2APXNLACC137Wireless charger

Form: RFT-AMER-TCB-OP-19n Revision: 1 Page 1 of 1 Date: 1/25/2023 ASAP Technology (Jiangxi) Co., Ltd Attention: Application Examiner Re: Covered List, located at https://www.fcc.gov/supplychain/coveredlist and 47 CFR parts §2.903 and §2.911(d)(5)(ii) of the FCC rules Applicant: [ASAP Technology (Jiangxi) Co., Ltd] FCC ID: [2APXNLACC137] To whom it may concern, [ASAP Technology (Jiangxi) Co., Ltd] (“Applicant”) certifies that the equipment for which authorization is sought is not “covered” equipment prohibited from receiving an equipment authorization pursuant to 47 CFR part §2.903 of the FCC rules and does not originate directly or indirectly from any company named on the covered list located in the link above or any subsidiary or affiliate thereof. Applicant further certifies that, as of the date of the filing of the application, the Applicant [is not] identified on the Covered List as an entity producing “covered” equipment and is not a subsidiary or affiliate of any such entity pursuant to 47 CFR part §1.50002 and required by 47 CFR part §2.911(d)(5)(ii) of the FCC rules. I HEREBY CERTIFY THAT I am authorized to make the representations above on behalf of the Applicant and agree to immediately notify Intertek if there is any change in the status identified above. ______________________________ [Signature of authorized Proprietor, Partner or Authorized Officer] [Printed Name] Xiaolan Deng [Title] [Company name] ASAP Technology (Jiangxi) Co., Ltd [Date] 2024.5.9 Manager

Form: RFT-AMER-TCB-OP-19o Revision: 1 Page 1 of 1 Date: 1/25/2023 UNITED STATES DESIGNATED AGENT LETTER Attention: Application Examiner Re: Certification designating a U.S. agent for service of process pursuant to section 2.911(d)(7) of the FCC rules To whom it may concern, This letter is to confirm both [Luxshare-ICT Inc] (“Agent”) and [ASAP Technology (Jiangxi) Co., Ltd ] (“Applicant”) acknowledge consent to obligations of each party pursuant to 47 CFR part §2.911(d)(7) of the FCC rules in regard to the agent for service of process. I [Xiaolan Deng] HEREBY CERTIFY THAT I am authorized to make the representations above on behalf of the Applicant. I further acknowledge the requirement to maintain an agent extends for no less than one year after the termination of all marketing and importation or the conclusion of and commission-related proceeding involving the equipment and agree to immediately notify the FCC and Intertek if there is any change in the status identified above. Applicant Company Name : ASAP Technology (Jiangxi) Co., Ltd Contact Name : Xiaolan Deng Address : Ji’an Industrial Park, Ji’an, Jiangxi 343100 China Telephone No : + 86 7967118988 Email : [email protected] FCC ID : 2APXNLACC135、2APXNLACC136、2APXNLACC137 Applicant FRN : 0027557297 Signature: _______ _______________________ Date: ___________2024.5.16________________________ I [Kyle Liu] HEREBY CERTIFY THAT I am authorized to make the representations above on behalf of the Agent. I consent to the obligation to accept service of process on behalf of the applicant in regard to the FCC ID designated above. Agent Company Name : Luxshare-ICT Inc Contact Name : Kyle Liu Address : 480 N.McCarthy Blvd #280, Milpitas ,CA 95035 Telephone No : +1 408-957-0535 ext 59081 Email : [email protected] Agent FRN : 0033589201 Signature: ____________________________________ Date: __________________2024.5.16__________________

ASAP Technology (Jiangxi) Co., Ltd [2024.5.9] Federal Communications Commission 445 12 th Street SW Washington, DC 20554 Subject: Limited Agency Agreement (ASAP Technology (Jiangxi) Co., Ltd) FCC ID: (2APXNLACC137 ) To Whom It May Concern: We, (ASAP Technology (Jiangxi) Co., Ltd), hereby authorized Intertek Testing Services to act as our Agent for the purpose of preparing application for FCC ID number (2APXNLACC137) under all applicable parts of the FCC rules and regulations. The effective date of this limited agency agreement is (2024.5.9). The Limited Agency Agreement expires on (2028.5.10), unless sooner terminated or extended by written notice to Intertek Testing Services and the Federal Communications Commission. This is to advise that we are in full compliance with the Anti-Drug Abuse Act. The applicant is not subject to a denial of federal benefits pursuant to Section 5301 of the Anti-Drug Act of 1988, 21 U.S.C. 862, and no party to the application is subject to a denial of federal benefits pursuant to that section. If you have any questions or comments, please do not hesitate to contact me. Sincerely, [Signature] [Type Name] Xiaolan Deng [Type Title] Manager

1(2) ASAP Technology (Jiangxi) Co., Ltd Attention: Certification reviewer RE: Request for Confidentiality FCC ID: 2APXNLACC137 To Whom It May Concern: Permanent Confidentiality [Complete this section if permanent confidentiality is requested] Request to withhold permanently from public review certain portions of the application for equipment certification for the referenced FCC identifiers. This request for confidentiality is made pursuant to 47 CFR 0.457(d) and 0.459 of the FCC Rules. In particular, the following sections of the application are to be kept permanently confidential: [Select one or more of items below, as appropriate] Schematics Block Diagrams Operational Description Tune-up Procedure Parts List Internal Photos (see note) Users Manual (see note) Note 1: Internal Photos may be held confidential 1) if the circuit board or internal components are not accessible to users. For example, it is acceptable if the circuit board is enclosed in epoxy. 2) Also, it is acceptable if the device is not accessible to the public, for example, a device mounted on the top of a large tower (or in a fenced enclosure) such that it is only serviceable by professional designated technicians under a Non-Disclosure Agreement (NDA). All sales for these devices must be under a NDA restricting the disclosure of the propriety information, including internal photos. Users Manual may be held confidential only when the manual contains proprietary technical information intended for professional technicians obligated under a NDA. All sales and distribution of the user’s manual must be under a NDA that restricts the disclosure of the information. In the application cover letter requesting permanent confidentiality the following additional description and the NDA exhibit is required: 1. Describe in detail how internal photos and/or users manual information are controlled to prevent them from becoming public or disclosed to unauthorized persons. 2. Describe how public access is restricted for products serviceable by professional designated technicians. 3. A statement that all sales of the non-consumer device will be under a NDA to include third party sales and that the final user of the device is subject to the NDA. 4. Provide an example of the NDA between the grantee and a purchaser. The request for confidentiality must Note 2: For scanning receiver, the schematics, block diagrams, operational description, tune-up procedure, parts list and internal photos are always held permanently confidential. □ √ Short-term Confidentiality [Complete this section if short-term confidentiality is requested] Request to withhold from public review for a period of 90 days from the date of the Grant of Equipment Authorization and prior to marketing, certain portions of the application for equipment certification for the referenced FCC identifiers. This request for confidentiality is made pursuant to 47 CFR 0.457(d) and 0.459 of the FCC Rules. In particular, the following sections of the application are to be kept short-term confidential for a period above from the date of the grant [Select one or more of items below that are not selected in the list above, as appropriate] □ √ Schematics □ √ Block diagrams □ √ Operational Description 2(2) □ Tune-up Procedure □ Parts List  Test Setup Photos  External Photos □ √ Internal Photos □ √ Users Manual Rationale for request for confidentiality: We have invested considerable time and materials in research and de velopment to produce the referenced product. Permanent confidentiality: Disclosure of the permanently confidential portions of this application to competitors would not only give them significant competitive advantages in de veloping similar products, but would also disclose successful implementation of unpublished, leading edge technology developed by us. □ √ Short-term confidentiality: Disclosure of the short-term confidential portions of this application during the period of importation and/or distribution would reveal key aspects of proprietary technology to competitors and diminish the value of our investment in research and development. If you have questions or need further information, please contact the undersigned. Sincerely, _________________ [Name of the applicant/grantee contact of FCC] [Title] [Date]2024.5.14 Manager Xiaolan Deng

7 8 6 4 3 21 7 8 6 5 4 3 21 .XXX± 0.100 .XX± 0.20 .X± 0.3 X.± 1 .XX°±0.3 .X°±0.5 .XXX°±0.1 X.°±1 PART NO. DWG NO: TITLE: SHEET SCALE 1:3 1/8 REV. OF LUXSHARE-TECH THESE DRAWINGS AND SPECIFICATIONS WITHOUT THE PRIOR WRITTEN CONSENT AND SHALL NOT BE REPRODUCED, COPIED OR CUED IN ANY MANNER UNITS: mm LUXSHARE-TECH ARE THE PROPERTY OF LUXSHARE-TECH RoHS DATE APPROVAL DESCRIPTION DESIGN REV. A1 Reach CP65 LACC137无线充10W(Qi)直连USB-A 3FT黑色（无包材） DRAW: CHKD: APPD: Safety Eng: SHUIPING ZHOU SHIHAO XIE Juan Luo XIONGWU LI A1 NEW SHIHAO XIE XIONGWU LI 2024/03/16 A 向 90° 69°±0.3° 65° 88.87 9.2±0.3 Wireless Charger Model:080-08-4962 FCC ID:2APXNLACC137 Input: 5V 3A/9V 2A/12V 1.5A. Output: 10W Max. This device complies with part 15 of the FCC Rules. Operation is subject to the following two conditions: (1)this device may not cause harmful interference,and (2)this device must accept any interference received, including interference that may cause undesired operation. MADE IN VIETNAM 24XXB Arial 1.5mm A向视图 11±0.3 16.8±0.3 52.41 丝印颜色: Gray 9 C 符号居中 116.6±0.3 白色灯光 R20 LUZWC003-CS-R1 50.5±0.3 25.2±0.3 2 3 70.5±0.3 1 4 138.8±0.3 Font: Font height: 7 8 6 4 3 21 7 8 6 5 4 3 21 .XXX± 0.100 .XX± 0.20 .X± 0.3 X.± 1 .XX°±0.3 .X°±0.5 .XXX°±0.1 X.°±1 PART NO. DWG NO: TITLE: SHEET SCALE 1:3 1/8 REV. OF LUXSHARE-TECH THESE DRAWINGS AND SPECIFICATIONS WITHOUT THE PRIOR WRITTEN CONSENT AND SHALL NOT BE REPRODUCED, COPIED OR CUED IN ANY MANNER UNITS: mm LUXSHARE-TECH ARE THE PROPERTY OF LUXSHARE-TECH A1 DRAW: CHKD: APPD: Safety Eng: SHUIPING ZHOU SHIHAO XIE Juan Luo XIONGWU LI 印字图 Wireless Charger Model:080-08-4962 FCC ID:2APXNLACC137 Input: 5V 3A/9V 2A/12V 1.5A. Output: 10W Max. This device complies with part 15 of the FCC Rules Operation is subject to the following two conditions: (1)this device may not cause harmful interference,and (2)this device must accept any interference received, including interference that may cause undesired operation. MADE IN VIETNAM 24XXB LACC137无线充10W(Qi)直连USB-A 3FT黑色（无包材） LUZWC003-CS-R1 YY WW vendor code (Fixed value) font height:1.5 process:laser carving date code Font Arial 7 8 6 4 3 21 7 8 6 5 4 3 21 .XXX± 0.100 .XX± 0.20 .X± 0.3 X.± 1 .XX°±0.3 .X°±0.5 .XXX°±0.1 X.°±1 PART NO. DWG NO: TITLE: SHEET SCALE 1:3 1/8 REV. OF LUXSHARE-TECH THESE DRAWINGS AND SPECIFICATIONS WITHOUT THE PRIOR WRITTEN CONSENT AND SHALL NOT BE REPRODUCED, COPIED OR CUED IN ANY MANNER UNITS: mm LUXSHARE-TECH ARE THE PROPERTY OF LUXSHARE-TECH A1 DRAW: CHKD: APPD: Safety Eng: SHUIPING ZHOU SHIHAO XIE Juan Luo XIONGWU LI 爆炸图 ITEMNAMEDESCRIPTION Q'TYUNIT 1 2 3 4 1 5 1 6 7 8 Cable 底盖 脚垫 螺丝 -C1010-F-A-+-镀黑锌-M2.0*7-H 塑壳-底盖-PC-黑色-V0-70.5*82.5*24.8-纹面-丝印-R U2-A TO OPEN-3FT-PVC-黑色-OD3.2-RS 塑壳-主壳-PC-黑色-V0-131*70.5*7.4-纹面-R 1 4 pcs 1 PCBALACC137无线充10W(Qi)主板（SMT） pcs pcs pcs pcs 主壳 9 10 11 12 螺丝 硅胶件 -脚垫-黑色-背胶-纹面-26*7*1-R 8 pcs 螺丝 Coil,JUYUAN,MP-A20-TX,6.9μH,R1 pcs 导光柱 螺丝 -C1010-C-A-+-镀黑锌-M2*4-H2 pcs 支架 1 pcs 防滑垫 塑壳 -支架-PC-黑色-V0-58.4*14*13-纹面-丝印-R 1 pcs 硅胶件-防滑垫-黑色-背胶-纹面-55.8*12*1-R 1 pcs 塑壳-导光柱-PC-透明-V0-25.7*24.8*2.3-纹面-R 线圈 塑壳 -面盖-PC-黑色-V0-70.5*126.7*5.3-纹面-丝印-R 面盖1 pcs LACC137无线充10W(Qi)直连USB-A 3FT黑色（无包材） LUZWC003-CS-R1 123 45 6 7 89101112 7 8 6 4 3 21 7 8 6 4 3 21 NOTES:(注解) 1. Appearance shall be inspected in accordance with the《AEQW-QA-012 Charger finished product inspection standard》 and the content should comply with drawing. with drawing. 外观依《AEQW-QA-012 Charger成品检验标准》检验、内容应符合图纸. 2.Mechanical Test(机械测试)： 2.1.Unit drop: falls freely on the cement floor at the height of 100cm, once each surface, 6 times, no cracking on enclosure, no electrical failure. 单体跌落:高度100cm自由跌落于水泥地板，每个面一次，跌落6次,外壳无开裂，电性正常 2.2. Tumbling test : 200 times from the height of 50 cm,15times/Min,After the test ,the housing has no crack and the electrical function keeps normal. 滚筒测试:高度50cm，200次，15次/min,外壳无开裂，电性正常 3.Environmental test(环境测试)： 3.1. Inner box or color box for high and low temperature storage: keep the temperature at -40°C for 23 minutes, and then keep it is 85°C for 23 minutes, go through 50 cycles, placed at room temperature for 1H, the product can work normally, and have no appearance defect such as enclosure melting. 内箱或彩盒高低温存储:环境温度-40°C/23分钟，温度85°C/23分钟，循环50个周期，常温放置 1H,产品通电可以正常工作及不允许出现外壳溶胶等外观不良。 3.2.High temperature and humidity: Temperature 85°C, humidity 85%, Use matching power input ,output no-load, work for 72H, the product can work normally. It is not allowed to have appearance defects such as enclosure melting. 高温高湿:温度85°C湿度85%，使用配套电源输入、输出空载，工作72H,产品通电可以正常工作 不允许现外壳溶胶等外观不良. 3.3.High low temperature work: Use matching power input, temperature range at -10°C~40°C, keep at hightemperature and low temperature each for 20min, total 36 cycles. 高低温工作:温度变化范围-10°C~40°C，使用配套电源输入、输出满载，高低温各保持20min， 共进行36个循环。 4. Foreign object detection: under the condition of Useing matching power input, the product will stop charging after the foreign object is placed in the wireless charging area 异物检测:使用配套电源输入条件下,无线充充电区域放入异物后，产品停止充电 5.Salt spray test: the sodium chloride solution with a concentration of 5% is automatically sprayed for 24 hours after the salt spray test, and the test is started after placed 4H at room temperature.After the test, clean it with clean water and let it dry naturally, there should be no corrosion, rust or other abnormal phenomena. 盐雾测试:5%浓度的氯化钠溶液,经盐雾试验自动喷雾24小时，室温放置4H后开始检测。测试完 成后使用清水清洗，自然晾干无腐蚀，生锈等异常现象 6.Anhydrous alcohol (concentration above 99.5%), wear-resisting testing machine, with pure cotton cloth dipped in anhydrous alcohol (wrapped on the test head,1cm²) , apply 500g load. After the test, slight wear and fading of the font is allowed, but the font content is required to be fully legible. 无水酒精（浓度99.5%以上），耐磨试验机，用纯棉布蘸满无水酒精（包在测试头上，包过后面 积约为1cm²），施加500g的载荷。试验30次完成后，允许字体有轻微的磨损及褪色，但要求字 体内容仍完整可辨认。 7. Enclosure temperature rise: under the condition of Useing matching power input, output with full load, ambient temperature of 25°C±3°C, non-enclosure temperature rise should be less than 50°C, metal enclosure temperature rise should be less th…

Text truncated - open the document above for the full version.

ASAP Technology (jiangxi) Co., Ltd TEST REPORT SCOPE OF WORK SAR Assessment– 080-08-4962 REPORT NUMBER 240506052SZN-002 ISSUE DATE [REVISED DATE] 25 June 2024 [--------------------] PAGES 4 DOCUMENT CONTROL NUMBER RF Exposure © 2017 INTERTEK TEST REPORT Intertek No.: 240506052SZN-002 This report is for the exclusive use of Intertek's Client and is provided pursuant to the agreement between Intertek and its Client. Intertek's responsibility and liability are limited to the terms and conditions of the agreement. Intertek assumes no liability to any party, other than to the Client in accordance with the agreement, for any loss, expense or damage occasioned by the use of this report. Only the Client is authorized to permit copying or distribution of this report and then only in its entirety. Any use of the Intertek name or one of its marks for the sale or advertisement of the tested material, product or service must first be approved in writing by Intertek. The observations and test results in this report are relevant only to the sample tested. This report by itself does not imply that the material, product, or service is or has ever been under an Intertek certification program. Intertek Testing Services Shenzhen Ltd. Longhua Branch 101, 201, Building B, No. 308 Wuhe Avenue, Zhangkengjing Community, GuanHu Subdistrict, LongHua District, ShenZhen. Tel: (86 755) 8601 6288 Fax: (86 755) 8601 6751 Version: 01-November-2017 Page 1 of 4 RF Exposure 101, 201, Building B, No. 308 Wuhe Avenue, Zhangkengjing Community, GuanHu Subdistrict, LongHua District, ShenZhen. Tel: (86 755) 8601 6288 Fax: (86 755) 8601 6751 www.intertek.com Test Report Applicant : ASAP Technology (jiangxi) Co., Ltd Ji’an Industrial Park, Ji’an, Jiangxi 343100 China Sample Description Product : Wireless charger Model No. : 080-08-4962 Brand Name : dealworthy Electrical Rating : Input: DC 5V 3A,9V 2A, 12V 1.5A Wireless Output: 10.0W Max Date Received : 06 May 2024 Date Test Conducted : 06 May 2024 to 25 June 2024 Test Requested : Test for compliance with CFR 47 part 1 Test Method : Environmental evaluation and exposure limit according to FCC CFR 47 part 1, 1.1307(c) and (d), 1.1310 KDB 680106 D01 RF Exposure Wireless Charging v04 Test Result : Pass Conclusion : When determining of test conclusion, measurement uncertainty of tests have been considered. ******************************** End of Page ******************************** Prepared and Checked By: Approved By: Tenet Cao Ryan Chen Assistant Engineer Senior Project Engineer Date: 25 June 2024 TEST REPORT Intertek No.: 240506052SZN-002 Version: 01-November-2017 Page 2 of 4 RF Exposure Test Report Test Setup Configuration Note - The RF exposure test is performed in the shield room. - The test distance is between the edge of the charger and the the measurement probe. - There are two coils, which coil will work depends on the placement of the mobile phone (vertical or horizontal). Both cases are tested, and only the worst patterns are shown in the report. Test Equipment List Equipment No. Equipment Manufacturer Model No. Cal. Date Due Date SZ186-06 The Magnetic Ampli tude and Gradient Probe System SPEAG MAGPy- 8D3D+E3D 2024-03-07 2025-03-07 Support Equipment List Description Manufacturer Detail Mobile phone Samsung (Provided by Intertek) Model: Samsung (SM-G9300) Adapter Quick Wall Charger (Provided by Client) Model: 080-08-4962 Input: 100-240Vac 50/60Hz 0.5A Output: 5Vdc 3A, 9Vdc 2A, 12Vdc 1.5A TEST REPORT Intertek No.: 240506052SZN-002 Version: 01-November-2017 Page 3 of 4 RF Exposure Reference Limit: Environmental evaluation and exposure limit according to FCC CFR 47 part 1, 1.1307(c) and (d), 1.1310 According to FCC 1.1310: The criteria listed in the following table shall be used to evaluate the environment impact of human exposure to radio frequency (RF) radiation. LIMITS FOR MAXIMUM PERMISSIBLE EXPOSURE (MPE) Frequency Range ( MHz ) Electric Field strength (V/m) Magnetic Field Strength (A/m) Power Density (mW/cm 2 ) Average Time (minutes) (A) Limits for Occupational/Controlled Exposure 0.3 – 3.0 614 1.63 (100) * 6 (B) Limits for General Population/Uncontrolled Exposure 0.3 – 1.34 614 1.63 (100) * 30 Note: * = Plane wave equivalent power density Test Result: Pass H-Field Strength at 20 cm surrounding the EUT Frequency Range (MHz) EUT Operation mode Probe Position Front (A/m) Probe Position Rear (A/m) Probe Position Left (A/m) Probe Position Right (A/m) Probe Position Top (A/m) Limits (A/m) 0.115- 0.205 1% Battery Level 0.05 0.05 0.05 0.07 0.14 1.63 0.115- 0.205 50% Battery Level 0.06 0.06 0.05 0.07 0.12 1.63 0.115- 0.205 99% Battery Level 0.05 0.06 0.04 0.06 0.13 1.63 0.115- 0.205 Stand-by 0.04 0.05 0.04 0.05 0.11 1.63 E-Field Strength at 20 cm surrounding the EUT Frequency Range (MHz) EUT Operation mode Probe Position Front (V/m) Probe Position Rear (V/m) Probe Position Left (V/m) Probe Position Right (V/m) Probe Position Top (V/m) Limits (V/m) 0.115- 0.205 1% Battery Level 4.33 2.97 3.93 4.47 6.62 614 0.115- 0.205 50% Battery Level 4.12 2.78 3.83 4.33 6.45 614 0.115- 0.205 99% Battery Level 4.19 2.91 3.87 4.42 6.33 614 0.115- 0.205 Stand-by 3.88 2.88 3.66 4.17 6.25 614 TEST REPORT Intertek No.: 240506052SZN-002 Version: 01-November-2017 Page 4 of 4 RF Exposure Configuration photo of the test: Please refer to RF Exposure setup photos. pdf. ****************************** End of Report******************************

ASAP Technology (jiangxi) Co., Ltd TEST REPORT SCOPE OF WORK FCC TESTING–080-08-4962 REPORT NUMBER 240506052SZN-001 ISSUE DATE [REVISED DATE] 14 June 2024 [---------------------] PAGES 20 DOCUMENT CONTROL NUMBER FCC ID 209_b © 2017 INTERTEK Intertek Report No.: 240506052SZN-001 This report is for the exclusive use of Intertek's Client and is provided pursuant to the agreement between Intertek and its Client. Intertek's responsibility and liability are limited to the terms and conditions of the agreement. Intertek assumes no liability to any party, other than to the Client in accordance with the agreement, for any loss, expense or damage occasioned by the use of this report. Only the Client is authorized to permit copying or distribution of this report and then only in its entirety. Any use of the Intertek name or one of its marks for the sale or advertisement of the tested material, product or service must first be approved in writing by Intertek. The observations and test results in this report are relevant only to the sample tested. This report by itself does not imply that the material, product, or service is or has ever been under an Intertek certification program. Intertek Testing Services Shenzhen Ltd. Longhua Branch 101, 201, Building B, No. 308 Wuhe Avenue, Zhangkengjing Community, GuanHu Subdistrict, LongHua District, ShenZhen. Tel: (86 755) 8601 6288 Fax: (86 755) 8601 6751 Version: 01-November-2017 Page: 1 of 20 FCC ID 209_b TEST REPORT 101, 201, Building B, No. 308 Wuhe Avenue, Zhangkengjing Community, GuanHu Subdistrict, LongHua District, ShenZhen. Tel: (86 755) 8601 6288 Fax: (86 755) 8601 6751 www.intertek.com ASAP Technology (jiangxi) Co., Ltd Application For Certification FCC ID: 2APXNLACC137 Wireless charger Model: 080-08-4962 Transmitter Report No.: 240506052SZN-001 We hereby certify that the sample of the above item is considered to comply with the requirements of FCC Part 15, Subpart C for Intentional Radiator, mention 47 CFR [10-1-23] Prepared and Checked by: Approved by: Tenet Cao Ryan Chen Assistant Engineer Sr. Project Engineer Date: 14 June 2024 Intertek Report No.: 240506052SZN-001 Version: 01-November-2017 Page: 2 of 20 FCC ID 209_b TEST REPORT MEASUREMENT/TECHNICAL REPORT This report concerns (check one) Original Grant X Class II Change Equipment Type: DCD - Part 15 Low Power Transmitter Below 1705 kHz Deferred grant requested per 47 CFR 0.457(d)(1)(ii)? Yes No X If yes, defer until : date Company Name agrees to notify the Commission by: date of the intended date of announcement of the product so that the grant can be issued on that date. Transition Rules Request per 15.37? Yes No X If no, assumed Part 15, Subpart C for intentional radiator - the new 47 CFR [10-01- 23] Edition] provision. Report prepared by: Tenet Cao Intertek Testing Services Shenzhen Ltd. Longhua Branch 101, 201, Building B, No. 308 Wuhe Avenue, Zhangkengjing Community, GuanHu Subdistrict, LongHua District, ShenZhen. Tel: (86 755) 8614 0743 Fax: (86 755) 8601 6751 Intertek Report No.: 240506052SZN-001 Version: 01-November-2017 Page: 3 of 20 FCC ID 209_b TEST REPORT Table of Contents 1.0 Summary of Test Results .......................................................................................... 4 2.0 General Description ................................................................................................. 5 2.1 Product Description .............................................................................................. 5 2.2 Related Submittal(s) Grants ................................................................................... 5 2.3 Test Methodology ................................................................................................ 5 2.4 Test Facility ......................................................................................................... 5 3.0 System Test Configuration ........................................................................................ 6 3.1 Justification ......................................................................................................... 6 3.2 EUT Exercising Software ........................................................................................ 6 3.3 Special Accessories ............................................................................................... 6 3.4 Equipment Modification ........................................................................................ 6 3.5 Measurement Uncertainty .................................................................................... 7 3.6 Support Equipment List and Description ................................................................ 7 4.0 Measurement Results .............................................................................................. 8 4.1 Field Strength Calculation ...................................................................................... 8 4.2 Radiated Emission Configuration Photograph ........................................................... 9 4.3 Radiated Spurious Emission ................................................................................... 9 4.4 Conducted Emission Configuration Photograph ...................................................... 13 4.5 Conducted Emission ........................................................................................... 13 5.0 Equipment Photographs ........................................................................................ 16 6.0 Product Labelling .................................................................................................. 16 7.0 Technical Specifications ......................................................................................... 16 8.0 Instruction Manual ................................................................................................ 16 9.0 Miscellaneous Information ..................................................................................... 17 9.1 2…

Text truncated - open the document above for the full version.