2AU29ALATAAAARERemote

BLISS ™ Automation by Alta 15 CHANNEL REMOTE CONTROL PROGRAMMING AND USERS GUIDE AMP25B Instruction Attention -1- The motor is suitable for motorization of roller blinds, sheer shadings, roman shades, and zebra shades. Never drop, knock, drill or submerge the motor. Keep the power cable in right position as following. Important safety instructions to be read before installation. Incorrect installation can lead to serious injury and will void manufacturer’s liability and warranty. Declarations Do not dispose of in general waste. Please recycle batteries and damaged electrical products appropriately. -2- Safety 1. Do not expose motor to humid, damp or extreme temperature conditions. 2. Do not drill into motor. 3. Do not cut the antenna and keep it clear from metal objects. 4. Do not allow children to play with this device. 5. If power cable or connector is damaged, do not use. 6. Ensure correct crown and drive adaptor are used. 7. Ensure power cable and aerial is clear and protected from moving parts. 8. Cable routed through walls shall be properly isolated. 9. Motor is to be mounted in horizontal position only. 10. Before installation, remove unnecessary cords and disable equipment not needed for powered operation. 11. Installation and programming to be performed by a qualified professional, use or modification outside the scope of this instruction may void warranty. Features Fields of Application Specifications Following data for reference Working temperature: -10°C ~ +50°C Input Voltage: USB 5V 1A / USB 5V 2A Radio Frequency: 433.925MHz Maximum Running Time: 6 minutes Model Rated Torque (N.m) Rated Speed (rpm) Rated Power (W) AMP25B - 0.7/340.7348 AMP25B -1.1/281.1288 Charging Instructions This motor has a built in Li-ion battery pack with integrated charge management. Max power input for recharging: 5V 2A. Before first use please charge motor for 6 hours. Using 5V charger (most phones charger is 5V ) . During operation, when the motor starts, the buzzer will beep 10 times, indicating a low-voltage alarm and needs to be charged. During operation, the voltage was detected to be too low, the battery was about to run out, the battery stopped running and needed to be recharged. Rechargeable Battery Blinking red: Low battery alert Blinking green: Charging is processing Solid green: Battery has finished charging. FCC Text - text 01 Add A zoom in on the charging port P1 Button Instructions P1 button Lithium Battery Switch LED light Micro-USB Port Add visual explanation of P1 - file 02 Sheer Roller Revolve Roman shades Do not dispose of in general waste. Please recycle batteries and damaged electrical products appropriately. SAFETY INSTRUCTIONS 1. Do not expose motor to humid, damp, or extreme temperature conditions. 2. Do not drill into motor. 3. Do not cut the antenna. Keep it clear from metal objects. 4. Do not allow children to play with this device. 5. If the power cable or connector is damaged, do not use. 6. Ensure the power cable and antenna are clear and protected from moving parts. 7. Cable routed through walls should be properly isolated. 8. Motor should be mounted in horizontal position only. 9. Before installation, remove unnecessary cords and disable equipment not needed for powered operation. Voltage 3V (CR2450) Radio Frequency 433.92 MHz Bi-directional Transmitting Power 10 milliwatt Operating Temperature 14°F to 122°F (-10°C to 50°C) RF Modulation FSK Lock Function Yes IP Rating IP20 Transmission Distance up to 200m (outdoor) SPECIFICATIONS Scan QR code to view additional BLISS ™ Automation Programming Guides Scan QR code to watch BLISS ™ Automation Programming Videos U.S. Radio Frequency FCC Compliance This device complies with Part 15 of the FCC Rules. Operation is subject to the following two conditions: (1) This device may not cause harmful interference, and (2) This device must accept any interference received, including interference that may cause undesired operation. This equipment has been tested and found to comply with the limits for a Class B digital device, pursuant to Part 15 of the FCC Rules. These limits are designed to provide reasonable protection against harmful interference in a residential installation. This equipment generates, uses, and can radiate radio frequency energy and, if not installed and used in accordance with the instructions, may cause harmful interference to radio communications. However, there is no guarantee that interference will not occur in a particular installation. If this equipment does cause harmful interference to radio or television reception, which can be determined by turning the equipment off and on, the user is encouraged to try to correct the interference by one or more of the following measures: • Reorient or relocate the receiving antenna. • Increase the separation between the equipment and receiver. • Connect the equipment into an outlet on a circuit different from that to which the receiver is connected. • Consult the dealer or an experienced radio/TV technician for help. Any Changes or modifications not expressly approved by the party responsible for compliance could void the user’s authority to operate the equipment. ISED RSS Warning: This device complies with Innovation, Science and Economic Development Canada license-exempt RSS standard(s). Operation is subject to the following two conditions: (1) this device may not cause interference, and (2) this device must accept any interference, including interference that may cause undesired operation of the device. Le présent appareil est conforme aux CNR d’ISED applicables aux appareils radio exempts de licence. L’exploitation est autorisée aux deux conditions suivantes: (1) l’appareil ne doit pas produire de brouillage, et (2) l’utilisateur de l’appareil doit accepter tout brouillage radioélectrique subi, même si le brouillage est susceptible d’en compromettre le fonctionnement. 7. ADDING A REMOTE CONTROL USING AN EXISTING REMOTE CONTROL a. On the current remote control, pres…

Text truncated - open the document above for the full version.

Turnils North America 1750 Satellite Blvd, Suite 100, Buford, Georgia, United States Date: 2023-05-06 Federal Communications Commission Authorization and Evaluation Division 1435 Oakland Mills Road Columbia, MD 21046 Ref: Attestation Statements Part 2.911(d) (5) (i) Filing SUBJECT: FCC Application for FCC ID: 2AU29ALATAAAARE To Whom It May Concern: Turnils North America certifies that the equipment for which authorization is sought is not “covered” equipment prohibited from receiving an equipment authorization pursuant to section 2.903 of the FCC rules. Sincerely, Signatory [Phoenix Lin, Senior Project Manager]

Turnils North America 1750 Satellite Blvd, Suite 100, Buford, Georgia, United States Date: 2023-05-06 Federal Communications Commission Authorization and Evaluation Division 1435 Oakland Mills Road Columbia, MD 21046 Ref: Attestation Statements Part 2.911(d) (5) (ii) Filing SUBJECT: FCC Application for FCC ID: 2AU29ALATAAAARE To Whom It May Concern: Turnils North America certifies that, as of the date of the filing of the application, the applicant is not identified on the Covered List as an entity producing “covered” equipment. Sincerely, Signatory [Phoenix Lin, Senior Project Manager]

Turnils North America 1750 Satellite Blvd, Suite 100, Buford, Georgia, United States Rev 1/26/2023 Date: 2023-02-09 Federal Communications Commission Authorization and Evaluation Division 1435 Oakland Mills Road Columbia, MD 21046 Ref: Attestation Statements Part 2.911(d) (7) Filing Grantee Code: 2AU29 Turnils North America certifies that, as of the date of the filing of the application, we designate ourselves as the U.S. agent for service of process. Turnils North America accepts to maintain an agent for no less than one year after the grantee has terminated all marketing and importation or the conclusion of any Commission-related proceeding involving the equipment. Designated U.S. Agent Information: FRN: 0028959575 Name: Turnils North America Address: 1750 Satellite Blvd, Suite 100, Buford, Georgia, United States Contact Person: Phoenix Lin Tel.: (770) 995-2222 3032 Email: [email protected] Signatory [Phoenix Lin, Senior Project Manager]

Turnils North America 1750 Satellite Blvd, Suite 100, Buford, Georgia, United States --------------------------------------------------------------------------------------------------------------------- Supplier’s Declaration Of Conformity for the FCC SDoC Procedure The following Equipment adapt FCC SDoC Procedure according to FCC part 2.906 : Product Name: Remote Brand Name: -- Model Number: 16C-Combo Remote, 15C-Remote Report Number: WTN22X07151266W002 It’s herewith confirmed to comply with the requirements of FCC Part 15 Rules. Operation is subject to the following two conditions: (1) This device may not cause harmful interference, and (2) This device must accept any interference received, including interference that may cause undesired operation. It is understood that each unit marketed is identical to the device as tested, and any changes to the device that could adversely affect the emission characteristics will require retest. The following importer / responsible party in United States: Company Name: Turnils North America Company Address: 1750 Satellite Blvd, Suite 100, Buford, Georgia, United States Telephone: 770-995-2222-3032 Fax: 770-995-2210 Person is responsible for marking this declaration: Phoenix Lin Name (Full name ) Project Manager Position / Title 2023-05-06 Legal SignatureDate

TurnilsNorth America 1750SatelliteBlvd,Suite100,Buford,Georgia,UnitedStates --------------------------------------------------------------------------------------------------------------------- Date: 2023-05-06 FederalCommunicationsCommission Authorizationand EvaluationDivision 7435 OaklandMills Road Columbia,MD 21046 FCC ID: 2AU29ALATAAAARE ConfidentialityRequest To whom it may concern, Pursuantto Sections0.457 and 0.459 of the Commission’s Rules,we herebyrequestconfidential treatmentof the informationaccompanyingthis applicationas outlinedbelow: ☒Block Diagram ☐Tune-UpInformation ☒ OperationalDescription ☐ SecurityInformation ☒Schematics☐SoftwareDefinedRadio (SDR) Information ☐ Parts List The abovematerialscontaintrade secretsand proprietaryinformationnot customarilyreleasedto the public.The public disclosureof these materialsmay be harmfulto the applicantand provide unjustifiedbenefitsto its competitors. The applicantunderstandsthat pursuantto Section0.457 of the Rules,disclosureof this applicationand all accompanyingdocumentationwill not be made beforethe date of the Grant for this application. Sincerely, TurnilsNorth America ------------------------------- PhoenixLin/ProjectManager

Turnils North America 1750 Satellite Blvd, Suite 100, Buford, Georgia, United States -------------------------------------------------------------------------------- (FCC ID ： 2AU29ALATAAAARE) POWER OF ATTORNEY DATE: 2023-05-06 Federal Communications Commission Authorization and Evaluation Division 7435 Oakland Mills Road Columbia, MD 21046 To Whom It May Concern: We, the undersigned, hereby authorize Waltek Testing Group (Shenzhen) Co., Ltd. Jandy So on our behalf, to apply to the Federal Communications Commission on our equipment. Any and all acts carried out by Waltek Testing Group (Shenzhen) Co., Ltd. Jandy So on our behalf shall have the same effect as acts of our own. This is to advise that we are in full compliance with the Anti-Drug Abuse Act. We, Turnils North America are not subject to a denial of federal benefits pursuant to Section 5301 of the Anti-Drug Act of 1988, 21 USC853a, and no party to the application is subject to a denial of federal benefits pursuant to that section. Sincerely, Turnils North America ---------------------------- Phoenix Lin /Project Manager

Reference No.: WTN22X07151266W001 Page 2 of 11 Waltek Testing Group (Shenzhen) Co., Ltd. Http://www.waltek.com.cn EXHIBIT 2 - EUT EXTERNAL PHOTOGRAPHS EUT View 1 EUT View 2 Reference No.: WTN22X07151266W001 Page 3 of 11 Waltek Testing Group (Shenzhen) Co., Ltd. Http://www.waltek.com.cn EUT View 3 EUT View 4 Reference No.: WTN22X07151266W001 Page 4 of 11 Waltek Testing Group (Shenzhen) Co., Ltd. Http://www.waltek.com.cn EUT View 5 EUT View 6 Reference No.: WTN22X07151266W001 Page 5 of 11 Waltek Testing Group (Shenzhen) Co., Ltd. Http://www.waltek.com.cn EUT View 7

Reference No.: WTN22X07151266W001 Page 1 of 11 Waltek Testing Group (Shenzhen) Co., Ltd. Http://www.waltek.com.cn ANNEX EXHIBIT 1 - PRODUCT LABELING Proposed FCC ID Label Format Specifications: The label shall be securely affixed to a permanently attached part of the device, in a location where it is visible or easily accessible to the user, and shall not be readily detachable. The label shall be sufficiently durable to remain fully legible and intact on the device in all normal conditions of use throughout the device’s expected lifetime. Proposed Label Location on EUT FCC ID Label Location

Reference No.: WTN22X07151266W001 Page 6 of 11 Waltek Testing Group (Shenzhen) Co., Ltd. Http://www.waltek.com.cn EXHIBIT 3 - EUT INTERNAL PHOTOGRAPHS EUT Housing and Board View 1 EUT Housing and Board View 2 Reference No.: WTN22X07151266W001 Page 7 of 11 Waltek Testing Group (Shenzhen) Co., Ltd. Http://www.waltek.com.cn Solder Board-Component View 1 Solder Board-Component View 2 Reference No.: WTN22X07151266W001 Page 8 of 11 Waltek Testing Group (Shenzhen) Co., Ltd. Http://www.waltek.com.cn Solder Board-Component View 3 Antenna View

1. RF Exposure Requirements 1.1 General Information Client Information Applicant: Turnils North America Address of applicant: 1750 Satellite Blvd,Suite 100,Buford GA 30518 Manufacturer: Turnils North America Address of manufacturer: 1750 Satellite Blvd,Suite 100,Buford GA 30518 General Description of EUT: Product Name: Remote Trade Name: / Model No.: 16C-Combo Remote Adding Model(s): 15C-Remote Rated Voltage: Battery DC 1.5*2V Power Adaptor : / FCC ID: 2AU29ALATAAAARE Equipment Type: Portable device Technical Characteristics of EUT: Frequency Range: 433.925 MHz Max. Field Strength: 433.925MHz: 78.25dBuV/m(3m) Data Rate: / Modulation: FSK Antenna Type: PCB Antenna Antenna Gain: 0dBi 1.2 RF Exposure Exemption According to §1.1307(b)(3) and KDB 447498 D04 Interim General RF Exposure Guidance v01, system operating under the provisions of this section shall be operating in a manner that the public is not exposed to radio frequency energy level in excess limit for maximum permissible exposure. Option A: FCC Rule Part 1.1307 (b)(3)(i)(A):The available maximum time-averaged power is no more than 1mW, regardless of separation distance. Option B: FCC Rule Part 1.1307 (b)(3)(i)(B): The available maximum time-averaged power or effective radiated power (ERP), whichever is greater, is less than or equal to the threshold P th (mW) described in the following formula. P th is given by: Option C: FCC Rule Part 1.1307 (b)(3)(i)(C): The minimum separation distance (R in meters) from the body of a nearby person for the frequency (f in MHz) at which the source operates, the ERP (watts) is no more than the calculated value prescribed for that frequency. R must be at least λ/2π, where λ is the free-space operating wavelength in meters. Single RF Sources Subject to Routine Environmental Evaluation RF Source frequency (MHz) Threshold ERP (watts) 0.3-1.34 1,920 R 2 1.34-30 3,450 R 2 /f 2 30-300 3.83 R 2 300-1,500 0.0128 R 2 f 1,500-100,000 19.2R 2 For Multiple RF sources: FCC Rule Part 1.1307(b)(3)(ii): (A) The available maximum time-averaged power of each source is no more than 1 mW and there is a separation distance of two centimeters between any portion of a radiating structure operating and the nearest portion of any other radiating structure in the same device, except if the sum of multiple sources is less than 1 mW during the time-averaging period, in which case they may be treated as a single source (separation is not required). (B) In the case of fixed RF sources operating in the same time-averaging period, or of multiple mobile or portable RF sources within a device operating in the same time averaging period, if the sum of the fractional contributions to the applicable thresholds is less than or equal to 1 as indicated in the following equation. 1.3 Calculated Result Radio Access Technology Prediction Frequency Max. Field Strength Antenna Gain Output Power Tune-Up Power ERP (MHz) (dBuV/m) (dBi) (dBm) (dBm) (dBm) SRD 433.925 78.25 0 -17.01 -17.00 -19.15 Frequency Option Min. Distance Max. Power Exposure Limit Ratio Result (MHz) (cm) (dBm) (mW) (mW) Pass/Fail 433.925 A -- -17.00 0.02 1 0.02 Pass Note: 1. EIRP= E-104.8+20logD; Output Power=EIRP- Antenna Gain; ERP=EIRP-2.15dB 2. Option A, B and C refers as clause 1.2. 3. For option B, Max (time-averaged power, effective radiated power (ERP)) converts to Max. Power. For option C, ERP converts to Max. Power; 4. For option B, P th (mW) converts to Exposure Limit (mW); For option C, ERP (W) converts to Exposure Limit (mW). 5. Ratio= Tune-Up ERP (mW)/ Exposure Limit (mW) Mode for Simultaneous Multi-band Transmission: Radio Access Technology Ratio 1 Ratio 2 Ratio 3 Simultaneous Ratio Limit Result Pass/Fail / / / / / / / Result: Pass

Unit:mm

Waltek Testing Group (Shenzhen) Co., Ltd. Http://www.waltek.com.cn Page 1 of 24 TEST REPORT Reference No. .................... : WTN22X07151266W001 FCC ID ................................ : 2AU29ALATAAAARE Applicant ........................... : Turnils North America Address ............................. : 1750 Satellite Blvd,Suite 100,Buford GA 30518 Manufacturer ..................... : The same as Applicant Address ............................. : The same as Applicant Product Name ................... : Remote Model No... ......................... : 16C-Combo Remote Standards .......................... : FCC Part 15.231 Date of Receipt sample .... : 2022-07-25 Date of Test........................ : 2022-07-25 to 2022-08-23 Date of Issue ..................... : 2022-08-23 Test Report Form No. ....... : WTX_Part 15_231W Test Result ......................... : Pass Remarks: The results shown in this test report refer only to the sample(s) tested, this test report cannot be reproduced, except in full, without prior written permission of the company. The report would be invalid without specific stamp of test institute and the signatures of approver. Prepared By: Waltek Testing Group (Shenzhen) Co., Ltd. Address: 1/F., Room 101, Building 1, Hongwei Industrial Park, Liuxian 2nd Road, Block 70 Bao'an District, Shenzhen, Guangdong, China Tel.: +86-755-33663308 Fax.: +86-755-33663309 Email: [email protected] Tested by: Approved by: Jack Huang Silin Chen Reference No.: WTN22X07151266W001 Waltek Testing Group (Shenzhen) Co., Ltd. Http://www.waltek.com.cn Page 2 of 24 TABLE OF CONTENTS 1. GENERAL INFORMATION ................................................................................................................................... 4 1.1 PRODUCT DESCRIPTION FOR EQUIPMENT UNDER TEST (EUT) ............................................................................... 4 1.2 TEST STANDARDS ................................................................................................................................................... 5 1.3 TEST METHODOLOGY ............................................................................................................................................. 5 1.4 TEST FACILITY ....................................................................................................................................................... 5 1.5 EUT SETUP AND TEST MODE ................................................................................................................................. 6 1.6 MEASUREMENT UNCERTAINTY .............................................................................................................................. 7 1.7 TEST EQUIPMENT LIST AND DETAILS ..................................................................................................................... 8 2. SUMMARY OF TEST RESULTS ......................................................................................................................... 10 3. ANTENNA REQUIREMENT ................................................................................................................................ 11 3.1 STANDARD APPLICABLE ....................................................................................................................................... 11 3.2 TEST RESULT........................................................................................................................................................ 11 4. RADIATED EMISSIONS ....................................................................................................................................... 12 4.1 STANDARD APPLICABLE ....................................................................................................................................... 12 4.2 TEST PROCEDURE ................................................................................................................................................. 13 4.3 CORRECTED AMPLITUDE & MARGIN CALCULATION ............................................................................................ 14 4.4 SUMMARY OF TEST RESULTS/PLOTS .................................................................................................................... 14 5. 20DB BANDWIDTH ............................................................................................................................................... 17 5.1 STANDARD APPLICABLE ....................................................................................................................................... 17 5.1 TEST PROCEDURE ................................................................................................................................................. 17 5.2 SUMMARY OF TEST RESULTS/PLOTS .................................................................................................................... 17 6. TRANSMISSION TIME ......................................................................................................................................... 19 6.1 STANDARD APPLICABLE ....................................................................................................................................... 19 6.2 TEST PROCEDURE ................................................................................................................................................. 19 6.3 SUMMARY OF TEST RESULTS/PLOTS .................................................................................................................... 19 7. DUTY CYCLE ......................................................................................................................................................... 21 7.1 STANDARD APPLICABLE ....................................................................................................................................... 21 7.2 TEST PROCEDURE ................................................…

Text truncated - open the document above for the full version.

Reference No.: WTN22X07151266W001 Page 9 of 11 Waltek Testing Group (Shenzhen) Co., Ltd. Http://www.waltek.com.cn EXHIBIT 4 - TEST SETUP PHOTOGRAPHS Radiation Emission Test Setup (Below 30MHz) Radiation Emission Test Setup (30MHz to 1GHz) Reference No.: WTN22X07151266W001 Page 10 of 11 Waltek Testing Group (Shenzhen) Co., Ltd. Http://www.waltek.com.cn Radiation Emission Test Setup (1GHz to 18GHz) Radiation Emission Test Setup (Above 18GHz) Reference No.: WTN22X07151266W001 Page 11 of 11 Waltek Testing Group (Shenzhen) Co., Ltd. Http://www.waltek.com.cn ***** END OF REPORT *****