2APX7K57Smart Phone

FCC Cautio n: Any Chang es or modifications not expressly approved by the party responsible for compliance could void the user's authority to operate the equipment. This device complies with part 15 of the FCC Rules. Operation is subject to the following two conditions: (1) This device may not cause harmful interference, and (2) this device must accept any interference received, including interference that may cause undesired operation. IMP ORTANT NOTE: Note: This equipment has been tested and found to comply with the limits for a Class B digital device, pursuant to part 15 of the FCC Rules. These limits are designed to provide reasonable protection against harmful interference in a residential installation. This equipment generates, uses and can radiate radio frequency energy and, if not installed and used in accordance with the instructions, may cause harmful interference to radio communications. However, there is no guarantee that interference will not occur in a particular installation. If this equipment does cause harmful interference to radio or television reception, which can be determined by turning the equipment off and on, the user is encouraged to try to correct the interference by one or more of the following measures: —Re orient or relocate the receiving antenna. —Increa se the separation between the equipment and receiver. —Co nnect the equipment into an outlet on a circuit different from that to which the receiver is connected. —Co nsult the dealer or an experienced radio/TV technician for help. S pecific Absorption Rate (SAR) information SAR test s are conducted using standard operating positions accepted by the FCC with the PHONE transmitting at its highest certified power level in all tested frequency bands, although the SAR is determined at the highest certified power level, the actual SAR level of the PHONE while operating can be well below the maximum value. Before a new model PHONE is a available for sale to the public, it must be tested and certified to the FCC that it does not exceed the exposure limit established by the FCC, tests for each PHONE are performed in positions and locations as required by the FCC. For body worn operation, this model PHONE has been tested and meets the FCC RF exposure guidelines when used with an accessory designated for this product or when used with an accessory that contains no metal and that positions the handset a minimum of 10mm from the body. Non-compliance with the above restrictions may result in violation of RF exposure guidelines —Increa se the separation between the equipment and receiver. —Co nnect the equipment into an outlet on a circuit different from that to which the receiver is connected. —Co nsult the dealer or an experienced radio/TV technician for help. S pecific Absorption Rate (SAR) information SAR test s are conducted using standard operating positions accepted by the FCC with the PHONE transmitting at its highest certified power level in all tested frequency bands, although the SAR is determined at the highest certified power level, the actual SAR level of the PHONE while operating can be well below the maximum value. Before a new model PHONE is a available for sale to the public, it must be tested and certified to the FCC that it does not exceed the exposure limit established by the FCC, tests for each PHONE are performed in positions and locations as required by the FCC. For body worn operation, this model PHONE has been tested and meets the FCC RF exposure guidelines when used with an accessory designated for this product or when used with an accessory that contains no metal and that positions the handset a minimum of 10mm from the body. Non-compliance with the above restrictions may result in violation of RF exposure guidelines —Increase the separation between the equipment and receiver. —Connect the equipment into an outlet on a circuit different from that to which the receiver is connected. —Consult the dealer or an experienced radio/TV technician for help. Specific Absorption Rate (SAR) information SAR tests are conducted using standard operating positions accepted by the FCC with the phone transmitting at its highest certified. Power level in all tested frequency bands, although the SAR is determined at the highest certified power level, the actual SAR level of the phone while operating Before a new model phone is a available for sale to the public, it must be tested and certified to the FCC that it does not exceed the exposure limit established by For body worn operation, this model phone has been tested and meets the FCC RF exposure guidelines when used with an accessory designated for this product Non-compliance with the above restrictions may result in violation of RF exposure guidelines. can be well below the maximum value. by the FCC, tests for each phone are performed in positions and locations as required by the FCC. or when used with an accessory that contains no metal and that positions the handset a minimum of 10mm from the body.

KRIPTO MOBILE CORPORATION 7236 NW 31ST ST., MIAMI Florida United States Tel: +1 305 499 3333 Fax: +1 786 693 8098 Email: [email protected] Date: 2020-05-29 FEDERAL COMMUNICATIONS COMMISSIONS Authorization and Evaluation Division 7435 Oakland Mills Road Columbia, MD 21046 Dear Sir/Madam, The Main chip, model: SC9832E, installed in our product Smart phone, model: K57, FCC ID: 2APX7K57, this chip supports WCDMA and LTE function, but for marketing purpose, this chip only supports WCDMA band 2/5 and LTE band 2/4/7. The other LTE/WCDMA bands was disabled to use by manufacture in the software, the end user has no capability to activate it. Signature: RENATO TAVARES SOFTWARE MANAGER

KRIPTO MOBILE CORPORATION 7236 NW 31ST ST., MIAMI Florida United States Tel: +1 305 499 3333 Fax: +1 786 693 8098 Email: [email protected] QA-FR-170-B 7/29/2014 FCC Authorization Date: 2020-05-29 FEDERAL COMMUNICATIONS COMMISSIONS Authorization and Evaluation Division 7435 Oakland Mills Road Columbia, MD 21046 Subject: Agent Authorization To whom it may concern: We KRIPTO MOBILE CORPORATION, the undersigned, hereby authorizes Bay Area Compliance Laboratories Corporation to act on its behalf in all matters relating to application for Equipment authorization, including the signing of all documents relating to these matters. All acts carried out by Bay Area Compliance Laboratories Corporation on our behalf shall have the same effect as our own action. We, the undersigned, hereby certify that we are not subject to a denial of federal benefits, that includes FCC benefits, pursuant to Section 5301 of the Anti-Drug Abuse Act of 1988, 21 U.S.C. 862. This authorization is valid until further written notice from the applicant. Sincerely Yours, Signature: RENATO TAVARES SOFTWARE MANAGER

KRIPTO MOBILE CORPORATION 7236 NW 31ST ST., MIAMI Florida United States Tel: +1 305 499 3333 Fax: +1 786 693 8098 Email: [email protected] FCC Confidential Authorization Date: 2020-05-29 FEDERAL COMMUNICATIONS COMMISSIONS Authorization and Evaluation Division 7435 Oakland Mills Road Columbia, MD 21046 Subject: Confidentiality Request regarding application for certification of FCC ID: 2APX7K57 In accordance with Sections 0.457 and 0.459 of the Commission’s Rules, KRIPTO MOBILE CORPORATION hereby requests long-term confidential treatment of information accompanying this application as outlined below: • Block Diagram • Schematics • Operation Description • Parts List/Tune up procedure (for licensed devices) The above materials contain proprietary and confidential information not customarily released to the public. The public disclosure of these materials provides unjustified benefits to its competitors in the market. Sincerely Yours, Signature: RENATO TAVARES SOFTWARE MANAGER

EXHIBIT B - EUT EXTERNAL PHOTOGRAPHS Adapter:

EXHIBIT A - FCC ID LABEL AND LOCATION FCC ID Label FCC ID Label Location Information The label shown shall be permanently affixed at a conspicuous location on the device and be readily visible to the user at the time purchase (Labeling requirements per 2.925)

EXHIBIT C - EUT INTERNAL PHOTOGRAPHS GMS/WCDMA/LTE Main Antenna Battery Aux Antenna Bluetooth/Wi-Fi Antenna

Note: This report must not be used by the customer to claim product certification, approval, or endorsement by A2LA* or any agency of the Federal Government. This report may contain data that are not covered by the A2LA accreditation and are marked with an asterisk “★”. BACL is not responsible for the authenticity of any test data provided by the applicant. Data included from the applicant that may affect test results are marked with an asterisk ’*’. Customer model name, addresses, names, trademarks etc. are not considered data. This report cannot be reproduced except in full, without prior written approval of the Company. Unless otherwise stated the results shown in this test report refer only to the sample(s) tested. This report is valid only with a valid digital signature. The digital signature may be available only under the Adobe software above version 7.0. SAR EVALUATION REPORT For KRIPTO MOBILE CORPORATION 7236 NW 31ST ST., MIAMI Florida United States FCC ID: 2APX7K57 R e p o r t T y p e : O r i gi n a l R e p o r t P r o d u c t T y p e : S ma r t p h o n e Report Number: RSZ200519004-SA Report Date: 2020-06-02 Reviewed By: Alvin Huang Lab Manager Prepared By: Bay Area Compliance Laboratories Corp. (Shenzhen) 6/F., West Wing, Third Phase of Wanli Industrial Building, Shihua Road, Futian Free Trade Zone, Shenzhen, Guangdong, China Tel: +86-755-33320018 Fax: +86-755-33320008 www.baclcorp.com.cn Bay Area Compliance Laboratories Corp. (Shenzhen) Report No.: RSZ200519004-SA SAR Evaluation Report 2 of 64 Attestation of Test Results EUT Information EUT Description Smart phone Tested Model K57 FCC ID 2APX7K57 Serial Number RSZ200519004-SA-S1 Test Date 2020/05/23 to 2020/05/25 MODE Max. SAR Level(s) Reported(W/kg) Limit (W/kg) GSM 850 1g Head SAR 0.27 1. 6 1g Body SAR 0.25 PCS 1900 1g Head SAR 0.21 1g Body SAR 0.43 WCDMA Band 2 1g Head SAR 0.46 1g Body SAR 0.72 WCDMA Band 5 1g Head SAR 0.11 1g Body SAR 0.34 LTE Band 2 1g Head SAR 0.47 1g Body SAR 0.95 LTE Band 4 1g Head SAR 0.44 1g Body SAR 0.66 LTE Band 7 1g Head SAR 0.32 1g Body SAR 0.76 Simultaneous 1g Head SAR 0.84 1g Body SAR 1.14 1g Body SAR 1.14 (Hotspot) Bay Area Compliance Laboratories Corp. (Shenzhen) Report No.: RSZ200519004-SA SAR Evaluation Report 3 of 64 Applicable Standards FCC 47 CFR part 2.1093 Radiofrequency radiation exposure evaluation: portable devices IEEE1528:2013 IEEE Recommended Practice for Determining the Peak Spatial-Average Specific Absorption Rate (SAR) in the Human Head from Wireless Communications Devices: Measurement Techniques IEC 62209-2:2010 Human exposure to radio frequency fields from hand-held and body-mounted wireless communication devices-Human models, instrumentation, and procedures-Part 2: Procedure to determine the specific absorption rate (SAR) for wireless communication devices used in close proximity to the human body (frequency range of 30 MHz to 6 GHz) IEC 62209-1:2016 Measurement procedure for the assessment of specific absorption rate of human exposure to radio frequency fields from hand-held and body-mounted wireless communication devices – Part 1: Devices used next to the ear (Frequency range of 300 MHz to 6 GHz) KDB procedures KDB 447498 D01 General RF Exposure Guidance v06 KDB 648474 D04 Handset SAR v01r03 KDB 865664 D01 SAR Measurement 100 MHz to 6 GHz v01r04 KDB 865664 D02 RF Exposure Reporting v01r02 KDB 941225 D01 3G SAR Procedures v03r01 KDB 941225 D05 SAR for LTE Devices v02r05 KDB 941225 D06 Hotspot Mode v02r01 KDB 248227 D01 802.11 Wi-Fi SAR v02r02 Note: This wireless device has been shown to be capable of compliance for localized specific absorption rate (SAR) for General Population/Uncontrolled Exposure limits specified in FCC 47 CFR part 2.1093 and has been tested in accordance with the measurement procedures specified in IEEE 1528-2013 and RF exposure KDB procedures. The results and statements contained in this report pertain only to the device(s) evaluated. Bay Area Compliance Laboratories Corp. (Shenzhen) Report No.: RSZ200519004-SA SAR Evaluation Report 4 of 64 TABLE OF CONTENTS DOCUMENT REVISION HISTORY ......................................................................................................................... 5 EUT DESCRIPTION ................................................................................................................................................... 6 TECHNICAL SPECIFICATION ......................................................................................................................................... 6 REFERENCE, STANDARDS, AND GUIDELINES ................................................................................................. 7 SAR LIMITS ................................................................................................................................................................ 8 FACILITIES ................................................................................................................................................................. 9 DESCRIPTION OF TEST SYSTEM ........................................................................................................................ 10 EQUIPMENT LIST AND CALIBRATION ............................................................................................................. 15 EQUIPMENTS LIST & CALIBRATION INFORMATION ................................................................................................... 15 SAR MEASUREMENT SYSTEM VERIFICATION ............................................................................................. 16 LIQUID VERIFICATION ............................................................................................................................................... 16 SYSTEM ACCURACY VERIFICATION .......................................................................................................................... 18 SAR SYSTEM VALIDATION DATA ........................................…

Text truncated - open the document above for the full version.

Bay Area Compliance Laboratories Corp. (Shenzhen) Report No.: RSZ200519004- SA Page 1 of 35 APPENDIX B CALIBRATION CERTIFICATES Bay Area Compliance Laboratories Corp. (Shenzhen) Report No.: RSZ200519004- SA Page 2 of 35 Bay Area Compliance Laboratories Corp. (Shenzhen) Report No.: RSZ200519004- SA Page 3 of 35 Bay Area Compliance Laboratories Corp. (Shenzhen) Report No.: RSZ200519004- SA Page 4 of 35 Bay Area Compliance Laboratories Corp. (Shenzhen) Report No.: RSZ200519004- SA Page 5 of 35 Bay Area Compliance Laboratories Corp. (Shenzhen) Report No.: RSZ200519004- SA Page 6 of 35 Bay Area Compliance Laboratories Corp. (Shenzhen) Report No.: RSZ200519004- SA Page 7 of 35 Bay Area Compliance Laboratories Corp. (Shenzhen) Report No.: RSZ200519004- SA Page 8 of 35 Bay Area Compliance Laboratories Corp. (Shenzhen) Report No.: RSZ200519004- SA Page 9 of 35 Bay Area Compliance Laboratories Corp. (Shenzhen) Report No.: RSZ200519004- SA Page 10 of 35 Bay Area Compliance Laboratories Corp. (Shenzhen) Report No.: RSZ200519004- SA Page 11 of 35 Bay Area Compliance Laboratories Corp. (Shenzhen) Report No.: RSZ200519004- SA Page 12 of 35 Bay Area Compliance Laboratories Corp. (Shenzhen) Report No.: RSZ200519004- SA Page 13 of 35 Bay Area Compliance Laboratories Corp. (Shenzhen) Report No.: RSZ200519004- SA Page 14 of 35 Bay Area Compliance Laboratories Corp. (Shenzhen) Report No.: RSZ200519004- SA Page 15 of 35 Bay Area Compliance Laboratories Corp. (Shenzhen) Report No.: RSZ200519004- SA Page 16 of 35 Bay Area Compliance Laboratories Corp. (Shenzhen) Report No.: RSZ200519004- SA Page 17 of 35 Bay Area Compliance Laboratories Corp. (Shenzhen) Report No.: RSZ200519004- SA Page 18 of 35 Bay Area Compliance Laboratories Corp. (Shenzhen) Report No.: RSZ200519004- SA Page 19 of 35 Bay Area Compliance Laboratories Corp. (Shenzhen) Report No.: RSZ200519004- SA Page 20 of 35 Bay Area Compliance Laboratories Corp. (Shenzhen) Report No.: RSZ200519004- SA Page 21 of 35 Bay Area Compliance Laboratories Corp. (Shenzhen) Report No.: RSZ200519004- SA Page 22 of 35 Bay Area Compliance Laboratories Corp. (Shenzhen) Report No.: RSZ200519004- SA Page 23 of 35 Bay Area Compliance Laboratories Corp. (Shenzhen) Report No.: RSZ200519004- SA Page 24 of 35 Bay Area Compliance Laboratories Corp. (Shenzhen) Report No.: RSZ200519004- SA Page 25 of 35 Bay Area Compliance Laboratories Corp. (Shenzhen) Report No.: RSZ200519004- SA Page 26 of 35 Bay Area Compliance Laboratories Corp. (Shenzhen) Report No.: RSZ200519004- SA Page 27 of 35 Bay Area Compliance Laboratories Corp. (Shenzhen) Report No.: RSZ200519004- SA Page 28 of 35 Bay Area Compliance Laboratories Corp. (Shenzhen) Report No.: RSZ200519004- SA Page 29 of 35 Bay Area Compliance Laboratories Corp. (Shenzhen) Report No.: RSZ200519004- SA Page 30 of 35 Bay Area Compliance Laboratories Corp. (Shenzhen) Report No.: RSZ200519004- SA Page 31 of 35 Bay Area Compliance Laboratories Corp. (Shenzhen) Report No.: RSZ200519004- SA Page 32 of 35 Bay Area Compliance Laboratories Corp. (Shenzhen) Report No.: RSZ200519004- SA Page 33 of 35 Bay Area Compliance Laboratories Corp. (Shenzhen) Report No.: RSZ200519004- SA Page 34 of 35 Bay Area Compliance Laboratories Corp. (Shenzhen) Report No.: RSZ200519004- SA Page 35 of 35

Bay Area Compliance Laboratories Corp. (Shenzhen) Report No.: RSZ200519004-SA Page 1 of 84 Test Plot 1#: GSM 850_Head Left Cheek_Middle DUT: Smart Phone; Type: K57; Serial: RSZ200519004-SA-S1; Communication System: Generic GSM; Frequency: 836.6 MHz;Duty Cycle: 1:8 Medium parameters used: f = 836.6 MHz; σ = 0.929 S/m; ε r = 41.702; ρ = 1000 kg/m 3 ; Phantom section: Left Section DASY5 Configuration:  Probe: EX3DV4 - SN7522; ConvF(9.92, 9.92, 9.92) @836.6 MHz  Sensor-Surface: 4mm (Mechanical Surface Detection)  Electronics: DAE4 SN1562;Calibrated: 2020/03/03  Phantom: SAM-Twin V8.0 P1aP2a; Type: QD 000 P41 AA; Serial: 1962  Measurement SW: DASY52, Version 52.10 (2) ; Area Scan (71x91x1): Interpolated grid: dx=1.500 mm, dy=1.500 mm Maximum value of SAR (interpolated) = 0.247 W/kg Zoom Scan (5x5x7)/Cube 0: Measurement grid: dx=8mm, dy=8mm, dz=5mm Reference Value = 4.739 V/m; Power Drift = 0.08 dB Peak SAR (extrapolated) = 0.309 W/kg SAR(1 g) = 0.244 W/kg; SAR(10 g) = 0.186 W/kg Maximum value of SAR (measured) = 0.254 W/kg 0 dB = 0.254 W/kg = -5.95 dBW/kg Bay Area Compliance Laboratories Corp. (Shenzhen) Report No.: RSZ200519004-SA Page 2 of 84 Test Plot 2#: GSM 850_Head Left Tilt_Middle DUT: Smart Phone; Type: K57; Serial: RSZ200519004-SA-S1; Communication System: Generic GSM; Frequency: 836.6 MHz;Duty Cycle: 1:8 Medium parameters used: f = 836.6 MHz; σ = 0.929 S/m; ε r = 41.702; ρ = 1000 kg/m 3 ; Phantom section: Left Section DASY5 Configuration:  Probe: EX3DV4 - SN7522; ConvF(9.92, 9.92, 9.92) @836.6 MHz  Sensor-Surface: 4mm (Mechanical Surface Detection)  Electronics: DAE4 SN1562;Calibrated: 2020/03/03  Phantom: SAM-Twin V8.0 P1aP2a; Type: QD 000 P41 AA; Serial: 1962  Measurement SW: DASY52, Version 52.10 (2) ; Area Scan (71x91x1): Interpolated grid: dx=1.500 mm, dy=1.500 mm Maximum value of SAR (interpolated) = 0.151 W/kg Zoom Scan (5x5x7)/Cube 0: Measurement grid: dx=8mm, dy=8mm, dz=5mm Reference Value = 7.947 V/m; Power Drift = -0.10 dB Peak SAR (extrapolated) = 0.176 W/kg SAR(1 g) = 0.145 W/kg; SAR(10 g) = 0.114 W/kg Maximum value of SAR (measured) = 0.150 W/kg 0 dB = 0.150 W/kg = -8.24 dBW/kg Bay Area Compliance Laboratories Corp. (Shenzhen) Report No.: RSZ200519004-SA Page 3 of 84 Test Plot 3#: GSM 850_Head Right Cheek_Middle DUT: Smart Phone; Type: K57; Serial: RSZ200519004-SA-S1; Communication System: Generic GSM; Frequency: 836.6 MHz;Duty Cycle: 1:8 Medium parameters used: f = 836.6 MHz; σ = 0.929 S/m; ε r = 41.702; ρ = 1000 kg/m 3 ; Phantom section: Right Section DASY5 Configuration:  Probe: EX3DV4 - SN7522; ConvF(9.92, 9.92, 9.92) @836.6 MHz  Sensor-Surface: 4mm (Mechanical Surface Detection)  Electronics: DAE4 SN1562;Calibrated: 2020/03/03  Phantom: SAM-Twin V8.0 P1aP2a; Type: QD 000 P41 AA; Serial: 1962  Measurement SW: DASY52, Version 52.10 (2) ; Area Scan (71x91x1): Interpolated grid: dx=1.500 mm, dy=1.500 mm Maximum value of SAR (interpolated) = 0.253 W/kg Zoom Scan (5x5x7)/Cube 0: Measurement grid: dx=8mm, dy=8mm, dz=5mm Reference Value = 4.937 V/m; Power Drift = 0.12 dB Peak SAR (extrapolated) = 0.292 W/kg SAR(1 g) = 0.243 W/kg; SAR(10 g) = 0.190 W/kg Maximum value of SAR (measured) = 0.252 W/kg 0 dB = 0.252 W/kg = -5.99 dBW/kg Bay Area Compliance Laboratories Corp. (Shenzhen) Report No.: RSZ200519004-SA Page 4 of 84 Test Plot 4#: GSM 850_Head Right Tilt_Middle DUT: Smart Phone; Type: K57; Serial: RSZ200519004-SA-S1; Communication System: Generic GSM; Frequency: 836.6 MHz;Duty Cycle: 1:8 Medium parameters used: f = 836.6 MHz; σ = 0.929 S/m; ε r = 41.702; ρ = 1000 kg/m 3 ; Phantom section: Right Section DASY5 Configuration:  Probe: EX3DV4 - SN7522; ConvF(9.92, 9.92, 9.92) @836.6 MHz  Sensor-Surface: 4mm (Mechanical Surface Detection)  Electronics: DAE4 SN1562;Calibrated: 2020/03/03  Phantom: SAM-Twin V8.0 P1aP2a; Type: QD 000 P41 AA; Serial: 1962  Measurement SW: DASY52, Version 52.10 (2) ; Area Scan (71x91x1): Interpolated grid: dx=1.500 mm, dy=1.500 mm Maximum value of SAR (interpolated) = 0.159 W/kg Zoom Scan (5x5x7)/Cube 0: Measurement grid: dx=8mm, dy=8mm, dz=5mm Reference Value = 7.744 V/m; Power Drift = 0.14 dB Peak SAR (extrapolated) = 0.189 W/kg SAR(1 g) = 0.153 W/kg; SAR(10 g) = 0.118 W/kg Maximum value of SAR (measured) = 0.159 W/kg 0 dB = 0.159 W/kg = -7.99 dBW/kg Bay Area Compliance Laboratories Corp. (Shenzhen) Report No.: RSZ200519004-SA Page 5 of 84 Test Plot 5#: GSM 850_Body Worn Back_Middle DUT: Smart Phone; Type: K57; Serial: RSZ200519004-SA-S1; Communication System: Generic GSM; Frequency: 836.6 MHz;Duty Cycle: 1:8 Medium parameters used: f = 836.6 MHz; σ = 0.929 S/m; ε r = 41.702; ρ = 1000 kg/m 3 ; Phantom section: Flat Section DASY5 Configuration:  Probe: EX3DV4 - SN7522; ConvF(9.92, 9.92, 9.92)@836.6 MHz  Sensor-Surface: 4mm (Mechanical Surface Detection)  Electronics: DAE4 SN1562;Calibrated: 2020/03/03  Phantom: ELI V8.0 P1aP2a; Type: QD OVA 004 AA; Serial: 2092  Measurement SW: DASY52, Version 52.10 (2) ; Area Scan (71x131x1): Interpolated grid: dx=1.500 mm, dy=1.500 mm Maximum value of SAR (interpolated) = 0.249 W/kg Zoom Scan (5x5x7)/Cube 0: Measurement grid: dx=8mm, dy=8mm, dz=5mm Reference Value = 16.74 V/m; Power Drift = -0.14 dB Peak SAR (extrapolated) = 0.296 W/kg SAR(1 g) = 0.233 W/kg; SAR(10 g) = 0.176 W/kg Maximum value of SAR (measured) = 0.244 W/kg 0 dB = 0.244 W/kg = -6.13 dBW/kg Bay Area Compliance Laboratories Corp. (Shenzhen) Report No.: RSZ200519004-SA Page 6 of 84 Test Plot 6#: GSM 850_Body Back_Middle DUT: Smart Phone; Type: K57; Serial: RSZ200519004-SA-S1; Communication System: Generic GPRS-2 slots; Frequency: 836.6 MHz;Duty Cycle: 1:4 Medium parameters used: f = 836.6 MHz; σ = 0.929 S/m; ε r = 41.702; ρ = 1000 kg/m 3 ; Phantom section: Flat Section DASY5 Configuration:  Probe: EX3DV4 - SN7522; ConvF(9.92, 9.92, 9.92)@836.6 MHz  Sensor-Surface: 4mm (Mechanical Surface Detection)  Electronics: DAE4 SN1562;Calibrated: 2020/03/03  Phantom: ELI V8.0 P1aP2a; Type: QD OVA 004 AA; Serial: 2092  Measuremen…

Text truncated - open the document above for the full version.

Bay Area Compliance Laboratories Corp. (Shenzhen) Report No.: RSZ200519004- SA Page 1 of 5 APPENDIX B EUT TEST POSITION PHOTOS Liquid depth ≥ 15cm • Phantom: SAM-Twin V8.0 P1aP2a; Type: QD 000 P41 AA ; Serial: 1962 Head Left Cheek Setup Photo Bay Area Compliance Laboratories Corp. (Shenzhen) Report No.: RSZ200519004- SA Page 2 of 5 Head Left Tilt Setup Photo Head Right Cheek Setup Photo Bay Area Compliance Laboratories Corp. (Shenzhen) Report No.: RSZ200519004- SA Page 3 of 5 Head Right Tilt Setup Photo Body (Worn) Back Setup Photo (10mm) 10 mm Bay Area Compliance Laboratories Corp. (Shenzhen) Report No.: RSZ200519004- SA Page 4 of 5 Body Bottom Setup Photo (10mm) Body Left Setup Photo (10mm) 10 mm 10 mm Bay Area Compliance Laboratories Corp. (Shenzhen) Report No.: RSZ200519004- SA Page 5 of 5 Body Right Setup Photo (10mm) 10 mm

Note: This report must not be used by the customer to claim product certification, approval, or endorsement by A2LA* or any agency of the Federal Government. This report may contain data that are not covered by the A2LA accreditation and are marked with an asterisk “★”. BACL is not responsible for the authenticity of any test data provided by the applicant. Data included from the applicant that may affect test results are marked with an asterisk ’*’. Customer model name, addresses, names, trademarks etc. are not considered data. This report cannot be reproduced except in full, without prior written approval of the Company. Unless otherwise stated the results shown in this test report refer only to the sample(s) tested. This report is valid only with a valid digital signature. The digital signature may be available only under the Adobe software above version 7.0. FCC PART 27 FCC PART 22H, PART 24E TEST REPORT For KRIPTO MOBILE CORPORATION 7236 NW 31ST ST., MIAMI Florida United States FCC ID:2APX7K57 R e p o r t T y p e : O r i gi n a l R e p o r t P r o d u c t T y p e : S ma r t P h o n e Report Number: RSZ200519004-00D Report Date: 2020-06-15 Reviewed By: Jimmy Xiao RF Engineer Prepared By: Bay Area Compliance Laboratories Corp. (Shenzhen) 6/F., West Wing, Third Phase of Wanli Industrial Building, Shihua Road, Futian Free Trade Zone, Shenzhen, Guangdong, China Tel: +86-755-33320018 Fax: +86-755-33320008 www.baclcorp.com.cn Bay Area Compliance Laboratories Corp. (Shenzhen) Report No.: RSZ200519004-00D FCC Part 27, FCC Part 22H/24E Page 2 of 134 TABLE OF CONTENTS GENERAL INFORMATION ....................................................................................................................................... 4 PRODUCT DESCRIPTION FOR EQUIPMENT UNDER TEST (EUT) ..................................................................................... 4 OBJECTIVE ................................................................................................................................................................... 4 RELATED SUBMITTAL(S)/GRANT(S) ............................................................................................................................. 4 TEST METHODOLOGY .................................................................................................................................................. 5 MEASUREMENT UNCERTAINTY .................................................................................................................................... 5 TEST FACILITY ............................................................................................................................................................. 5 SYSTEM TEST CONFIGURATION .......................................................................................................................... 6 DESCRIPTION OF TEST CONFIGURATION ...................................................................................................................... 6 EQUIPMENT MODIFICATIONS ....................................................................................................................................... 6 SUPPORT EQUIPMENT LIST AND DETAILS .................................................................................................................... 6 BLOCK DIAGRAM OF TEST SETUP ................................................................................................................................ 6 SUMMARY OF TEST RESULTS ............................................................................................................................... 7 TEST EQUIPMENT LIST ........................................................................................................................................... 8 FCC §1.1307(B) & §2.1093 - RF EXPOSURE INFORMATION ............................................................................ 10 APPLICABLE STANDARD ............................................................................................................................................ 10 TEST RESULT ............................................................................................................................................................. 10 FCC §2.1047 - MODULATION CHARACTERISTIC ............................................................................................ 11 FCC § 2.1046, § 22.913 (A) & § 24.232 (C); §27.50 (D) (H) - RF OUTPUT POWER ........................................... 12 APPLICABLE STANDARD ............................................................................................................................................ 12 TEST PROCEDURE ...................................................................................................................................................... 12 TEST DATA ................................................................................................................................................................ 12 FCC §2.1049, §22.917, §22.905 & §24.238 & §27.53 - OCCUPIED BANDWIDTH .............................................. 32 APPLICABLE STANDARD ............................................................................................................................................ 32 TEST PROCEDURE ...................................................................................................................................................... 32 TEST DATA .............................................................................................................................................................…

Text truncated - open the document above for the full version.