2APXNLACA128Wireless Charging Stand

PACKAGE CONTENTS • 10 W Qi Charging Phone Stand • 3 ft. (0.9 m) charging cable • USB wall adapter • Quick Setup Guide FEATURES • Angled stand displays your screen while charging • 10 W output fast charges Qi-compatible smartphones • Rubber pads keep your phone secure and the base from sliding • Blue LED shows when your device is charging • Ideal for your nightstand, desk, or table Before using your new product, please read these instructions to prevent any damage. PRODUCT OVERVIEW USING YOUR CHARGING PAD 1 Plug one end of the USB cable into the Micro USB port on the back of your charging pad. 2 Plug the other end of the USB cable into a USB wall charger. 3 Place your Qi-enabled device on the center of your charging pad with the screen facing up. The LED is blue when your device is charging. Note: If the LED is red, your device is not charging. See “TROUBLESHOOTING” for more information . QUICK SETUP GUIDE 10 Watt Qi Charging Phone Stand NS-MWPC10KS Flat size (W×H): 12 × 2.75 in. (304.8 x 69.85 mm) Final folded size: 3 × 2.75 in. (76.2 x 69.85 mm) COMPATIBILITY Qi-enabled devices up to 10 W. Any Qi-compatible smartphones. LED indicator Back Front Micro-USB port Back Charging cable NS-MWPC10KS_20-0033_QSG_V1_EN_Final.ai 1 4/27/2020 8:50:36 AMNS-MWPC10KS_20-0033_QSG_V1_EN_Final.ai 1 4/27/2020 8:50:36 AM environnement non controlé. Cet équipement doit être installé et utilisé avec une Cet équipement est conforme aux limites d'exposition aux radiations IC CNR-102 établies pour un environment. This equipment should be installed and operated with minimum distance 20cm This equipment complies with IC RSS-102 radiation exposure limits set forth for an uncontrolled aux CNR d’Innovation, Sciences et Développement économique Canada applicables aux (2) This device must accept any interference, including interference that may cause undesired. (1) This device may not cause interference. RSS statement:This device contains licence-exempt transmitter(s)/receiver(s) that comply V1 ENGLISH 20-0033 Device charges slowly • Your device may charge more slowly with the charging pad than a charging cable. This is normal behavior. • Make sure that your device is positioned in the center of your charging pad. CAUTION: Only use the cable with the wall charger that came with your charger. Using a different cable and wall charger can decrease charging performance or damage your charger. SPECIFICATIONS Qi Wireless Charging Pad: Input: DC 5-12V 2A max. Output: 10 W max. Dimensions: 3.1 x 3.1 x 4.4 in. (80 x 80 x 112.6 mm) AC power adapter: Input: 100 -240 V ~ 50/60 Hz .45 A Output: DC 5V/3 A, 9V/2 A, 12V/1.5 A Charging cable: 3 ft. (0.9 m) LEGAL NOTICES FCC Information FCC Caution: Changes or modifications not expressly approved by the party responsible for compliance could void the user's authority to operate the equipment. FCC Statement: This equipment has been tested and found to comply with the limits for a Class B digital device, pursuant to part 15 of the FCC Rules. These limits are designed to provide reasonable protection against harmful interference in a residential installation. This equipment generates, uses, and can radiate radio frequency energy and, if not installed and used in accordance with the instructions, may cause harmful interference to radio communications. However, there is no guarantee that interference will not occur in a particular installation. If this equipment does cause harmful interference to radio or television reception, which can be determined by turning the equipment off and on, the user is encouraged to try to correct the interference by one or more of the following measures: • Reorient or relocate the receiving antenna. • Increase the separation between the equipment and receiver. • Connect the equipment into an outlet on a circuit different from that to which the receiver is connected. • Consult the dealer or an experienced radio/TV technician for help. FCC statement: This device complies with part 15 of the FCC Rules. Operation is subject to the following two conditions: (1) This device may not cause harmful interference, and (2) this device must accept any interference received, including interference that may cause undesired operation. This equipment complies with FCC radiation exposure limits set forth for an uncontrolled environment. This equipment should be installed and operated with minimum distance 20cm between the radiator and your body. This transmitter must not be co-located or operating in conjunction with any other antenna or transmitter. SAFETY INFORMATION • Avoid dropping. • Do not disassemble. • Do not place metal objects between devices and the wireless charging pads. • Thick protective case (≥ .2 in. [5 mm]) or a case that includes a magnet or metallic material, may not allow proper charging function. • Keep wireless charging pad away from any liquid or moisture. • The maximum ambient temperature during use of this product must not exceed 113° F (45° C). • Do not place this device in fire or other excessively hot environments. • Must use provided adapter for proper function, if not it may be malfunction. ONE-YEAR LIMITED WARRANTY Visit www.insigniaproducts.com for details. CONTACT INSIGNIA: 1-877-467-4289 (U.S. and Canada) 1-800-926-3000 (Mexico) www.insigniaproducts.com INSIGNIA is a trademark of Best Buy and its affiliated companies Distributed by Best Buy Purchasing, LLC 7601 Penn Ave South, Richfield, MN 55423 U.S.A. ©2020 Best Buy. All rights reserved. LED INDICATOR STATUS TROUBLESHOOTING Device not charging/LED is red • Make sure that your device is Qi-enabled. • Make sure that your charging pad is connected to a working power outlet. • Make sure that your device is positioned correctly on your charging pad. • Make sure that there are no other objects on the charging pad. • Remove your device’s case. It may be blocking the wireless signal. LED Blinking blue Solid blue Blue and red both on Solid red Blinking red STATUS Standby Charging Quick charging Insuffi…

Text truncated - open the document above for the full version.

ASAP Technology (Jiangxi) Co., Ltd Model difference list To who concerns: ASAP TECHNOLOGY (jiangxi) CO., LTD hereby Model LACA128,NS-MWPC10KS,NS-MWPC10xxxxxx,MD-MWPC10xxxx xx,DX-MWPC10xxxxxx,PT-MWPC10xxxxxx,RF-MWPC10xxxxxx (‘x’ can be A-Z, a-z, 0-9, - or blank) are identical for market purpose only, except the model name) (Trademark: INSIGNIA) Sincerely, Manager By: Mr Xiaolan Deng (Signature/Title) (Print name)

Sample Agency Request Letter QF094234 Page 1 of 1 Revision 0 Authority to Act as Agent Date: 2020-04-08 TUV Rheinland Group 762 Park Avenue Youngsville, NC 27596 To Whom It May Concern: I appoint Mr. Jonathan Li of TUV Rheinland (Shenzhen) Co., Ltd. to act as our agent in the preparation of this application for equipment certification. I certify that submitted documents properly describe the device or system for which equipment certification is sought. I also certify that each unit manufactured, imported or marketed, as defined in the FCC or Industry Canada’s regulations will have affixed to it a label identical to that submitted for approval with this application. For instances where our authorized agent signs the application for certification on our behalf, I acknowledge that all responsibility for complying with the terms and conditions for Certification, as specified by TUV Rheinland Group, still resides with ASAP TECHNOLOGY (jiangxi) CO., LTD / No.5, Shuguang Rd, West Zone, Ji'an County Industrial Park, Ji’an, Jiangxi 343100 China For TCB applications, We certify that we are not subject to denial of federal benefits, that includes FCC benefits, pursuant to Section 5301 of the Anti-Drug Abuse Act of 1988, 21 U.S.C. 862. Further, no party, as defined in 47 CFR 1.2002 (b), to the application is subject to denial of federal benefits, that includes FCC benefits. Thank you, Agency Agreement Expiration Date: 12 months By : Mr. Xiaolan Deng (Signature) (Print Name) Title : Manager Te le phone : +86 796 7118988 On be half of : ASAP TECHNOLOGY (jiangxi) CO., LTD (Company Name)

ASAP Technology (Jiangxi) Co., Ltd Confidentiality Letter Date: 2020-04-08 Subject: Confidentiality Request for FCC ID: 2APXNLACA128 and IC ID: 24654-LACA128 Pursuant to FCC 47 CRF 0.457(d) and 0.459 and IC RSP-100, Section 10, the applicant requests that a part of the subject FCC/IC application be held confidential. Type of Confidentiality Requested Exhibit Short Term Permanent Block Diagrams Short Term External Photos Short Term Permanent Internal Photos Short Term Permanent Operation Description/Theory of Operation Short Term Permanent Part List/Tune-Up Procedure Short Term Permanent Schematics Short Term Test Setup Photos Short Term Permanent User’s Manual ASAP Technology(Jiangxi) Co., Ltd has spent substantial effort in developing this product and it is one of the first of its kind in industry. Having the subject information easily available to "competition" would negate the advantage they have achieved by developing this product. Not protecting the details of the design will result in financial hardship. Permanent Confidentiality: The applicant requests the exhibits listed above as permanently confidential be permanently withheld from public review due to materials that contain trade secrets and proprietary information not customarily released to the public. Short-Term Confidentiality: The applicant requests the exhibits selected above as short term confidential be withheld from public view for a period of 180 days from the date of the Grant of Equipment Authorization and prior to marketing. This is to avoid premature release of sensitive information prior to marketing or release of the product to the public. Applicant is also aware that they are responsible to notify TUV Rheinland in the event information regarding the product or the product is made available to the public. TUV Rheinland will then release the documents listed above for public disclosure pursuant to FCC Public Notice DA 04- 1705. Sincerely, Manager By: Mr Xiaolan Deng (Signature/Title) (Print name)

Page 1 of 3 FCC ID: 2APXNLACA128 IC: 24654-LACA128 Page 2 of 3 FCC ID: 2APXNLACA128 IC: 24654-LACA128 Page 3 of 3 FCC ID: 2APXNLACA128 IC: 24654-LACA128

-C

Page 1 of 3 FCC ID: 2APXNLACA128 IC: 24654-LACA128 Page 2 of 3 FCC ID: 2APXNLACA128 IC: 24654-LACA128 Page 3 of 3 FCC ID: 2APXNLACA128 IC: 24654-LACA128

FCC ID: 2APXNLACA128 1.1. Measuring Standard FCC CFR 47 Part 1(1.1310) KDB 680106 D01 v03 1.2. Requirements The EUT does comply with item 5(b) of KDB 680106 D01 v03 1) Power transfer frequency is less than 1MHz 2) Output power from each primary coil is less than or equal to 15 watts. 3) The transfer system includes only single primary and secondary coils. This includes charging systems that may have multiple primary coils and clients that able to detect and allow coupling only between individual pair of coils. 4) Client device is inserted in or placed directly in contact with the transmitter. 5) Mobile exposure conditions only (portable exposure conditions are not covered by this exclusion) 6) The aggregate H-field strengths at 15 cm surrounding the device and 20 cm above the top surface from all simultaneous transmitting coils are demonstrated to be less than 50% of the MPE limit. 1.3. Test Configuration 1) The field strength of both H-field was measured at 15cm using the equipment list above for determining compliance with the MPE requirements of FCC Part 1.1310. 2) The RF power density was measured at Under maximum load test 3) Maximum H-field measurements were made 15cm from each side of the EUT. Along the side of the EUT and still 15cm away from the edge of the EUT, the field probes were positioned at the location where there is maximum field strength. The maximum H-field is reported below. 4) This device uses a wireless charging circuit for power transfer operating at the frequency of 110 – 205 kHz. Thus, the 300kHz limits were used: H-field limit 1.63 (A/m). 1.4. Test Procedure 1) The RF exposure test was performed in anechoic chamber. 2) The aggregate H-field strengths at 15 cm surrounding the device and 20 cm above the top surface 3) The highest emission level was recorded and compared with limit as soon as measurement of each points (A, B, C, D, E) were completed. 4) The EUT was measured according to the dictates of KDB 680106 D01 v03. Remark: The EUT’s test position A, B, C, D, and E is valid for the H field measurements. 1.5. Test Setup 1.6. Limits Remark: Emissions between 100 kHz to 300 kHz should be assessed versus the limits at 300 kHz in Table 1 of Section 1.1310: 1.63 A/m 1.7. Measuring Device and Test Equipment For MPE Measurement Item Equipment Manufacturer Model No. Serial No. Last Cal. Cal. Interval 1. H-Field Probe 100 cm2 SENSOR narda D-0010 BN 2300/90.10 May 20, 2019 1 Year 2. MAGNETIC FIELD HiTESTER ELT- 400 narda D-0009 BN 2304/03 May 20, 2019 1 Year 1.8. Description of Test Facility Test Items : H field measurements Test Laboratory : TÜV Rheinland (Shenzhen) Co., Ltd. Site Location : East of F/1, F/2 - F/4, Building 1, Cybio Technology Building, No. 6 Langshan No. 2 Road, North Hi-tech Industry Park, Nanshan District, Shenzhen, P.R. China 1.9. Measuring Results Table: H-Field Strength at 15 cm from the edges surrounding the EUT and 20cm from the front surface of the EUT EUT Test Mode Measured H-Field Strength Values (A/m) 50% Limit (A/m) Limit (A/m) Test Position A （top） Test Position B(back) Test Position C(left) Test Position D (Right) Test Position E(Front) 1% Battery Level 0.345 0.332 0.325 0.332 0.366 0.815 1.63 50% Battery Level 0.327 0.308 0.312 0.324 0.332 0.815 1.63 99% Battery Level 0.366 0.335 0.326 0.337 0.363 0.815 1.63 IC:24654-LACA128 1.10. Measuring Standard RSS-102 Issue 5 1.11. 1.11.Requirements The maximum operating frequency of the device is 205 kHz Thus, the minimum limit for Canada is 0.73 / ƒ = 0.73 / 0.205 = 3.56 A/m >0.575 A/m => PASS 1.12. Test Procedure 5) The RF exposure test was performed in anechoic chamber. 6) The aggregate H-field strengths at 10 cm surrounding the device and 10 cm above the top surface 7) The highest emission level was recorded and compared with limit as soon as measurement of each points (A, B, C, D, E) were completed. Remark: The EUT’s test position A, B, C, D, and E is valid for the H field measurements. 1.13.Limits 1.14. Measuring Device and Test Equipment For MPE Measurement Item Equipment Manufacturer Model No. Serial No. Last Cal. Cal. Interval 1. H-Field Probe 100 cm2 SENSOR narda D-0010 BN 2300/90.10 May 20, 2019 1 Year 2. MAGNETIC FIELD HiTESTER ELT- 400 narda D-0009 BN 2304/03 May 20, 2019 1 Year 1.15. Description of Test Facility Test Items : H field measurements Test Laboratory : Test Laboratory Site Location : East of F/1, F/2 - F/4, Building 1, Cybio Technology Building, No. 6 Langshan No. 2 Road, North Hi-tech Industry Park, Nanshan District, Shenzhen, P.R. China 1.16. Measuring Results Table: H-Field Strength at 10 cm from the edges surrounding the EUT and 10cm from the top surface of the EUT EUT Test Mode Measured H-Field Strength Values (A/m) Limit (A/m) Test Position A （top） Test Position B(back) Test Position C(left) Test Position D (Right) Test Position E(Front) 1% Battery Level 0.345 0.319 0.325 0.345 0.378 3.56 50% Battery Level 0.319 0.308 0.312 0.333 0.354 3.56 99% Battery Level 0.353 0.335 0.326 0.342 0.398 3.56

Produkte Products Prüfbericht-Nr.: Test report No.: 60360725 001 Auftrags-Nr.: Order No.: 168154778 Seite 1 von 24 Page 1 of 24 Kunden-Referenz-Nr.: Client reference No.: N/A Auftragsdatum: Order date: 04.03.2020 Auftraggeber: Client: ASAP TECHNOLOGY (jiangxi) CO., LTD No.5, Shuguang Rd, West Zone, Ji'an County Industrial Park, Ji’an, Jiangxi 343100 China Prüfgegenstand: Test item: Wireless Charging Stand Bezeichnung / Typ-Nr.: Identification / Type No.: LACA128, NS-MWPC10KS, NS-MWPC10xxxxxx, MD-MWPC10xxxxxx, DX- MWPC10xxxxxx, PT-MWPC10xxxxxx, RF-MWPC10xxxxxx (‘x’ can be A-Z, a-z, 0-9, - or blank only for different models) (Trademark: INSIGNIA) Auftrags-Inhalt: Order content: FCC and IC approval Prüfgrundlage: Test specification: CFR47 FCC Part 15: Subpart C Section 15.201 CFR47 FCC Part 15: Subpart C Section 15.207 CFR47 FCC Part 15: Subpart C Section 15.209 CFR47 FCC Part 2: Subpart J Section 2.1091 RSS-216 issue 2 Janyary 2016 RSS-GEN issue 5 March 2019 RSS-102 issue 5 March 2015 Wareneingangsdatum: Date of receipt: 17.03.2020 Refer to photos document Prüfmuster-Nr.: Test sample No.: A001069150-025 to 026 Prüfzeitraum: Testing period: 18.03.2020 - 07.04.2020 Ort der Prüfung: Place of testing: TÜV Rheinland (Shenzhen) Co., Ltd. Prüflaboratorium: Testing laboratory: TÜV Rheinland (Shenzhen) Co., Ltd. Prüfergebnis*: Test result*: Pass geprüft von / tested by: kontrolliert von / reviewed by: 06.05.2020 Jonathan Li / Project Manager 06.05.2020 Winnie Hou / Technical Certifier Datum Date Name/Stellung Name/Position Unterschrift Signature Datum Date Name/Stellung Name/Position Unterschrift Signature Sonstiges / Other: FCC ID: 2APXNLACA128 IC: 24654-LACA128, HVIN: NS-MWPC10KS-C Zustand des Prüfgegenstandes bei Anlieferung: Condition of the test item at delivery: Prüfmuster vollständig und unbeschädigt Test item complete and undamaged: * Legende: 1 = sehr gut 2 = gut 3 = bef riedigend 4 = ausreichend 5 = mangelhalt P(ass) = entspricht o.g. Prüfgrundlage(n) F(ail) = entspricht nicht o.g. Prüfgrundlage(n) N/A = nicht anwendbar N/T = nicht getestet Legend: 1 = v ery good 2 = good 3 = satisfactory 4 = suf ficient 5 = poor P(ass) = passed a.m. test specifications(s) F(ail) = f ailed a.m. test specifications(s) N/A = not applicable N/T = not tested Dieser Prüfbericht bezieht sich nur auf das o.g. Prüfm uster und darf ohne Genehm igung der Prüfstelle nicht auszugsw eise vervielfältigt w erden. Dieser Bericht berechtigt nicht zur Verwendung eines Prüfzeichens. This test report only relates to the a. m. test sample. Without permission of the test center this test report is not permitted to be V04 duplicated in extracts. This test report does not entitle to carry any test mark. T ÜV Rheinland (Shenzhen) Co., Ltd., 1F East & 2-4F, Cybio T echnology Building No.1, No.16 Langshan 2nd Road, High-Tech Industrial Park North Nanshan District, 518057, Shenzhen, China http://www.tuv.com Produkte Products Prüfbericht - Nr.: Test Report No. 60360725 001 Seite 2 von 24 Page 2 of 24 Test Summary 5.1.1 ANTENNA REQUIREMENT RESULT: Pass 5.1.2 99% BANDWIDTH RESULT: Pass 5.1.3 RADIATED SPURIOUS EMISSIONS RESULT: Pass 5.1.4 CONDUCTED EMISSIONS RESULT: Pass Produkte Products Prüfbericht - Nr.: Test Report No. 60360725 001 Seite 3 von 24 Page 3 of 24 Contents 1 GENERAL REMARKS .......................................................................................................... 4 1.1 COMPLEMENTARY MATERIALS ............................................................................................. 4 2 TEST SITES ..................................................................................................................... 5 2.1 TEST FACILITIES ............................................................................................................... 5 2.2 LIST OF TEST AND MEASUREMENT INSTRUMENTS ..................................................................... 5 2.3 TRACEABILITY.................................................................................................................. 6 2.4 CALIBRATION................................................................................................................... 6 2.5 MEASUREMENT UNCERTAINTY ............................................................................................. 6 2.6 LOCATION OF ORIGINAL DATA ............................................................................................. 7 2.7 STATUS OF FACILITY USED FOR TESTING ............................................................................... 7 3 GENERAL PRODUCT INFORMATION........................................................................................ 8 3.1 PRODUCT FUNCTION AND INTENDED USE................................................................................ 8 3.2 RATINGS AND SYSTEM DETAILS ........................................................................................... 8 3.3 INDEPENDENT OPERATION MODES ........................................................................................ 8 3.4 NOISE GENERATING AND NOISE SUPPRESSING PARTS............................................................... 8 3.5 SUBMITTED DOCUMENTS .................................................................................................... 8 4 TEST SET-UP AND OPERATION MODES................................................................................... 9 4.1 PRINCIPLE OF CONFIGURATION SELECTION ............................................................................. 9 4.2 TEST OPERATION AND TEST SOFTWARE................................................................................. 9 4.3 SPECIAL ACCESSORIES AND AUXILIARY EQUIPMENT ................................................................. 9 4.4 COUNTERMEASURES TO ACHIEVE EMC COMPLIANCE ............................................................... 9 4.5 TEST SETUP DIAGRAM ..................................................................................................... 10…

Text truncated - open the document above for the full version.

Produkte Products Appendix A 60360725 001 Page 1 of 3 Appendix A: Photographs of the Test Set-Up APPENDIX A: PHOTOGRAPHS OF THE TEST SET-UP.................................................................................................................. 1 PHOTOGRAPH 1: SET-UP PHOTO FOR RADIATED EMISSION, 9KHZ - 30MHZ......................................................................................... 2 PHOTOGRAPH 2: SET-UP PHOTO FOR RADIATED EMISSION, 30MHZ - 1GHZ ........................................................................................ 2 PHOTOGRAPH 3: SET-UP PHOTO FOR CONDUCTED EMISSION ON AC MAINS ......................................................................................... 3 Produkte Products Appendix A 60360725 001 Page 2 of 3 Photograph 1: Set-up photo for Radiated Emission, 9KHz - 30MHz Photograph 2: Set-up photo for Radiated Emission, 30MHz - 1GHz Produkte Products Appendix A 60360725 001 Page 3 of 3 Photograph 3: Set-up photo for Conducted Emission on AC Mains

Page 1 of 1 FCC ID: 2APXNLACA128 IC: 24654-LACA128 MPE test photo