2ASK3CT-6330TPower Craze Safari Racer

Colors and styles may vary slightly. FCC Part 15 C Notice CAUTION: Changes or modifications not expressly approved by the party responsible for compliance could void the user’s authority to operate the equipment. NOTE: This equipment has been tested and found to comply with the limits for a Class B digital device, pursuant to Part 15 of the FCC Rules. These limits are designed to provide reasonable protection against harmful interference in a residential installation. This equipment generates, uses and can radiate radio frequency energy and, if not installed and used in accordance with the instructions, may cause harmful interference to radio communications. However, there is no guarantee that interference will not occur in a particular installation. If this equipment does cause harmful interference to radio or television reception, which can be determined by turning the equipment off and on, the user is encouraged to try to correct the interference by one or more of the following measures: • Reorient or relocate the receiving antenna. • Increase the separation between the equipment and receiver. • Connect the equipment into an outlet on a circuit different from that to which the receiver is connected. • Consult the dealer or experienced radio/TV technician for help. This device complies with Part 15 of the FCC Rules. Operation is subject to the following two conditions : (1) this device may not cause harmful interference, and (2) this device must accept any interference received, including interference that may cause undesired operation. INSTRUCTION MANUAL Conforms to safety requirements of ASTM, FCC and CPSIA. WARNING DO NOT USE TRUCK IN INCLEMENT WEATHER! SAFETY WARNINGS! • Improper use of batteries may lead to overheating, breakage or leaking. - Do not mix old and new batteries. - Do not mix different battery brands. - Install batteries with correct polarity. The flat side (negative terminal) of the battery should rest against the spring. - Remove dead batteries immediately. - Avoid liquids, which can short circuit the batteries. - The truck or remote will become unresponsive when batteries are low, at which point you should replace all batteries with new ones. - Remove the batteries if you will not use the truck for a long time. • Avoid using near furniture or glass to prevent damage to these objects. • Do not play on roads. • Do not play in crowded areas to avoid injury or damage. Choose a safe location away from traffic. • Do not use truck during a storm or when lightning or thunder are present. • Do not use in a wet , sandy or muddy environment as truck may become damaged. • Do not modify or attempt to replace the built-in original antenna on the remote or truck. Doing so will damage the set and affect operation. • Do not pull on any wires that are part of the truck. Such action may cause the wires to break and the truck to malfunction. • Keep fingers, hair and clothes away from the truck’s spinning tires. Failure to do so may result in physical injury. • Never aim the truck at other people. • Do not throw the truck or purposely hit it with any object. • Store truck in a cool environment, away from high-temperature sources such as fires, stoves, radiators, etc. • This truck has no user-serviceable parts. Do not attempt to modify components or circuit board. • This toy is only to be connected to equipment bearing either of the following symbols: or RECHARGEABLE BATTERY: This SAFARI RACER uses an internal rechargeable battery and is not replaceable. If the battery no longer stays charged, dispose of it properly according to local disposal requirements. CAUTION: If the rechargeable battery leaks fluid, avoid contact with eyes and dispose of the SAFARI RACER. III Thank you for purchasing the SAFARI RACER™. With proper care, your new SAFARI RACER™ will provide you with many hours of enjoyment. Please read this instruction manual completely before using the product for the first time and then keep this manual in a handy place for future reference. TROUBLESHOOTING Before sending your truck in for repair, please check for a solution below. Possible Cause(s) Weak batteries; no batteries Truck and remote not synced properly Another RC truck may be transmitting on the same radio frequency Using truck in a small enclosed area Using truck indoors Low batteries in transmitter or vehicle Driving truck for too long at high speeds, causing motor to overheat Solution Install new batteries in remote control and recharge the truck. Refer to sync section and re-sync your truck and remote. Move to a new location where no other RC trucks are present. Move outdoors to a large open area. Install new batteries in remote control or recharge your truck. Turn truck off for 10-15 minutes. Problem Truck will not move. Truck does not respond properly to remote control. Truck loses connection to remote control. Truck battery is fully charged, but slower than normal. Limited 90-Day Warranty NORTH AMERICA AMAX Group USA warrants to the original consumer that this product is free from any electrical or mechanical defects for a period of 90 DAYS from the date of purchase. If any such defect is discovered within the warranty period, AMAX Group USA will repair or replace the unit free of charge upon receipt of the unit, shipped postage prepaid and insured to our warranty center ALONG WITH THE ORIGINAL RECEIPT evidencing that the product was purchased from an approved AMAX retail partner and that the product is still within the 90 day warranty period. The warranty covers normal consumer use and does not cover damage that occurs in shipment or failure that results from alterations, accident, misuse, abuse, neglect, wear and tear, inadequate maintenance, commercial use or unreasonable use of the unit. Removal of any parts/components voids all warranties. This warranty does not cover cost of repairs made or attempted outside by third-party individuals or companies. Any applicable implied warranties, including warranties o…

Text truncated - open the document above for the full version.

AMAX INDUSTRIAL GROUP CHINA CO., LTD Date: 2021/3/17 Federal Communications Commission 7435 Oakland Mills Road Columbia MD 21046 To whom it may concern: I, the undersigned, hereby authorize UL Verification Services Inc. to act on our behalf in all manners relating to application for equipment authorization, including signing of all documents relating to these matters. Any and all acts carried out by UL Verification Services Inc. on our behalf shall have the same effect as acts of our own. I, the undersigned, hereby certify that we are not subject to a denial of federal benefits, that includes FCC benefits, pursuant to Section 5301 of the Anti-Drug Abuse Act of 1988, 21 U.S.C. 853(a). In authorizing UL Verification Services Inc. as our representative, we still recognize that we are responsible to: a) comply with the relevant provisions of the certification program; b) make all necessary arrangements for the conduct of the evaluation, including provision for examining documentation and access to all areas, records (including internal audit reports) and personnel for the purposes of evaluation (e.g. testing, inspection, assessment, surveillance, reassessment) and resolution of complaints; c) make claims regarding certification only in respect of the scope for which certification has been granted; d) do not use our product certification in such a manner as to bring the Certification Division into disrepute and not make any statement regarding our product certification which the Certification Division may consider misleading or unauthorized; e) upon suspension or cancellation of certification, discontinue use of all advertising matter that contains any reference thereto and return any certification documents as required by the Certification Division; f) use certification only to indicate the products are certified as being in conformity with specified standards; g) endeavor to ensure that no certificate or report nor any part thereof is used in a misleading manner; h) ensure that any reference to our product certification in communication media such as documents, brochures or advertising, complies with the requirements of the Certification Division; i) keep a record of all complaints made known to us relating to the product’s compliance with requirements of the relevant standard and to make these records available to the when requested; j) take appropriate action with respect to such complaints and any deficiencies found in products or services that affect compliance with the requirements for certification; k) document the actions taken. This authorization is valid until further written notice from the applicant. Sincerely Yours, Signed by: Company Name: AMAX INDUSTRIAL GROUP CHINA CO., LTD Contact Name: Nancy Chen Title of Person：QA Manager Address: OFFICE NO.3 10/F WITTY COMMERCIAL BUILDING 1A-1L TUNG CHOI STREET MONGKOK KOWLOON HONG KONG

AMAX INDUSTRIAL GROUP CHINA CO., LTD Federal Communications Commission 7435 Oakland Mills Road Columbia MD 21046 Subject: Request for Confidentiality FCC ID: 2ASK3CT-6330T To Whom It May Concern: Pursuant to the provisions of Sections 0.457 and 0.459 of the Commission’s rules (47 CFR §§ 0.457, 0.459), we are requesting the Commission to withhold the following attachments as confidential document from public disclosure indefinitely. Schematic Diagram Block Diagram Theory of Operation Above mentioned document contains detailed system and equipment description are considered as proprietary information in operation of the equipment. The public disclosure of above documents might be harmful to our company and would give competitor an unfair advantage in the market. It is our understanding that all measurement test reports, FCC ID label format and correspondent during certification review process cannot be granted as confidential documents and those information will be available for public review once the grant of equipment authorization is issued. Best Regards Company Name: AMAX INDUSTRIAL GROUP CHINA CO., LTD Contact Name: Nancy Chen Title of Person：QA Manager Address: OFFICE NO.3 10/F WITTY COMMERCIAL BUILDING 1A-1L TUNG CHOI STREET MONGKOK KOWLOON HONG KONG Date:05/07/2021

Appendix I External Photographs Page 2 of 3 UL Verification Services (Guangzhou) Co., Ltd, Song Shan Lake Branch This report shall not be reproduced except in full, without the written approval of UL Verification Services (Guangzhou) Co., Ltd, Song Shan Lake Branch. View of EUT-1 View of EUT-2 Page 3 of 3 UL Verification Services (Guangzhou) Co., Ltd, Song Shan Lake Branch This report shall not be reproduced except in full, without the written approval of UL Verification Services (Guangzhou) Co., Ltd, Song Shan Lake Branch. View of EUT-3 View of EUT-4

Amax Industrial Group China Co. Limited 852.3962.5160 Model Number: CT- 6330 F08B01D05/2021 Shenzhen, China 63.3mm 15.5mm FCC ID: 2ASK3CT-6330T This device complies with part 15 of the FCC Rules. Operation is subject to the following two conditions: (1) This device may not cause harmful interference, and (2) this device must accept any interference received, including interference that may cause undesired operation.

Appendix II Internal Photographs Page 2 of 3 UL Verification Services (Guangzhou) Co., Ltd, Song Shan Lake Branch This report shall not be reproduced except in full, without the written approval of UL Verification Services (Guangzhou) Co., Ltd, Song Shan Lake Branch. Internal View of EUT-1 Internal View of EUT-2 Page 3 of 3 UL Verification Services (Guangzhou) Co., Ltd, Song Shan Lake Branch This report shall not be reproduced except in full, without the written approval of UL Verification Services (Guangzhou) Co., Ltd, Song Shan Lake Branch. Internal View of EUT-3 Internal View of EUT-4 Antenna

The results reported herein have been performed in accordance with the laboratory’s terms of accreditation. This report shall not be reproduced except in full without the written approval of the Laboratory. The results in this report apply to the test sample(s) mentioned above at the time of the testing period only and are not to be used to indicate applicability to other similar products. CFR 47 FCC PART 15 SUBPART C ISED RSS-210 ISSUE 10 TEST REPORT For Power Craze Safari Racer MODEL NUMBER FOR FCC: CT-6330 MODEL NUMBER FOR IC: CT-6330T FCC ID: 2ASK3CT-6330T IC: 24796-CT6330T REPORT NUMBER: 4789910817-1 ISSUE DATE: May 10, 2021 Prepared for AMAX INDUSTRIAL GROUP CHINA CO.,LTD OFFICE NO.3 10/F WITTY COMMERCIAL BUILDING 1A-1L TUNG CHOI STREET MONGKOK KOWLOON HONG KONG Prepared by UL Verification Services (Guangzhou) Co., Ltd, Song Shan Lake Branch Building 10, Innovation Technology Park, No. 1, Li Bin Road, Song Shan Lake Hi- Tech Development Zone Dongguan, 523808, People’s Republic of China Tel: +86 769 22038881 Fax: +86 769 33244054 Website: www.ul.com REPORT NO.: 4789910817-1 Page 2 of 50 UL Verification Services (Guangzhou) Co., Ltd, Song Shan Lake Branch FORM NO.: 10-SL-F0058 This report shall not be reproduced except in full, without the written approval of UL Verification Services (Guangzhou) Co., Ltd, Song Shan Lake Branch. Revision History Rev. Issue Date Revisions Revised By V0 05/10/2021 Initial Issue REPORT NO.: 4789910817-1 Page 3 of 50 UL Verification Services (Guangzhou) Co., Ltd, Song Shan Lake Branch FORM NO.: 10-SL-F0058 This report shall not be reproduced except in full, without the written approval of UL Verification Services (Guangzhou) Co., Ltd, Song Shan Lake Branch. Summary of Test Results Clause Test Items FCC/ISED Rules Test Results 1 20dB Bandwidth and 99% Occupied Bandwidth CFR 47 FCC §15.215 (c) ISED RSS-Gen Clause 6.7 Pass 2 Radiated Emission CFR 47 FCC §15.249 (a)(d)(e) ISED RSS-210 Annex B B.10 CFR 47 FCC §15.205 and §15.209 RSS-GEN Clause 8.9 RSS-GEN Clause 8.10 Pass 3 Antenna Requirement CFR 47 FCC §15.203 ISED RSS-Gen Clause 6.8 Pass Note 1: This test report is only published to and used by the applicant, and it is not for evidence purpose in China. Note 2: The measurement result for the sample received is <Pass> according to < CFR 47 FCC PART 15 SUBPART C, ISED RSS-210 Issue 10 and ISED RSS-GEN Issue 5 > when <Accuracy Method> decision rule is applied. REPORT NO.: 4789910817-1 Page 4 of 50 UL Verification Services (Guangzhou) Co., Ltd, Song Shan Lake Branch FORM NO.: 10-SL-F0058 This report shall not be reproduced except in full, without the written approval of UL Verification Services (Guangzhou) Co., Ltd, Song Shan Lake Branch. TABLE OF CONTENTS 1. ATTESTATION OF TEST RESULTS ................................................................................. 5 2. TEST METHODOLOGY ..................................................................................................... 6 3. FACILITIES AND ACCREDITATION ................................................................................. 6 4. CALIBRATION AND UNCERTAINTY ................................................................................ 7 4.1. MEASURING INSTRUMENT CALIBRATION .............................................................. 7 4.2. MEASUREMENT UNCERTAINTY ............................................................................... 7 5. EQUIPMENT UNDER TEST ............................................................................................... 8 5.1. DESCRIPTION OF EUT .............................................................................................. 8 5.2. MAXIMUM FIELD STRENGTH .................................................................................... 8 5.3. CHANNEL LIST ........................................................................................................... 8 5.4. DESCRIPTION OF AVAILABLE ANTENNAS .............................................................. 8 5.5. TEST CHANNEL CONFIGURATION ........................................................................... 8 5.6. THE WORSE CASE POWER SETTING PARAMETER ............................................... 8 5.7. TEST ENVIRONMENT ................................................................................................ 9 5.8. DESCRIPTION OF TEST SETUP ...............................................................................10 5.9. MEASURING INSTRUMENT AND SOFTWARE USED ..............................................11 6. ANTENNA PORT TEST RESULTS ...................................................................................12 6.1. ON TIME AND DUTY CYCLE .....................................................................................12 6.2. 20 dB BANDWIDTH AND 99% OCCUPIED BANDWIDTH .........................................14 7. RADIATED TEST RESULTS .............................................................................................18 7.1. LIMITS AND PROCEDURE ........................................................................................18 7.2. RESTRICTED BANDEDGE AND FIELD STRENGTH OF INTENTIONAL EMISSIONS 25 7.3. SPURIOUS EMISSIONS (1~3GHz) ............................................................................31 7.4. SPURIOUS EMISSIONS (3~18GHz) ..........................................................................37 7.5. SPURIOUS EMISSIONS (18~26GHz) ........................................................................43 7.6. SPURIOUS EMISSIONS BELOW 30MHz ..................................................................45 7.7. SPURIOUS EMISSIONS BELOW 1GHz AND ABOVE 30MHz ...................................48 8. ANTENNA REQUIREMENTS ............................................................................................50 REPORT NO.: 4789910817-1 Page 5 of 50 UL Verification Services (Guangzhou) Co., Ltd, Song Shan Lake Branch FORM NO.: 10-SL-F0058 This report shall not be reproduced except in full, with…

Text truncated - open the document above for the full version.

Appendix II Setup Photographs RADIATED RF MEASUREMENT SETUP (30MHz ~ 1 GHz) RADIATED RF MEASUREMENT SETUP (Below 30MHz) RADIATED RF MEASUREMENT SETUP (Above 1G – X axis) RADIATED RF MEASUREMENT SETUP (Above 1G – Y axis) RADIATED RF MEASUREMENT SETUP (Above 1G – Z axis)