN.33EdificioOfidepositosCentral,Calidonia-DistritoFederal,Panama Tel:13056144478-5323 Email:[email protected] FCCConfidentialAuthorization Date:2022-06-09 FEDERALCOMMUNICATIONSCOMMISSIONS AuthorizationandEvaluationDivision 7435OaklandMillsRoad Columbia,MD21046 Subject:ConfidentialityRequestregardingapplicationforcertificationof FCCID:2APW4EPIC3 InaccordancewithSections0.457and0.459oftheCommission’sRules, BoltModusCorpherebyrequestslong-termconfidentialtreatmentofinformation accompanyingthisapplicationasoutlinedbelow: BlockDiagram Schematics OperationDescription Theabovematerialscontainproprietaryandconfidentialinformationnotcustomarily releasedtothepublic.Thepublicdisclosureofthesematerialsprovidesunjustified benefitstoitscompetitorsinthemarket. SincerelyYours, Signature: GiovannaBriceno Homologationleader

BoltModusCorp OficinaN.33EdificioOfidepositosCentral,Calidonia-DistritoFederal,Panama Tel:13056144478-5323 Email:[email protected] QA-FR-170-B7/29/2014 FCCAuthorization Date:2022-06-10 FEDERALCOMMUNICATIONSCOMMISSIONS AuthorizationandEvaluationDivision 7435OaklandMillsRoad Columbia,MD21046 Subject:AgentAuthorization Towhomitmayconcern: WeBoltModusCorp,theundersigned,herebyauthorizesShenzhenAccurate TechnologyCo.,Ltd.toactonitsbehalfinallmattersrelatingtoapplicationfor Equipmentauthorization,includingthesigningofalldocumentsrelatingtothese matters.AllactscarriedoutbyShenzhenAccurateTechnologyCo.,Ltd.onourbehalf shallhavethesameeffectasourownaction. We,theundersigned,herebycertifythatwearenotsubjecttoadenialoffederal benefits,thatincludesFCCbenefits,pursuanttoSection5301oftheAnti-DrugAbuse Actof1988,21U.S.C.862. Thisauthorizationisvaliduntilfurtherwrittennoticefromtheapplicant. SincerelyYours, Signature: GiovannaBriceno Homologationleader

Shenzhen Accurate Technology Co., Ltd. Project No.: SZNS220428-17186E-RF External Photos Page 1 of 5 External Photos Shenzhen Accurate Technology Co., Ltd. Project No.: SZNS220428-17186E-RF External Photos Page 2 of 5 Shenzhen Accurate Technology Co., Ltd. Project No.: SZNS220428-17186E-RF External Photos Page 3 of 5 Shenzhen Accurate Technology Co., Ltd. Project No.: SZNS220428-17186E-RF External Photos Page 4 of 5 Shenzhen Accurate Technology Co., Ltd. Project No.: SZNS220428-17186E-RF External Photos Page 5 of 5

Shenzhen Accurate Technology Co., Ltd. Project No.: SZNS220428-17186E-RF LABEL AND LOCATION Page 1 of 1 FCC ID Label FCC ID Label Location Information The label shown shall be permanently affixed at a conspicuous location on the device and be readily visible to the user at the time purchase (Labeling requirements per 2.925)

Shenzhen Accurate Technology Co., Ltd. Project No.: SZNS220428-17186E-RF Internal Photos Page 1 of 9 Internal photos Shenzhen Accurate Technology Co., Ltd. Project No.: SZNS220428-17186E-RF Internal Photos Page 2 of 9 Shenzhen Accurate Technology Co., Ltd. Project No.: SZNS220428-17186E-RF Internal Photos Page 3 of 9 Shenzhen Accurate Technology Co., Ltd. Project No.: SZNS220428-17186E-RF Internal Photos Page 4 of 9 Shenzhen Accurate Technology Co., Ltd. Project No.: SZNS220428-17186E-RF Internal Photos Page 5 of 9 Shenzhen Accurate Technology Co., Ltd. Project No.: SZNS220428-17186E-RF Internal Photos Page 6 of 9 Shenzhen Accurate Technology Co., Ltd. Project No.: SZNS220428-17186E-RF Internal Photos Page 7 of 9 Shenzhen Accurate Technology Co., Ltd. Project No.: SZNS220428-17186E-RF Internal Photos Page 8 of 9 Antenna Shenzhen Accurate Technology Co., Ltd. Project No.: SZNS220428-17186E-RF Internal Photos Page 9 of 9

Note: This report may contain data that are not covered by the A2LA accreditation and are marked with an asterisk “★”. Shenzhen Accurate Technology Co., Ltd. is not responsible for the authenticity of any test data provided by the applicant. Data included from the applicant that may affect test results are marked with an asterisk ’*’. Customer model name, addresses, names, trademarks etc. are not considered data. This report cannot be reproduced except in full, without prior written approval of the Company. Unless otherwise stated the results shown in this test report refer only to the sample(s) tested. This report is valid only with a valid digital signature. The digital signature may be available only under the Adobe software above version 7.0. Shenzhen Accurate Technology Co., Ltd. 1/F., Building A, Changyuan New Material Port, Science & Industry Park, Nanshan District, Shenzhen, Guangdong, P.R. China Tel: +86 755-26503290 Fax: +86 755-26503396 Web: www.atc-lab.com Version 801: 2021-11-09 Page 1 of 36 FCC SAR TEST REPORT Applicant Name : Bolt Modus Corp Address : Oficina N.33 Edificio Ofidepositos Central, Calidonia - Distrito Federal, Panama Report Number : SZNS220428-17186E-SA FCC ID: 2APW4EPIC3 Test Standard (s) FCC Part 2.1093 Sample Description Product Type: Tablet PC Model No.: EPIC 3 Multiple Model(s) No.: N/A Trade Mark: yezz Date Received: 2022/04/30 Test Date: 2022/07/09 Report Date: 2022/07/11 Test Result: Pass* * In the configuration tested, the EUT complied with the standards above. Prepared and Checked By: Approved By: Lance Li Candy Li EMC Engineer EMC Engineer Shenzhen Accurate Technology Co., Ltd. Report No.: SZNS220428-17186E-SA Version 801: 2021-11-09 Page 2 of 36 FCC SAR Attestation of Test Results MODE Max. SAR Level(s) Reported(W/kg) Limit (W/kg) WLAN 2.4G 1g Body SAR 0.18 1.6 BT 1g Body SAR 0.20 Applicable Standards FCC 47 CFR part 2.1093 Radiofrequency radiation exposure evaluation: portable devices RF Exposure Procedures: TCB Workshop April 2019 IEEE1528:2013 IEEE Recommended Practice for Determining the Peak Spatial-Average Specific Absorption Rate (SAR) in the Human Head from Wireless Communications Devices: Measurement Techniques IEC 62209-1:2016 Measurement procedure for the assessment of specific absorption rate of human exposure to radio frequency fields from hand-held and body-mounted wireless communication devices – Part 1: Devices used next to the ear (Frequency range of 300 MHz to 6 GHz) KDB procedures KDB 447498 D01 General RF Exposure Guidance v06 KDB 447498 D04 Interim General RF Exposure Guidance v01 KDB 865664 D01 SAR Measurement 100 MHz to 6 GHz v01r04 KDB 865664 D02 RF Exposure Reporting v01r02 KDB 941225 D07 UMPC Mini Tablet v01r02 KDB 248227 D01 802 11 Wi-Fi SAR v02r02 Note: This wireless device has been shown to be capable of compliance for localized specific absorption rate (SAR) for General Population/Uncontrolled Exposure limits specified in FCC 47 CFR part 2.1093 and has been tested in accordance with the measurement procedures specified in IEEE 1528-2013 and RF exposure KDB procedures. The results and statements contained in this report pertain only to the device(s) evaluated. Shenzhen Accurate Technology Co., Ltd. Report No.: SZNS220428-17186E-SA Version 801: 2021-11-09 Page 3 of 36 FCC SAR TABLE OF CONTENTS DOCUMENT REVISION HISTORY ......................................................................................................................... 4 EUT DESCRIPTION ................................................................................................................................................... 5 TECHNICAL SPECIFICATION ............................................................................................................................................. 5 REFERENCE, STANDARDS, AND GUIDELINES ................................................................................................. 6 SAR LIMITS ..................................................................................................................................................................... 7 FACILITIES ................................................................................................................................................................. 8 DESCRIPTION OF TEST SYSTEM .......................................................................................................................... 9 EQUIPMENT LIST AND CALIBRATION ............................................................................................................. 15 EQUIPMENTS LIST & CALIBRATION INFORMATION ........................................................................................................ 15 SAR MEASUREMENT SYSTEM VERIFICATION ............................................................................................. 16 LIQUID VERIFICATION ................................................................................................................................................... 16 SYSTEM ACCURACY VERIFICATION ............................................................................................................................... 17 SAR SYSTEM VALIDATION DATA ......................................................................................................................... 18 EUT TEST STRATEGY AND METHODOLOGY ................................................................................................. 19 TEST POSITIONS FOR BODY-WORN AND OTHER CONFIGURATIONS .................................................................................. 19 TEST DISTANCE FOR SAR EVALUATION ........................................................................................................................ 19 SAR EVALUATION PROCEDURE .................................................................................................................................... 20 CONDUCTED OUTPUT POWER MEASUREMENT .............…

Text truncated - open the document above for the full version.

Note: This report may contain data that are not covered by the A2LA accredit ★ ation and are marked with an asterisk “ ”. Shenzhen Accurate Technology Co., Ltd. is not responsible for the authenticity of any test data provided by the applicant. Data included from the applicant that may affect test results are marked with an asterisk ’*’. Customer model name, addresses, names, trademarks etc. are not considered data. This report cannot be reproduced except in full, without prior written approval of the Company. Unless otherwise stated the results shown in this test report refer only to the sample(s) tested. This report is valid only with a valid digital signature. The digital signature may be available only under the Adobe software above version 7.0. Shenzhen Accurate Technology Co., Ltd. 1/F., Building A, Changyuan New Material Port, Science & Industry Park, Nanshan District, Shenzhen, Guangdong, P.R. China Tel: +86 755-26503290 Fax: +86 755-26503396 Web: www.atc-lab.com Version 12: 2021-11-09 Page 1 of 61 FCC- BLE&2.4G Wi-Fi TEST REPORT Applicant Name : Bolt Modus Corp Address : Oficina N.33 Edificio Ofidepositos Central, Calidonia - Distrito Federal, Panama Report Number : SZNS220428-17186E-RF-00B FCC ID: 2APW4EPIC3 Test Standard (s) FCC PART 15.247 Sample Description Product Type: Tablet PC Model No.: EPIC 3 Multiple Model(s) No.: N/A Trade Mark: yezz Date Received: 2022/04/28 Report Date: 2022/07/04 Test Result: Pass* * In the configuration tested, the EUT complied with the standards above. Prepared and Checked By: Approved By: Andy Yu Robert Li EMC Engineer EMC Engineer Shenzhen Accurate Technology Co., Ltd. Report No.: SZNS220428-17186E-RF-00B Version 12: 2021-11-09 Page 2 of 61 FCC- BLE&2.4G Wi-Fi TABLE OF CONTENTS GENERAL INFORMATION ....................................................................................................................................... 4 PRODUCT DESCRIPTION FOR EQUIPMENT UNDER TEST (EUT) ..................................................................................... 4 OBJECTIVE ................................................................................................................................................................... 4 TEST METHODOLOGY .................................................................................................................................................. 4 MEASUREMENT UNCERTAINTY .................................................................................................................................... 5 SYSTEM TEST CONFIGURATION .......................................................................................................................... 6 DESCRIPTION OF TEST CONFIGURATION ...................................................................................................................... 6 EQUIPMENT MODIFICATIONS ....................................................................................................................................... 7 EUT EXERCISE SOFTWARE .......................................................................................................................................... 7 DUTY CYCLE ................................................................................................................................................................ 7 SUMMARY OF TEST RESULTS ............................................................................................................................. 12 TEST EQUIPMENT LIST ......................................................................................................................................... 13 FCC§15.247 (I), §1.1307 (B) (3) &§2.1093 – RF EXPOSURE ..................................................................................... 15 APPLICABLE STANDARD ............................................................................................................................................ 15 FCC §15.203 - ANTENNA REQUIREMENT ........................................................................................................... 16 APPLICABLE STANDARD ............................................................................................................................................ 16 ANTENNA CONNECTOR CONSTRUCTION .................................................................................................................... 16 FCC §15.207 (A) – AC LINE CONDUCTED EMISSIONS .................................................................................... 17 APPLICABLE STANDARD ............................................................................................................................................ 17 EUT SETUP ................................................................................................................................................................ 17 EMI TEST RECEIVER SETUP ....................................................................................................................................... 17 TEST PROCEDURE ...................................................................................................................................................... 17 TRANSD FACTOR & MARGIN CALCULATION.............................................................................................................. 18 TEST DATA ................................................................................................................................................................ 18 FCC §15.209, §15.205 & §15.247(D) - SPURIOUS EMISSIONS ............................................................................ 21 APPLICABLE STANDARD ............................................................................................................................................ 21 EUT SETUP ................................................................................................................................…

Text truncated - open the document above for the full version.

Shenzhen Accurate Technology Co., Ltd. Project No.: SZNS220428-17186E-RF Test Photos Page 1 of 2 Photo of Conducted Emission Measurement Shenzhen Accurate Technology Co., Ltd. Project No.: SZNS220428-17186E-RF Test Photos Page 2 of 2 Photo of Radiated Emission Measurement (Below 1G) Photo of Radiated Emission Measurement (Above 1G)