2AQ68T99W175M5G WWAN Module

Federal Communication Commission Interference Statement This device complies with Part 15 of the FCC Rules. Operation is subject to the following two conditions: (1) This device may not cause harmful interference, and (2) this device must accept any interference received, including interference that may cause undesired operation. This equipment has been tested and found to comply with the limits for a Class B digital device, pursuant to Part 15 of the FCC Rules. These limits are designed to provide reasonable protection against harmful interference in a residential installation. This equipment generates, uses and can radiate radio frequency energy and, if not installed and used in accordance with the instructions, may cause harmful interference to radio communications. However, there is no guarantee that interference will not occur in a particular installation. If this equipment does cause harmful interference to radio or television reception, which can be determined by turning the equipment off and on, the user is encouraged to try to correct the interference by one of the following measures: - Reorient or relocate the receiving antenna. - Increase the separation between the equipment and receiver. - Connect the equipment into an outlet on a circuit different from that to which the receiver is connected. - Consult the dealer or an experienced radio/TV technician for help. FCC Caution: Any changes or modifications not expressly approved by the party responsible for compliance could void the user's authority to operate this equipment. This transmitter must not be co-located or operating in conjunction with any other antenna or transmitter. Radiation Exposure Statement: This equipment complies with FCC radiation exposure limits set forth for an uncontrolled environment. This equipment should be installed and operated with minimum distance 20cm between the radiator & your body. This module is intended for OEM integrators only. Per FCC KDB 996369 D03 OEM Manual v01 guidance, the following conditions must be strictly followed when using this certified module: KDB 996369 D03 OEM Manual v01 rule sections: 2.2 List of applicable FCC rules This module has been tested for compliance to FCC Part 22, 24, 27, 90, 96. 2.3 Summarize the specific operational use conditions The module is tested for standalone mobile RF exposure use condition. Any other usage conditions such as co-location with other transmitter(s) or being used in a portable condition will need a separate reassessment through a class II permissive change application or new certification. 2.4 Limited module procedures Not applicable. 2.5 Trace antenna designs Not applicable. 2.6 RF exposure considerations This equipment complies with FCC mobile radiation exposure limits set forth for an uncontrolled environment. This equipment should be installed and operated with a minimum distance of 20cm between the radiator & your body. If the module is installed in a portable host, a separate SAR evaluation is required to confirm compliance with relevant FCC portable RF exposure rules. 2.7 Antennas The following antennas have been certified for use with this module; antennas of the same type with equal or lower gain may also be used with this module. The antenna must be installed such that 20 cm can be maintained between the antenna and users. Antenna Type PCB, Monopole, PIFA Antenna connector I-PEX 2.8 Label and compliance information The final end product must be labeled in a visible area with the following: “Contains FCC ID: 2AQ68T99W175M”. The grantee's FCC ID can be used only when all FCC compliance requirements are met. 2.9 Information on test modes and additional testing requirements This transmitter is tested in a standalone mobile RF exposure condition and any co-located or simultaneous transmission with other transmitter(s) or portable use will require a separate class II permissive change re-evaluation or new certification. 2.10 Additional testing, Part 15 Subpart B disclaimer This transmitter module is tested as a subsystem and its certification does not cover the FCC Part 15 Subpart B (unintentional radiator) rule requirement applicable to the final host. The final host will still need to be reassessed for compliance to this portion of rule requirements if applicable. As long as all conditions above are met, further transmitter test will not be required. However, the OEM integrator is still responsible for testing their end-product for any additional compliance requirements required with this module installed. IMPORTANT NOTE: In the event that these conditions can not be met (for example certain laptop configurations or co-location with another transmitter), then the FCC authorization is no longer considered valid and the FCC ID can not be used on the final product. In these circumstances, the OEM integrator will be responsible for re-evaluating the end product (including the transmitter) and obtaining a separate FCC authorization. Manual Information To the End User The OEM integrator has to be aware not to provide information to the end user regarding how to install or remove this RF module in the user’s manual of the end product which integrates this module. The end user manual shall include all required regulatory information/warning as show in this manual. OEM/Host manufacturer responsibilities OEM/Host manufacturers are ultimately responsible for the compliance of the Host and Module. The final product must be reassessed against all the essential requirements of the FCC rule such as FCC Part 15 Subpart B before it can be placed on the US market. This includes reassessing the transmitter module for compliance with the Radio and EMF essential requirements of the FCC rules. This module must not be incorporated into any other device or system without retesting for compliance as multi-radio and combined equipment Industry Canada statement: This device complies with ISED’s licence-exempt RSSs. Operation is subject to the following two con…

Text truncated - open the document above for the full version.

COMPANY CONFIDENTIAL - 1 - 5GNR/ LTE-Advanced PCI Express M.2 Module (Sub 6G, LTE, UMTS) Engineering Requirements Specification Project code: T99W175M Solution: SDX55+SDR865+PMX55 SKU: WW-1-5G Foxconn PN Customer PN T99W175.06 K1YCW T99W175.08 JP18Y T99W175.09 FTY9X T99W175.30 1TFY5 T99W175.31 H75GC T99W175.32 01PCT Copyright © 2020. Foxconn Communications Inc. All rights reserved. COMPANY CONFIDENTIAL - 2 - Reviewers Department Name Signature Review Dates * Plan ** Results Project Manager Ai-Ning Song Project Leader Michael. Xiao Hardware Engineer Lynn. Liu COMPANY CONFIDENTIAL - 3 - Modification History Rev Date Originator Comment R1.0 2019/5/9 Lynn. Liu Initial release R1.1 2019/5/20 Lynn. Liu Update base on the customer requirements R1.2 2019/5/28 Lynn. Liu Update item 2.4 for antenna requirements; item 1.4.2 for USIM2 R1.3 2019/5/30 Lynn. Liu Update Pin38/60 description and item 1.5.12 for Coexistence R1.4 2019/7/9 Lynn. Liu 1. Remove n25/38/40& B43 support due to Qualcomm update (item1.1); 2. Remove n71& GPS L5 due to not in POR and B48 as TBD; 3. Update mmWave IF connector pin definition (item 2.4.2); 4. Update ME drawing (item3.2 R1.5 2019/7/25 Lynn. Liu 1. Update PCIe connection guideline(item1.5.4); 2. Update ME drawing (item3.2); 3. Update antenna configuration (item 2.4.2); 4. Update LTE Rx sensitivity Spec; 5. Update W_Disable# (item1.5.5) R1.6 2019/9/12 Lynn. Liu 1. Update Pin29/31/35/37(USB3.0) to NC; 2. Need Platform side reserve USB2.0 for factory test (WinPE) (item1.4.2) R1.7 2019/10/08 Lynn. Liu 1. Disable B48 for NA (item 1); 2. Update operating temperature (item 4.1); 3. Update antenna configuration (item 2.4.2 Figure2-2); 4. Update golden plating drawing; 5. Pin29/31/35/37 as NC and reserve with PCIe Lane 2 R1.8 2020/2/24 Lynn. Liu 1. Remove mmW for Sub6G only SKU; 2. Enable B48 for US& EU 3. Remove Reset (Pin67) requirement; 4. Update antenna configure (Item 2.4.2 Figure2-2); 5. Update HW feature (Item 2); 6. Update initial power consumption Spec (Item 4.2); 7. Update RF performance Spec (Item 5.1& 5.2) & support bandwidth; 8. Add DPS feature R1.9 2020/3/27 Lynn. Liu 1. Add PN for Olympic MLK& Andrews; 2. Disable B40 to meet FCC requirement; 3. Update Power on/off sequence requirement (Item 1.5.13); 4. Reserve 0.1uF on Pin6(Full card power off) & Pin50 (PERST#) Item 1.5.3& 1.5.4; 5. Add n71 for new Platform POR COMPANY CONFIDENTIAL - 4 - CONTENTS 1. GENERAL DESCRIPTION ............................................................... 5 1.1 SYSTEM MAIN FEATURE ............................................................... 6 1.2 EUTRA -NR- DUAL CONNECTIVITY & CARRIER AGGREGATION COMBINATION .............................................................. 10 1.3 HOST INTEGRATION INSTRUCTIONS ...................................... 13 1.4 ANTENNA INFORMATION ...................... 錯誤! 尚未定義書籤。 1.5 HOST PRODUCT TESTING GUIDANCE ................................... 14 COMPANY CONFIDENTIAL 5 1. General Description T99W175M is designed to enable wireless data connectivity for notebook computer or any other device compatible with the PCI Express M.2 Specification 3042 type Key B slot. T99W175M is the data card solution that delivers wireless wide-area network (WWAN) connectivity for the 5GNR (Sub 6G), LTE, UMTS (HSDPA/HSUPA/HSPA+DC-HSPA+) and GPS/Glonass/ Beidou/ Galileo protocols in one hardware configuration. SKU WW-1-5G / T99W175M Carrier Support NA: AT&T, Verizon, Sprint WW: Vodafone, Telefonica-O2 APAC: Telstra, Docomo, KDDI, Softbank * Carrier engagement based on real business agreement QCT Solution SDX55+SDR865+SMR526+PMX55 5G FR1 (Sub 6G) LB: n5/8/12/20/28/71; MB: n1/2/3/66; HB: n7/38/41/77/78/79 FR2 (mmWave) NA 4x4 MIMO n1/2/3/66/7/38/41/77/78/79 UE Capability UL (TBD); DL(TBD) 4G Support Band LB: B26(5/18/19)/8/12(17)/13/14/20/28/29/71 MB: B1/2(25)/3/4(66)/32 HB: B7/30/34/38/39/40(Disable for FCC)/41/42/48 4x4 MIMO B1/25(2)/3/66(4)/7/30/40/41(38)/42/48 LAA B46 (DL only) LTE Cat. ue-CategoryUL 13 (UL: 150Mbps) + ue-CategoryDL 20 (DL: 2Gbps); 7xDL CA, 2xUL CA (Intra-band), 5xDL CA+4X4 MIMO (Up to Cat20) 3G WCDMA HSPA+ Rel8 (DL/UL: up to 42/11 Mbps) Support Band B1/2/4/5(6/19)/8/9 GNSS Dual-Frequency GNSS: L1 GPS/Glonass/Beidou/Galileo, USIM Dual SIM interface, Dual SIM Single Active (DSSA) eSIM eSIM Dual SIM with eSIM on board (eSIM is option), Dual SIM Single Active (DSSA) Interface PCIe3.0; Reserve USB2.0 for factory test (WinPE) Form factor 3042 PCIe M.2 Key.B COMPANY CONFIDENTIAL 6 1.1 System Main Feature Feature Description Physical PCI express M.2 module, size 3042, Key.B,75Pin golden finger Electrical Single VCC supply (3.135V~3.63V) Dimension Dimensions (L × W × H): 42 mm × 30 mm × 2.5 mm, maximum height=2.6mm (add PCB tolerance=0.1mm) Shielding design Shield case on board design, no additional shielding requirement Weight Approximately ~8g USIM Off-board USIM connector supported on Host through USIM1/ USIM2 Operating Bands WCDMA/HSDPA/HSUPA/HSPA+ operating bands: Band 1: 1920 to 1980 MHz (UL), 2110 to 2170 MHz (DL) Band 2: 1850 to 1910 MHz (UL), 1930 to 1990 MHz (DL) Band 4: 1710 to 1755 MHz (UL), 2110 to 2155 MHz (DL) Band 5: 824 to 849 MHz (UL), 869 to 894 MHz (DL) Band 6: 830 to 840 MHz (UL), 875 to 885 MHz (DL) Band 8: 880 to 915 MHz (UL), 925 to 960 MHz (DL) Band 9: 1750 to 1785 MHz (UL), 1845to 1880 MHz (DL) Band 19: 830 to 845 MHz (UL), 875 to 890 MHz (DL) LTE FDD/TDD operating bands: Band 1: 1920 to 1980 MHz (UL), 2110 to 2170 MHz (DL) Band 2: 1850 to 1910 MHz (UL), 1930 to 1990 MHz (DL) Band 3: 1710 to 1785 MHz (UL), 1805 to 1880 MHz (DL) Band 4: 1710 to 1755 MHz (UL), 2110 to 2155 MHz (DL) Band 5: 824 to 849 MHz (UL), 869 to 894 MHz (DL) Band 7: 2500 to 2570 MHz (UL), 2620 to 2690 MHz (DL) Band 8: 880 to 915 MHz (UL), 925 to 960 MHz (DL) Band 12: 699 to 716 MHz (UL), 729 to 746 MHz (DL) Band 13: 777 to 787 MHz (UL), 746 to 756 MHz (DL) Band 14: 788 to 798 MHz (UL), 758 to 768 MHz (DL) Band 17: 704 to 716 MHz (UL), 734 to 746 MHz (DL) Band 18: 815 to 830…

Text truncated - open the document above for the full version.

Hon Lin Technology Co., Ltd. 11F, No.32, Jihu Rd., Neihu Dist., Taipei City 114, Taiwan R.O.C. AGENCY AUTHORIZATION LETTER Date: 2020/09/06 FCC ID: 2AQ68T99W175M To whom it may concern: We, the undersigned, hereby authorize Amanda Wu of Bureau Veritas Consumer Products Services (H.K.) Ltd., Taoyuan Branch (BV CPS Taoyuan) of Taiwan to act on our behalf in all manners relating to FCC application for equipment authorization, including signing of all documents relating to these matters. Any and all acts carried out by Amanda Wu of BV CPS Taoyuan on our behalf shall have the same effect as acts of our own. If you have any questions regarding the authorization, please don’t hesitate to contact us. Sincerely yours, Signature: Nancy Lin / Assistant Manager Hon Lin Technology Co., Ltd. TEL:(02) 22656711 FAX: (02) 22656512 E-mail: [email protected]

Hon Lin Technology Co., Ltd. 11F, No.32, Jihu Rd., Neihu Dist., Taipei City 114, Taiwan R.O.C. Federal Communications Commission Authorization and Evaluation Division Date: September 6, 2020 Confidentiality Request FCC ID: 2AQ68T99W175M Pursuant to Sections 0.457 and 0.459 of the commission’s rules, we request short-term confidential treatment for the following information until 180days after the Grant Date of Equipment Authorization in order to ensure sensitive business information remains confidential until the actual marketing of the device: External photos Internal Photos Test Setup photos User’s manual Thank you! Sincerely yours, ------------------------------------------------------- Nancy Lin / Assistant Manager Hon Lin Technology Co., Ltd. TEL:(02) 22656711 FAX: (02) 22656512 E-mail: [email protected]

Hon Lin Technology Co., Ltd. 11F, No.32, Jihu Rd., Neihu Dist., Taipei City 114, Taiwan R.O.C. Date: 2020/09/06 FCC ID: 2AQ68T99W175M Federal Communications Commission Authorization and Evaluation Division Confidentiality Request Pursuant to Sections 0.457 and 0.459 of the Commission’s Rules, the Applicant hereby requests confidential treatment of information accompanying this Application as outlined below: Schematics Block Diagram Tune-up procedure Operational description Parts list The above materials contain trade secrets and proprietary information not customarily released to the public. The public disclosure of these matters might be harmful to the Applicant and provide unjustified benefits to its competitors. The Applicant understands that pursuant to Rule 0.457, disclosure of this Application and all accompanying documentation will not be made before the date of the Grant for this application. Sincerely yours, Nancy Lin / Assistant Manager Hon Lin Technology Co., Ltd. TEL:(02) 22656711 FAX: (02) 22656512 E-mail: [email protected]

FCC ID: 2AQ68T99W175M Modular Approval Request Letter Bureau Veritas Consumer Products Services (H.K.) Ltd., Taoyuan Branch September 15, 2020 Dear Application Examiner, Hon Lin Technology Co., Ltd., 5G WWAN Module, FCC ID: 2AQ68T99W175M would like to have your authorization as a modular approval specific to the mobile RF exposure condition. The requirements of KDB996369 have been met and shown on the following statements. 1. “The modular transmitter must have its own RF shielding.” The radio portion of this module has been shielded, please see exhibition External Photo. 2. “The modular transmitter must have buffered modulation/data inputs.” The EUT has buffered data inputs, it is integrated in chip SDX55, SDR865, SMR526. 3. “The modular transmitter must have its own power supply regulation.” The part number of this regulator is PMX55. 4. “The modular transmitter must comply with the antenna requirements of section 15.203 and 15.204(C).” The EUT meets the FCC antenna requirements. The spurious emission, unique antenna connector and photo of antennas are shown in the test report. 5. “The modular transmitter must be tested in a stand-alone configuration” The EUT was tested in a stand-alone configuration via a USB extender fixture. Please see section Photographs of Test Configuration in the test report, the EUT was plugged in this extender. 6. “The modular transmitter must be labeled with its own FCC ID number.” Please see exhibition Label Sample for the FCC ID of this module. And also in the exhibition Users Manual, there are instructions give to the OEM on how to label the end product. FCC ID: 2AQ68T99W175M 7. “The modular transmitter must comply with any specific rule or operating requirements applicable to the transmitter and the manufacturer must provide adequate instructions along with the module to explain any such requirements.” The EUT is compliant with all applicable FCC rules. Detail instructions for maintaining compliance are given in the Users Manual. 8. “The modular transmitter must comply with any applicable RF exposure requirements.” The EUT is compliant with all applicable RF exposure requirements. RF Exposure is addressed in the RF exposure exhibition. Please contact me if you have any further questions. Thanks for your attention. Best Regards, Amanda Wu / Senior Specialist Bureau Veritas Consumer Products Services (H.K.) Ltd., Taoyuan Branch Tel: 886-3-318 3232 ext. 1929 Fax: 886-3-327 0892 Email: [email protected]

Hon Lin Technology Co., Ltd. 11F, No.32, Jihu Rd., Neihu Dist., Taipei City 114, Taiwan R.O.C. Date: September 14, 2020 Attestation FCC ID: 2AQ68T99W175M To Whom It May Concern: This application is intended to reuse previous test data (from FCC ID: 2AQ68T99W175, certified on 05/07/2020 of initial application and 06/04/2020 of C2PC application), due to the fact that the two versions of products are hardware-wise identical and only the following changes have been made: 1. Adding 5GNR mmWave components but not enable. Since the 5GNR mmWave components no big impact on the emission is expected. So, we have performed spot checks on the following items to verify that if any unexpected RF conducted power or emission changes can be noted. The test results show that all spot check data are within the instrument measurement uncertainty and data reuse is justifiable. Verification test items with 1 samples:  Conducted Power and ERP/EIRP full test on all modulations and channels  Radiated Emission Test (choose worse case) For the test result, please refers to included exhibit “Test Reports.pdf” for detail. Reuse data test items (Part 22/24/27/90/96)  Conducted Power / EIRP/ ERP / PAPR / OBW / Modulation characteristics / Frequency stability  Radiated Emission / Conducted emission / Band edge  SAS protocol (Part 96.47 End user device additional requirements), the software remain the same. Hon Lin Technology Co., Ltd. 11F, No.32, Jihu Rd., Neihu Dist., Taipei City 114, Taiwan R.O.C. Date: September 14, 2020 Also, both the referenced application and this new application are all subject to the same FCC rule and there is no new rule update for related rules. Accordingly, we believe that the reuse data from previous certified filing is justifiable. Thank you for your attention and please feel free to contact us, if you should have any questions. Sincerely yours, Nancy Lin / Assistant Manager Hon Lin Technology Co., Ltd. TEL:(02) 22656711 FAX: (02) 22656512 E-mail: [email protected]

Reference No.: 200529E02-1 Page 1/ 23 CONSTRUCTION PHOTOS OF EUT EUT with HW 1 Reference No.: 200529E02-1 Page 2/ 23 EUT with HW 2 Reference No.: 200529E02-1 Page 3/ 23 EUT with HW 3 Reference No.: 200529E02-1 Page 4/ 23 EUT with HW 4 Reference No.: 200529E02-1 Page 5/ 23 Antenna No. 1 Reference No.: 200529E02-1 Page 6/ 23 Antenna No. 2 Reference No.: 200529E02-1 Page 7/ 23 Antenna No. 3 Reference No.: 200529E02-1 Page 8/ 23 Antenna No. 4 Reference No.: 200529E02-1 Page 9/ 23 Antenna No. 5 Reference No.: 200529E02-1 Page 10/ 23 Antenna No. 6 Reference No.: 200529E02-1 Page 11/ 23 Antenna No. 7 Reference No.: 200529E02-1 Page 12/ 23 Antenna No. 8 Reference No.: 200529E02-1 Page 13/ 23 Antenna No. 9 Reference No.: 200529E02-1 Page 14/ 23 Antenna No. 10 Reference No.: 200529E02-1 Page 15/ 23 Antenna No. 11 Reference No.: 200529E02-1 Page 16/ 23 Antenna No. 12 Reference No.: 200529E02-1 Page 17/ 23 Antenna No. 13 (Tx1/Rx1, Tx2/Rx3) Tx2/Rx3 -MIMO2 Tx1/Rx1 -Main Tx1/Rx1 -Main Tx2/Rx3 -MIMO2 Reference No.: 200529E02-1 Page 18/ 23 Antenna No. 13 (Rx2) Rx2-Aux Rx2-Aux Reference No.: 200529E02-1 Page 19/ 23 Antenna No. 13 (Rx4) Rx4-MIMO3 Rx4-MIMO3 Reference No.: 200529E02-1 Page 20/ 23 Antenna No. 14 (Ant. 0) Reference No.: 200529E02-1 Page 21/ 23 Antenna No. 14 (Ant. 1) Reference No.: 200529E02-1 Page 22/ 23 Antenna No. 14 (Ant. 2) Reference No.: 200529E02-1 Page 23/ 23 Antenna No. 14 (Ant. 3)

WWAN Lenovo PN: SW10T06443 IMEI: xxxxxxxxyyyyyyz DVT2 Engineering sample not for MP Foxconn PN: T99W175.01 MO: 1234567890-VVSS Made In China 8SSW10T06443F1NNYMD0001 EC: 3282397 FCC ID: 2AQ68T99W175M CMIIT ID: 2019CPXXXX R-C-Fii-T99W175 XXX-XXXXXX XXXXXXXXXX IC: 24374-T99W175M Foxconn Model: T99W175M : XXXXX : T99W175, : : : 3.3V 2.5A

Reference No.: 200529E02-2 Page 1/ 4 CONSTRUCTION PHOTOS OF EUT EUT with HW 1 Reference No.: 200529E02-2 Page 2/ 4 EUT with HW 2 Reference No.: 200529E02-2 Page 3/ 4 EUT with HW 3 Reference No.: 200529E02-2 Page 4/ 4 EUT with HW 4

Report No.: SA200109E02B Page No. 1 / 9 Report Format Version: 6.1.1 Reference No.: 200519E11 FCC RF Exposure Report Report No.: SA200109E02B FCC ID: 2AQ68T99W175 Test Model: T99W175 Received Date: Jan. 10, 2020 Test Date: Feb. 26 ~ May 28, 2020 Issued Date: May 29, 2020 Applicant: Hon Lin Technology Co., Ltd. Address: 11F, No. 32, Jihu Rd., Neihu Dist., Taipei City 114, Taiwan R.O.C. Issued By: Bureau Veritas Consumer Products Services (H.K.) Ltd., Taoyuan Branch Lin Kou Laboratories Lab Address: No. 47-2, 14th Ling, Chia Pau Vil., Lin Kou Dist., New Taipei City, Taiwan Test Location: No. 19, Hwa Ya 2nd Rd., Wen Hwa Vil., Kwei Shan Dist., Taoyuan City 33383, Taiwan FCC Registration / Designation Number: 788550 / TW0003 This report is for your exclusive use. Any copying or replication of this report to or for any other person or entity, or use of our name or trademark, is permitted only with our prior written permission. This report sets forth our findings solely with respect to the test samples identified herein. The results set forth in this report are not indicative or representative of the quality or characteristics of the lot from which a test sample was taken or any similar or identical product unless specifically and expressly noted. Our report includes all of the tests requested by you and the results thereof based upon the information that you provided to us. You have 60 days from date of issuance of this report to notify us of any material error or omission caused by our negligence, provided, however, that such notice shall be in writing and shall specifically address the issue you wish to raise. A failure to raise such issue within the prescribed time shall constitute your unqualified acceptance of the completeness of this report, the tests conducted and the correctness of the report contents. Unless specific mention, the uncertainty of measurement has been explicitly taken into account to declare the compliance or non-compliance to the specification. The report must not be used by the client to claim product certification, approval, or endorsement by TAF or any government agencies. Report No.: SA200109E02B Page No. 2 / 9 Report Format Version: 6.1.1 Reference No.: 200519E11 Table of Contents Release Control Record .................................................................................................................................. 3 1 Certificate of Conformity ...................................................................................................................... 4 2 RF Exposure .......................................................................................................................................... 5 3.1 Limits for Maximum Permissible Exposure (MPE) .............................................................................. 5 3.2 MPE Calculation Formula ................................................................................................................... 5 3.3 Classification ....................................................................................................................................... 5 3 Calculation Result of Maximum Density Power ................................................................................ 6 Report No.: SA200109E02B Page No. 3 / 9 Report Format Version: 6.1.1 Reference No.: 200519E11 Release Control Record Issue No. Description Date Issued SA200109E02B Original release May 29, 2020 Report No.: SA200109E02B Page No. 4 / 9 Report Format Version: 6.1.1 Reference No.: 200519E11 1 Certificate of Conformity Product: 5G WWAN Module Brand: Foxconn Test Model: T99W175 Sample Status: Engineering Sample Applicant: Hon Lin Technology Co., Ltd. Test Date: Feb. 26 ~ May 28, 2020 Standards: FCC Part 2 (Section 2.1091) References Test Guidance: KDB 447498 D01 General RF Exposure Guidance v06 IEEE C95.3 -2002 The above equipment has been tested by Bureau Veritas Consumer Products Services (H.K.) Ltd., Taoyuan Branch, and found compliance with the requirement of the above standards. The test record, data evaluation & Equipment Under Test (EUT) configurations represented herein are true and accurate accounts of the measurements of the sample’s RF characteristics under the conditions specified in this report. Prepared by : , Date:May 29, 2020 Pettie Chen / Senior Specialist Approved by : , Date:May 29, 2020 Bruce Chen / Senior Project Engineer Report No.: SA200109E02B Page No. 5 / 9 Report Format Version: 6.1.1 Reference No.: 200519E11 2 RF Exposure 3.1 Limits for Maximum Permissible Exposure (MPE) Frequency Range (MHz) Electric Field Strength (V/m) Magnetic Field Strength (A/m) Power Density (mW/cm 2 ) Average Time (minutes) Limits For General Population / Uncontrolled Exposure 0.3-1.34 614 1.63 (100)* 30 1.34-30 824/f 2.19/f (180/f 2 )* 30 30-300 27.5 0.073 0.2 30 300-1500 ... ... f/1500 30 1500-100,000 ... ... 1.0 30 f = Frequency in MHz; *Plane-wave equivalent power density 3.2 MPE Calculation Formula Pd = (Pout*G) / (4*pi*r 2 ) where Pd = power density in mW/cm 2 Pout = output power to antenna in mW G = gain of antenna in linear scale pi = 3.1416 r = distance between observation point and center of the radiator in cm 3.3 Classification The antenna of this product, under normal use condition, is at least 20cm away from the body of the user. So, this device is classified as Mobile Device. Report No.: SA200109E02B Page No. 6 / 9 Report Format Version: 6.1.1 Reference No.: 200519E11 3 Calculation Result of Maximum Density Power Function Frequency Band (MHz) EIRP (dBm) Distance (cm) Power Density (mW/cm 2 ) Limit (mW/cm 2 ) WCDMA Band 2 1850.7-1909.3 27.79 20 0.120 1 WCDMA Band 4 1710.7-1754.3 27.74 20 0.118 1 LTE Band 2 1850.7-1909.3 28.09 20 0.128 1 LTE Band 4 1710.7-1754.3 28.25 20 0.133 1 LTE Band 7 2502.5-2567.5 28.66 20 0.146 1 LTE Band 25 1850.7-1914.3 27.99 20 0.125 1 LTE Band 30 2307.5-2312.5 23.50 20 0.045 1 LTE Band 38 2572.5-2617.5 28.85 20 0.153 1 LTE Band 41 2547.5-2652.5 32.03 …

Text truncated - open the document above for the full version.

Report No.: SA200109E02E Page No. 1 / 9 Report Format Version: 6.1.1 Reference No.: 200529E02 FCC RF Exposure Report Report No.: SA200109E02E FCC ID: 2AQ68T99W175M Original FCC ID: 2AQ68T99W175 Test Model: T99W175M Received Date: Jan. 10, 2020 Test Date: Feb. 26 ~ May 28, 2020 Issued Date: Aug. 11, 2020 Applicant: Hon Lin Technology Co., Ltd. Address: 11F, No. 32, Jihu Rd., Neihu Dist., Taipei City 114, Taiwan R.O.C. Issued By: Bureau Veritas Consumer Products Services (H.K.) Ltd., Taoyuan Branch Lin Kou Laboratories Lab Address: No. 47-2, 14th Ling, Chia Pau Vil., Lin Kou Dist., New Taipei City, Taiwan Test Location: No. 19, Hwa Ya 2nd Rd., Wen Hwa Vil., Kwei Shan Dist., Taoyuan City 33383, Taiwan FCC Registration / Designation Number: 788550 / TW0003 This report is for your exclusive use. Any copying or replication of this report to or for any other person or entity, or use of our name or trademark, is permitted only with our prior written permission. This report sets forth our findings solely with respect to the test samples identified herein. The results set forth in this report are not indicative or representative of the quality or characteristics of the lot from which a test sample was taken or any similar or identical product unless specifically and expressly noted. Our report includes all of the tests requested by you and the results thereof based upon the information that you provided to us. You have 60 days from date of issuance of this report to notify us of any material error or omission caused by our negligence, provided, however, that such notice shall be in writing and shall specifically address the issue you wish to raise. A failure to raise such issue within the prescribed time shall constitute your unqualified acceptance of the completeness of this report, the tests conducted and the correctness of the report contents. Unless specific mention, the uncertainty of measurement has been explicitly taken into account to declare the compliance or non-compliance to the specification. Report No.: SA200109E02E Page No. 2 / 9 Report Format Version: 6.1.1 Reference No.: 200529E02 Table of Contents Release Control Record .................................................................................................................................. 3 1 Certificate of Conformity ...................................................................................................................... 4 2 RF Exposure .......................................................................................................................................... 5 3.1 Limits for Maximum Permissible Exposure (MPE) .............................................................................. 5 3.2 MPE Calculation Formula ........................................…

Text truncated - open the document above for the full version.