2ATZ4BGSPmart phone

FCC Statement 1. This device complies with Part 15 of the FCC Rules. Operation is subject to the following two conditions: (1) This device may not cause harmful interference. (2) This device must accept any interference received, including interference that may cause undesired operation. 2. Changes or modifications not expressly approved by the party responsible for compliance could void the user's authority to operate the equipment. NOTE: This equipment has been tested and found to comply with the limits for a Class B digital device, pursuant to Part 15 of the FCC Rules. These limits are designed to provide reasonable protection against harmful interference in a residential installation. This equipment generates uses and can radiate radio frequency energy and, if not installed and used in accordance with the instructions, may cause harmful interference to radio communications. However, there is no guarantee that interference will not occur in a particular installation. If this equipment does cause harmful interference to radio or television reception, which can be determined by turning the equipment off and on, the user is encouraged to try to correct the interference by one or more of the following measures: Reorient or relocate the receiving antenna. Increase the separation between the equipment and receiver. Connect the equipment into an outlet on a circuit different from that to which the receiver is connected. Consult the dealer or an experienced radio/TV technician for help. SAR Information Statement Your wireless phone is a radio transmitter and receiver. It is designed and manufactured not to exceed the emission limits for exposure to radiofrequency (RF) energy set by the Federal Communications Commission of the U.S. Government. These limits are part of comprehensive guidelines and establish permitted levels of RF energy for the general population. The guidelines are based on standards that were developed by independent scientific organizations through periodic and thorough evaluation of scientific studies. The standards include a substantial safety margin designed to assure the safety of all persons, regardless of age and health. The exposure standard for wireless mobile phones employs a unit of measurement known as the Specific Absorption Rate, or SAR. The SAR limit set by the FCC is 1.6 W/kg. * Tests for SAR are conducted with the phone transmitting at its highest certified power level in all tested frequency bands. Although the SAR is determined at the highest certified power level, the actual SAR level of the phone while operating can be well below the maximum value. This is because the phone is designed to operate at multiple power levels so as to use only the power required to reach the network. In general, the closer you are to a wireless base station antenna, the lower the power output. Before a phone model is available for sale to the public, it must be tested and certified to the FCC that it does not exceed the limit established by the government adopted requirement for safe exposure. The tests are performed in positions and locations (e.g., at the ear and worn on the body) as required by the FCC for each model. The highest SAR value for this model phone when tested for use at the ear is1.196W/Kgand when worn on the body, as described in this user guide, is0.3367W/Kg(Body-worn measurements differ among phone models, depending upon available accessories and FCC requirements). The maximum scaled SAR in hotspot mode is 0.369W/Kg. While there may be differences between the SAR levels of various phones and at various positions, they all meet the government requirement for safe exposure. The FCC has granted an Equipment Authorization for this model phone with all reported SAR levels evaluated as in compliance with the FCC RFexposure guidelines. SAR information on this model phone is on file with the FCC and can be found under the Display Grant section of http://www.fcc.gov/ oet/fccid after searching on FCC ID: 2ATZ4BGSP Additional information on Specific Absorption Rates (SAR) can be found on the Cellular Telecommunications Industry Asso-ciation (CTIA) web-site at http://www.wow-com.com. * In the United States and Canada, the SAR limit for mobile phones used by the public is 1.6 watts/kg (W/kg) averaged over one gram of tissue. The standard incorporates a sub-stantial margin of safety to give additional protection for the public and to account for any variations in measurements. 5150-5250MHz is only for indoor use Body-worn Operation This device was tested for typical body-worn operations. To comply with RF exposure requirements, a minimum separation distance of 10mm must be maintained between the user’s body and the handset, including the antenna. Third-party belt-clips, holsters, and similar accessories used by this device should not contain any metallic components. Body-worn accessories that do not meet these requirements may not comply with RF exposure requirements and should be avoided. Use only the supplied or an approved IC STATEMENT This device complies with Industry Canada licence-exempt RSS standard(s) Operation is subject to the following two conditions: (1) This device may not cause interference, and (2) This device must accept any interference, including interference that may cause undesired operation of the device. This equipment complies with IC radiation exposure limits set forth for an uncontrolled environment. End user must follow the specific operating instructions for satisfying RF exposure compliance. This transmitter must not be co-located or operating in conjunction with any other antenna or transmitter. These requirements set a SAR limit of 1.6 W/kg averaged over one gram of tissue. The highest SAR value for this model phone when tested for use at the ear is 1.196W/Kg and when worn on the body is 0.336 W/Kg. The maximum scaled SAR in hotspot mode is 0.387W/Kg.This device was tested for typical body-worn operations. To comply with RF exposurerequireme…

Text truncated - open the document above for the full version.

FCC Software Configuration Control Declaration Rev1.1 Shenzhen Youmi Intelligent Technology Co., Ltd. FCC Software Configuration Control Declaration Date: November 12, 2020 Federal Communications Commission 7435 Oakland Mills Road Columbia, MD 21046 USA Attn: OET Dept. Product/ Model Number:Smart Phone /BISON/BISON GT/BISON S/BISON Pro Regarding FCC Country Code Selection guidelines identified in KDB 594280. “All applications for equipment authorization for transmitters that can have radio parameters, or other technical parameters, reported to the Commission set by software must have an attestation indicating that no third party will have software, or configuration control, to program the device out of compliance of the technical rules under which it has been certified.” We declare that no third party will have software, or configuration control, to program the device out of compliance of the technical rules under which it has been certified. Name:wangkun Date: 2020-11-12 Title:Manager Signature of applicant

Shenzhen Youmi Intelligent Technology Co., Ltd. Agent Authorization Company: Shenzhen Youmi Intelligent Technology Co., Ltd. Address: 406-407 Jinqi Zhigu Building,4/F,1 Tangling Road,Nanshan District, Shenzhen City,China Product Name: Smart phone Model Number(s): BISON、BISON GT、BISON S、BISON Pro Product Description: Smart phone We authorize MiCOM Labs Inc., 575 Boulder Court, Pleasanton, California 94566, USA, to act on our behalf on all matters concerning the certification of above named equipment. We declare that MiCOM Labs Inc. is allowed to forward all information related to the approval and certification of equipment to the regulatory agencies as required and to discuss any issues concerning the approval application. Any and all acts carried out by MiCOM Labs on our behalf shall have the same effect as acts of our own. Signature: Date: 2020-11-12 Name: wangkun Title: manager Company: Shenzhen Youmi Intelligent Technology Co., Ltd.

Shenzhen Youmi Intelligent Technology Co., Ltd. Office of Engineering Technology Federal Communications Commission 7435 Oakland Mills Road Columbia, MD 21046 USA Date: 2020-11-12 Subject; Request for Confidentiality FCC ID: 2ATZ4BGSP To Whom It May Concern, Pursuant to the provisions of the Commission’s rules Title 47 Sections §0.457 and §0.459, we are requesting the Commission to withhold the following attachment(s) as confidential documents from public disclosure indefinitely. These documents contain detailed system and equipment descriptions and are considered as proprietary information in operation of the equipment. The public disclosure of these documents might be harmful to our company and would give competitors an unfair advantage in the market. Schematic Diagram Block Diagram Parts List Operational Description Tune-up Procedure In additional to above mentioned documents, in order to comply with the marketing regulations in Title 47 CFR §2.803 and the importation rules in Title 47 CFR §2.1204, while ensuring that business sensitive information remains confidential until the actual marketing of newly authorized devices, we request Short Term Confidentiality of the following attachment(s); External Photos Test Setup Photos Internal Photos User Manual For 45 days, pursuant to Public Notice DA 04-1705. OR For 180 days pursuant to KDB 726920 D01. It is our understanding that all measurement test reports, FCC ID label format and correspondence during the certification review process cannot be granted as confidential documents and this information will be available for public review once the grant of equipment authorization is issued. Sincerely, Signature: Name: wangkun Title: manager

Declaration Letter We, Shenzhen Youmi Intelligent Technology Co., Ltd.declared that our product Smart phone item No.: BISON、BISON GT、BISON S、BISON Pro were identical inside, the electrical circuit design, layout, components used and internal wiring, with only difference being model name。 Sincerely your Signature: Name/Title: Wangkun / manager Tel. No.: 86-13590152505 E-Mail: [email protected] Company: Shenzhen Youmi Intelligent Technology Co., Ltd. Date：2020-11-12

Report No: JYTSZE200905501 JianYan Testing Group Shenzhen Co., Ltd. Project No.: JYTSZE2009055 No.110~116, Building B, Jinyuan Business Building, Xixiang Road, Bao’an District, Shenzhen, Guangdong, China Tel: +86-755-23118282, Fax: +86-755-23116366 Page 49 of 62 8 EUT Constructional Details Report No: JYTSZE200905501 JianYan Testing Group Shenzhen Co., Ltd. Project No.: JYTSZE2009055 No.110~116, Building B, Jinyuan Business Building, Xixiang Road, Bao’an District, Shenzhen, Guangdong, China Tel: +86-755-23118282, Fax: +86-755-23116366 Page 50 of 62 Report No: JYTSZE200905501 JianYan Testing Group Shenzhen Co., Ltd. Project No.: JYTSZE2009055 No.110~116, Building B, Jinyuan Business Building, Xixiang Road, Bao’an District, Shenzhen, Guangdong, China Tel: +86-755-23118282, Fax: +86-755-23116366 Page 51 of 62 Report No: JYTSZE200905501 JianYan Testing Group Shenzhen Co., Ltd. Project No.: JYTSZE2009055 No.110~116, Building B, Jinyuan Business Building, Xixiang Road, Bao’an District, Shenzhen, Guangdong, China Tel: +86-755-23118282, Fax: +86-755-23116366 Page 52 of 62

label location label location

Report No: JYTSZE200905501 JianYan Testing Group Shenzhen Co., Ltd. Project No.: JYTSZE2009055 No.110~116, Building B, Jinyuan Business Building, Xixiang Road, Bao’an District, Shenzhen, Guangdong, China Tel: +86-755-23118282, Fax: +86-755-23116366 Page 53 of 62 Report No: JYTSZE200905501 JianYan Testing Group Shenzhen Co., Ltd. Project No.: JYTSZE2009055 No.110~116, Building B, Jinyuan Business Building, Xixiang Road, Bao’an District, Shenzhen, Guangdong, China Tel: +86-755-23118282, Fax: +86-755-23116366 Page 54 of 62 Report No: JYTSZE200905501 JianYan Testing Group Shenzhen Co., Ltd. Project No.: JYTSZE2009055 No.110~116, Building B, Jinyuan Business Building, Xixiang Road, Bao’an District, Shenzhen, Guangdong, China Tel: +86-755-23118282, Fax: +86-755-23116366 Page 55 of 62 Report No: JYTSZE200905501 JianYan Testing Group Shenzhen Co., Ltd. Project No.: JYTSZE2009055 No.110~116, Building B, Jinyuan Business Building, Xixiang Road, Bao’an District, Shenzhen, Guangdong, China Tel: +86-755-23118282, Fax: +86-755-23116366 Page 56 of 62 Report No: JYTSZE200905501 JianYan Testing Group Shenzhen Co., Ltd. Project No.: JYTSZE2009055 No.110~116, Building B, Jinyuan Business Building, Xixiang Road, Bao’an District, Shenzhen, Guangdong, China Tel: +86-755-23118282, Fax: +86-755-23116366 Page 57 of 62 Report No: JYTSZE200905501 JianYan Testing Group Shenzhen Co., Ltd. Project No.: JYTSZE2009055 No.110~116, Building B, Jinyuan Business Building, Xixiang Road, Bao’an District, Shenzhen, Guangdong, China Tel: +86-755-23118282, Fax: +86-755-23116366 Page 58 of 62 Report No: JYTSZE200905501 JianYan Testing Group Shenzhen Co., Ltd. Project No.: JYTSZE2009055 No.110~116, Building B, Jinyuan Business Building, Xixiang Road, Bao’an District, Shenzhen, Guangdong, China Tel: +86-755-23118282, Fax: +86-755-23116366 Page 59 of 62 Report No: JYTSZE200905501 JianYan Testing Group Shenzhen Co., Ltd. Project No.: JYTSZE2009055 No.110~116, Building B, Jinyuan Business Building, Xixiang Road, Bao’an District, Shenzhen, Guangdong, China Tel: +86-755-23118282, Fax: +86-755-23116366 Page 60 of 62 Report No: JYTSZE200905501 JianYan Testing Group Shenzhen Co., Ltd. Project No.: JYTSZE2009055 No.110~116, Building B, Jinyuan Business Building, Xixiang Road, Bao’an District, Shenzhen, Guangdong, China Tel: +86-755-23118282, Fax: +86-755-23116366 Page 61 of 62 Report No: JYTSZE200905501 JianYan Testing Group Shenzhen Co., Ltd. Project No.: JYTSZE2009055 No.110~116, Building B, Jinyuan Business Building, Xixiang Road, Bao’an District, Shenzhen, Guangdong, China Tel: +86-755-23118282, Fax: +86-755-23116366 Page 62 of 62 ------End of report------

JianYan Testing Group Shenzhen Co., Ltd. Report No: JYTSZE200905601 Authorized Signature: Bruce Zhang Laboratory Manager This report details the results of the testing carried out on one sample. The results contained in this test report do not relate to other samples of the same product and does not permit the use of the JYT product certification mark. The manufacturer should ensure that all products in series production are in conformity with the product sample detailed in this report. This report may only be reproduced and distributed in full. If the product in this report is used in any configuration other than that detailed in the report, the manufacturer must ensure the new system complies with all relevant standards. This document cannot be reproduced except in full, without prior written approval of the Company. Any unauthorized alteration, forgery or falsification of the content or appearance of this document is unlawful and offenders may be prosecuted to the fullest extent of the law. Unless otherwise stated the results shown in this test report refer only to the sample(s) tested and such sample(s) are retained for 90 days only. 1 Cover Page FCC SAR REPORT Applicant: Shenzhen Youmi Intelligent Technology Co., Ltd. Address of Applicant: 406-407 Jinqi Zhigu Building,4/F,1 Tangli ng Road,Nanshan District, Shenzhen City,China. Equipment Under Test (EUT) Product Name: Smart phone Model No.: BISON, BISON GT, BISON S, BISON Pro Trade mark UMIDIGI FCC ID: 2ATZ4BGSP Applicable standards: FCC 47 CFR Part 2.1093 Date of Test: 19 Oct., 2020 ~ 25 Oct., 2020 Test Result: Maximum Reported 1-g SAR (W/kg) Head: 1.196 Body: 0.336 Hotspot: 0.369 Report No: JYTSZE200905601 JianYan Testing Group Shenzhen Co., Ltd. Project No.: JYTSZE2009056 No.110~116, Building B, Jinyuan Business Building, Xixiang Road, Bao’an District, Shenzhen, Guangdong, China Telephone: +86 (0) 755 23118282 Fax: +86 (0) 755 23116366, E-mail: [email protected] Page 2 of 199 2 Version Version No. Date Description 00 11 Nov., 2020 Original Tested by: Date: 11 Nov., 2020 Report Clerk Reviewed by: Date: 11 Nov., 2020 Project Engineer Report No: JYTSZE200905601 JianYan Testing Group Shenzhen Co., Ltd. Project No.: JYTSZE2009056 No.110~116, Building B, Jinyuan Business Building, Xixiang Road, Bao’an District, Shenzhen, Guangdong, China Telephone: +86 (0) 755 23118282 Fax: +86 (0) 755 23116366, E-mail: [email protected] Page 3 of 199 3 Contents 1 COV ER P AGE ................................................................................................................................................................................. 1 2 VERSION........................................................................................................................................................................................... 2 3 CONTENTS ...................................................................................................................................................................................... 3 4 SAR RES ULTS SUM MARY ....................................................................................................................................................... 5 5 GENERAL INFORMATION ........................................................................................................................................................ 6 5.1 CLIENT INFORMATION....................................................................................................................................................................... 6 5.2 GENERAL DESCRIPTION OF EUT ..................................................................................................................................................... 6 5.3 MA XI MUM RF OUTPUT POWER........................................................................................................................................................ 8 5.4 ENVIRONMENT OF TEST SITE........................................................................................................................................................... 9 5.5 TEST SA MP LE PLAN ......................................................................................................................................................................... 9 5.6 TEST LOCA TION................................................................................................................................................................................ 9 6 INTRODUCTION...........................................................................................................................................................................10 6.1 INTRODUCTION ............................................................................................................................................................................... 10 6.2 SAR DEFINITION ............................................................................................................................................................................ 10 7 RF EXP OSURE LIMITS .............................................................................................................................................................11 7.1 UNCONTROLLED ENVIRONMENT .................................................................................................................................................... 11 7.2 CONTROLLED ENVIRONMENT ......................................................................................................................................................... 11 7.3 RF EXPO SURE LIMITS .................................................................................................................................................................... 11 8 SAR M EASUREM ENT S YSTEM.......................................................................................................................................…

Text truncated - open the document above for the full version.

Report No: JYTSZE200905601 JianYan Testing Group Shenzhen Co., Ltd. Project No.: JYTSZE2009056 No.110~116, Building B, Jinyuan Business Building, Xixiang Road, Bao’an District, Shenzhen, Guangdong, China Telephone: +86 (0) 755 23118282 Fax: +86 (0) 755 23116366, E-mail: [email protected] Page 101 of 199 Test Laboratory: CCIS Date/Time: 10.19.2020 10:21:02 DUT: Smart phone; Type: BISON; Serial: 4# Communication System: UID 0, GSM (0); Frequency: 1880 MHz; Duty Cycle: 1:8.30042 Medium parameters used: f = 1880 MHz; σ = 1.392 S/m; ε r = 39.847; ρ = 1000 kg/m 3 Phantom section: Flat Section DASY5 Configuration:  Probe: EX3DV4 - SN3924; ConvF(8.14, 8.14, 8.14); Calibrated: 09.23.2020;  Sensor-Surface: 1.4mm (Mechanical Surface Detection)  Electronics: DAE4 Sn1373; Calibrated: 07.27.2020  Phantom: SAM 5.0; Type: QD000P40CD; Serial: TP:1765  Measurement SW: DASY52, Version 52.8 (8); SEMCAD X Version 14.6.10 (7331) GSM 1900 Body Back/Middle Channel/Area Scan (51x81x1): Interpolated grid: dx=1.500 mm, dy=1.500 mm Maximum value of SAR (interpolated) = 0.292 W/kg GSM 1900 Body Back/Middle Channel/Zoom Scan (5x5x7)/Cube 0: Measurement grid: dx=8mm, dy=8mm, dz=5mm Reference Value = 6.553 V/m; Power Drift = 0.06 dB Peak SAR (extrapolated) = 0.378 W/kg SAR(1 g) = 0.204 W/kg; SAR(10 g) = 0.109 W/kg Maximum value of SAR (measured) = 0.307 W/kg 0 dB = 0.307 W/kg = -5.13 dBW/kg Report No: JYTSZE200905601 JianYan Testing Group Shenzhen Co., Ltd. Project No.: JYTSZE2009056 No.110~116, Building B, Jinyuan Business Building, Xixiang Road, Bao’an District, Shenzhen, Guangdong, China Telephone: +86 (0) 755 23118282 Fax: +86 (0) 755 23116366, E-mail: [email protected] Page 102 of 199 Test Laboratory: CCIS Date/Time: 10.24.2020 14:47:38 DUT: Smart phone; Type: BISON; Serial: 4# Communication System: UID 0, UMTS-FDD(WCDMA) (0); Frequency: 836.6 MHz; Duty Cycle: 1:1 Medium parameters used (interpolated): f = 836.6 MHz; σ = 0.891 S/m; ε r = 42.134; ρ = 1000 kg/m 3 Phantom section: Flat Section DASY5 Configuration:  Probe: EX3DV4 - SN3924; ConvF(9.71, 9.71, 9.71); Calibrated: 09.23.2020;  Sensor-Surface: 1.4mm (Mechanical Surface Detection)  Electronics: DAE4 Sn1373; Calibrated: 07.27.2020  Phantom: SAM 5.0; Type: QD000P40CD; Serial: TP:1765  Measurement SW: DASY52, Version 52.8 (8); SEMCAD X Version 14.6.10 (7331) WCDMA 850 Body Front/Middle Channel/Area Scan (51x71x1): Interpolated grid: dx=1.500 mm, dy=1.500 mm Maximum value of SAR (interpolated) = 0.279 W/kg WCDMA 850 Body Front/Middle Channel/Zoom Scan (5x5x7)/Cube 0: Measurement grid: dx=8mm, dy=8mm, dz=5mm Reference Value = 16.18 V/m; Power Drift = 0.01 dB Peak SAR (extrapolated) = 0.310 W/kg SAR(1 g) = 0.225 W/kg; SAR(10 g) = 0.168 W/kg Maximum value of SAR (measured) = 0.278 W/kg 0 dB = 0.278 W/kg = -5.56 dBW/kg Report No: JYTSZE200905601 JianYan Testing Group Shenzhen Co., Ltd. Project No.: JYTSZE2009056 No.110~116, Building B, Jinyuan Business Building, Xixiang Road, Bao’an District, Shenzhen, Guangdong, China Telephone: +86 (0) 755 23118282 Fax: +86 (0) 755 23116366, E-mail: [email protected] Page 103 of 199 Test Laboratory: CCIS Date/Time: 10.19.2020 14:08:31 DUT: Smart phone; Type: BISON; Serial: 4# Communication System: UID 0, UMTS-FDD(WCDMA) (0); Frequency: 1732.6 MHz; Duty Cycle: 1:1 Medium parameters used (interpolated): f = 1732.6 MHz; σ = 1.329 S/m; ε r = 40.462; ρ = 1000 kg/m 3 Phantom section: Flat Section DASY5 Configuration:  Probe: EX3DV4 - SN3924; ConvF(8.43, 8.43, 8.43); Calibrated: 09.23.2020;  Sensor-Surface: 1.4mm (Mechanical Surface Detection)  Electronics: DAE4 Sn1373; Calibrated: 07.27.2020  Phantom: SAM 5.0; Type: QD000P40CD; Serial: TP:1765  Measurement SW: DASY52, Version 52.8 (8); SEMCAD X Version 14.6.10 (7331) WCDMA 1700 Body Back/Middle Channel/Zoom Scan (5x5x7)/Cube 0: Measurement grid: dx=8mm, dy=8mm, dz=5mm Reference Value = 5.316 V/m; Power Drift = -0.04 dB Peak SAR (extrapolated) = 0.415 W/kg SAR(1 g) = 0.224 W/kg; SAR(10 g) = 0.117 W/kg Maximum value of SAR (measured) = 0.329 W/kg WCDMA 1700 Body Back/Middle Channel/Area Scan (51x71x1): Interpolated grid: dx=1.500 mm, dy=1.500 mm Maximum value of SAR (interpolated) = 0.351 W/kg 0 dB = 0.351 W/kg = -4.55 dBW/kg Report No: JYTSZE200905601 JianYan Testing Group Shenzhen Co., Ltd. Project No.: JYTSZE2009056 No.110~116, Building B, Jinyuan Business Building, Xixiang Road, Bao’an District, Shenzhen, Guangdong, China Telephone: +86 (0) 755 23118282 Fax: +86 (0) 755 23116366, E-mail: [email protected] Page 104 of 199 Test Laboratory: CCIS Date/Time: 10.19.2020 17:35:11 DUT: Smart phone; Type: BISON; Serial: 4# Communication System: UID 0, UMTS-FDD(WCDMA) (0); Frequency: 1880 MHz; Duty Cycle: 1:1 Medium parameters used: f = 1880 MHz; σ = 1.392 S/m; ε r = 39.847; ρ = 1000 kg/m 3 Phantom section: Flat Section DASY5 Configuration:  Probe: EX3DV4 - SN3924; ConvF(8.14, 8.14, 8.14); Calibrated: 09.23.2020;  Sensor-Surface: 1.4mm (Mechanical Surface Detection)  Electronics: DAE4 Sn1373; Calibrated: 07.27.2020  Phantom: SAM 5.0; Type: QD000P40CD; Serial: TP:1765  Measurement SW: DASY52, Version 52.8 (8); SEMCAD X Version 14.6.10 (7331) WCDMA 1900 Body Back/Middle Channel/Zoom Scan (5x5x7)/Cube 0: Measurement grid: dx=8mm, dy=8mm, dz=5mm Reference Value = 7.181 V/m; Power Drift = 0.14 dB Peak SAR (extrapolated) = 0.545 W/kg SAR(1 g) = 0.299 W/kg; SAR(10 g) = 0.160 W/kg Maximum value of SAR (measured) = 0.454 W/kg WCDMA 1900 Body Back/Middle Channel/Area Scan (51x81x1): Interpolated grid: dx=1.500 mm, dy=1.500 mm Maximum value of SAR (interpolated) = 0.423 W/kg 0 dB = 0.423 W/kg = -3.74 dBW/kg Report No: JYTSZE200905601 JianYan Testing Group Shenzhen Co., Ltd. Project No.: JYTSZE2009056 No.110~116, Building B, Jinyuan Business Building, Xixiang Road, Bao’an District, Shenzhen, Guangdong, China Telephone: +86 (0) 755 23118282 Fax: +86 (0) 755 23116366, E-mail: [email protected] Page 105 of 199 Test Laboratory: CCIS Date/Time: 10.19.2020 22:31:18 DUT: Smart phone; Type: BISON; S…

Text truncated - open the document above for the full version.

JianYan Testing Group Shenzhen Co., Ltd. Report No: JYTSZE200905505V02 Authorized Signature: Bruce Zhang Laboratory Manager This report details the results of the testing carried out on one sample. The results contained in this test report do not relate to other samples of the same product and does not permit the use of the JYT product certification mark. The manufacturer should ensure that all products in series production are in conformity with the product sample detailed in this report. This report may only be reproduced and distributed in full. If the product in this report is used in any configuration other than that detailed in the report, the manufacturer must ensure the new system complies with all relevant standards. This document cannot be reproduced except in full, without prior written approval of the Company. Any unauthorized alteration, forgery or falsification of the content or appearance of this document is unlawful and offenders may be prosecuted to the fullest extent of the law. Unless otherwise stated the results shown in this test report refer only to the sample(s) tested and such sample(s) are retained for 90 days only. 1 Cover Page FCC REPORT (UNII) Applicant: Shenzhen Youmi Intelligent Technology Co., Ltd. Address of Applicant: 406-407 Jinqi Zhigu Building, 4/F, 1 Tangling Road, Nanshan District, Shenzhen City, China. Equipment Under Test (EUT) Product Name: Smart phone Model No.: BISON, BISON GT, BISON S, BISON Pro Trade mark: UMIDIGI FCC ID: 2ATZ4BGSP Applicable standards: FCC CFR Title 47 Part 15 Subpart E Section 15.407 Date of sample receipt: 16 Sep., 2020 Date of Test: 17 Sep., to 13 Oct., 2020 Date of report issued: 16 Nov., 2020 Test Result: PASS* * In the configuration tested, the EUT complied with the standards specified above. Report No: JYTSZE200905505V02 JianYan Testing Group Shenzhen Co., Ltd. Project No.: JYTSZE2009055 No.110~116, Building B, Jinyuan Business Building, Xixiang Road, Bao’an District, Shenzhen, Guangdong, China Telephone: +86 (0) 755 23118282 Fax: +86 (0) 755 23116366 Page 2 of 51 2 Version Version No. Date Description 00 15 Oct., 2020 Original 01 13 Nov., 2020 Update page 4, 13, 19, 25 02 16 Nov., 2020 Update page 4, 19 Tested by: Date: 16 Nov., 2020 Test Engineer Reviewed by: Date: 16 Nov., 2020 Project Engineer Report No: JYTSZE200905505V02 JianYan Testing Group Shenzhen Co., Ltd. Project No.: JYTSZE2009055 No.110~116, Building B, Jinyuan Business Building, Xixiang Road, Bao’an District, Shenzhen, Guangdong, China Telephone: +86 (0) 755 23118282 Fax: +86 (0) 755 23116366 Page 3 of 51 3 Contents Page 1 COVER PAGE ....................................................................................................................................................... 1 2 VERSION ............................................................................................................................................................... 2 3 CONTENTS ........................................................................................................................................................... 3 4 TEST SUMMARY .................................................................................................................................................. 4 5 GENERAL INFORMATION .................................................................................................................................. 5 5.1 CLIENT INFORMATION .................................................................................................................................................... 5 5.2 GENERAL DESCRIPTION OF E.U.T. ............................................................................................................................... 5 5.3 TEST ENVIRONMENT AND MODE .................................................................................................................................... 6 5.4 DESCRIPTION OF SUPPORT UNITS .....................................................................................................................…

Text truncated - open the document above for the full version.