2AS8AB72TBlood Pressure Monitor

Model Number: B72T USER’S MANUAL Blood Pressure Monitor Shanghai International Holding Corp. GmbH (Europe) Eiffestrasse 80, 20537 Hamburg, Germany. Version Number:1.0 Issue Date: 2024-01-12 Shenzhen Jamr Technology Co., Ltd. A101-301, D101-201, Jamr Science & Technology Park, No. 2 Guiyuan Road, Guixiang Community, Guanlan Street, Longhua District, 518100 Shenzhen, PEOPLE'S REPUBLIC OF CHINA 1 1.Introduction and Intended Use............................................................ 2.Important Information on Blood Pressure and its Measurement....... 3. Components of Your Blood Pressure Monitor................................... 4. Using Your Monitor for the First Time................................................ 5.Measurement Procedure...................................................................... 6.Care and Maintenance.......................................................................... 7. Warranty/service.................................................................................. 8. Certifications........................................................................................ 9. Technical Specifications..................................................................... 10. EMC Declaration................................................................................ 2 5 6 8 11 18 19 19 20 21 CONTENTS 2 1.Introduction and Intended Use The device is a fully automatic digital blood pressure measuring device. It is intended to measure systolic and diastolic blood pressure as well as the pulse for adults that ages are more than 12 years old by wrapping around the upper arm with cuff circumference ranging from 22cm to 42cm.The device can be used in medical facilities or at home, and only for indoor use. Contraindication: The device is not used for patients under dialysis therapy or on anticoagulant, antiplatelets, or steroids. Before using, please read this instruction manual carefully and then keep it in a safe place. 1.1 Remember... • Only a health-care professional is qualified to interpret blood pressure measurements. • This device is NOT intended to replace regular medical checkups. • Blood pressure readings obtained by this device should be verified before prescribing or making adjustments to any medications used to control hypertension. Under no circumstances should YOU alter the dosages of any drugs privately unless you have the permission of physician. • The device is intended for use by adults only and not intended for use on children and pregnant patient. •In cases of irregular heartbeat , measurements made with this instrument should only be evaluated after consultation with a physician. • The products, including accessories, shall be processed in accordance with local regulations after reaching the life cycle. • Any serious incident that has occurred in relation to the device should be reported to the manufacturer and the competent authority of the Member State in which the user and/or patient is established. 3 Warning: The use of other accessories other than those specified or provided by the equipment manufacturer may cause electromagnetic radiation to increase or decrease electromagnetic immunity resulting in operational failure. Warning: This system may fail to yield specified measurement accuracy if operated or stored in temperature or humidity conditions outside the limits stated in the specifications section of this manual. Warning: Do not use the AC adapter if the unit or the power cord is damaged. Turn off the power and unplug the power cord immediately. Warning: The user must check that the equipment functions safely and see that it is in proper working condition before being used. Warning: The device is not suitable for use in the presence of flammable anesthetic mixtures with air or with oxygen or nitrous oxide. Warning: If the patient is an intended operator, the functions of monitoring blood pressure and pulse rate can be safely used by patient. The routine clean and changing batteries can be performed by the patient. Warning: This device can not be used together with hf surgical equipment. Warning: The device provides a DC input port connected to external ac adapter. It is recommended that use the adapter specified by the manufacturer. The adapter should meet the following conditions: class II equipment, output voltage: DC 5V, current: ≥1A, and comply with IEC 60950, IEC 60601-1 or IEC 62368-1, provide at least two MOOP insulation between ac input and dc output. External adapter connected to medical electrical equipment through the DC input port must comply with the respective IEC or ISO standards (e.g. IEC 60950 or IEC 62368-1 for data processing equipment). Further more all configurations shall comply with the requirements for medical electrical systems (see IEC 60601-1-1 or clause 16 of the 3Ed. of IEC 60601-1, 60601-1-2, respectively). Anybody connecting external adapter to medical electrical equipment configurations a medical system and is therefore responsible that the system complies with the requirements for medical electrical systems. Attention is drawn to the fact that local laws take priority over the above mentioned requirements. If in doubt, consult your local representative or the technical service department. Warning: Too frequent measurements can cause injury to the PATIENT due to blood flow interference. Warning: Don’t place the cuff over wound part. Warning: Pressurization of the CUFF can temporarily cause loss of function of simultaneously used monitoring ME EQUIPMENT on the same limb. 1.2 Warnings and Precautions 54 2.Important Information on Blood Pressure and its Measurement 2.1. How does high or low blood pressure arise? Your level of blood pressure is determined in the circulatory center of the brain and adjusts to a variety of situations through feedback from the nervous system. To adjust blood pressure, the strength and speed of the heart (Pulse), as well as the width of circulatory blood vessels is alter…

Text truncated - open the document above for the full version.

ShenzhenJamrTechnologyCo.,Ltd 09-11-2024 EurofinsElectricalandElectronicTestingNA,Inc. 914WestPatapscoAvenue Baltimore,MD21230 RE:AttestationStatementsPart2.911(d)(5)(i)requestfor(FCCID:2AS8AB72T) [ShenzhenJamrTechnologyCo.,Ltd](“theapplicant”)certifiesthattheequipmentfor whichauthorizationissoughtisnot“covered”equipmentprohibitedfromreceivingan equipmentauthorizationpursuanttosection2.903oftheFCCrules. Sincerely, FushengLuo ShenzhenJamrTechnologyCo.,Ltd 09-11-2024 EurofinsElectricalandElectronicTestingNA,Inc. 914WestPatapscoAvenue Baltimore,MD21230 RE:AttestationStatementsPart2.911(d)(5)(ii)requestfor(FCCID:2AS8AB72T) [ShenzhenJamrTechnologyCo.,Ltd](“theapplicant”)certifiesthat,asofthedateof thefilingoftheapplication,theapplicantisnotidentifiedontheCoveredListasan entityproducing“covered”equipment. Sincerely, FushengLuo

ShenzhenJamrTechnologyCo.,Ltd. A101-301,D101-201,JamrScience& TechnologyPark,No. 2 GuiyuanRoad, GuixiangCommunity,GuanlanStreet,LonghuaDistrict,518100Shenzhen,PEOPLE'S REPUBLICOF CHINA U.S. Ag ent Designation for Se rv ic e of Pro cess - Certif icatio n At testatio n Letter 09/11/2024 Federa l Communications Commission Au thori zation and Ev aluation Division 1435 Oakland Mills Road Columbia, MD 21046 AT TN.: Reviewing En gineer FCC ID: 2AS8AB72T Fede ra l Registra tion Number (F RN) 0028450880 Per se ct ion 2.911(d)(7) of the FCC rules,ShenzhenJamrTechnologyCo.,Ltd. (“the applica nt”) ce rtifies that the equipment for which authoriza tion is so ught is desi gnated to thefollowing U.S. agent* for service of process: Federa l Registra tion Number (FRN): 0033701590 Company Name: UUX GROUP INC Physical U.S. Company Address: 36 South 18th Avenue, Suite A Brighto n, CO USA 80601 County : Adams Agent nam e: Jac k Fu Agent Email A ddress: uuxforever@ outl ook. com The above co ntact perso n acce pts the obligation for se rvice of process . The applicant accepts to maintain an agent for no less than one year after the gra ntee has terminated all mark eting and import ation or the conclusion of any Commission-re lated pro ceeding involving the equipment. This Agreement is valid unti l: Ete rnally. ApplicantSigned: Signed: Printed name: Fusheng Luo Title:Manager: CompanyName: ShenzhenJamrTechnologyCo.,Ltd. Date :11/09/2024 AgentSigned(ifdifferenttoApplicant): Signed: Printedname:JackFu Title:Manager CompanyName:UUXGROUPINC Date:11/09/2024 * the appl icant mus t des ignat e a cont ac t loc at ed in the Uni ted Stat es for pur pos es of ac ting as the appl icant ’s agentfor ser vice of pr oc es s, regar dl es s of whet her the appl icant is a dom es tic or for ei gn ent ity. An appl icant loc at ed in the Uni ted Stat es may des ignat e itsel f as the agentfor ser vice of pr oc es s.

ShenzhenJamrTechnologyCo.,Ltd AgentAuthorizationLetter 2024-09.11 EurofinsElectricalandElectronicTestingNA,Inc. 914WestPatapscoAvenue Baltimore,MD21230 USA RE:LETTEROFAGENTAUTHORIZATION ToWhomItMayConcern: We,theundersigned,herebyauthorizeShenzhenMostTechnologyServiceCo.,Ltd.toact onourbehalfinallmattersrelatingtoapplicationforequipmentauthorization,includingthe signingofalldocumentsrelatingtothesematters. Wealsoherebycertifythatnopartytotheapplicationauthorizedhereunderissubjecttothe denialofbenefits,includingFCCbenefits,pursuanttoSection5301oftheAnti-DrugAbuse Actof1988,21U.S.C.853(a). Thisagreementexpiresoneyearfromthecurrentdate. Sincerely, Name:FushengLuo Position:RAManager CompanyName:ShenzhenJamrTechnologyCo.,Ltd Address:A101-301,D101-201,JamrScience&TechnologPark,No.2Guiyuan Road,GuanlanStreet,LonghuaDistrict,China Tel/Fax86-755-85292057/86-755-27980758 E-Mail:[email protected]

ShenzhenJamrTechnologyCo.,Ltd LongTermConfidentialityRequestLetter 2024.09.11 EurofinsElectricalandElectronicTestingNA,Inc. 914WestPatapscoAvenue Baltimore,MD21230 USA RE:CONFIDENTIALITYREQUESTFOR(FCCID:2AS8AB72T) ToWhomItMayConcern: Thisletterservesasanofficialrequestforconfidentialityundersections0.457and0.459of CFR47.Wehaverequestedthatthe -e.g.Blockdiagram -e.g.SCH -e.g.OperationalDescription requiredtobesubmittedwiththisapplicationbepermanentlywithheldfrompublicreview. Theabovedocumentsarecompanyproprietaryinformationthatcouldnevergetinto thepossessionofyourcompetition. Pleasecontactmeifthereisanyinformationyoumayneed. Sincerely, Name:FushengLuo Position:RAManager CompanyName:ShenzhenJamrTechnologyCo.,Ltd Address:A101-301,D101-201,JamrScience&TechnologPark,No.2Guiyuan Road,GuanlanStreet,LonghuaDistrict,China Tel/Fax86-755-85292057/86-755-27980758 E-Mail:[email protected]

Model No.: B72T FRONT VIEW OF SAMPLE BACK VIEW OF SAMPLE Model No.: B72T LEFT VIEW OF SAMPLE RIGHT VIEW OF SAMPLE Model No.: B72T TOP VIEW OF SAMPLE BOTTOM VIEW OF SAMPLE Model No.: B72T PHOTO OF THE ENTIRE SAMPLE ADAPTER OF THE SAMPLE

ModelNo.:B72T Page1of3 INTERNALPHOTOOFSAMPLE INTERNALPHOTOOFSAMPLEPCB ModelNo.:B72T Page2of3 INTERNALPHOTOOFSAMPLEPCB INTERNALPHOTOOFSAMPLEPCB ModelNo.:B72T Page3of3 INTERNALPHOTOOFSAMPLEPCB INTERNALPHOTOOFSAMPLEPCB BTantenna

Shenzhen Most Technology Service Co., Ltd. No.5, 2nd Langshan Road, North District, Hi-tech Industrial Park, Nanshan, Shenzhen, Guangdong, China. RF Exposure Evaluation Report Report Reference No. ..................... : FCC ID.. ........................................... : MTEB24080354-H 2AS8AB72T Compiled by ( position+printed name+signature) .. : File administrators Alisa Luo Supervised by ( position+printed name+signature) .. : Test Engineer Sunny Deng Approved by ( position+printed name+signature) .. : Manager Yvette Zhou Date of issue ..................................... : Aug. 26,2024 Representative Laboratory Name .: Shenzhen Most Technology Service Co., Ltd. Address ............................................ : No.5, 2nd Langshan Road, North District, Hi-tech Industrial Park, Nanshan, Shenzhen, Guangdong, China. Applicant’s name ............................ : Shenzhen Jamr Technology Co., Ltd. Address ............................................ : A101-301, D101-201, Jamr Science & Technology Park, No. 2 Guiyuan Road, Guixiang Community,Guanlan Street, Longhua District, 518100 Shenzhen, PEOPLE'S REPUBLIC OF CHINA Test specification/ Standard ..........: 47 CFR Part 1.1307 47 CFR Part 2.1093 TRF Originator .................................. : Shenzhen Most Technology Service Co., Ltd. Shenzhen Most Technology Service Co., Ltd. All rights reserved. This publication may be reproduced in whole or in part for non-commercial purposes as long as the Shenzhen Most Technology Service Co., Ltd. is acknowledged as copyright owner and source of the material. Shenzhen Most Technology Service Co., Ltd. takes no responsibility for and will not assume liability for damages resulting from the reader's interpretation of the reproduced material due to its placement and context. Test item description .....................: Blood Pressure Monitor Trade Mark ....................................... : N/A Model/Type reference....................... : B72T Listed Models .................................. : N/A Modulation Type ............................... : GFSK Operation Frequency ........................ : From 2402MHz to 2480MHz Hardware Version ............................... JMR_PCB_B72/B72T_AC621B_V1.0 Software Version................................. V1 Rating ............................................... : DC 5V by Adapter DC 6V by Batteries Result................................................ : PASS Report No.: MTEB24080354-H Page 2 of 5 T E S T R E P O R T Equipment under Test : Blood Pressure Monitor Model /Type : B72T Listed Models : N/A Remark N/A Applicant : Shenzhen Jamr Technology Co., Ltd. Address : A101-301, D101-201, Jamr Science & Technology Park, No. 2 Guiyuan Road, Guixiang Community,Guanlan Street, Longhua District, 518100 Shenzhen, PEOPLE'S REPUBLIC OF CHINA Manufacturer : Shenzhen Jamr Technology Co., Ltd Address : A101-301, D101-201, Jamr Science & Technology Park, No. 2 Guiyuan Road, Guixiang Community,Guanlan Street, Longhua District, 518100 Shenzhen, PEOPLE'S REPUBLIC OF CHINA Test Result: PASS The test report merely corresponds to the test sample. It is not permitted to copy extracts of these test result without the written permission of the test laboratory. Report No.: MTEB24080354-H Page 3 of 5 1. R e v i s i o n H i s t o r y Revision Issue Date Revisions Revised By 00 2024.08.26 Initial Issue Alisa Luo Report No.: MTEB24080354-H Page 4 of 5 2. S A R E v a l u a t i o n 2.1 RF Exposure Compliance Requirement 2.1.1 Standard Requirement According to KDB447498D01 General RF Exposure Guidance v06 4.3.1. Standalone SAR test exclusion considerations Unless specifically required by the published RF exposure KDB procedures, standalone 1-g head or body and 10-g extremity SAR evaluation for general population exposure conditions, by measurement or numerical simulation, is not required when the corresponding SAR Exclusion Threshold condition, listed below, is satisfied. 2.1.2 Limits The 1-g and 10-g SAR test exclusion thresholds for 100 MHz to 6 GHz at test separation distances ≤ 50 mm are determined by: [(max. power of channel, including tune-up tolerance, mW)/(min. test separation distance, mm)] · [√f(GHz)] ≤ 3.0 for 1-g SAR and ≤ 7.5 for 10-g extremity SAR, where The test exclusions are applicable only when the minimum test separation distance is ≤ 50 mm and for transmission frequencies between 100 MHz and 6 GHz. When the minimum test separation distance is < 5 mm, a distance of 5 mm is applied to determine SAR test exclusion Report No.: MTEB24080354-H Page 5 of 5 2.1.3 EUT RF Exposure Measurement Data BLE GFSK Test channel Peak Output Power (dBm) Tune up tolerance (dBm) Maximum tune-up Power (dBm) Lowest(2402MHz) 3.062 3.062±1 4.062 Middle(2440MHz) 2.914 2.914±1 3.914 Highest(2480MHz) 3.605 3.605±1 4.605 Worst case: GFSK Channel Maximum Peak Conducted Output Power (dBm) Maximum tune-up Power Calculated value Exclusion threshold SAR Test Exclusion (dBm) (mW) Highest(2480MHz) 3.605 4.605 2.89 0.91 3.0 Yes .......................THE END OF REPORT.........................

ShenzhenMostTechnologyServiceCo.,Ltd. No.5,2ndLangshanRoad,NorthDistrict,Hi-techIndustrialPark,Nanshan, Shenzhen,Guangdong,China. TESTREPORT FCCRulesPart15.247 ReportReferenceNo........................: FCCID................................................: MTEB24080354-R 2AS8AB72T Compiledby (position+printedname+signature)..:FileadministratorsAlisaLuo Supervisedby (position+printedname+signature)..:TestEngineerSunnyDeng Approvedby (position+printedname+signature)..: ManagerYvetteZhou Dateofissue.........................................:Aug.26,2024 RepresentativeLaboratoryName.:ShenzhenMostTechnologyServiceCo.,Ltd. Address ................................................. : No.5,2ndLangshanRoad,NorthDistrict,Hi-techIndustrialPark, Nanshan,Shenzhen,Guangdong,China. Applicant’sname...............................: ShenzhenJamrTechnologyCo.,Ltd. Address ................................................. : A101-301,D101-201,JamrScience&TechnologyPark,No.2 GuiyuanRoad,GuixiangCommunity,GuanlanStreet,Longhua District,518100Shenzhen,PEOPLE'SREPUBLICOFCHINA Testspecification/Standard ............ : FCCRulesPart15.247 TRFOriginator......................................:ShenzhenMostTechnologyServiceCo.,Ltd. ShenzhenMostTechnologyServiceCo.,Ltd.Allrightsreserved. Thispublicationmaybereproducedinwholeorinpartfornon-commercialpurposesaslongasthe ShenzhenMostTechnologyServiceCo.,Ltd.isacknowledgedascopyrightownerandsourceofthe material.ShenzhenMostTechnologyServiceCo.,Ltd.takesnoresponsibilityforandwillnotassume liabilityfordamagesresultingfromthereader'sinterpretationofthereproducedmaterialduetoits placementandcontext. Testitemdescription ........................ : BloodPressureMonitor TradeMark...........................: N/A Model/Typereference ......................... : B72T ListedModels.....................................:N/A ModulationType..................................:GFSK OperationFrequency..........................:From2402MHzto2480MHz HardwareVersion....................................JMR_PCB_B72/B72T_AC621B_V1.0 SoftwareVersion.....................................V1 Rating ..................................................... : DC5VbyAdapter DC6VbyBatteries Result ..................................................... :PASS ReportNo.:MTEB24080354-RPage 2 of 38 TESTREPORT EquipmentunderTest:BloodPressureMonitor Model/Type:B72T ListedModels:N/A RemarkN/A Applicant: ShenzhenJamrTechnologyCo.,Ltd. Address: A101-301,D101-201,JamrScience&TechnologyPark,No.2 GuiyuanRoad,GuixiangCommunity,GuanlanStreet,Longhua District,518100Shenzhen,PEOPLE'SREPUBLICOFCHINA Manufacturer:ShenzhenJamrTechnologyCo.,Ltd Address : A101-301,D101-201,JamrScience&TechnologyPark,No.2 GuiyuanRoad,GuixiangCommunity,GuanlanStreet,Longhua District,518100Shenzhen,PEOPLE'SREPUBLICOFCHINA TestResult : PASS Thetestreportmerelycorrespondstothetestsample. Itisnotpermittedtocopyextractsofthesetestresultwithoutthewrittenpermissionofthetest laboratory. ReportNo.:MTEB24080354-RPage 3 of 38 Contents 1.REVISIONHISTORY.........................................................................................................................4 2.TESTSTANDARDS............................................................................................................................5 3.SUMMARY...............................................................................................................................................6 3.1.GeneralRemarks.........................................................................................................................................6 3.2.ProductDescription....................................................................................................................................6 3.3.EquipmentUnderTest................................................................................................................................6 3.4.ShortdescriptionoftheEquipmentunderTest(EUT)............................................................................6 3.5.EUToperationmode....................................................................................................................................7 3.6.BlockDiagramofTestSetup......................................................................................................................7 3.7.TestItem(EquipmentUnderTest)Description*.......................................................................................7 3.8.AuxiliaryEquipment(AE)Description.......................................................................................................7 3.9.AntennaInformation*..................................................................................................................................8 3.10.EUTconfiguration......................................................................................................................................8 3.11.Modifications..............................................................................................................................................8 4.TESTENVIRONMENT.......................................................................................................................9 4.1.Addressofthetestlaboratory...................................................................................................................9 4.2.Environmentalconditions...........................................................................................................................9 4.3.TestDescription.........................................................................................................................................10 4.4.Statementofthemeasurementuncertainty...........................................................................................10 4.5.EquipmentsUsedduringtheTest...........................................................................................................11 5.TESTCONDITIONSANDRESULTS....................…

Text truncated - open the document above for the full version.

Report No.: E202212139826-1 Page 2 of 20 Statement 1. The report is invalid without "special seal for inspection and testing"; some copies are invalid; The report is invalid if it is altered or missing; The report is invalid without the signature of the person who prepared, reviewed and approved it. 2. The sample information is provided by the client and responsible for its authenticity; The content of the report is only valid for the samples sent this time. 3. When there are reports in both Chinese and English, the Chinese version will prevail when the language problems are inconsistent. 4. If there is any objection concerning the report, please inform us within 15 days from the date of receiving the report. 5. Without the agreement of the laboratory, the client is not authorized to use the test results for unapproved propaganda. ------------ The following blanks ------------ Report No.: E202212139826-1 Page 3 of 20 TABLE OF CONTENTS 1. TEST RESULT SUMMARY ...................................................................................................................... 5 2. GENERAL DESCRIPTION OF EUT ......................................................................................................... 6 2.1 APPLICANT INFORMATION ...................................................................................................................... 6 2.2 MANUFACTURER ........................................................................................................................................ 6 2.3 FACTORY ...................................................................................................................................................... 6 2.4 BASIC DESCRIPTION OF EUT ................................................................................................................... 6 2.5 TEST SCENE .................................................................................................................................................. 6 2.6 SAMPLE WORK DESCRIPTION ................................................................................................................. 6 2.7 ASSISTIVE DEVICE INFORMATION......................................................................................................... 7 2.8 SAMPLE CONNECTION DIAGRAM .......................................................................................................... 7 3. LABORATORY .......................................................................................................................................... 8 4. MEASUREMENT UNCERTAINTY .......................................................................................................... 9 5. EQUIPMENT AND TOOLS USED DURING TEST .............................................................................. 10 6. ANTENNA RADIATION PERFORMANCE MEASUREMENT ........................................................... 11 6.1 LI MITS ......................................................................................................................................................... 11 6.2 TEST PROCEDURE ..................................................................................................................................... 11 6.3 CONFIGURATION OF SYSTEM UNDER TEST ...................................................................................... 12 6.4 TEST PHOTOS ............................................................................................................................................. 12 6.5 TEST RESULTS ........................................................................................................................................... 13 7. PHOTOGRAPH OF THE EUT ................................................................................................................. 19 ------------ The following blanks ------------ Report No.: E202212139826-1 Page 4 of 20 REPORT ISSUED HISTORY Report Version Report No. Description Compile Date 1.0 E202212139826-1 Original Issue 2023-03-15 ------------ The following blanks ------------ Report No.: E202212139826-1 Page 5 of 20 1. TEST RESULT SUMMARY Test Item Test Frequency Test Method Test Scene Test Result Gain 2400 MHz ~2500MHz ANSI IEEE 149-2021 Part 8 scene 1 / 1) Radiation efficiency 2400 MHz ~2500MHz ANSI IEEE 149-2021 Part 10 scene 1 / 1) Radiation pattern 2400 MHz ~2500MHz ANSI IEEE 149-2021 Part 7 scene 1 / 1) Note 1)：Customer-defined test, test results do not make judgment. ------------ The following blanks ------------ . Report No.: E202212139826-1 Page 6 of 20 2. GENERAL DESCRIPTION OF EUT 2.1 APPLICANT INFORMATION Name: Shenzhen Jamr Technology Co., Ltd. Address: A101-301, D101-201, Jamr Science & Technology Park, No. 2 Guiyuan Road, Guixiang Community, Guanlan Street, Longhua District, Shenzhen 518100, PEOPLE'S REPUBLIC OF CHINA 2.2 MANUFACTURER Name: Shenzhen Jamr Technology Co., Ltd. Address: A101-301, D101-201, Jamr Science & Technology Park, No. 2 Guiyuan Road, Guixiang Community, Guanlan Street, Longhua District, Shenzhen 518100, PEOPLE'S REPUBLIC OF CHINA 2.3 FACTORY Name: Shenzhen Jamr Technology Co., Ltd. Address: A101-301, D101-201, Jamr Science & Technology Park, No. 2 Guiyuan Road, Guixiang Community, Guanlan Street, Longhua District, Shenzhen 518100, PEOPLE'S REPUBLIC OF CHINA 2.4 BASIC DESCRIPTION OF EUT Product Name: Upper Arm Type Blood Pressure Monitor Product Model: Bluetooth module antenna gain Trade Name: / Product Size: / Software Version / Hardware Version / Antenna Type： PCB Antenna Frequency Band: 2400MHz – 2500MHz Sample submitting way: ■Provided by customer □Sampling Sample No: E202212139826-0001 Note: 2.5 TEST SCENE Scene Scene description Test scene 1 Free space 2.6 SAMPLE WORK DESCRIPTION Serial No. Work description a) The sample is erected according to the standard, so that the sample can be tested under normal operation Report No.: E202212139826-1 Page 7 of 20 2.7 ASSISTIVE DEVICE …

Text truncated - open the document above for the full version.

Model No.: B72T CE TEST SETUP RE TEST SETUP Model No.: B72T RE TEST SETUP