2AU29AMP15WSCut-in Wall Switch

Issues Possible Causes Solution Battery in motor is depleted Recharge with compatible AC adaptor and check connection and positioning of solar PV panel Insufficient charging from Solar PV Panel Check connection and orientation of solar PV panel Wall switch battery is discharged Replace battery Battery is inserted incorrectly into wall switch Check battery polarity The motor has no response Radio interference / shielding Ensure wall switch and the antenna on the motor are positioned away from metal objects Receiver distance is too far from wall switch Move wall switch to a closer position Power failure Check power supply to motor is connected and active Incorrect wiring Check that wiring is connected correctly (refer to motor installation instructions) Motor beeps 10 times when in use Battery voltage is low / PV (solar panel issue) Recharge with AC adapter or check connection and positioning of solar PV panelAlways reserve an individual channel for programming functionsSYSTEM BEST PRACTICE - Provide an extra 15 channel remote in your multi-motor projects that provides individual control for each motor for programming purposesPlace all other motors into sleep mode (Press “P1” button (about 6 sec) on the motor head until motor jog x2 and beep x2). Do not dispose of in general waste.Please recycle batteries and damaged electrical products appropriately. Roller Cellular/Honeycomb Standard Cellular/Honeycomb Skylight Sheer Banded Tilt-Only Horizontal Narrow Width Roman Cannot program a single motor (multiple motors respond) Multiple motors are paired to the same channel. Settings Steps 1 Pairing P1 (hold down for 2s) > Stop (hold down for 2s) 2 Switch Rotating Direction Up + Down (hold down for 2s) 3 Setting Upper & Lower Limits4 Add / Remove Favorite Position P2 > Stop > Stop 5 Roller Mode & Sheer Mode Switch Up + Down (hold down for 5s) > Stop 6 Adjust Limits7 Pair / Unpair Additional Emitter P2 (existing) > P2 (existing) > P2 (new) 8 Speed Regulation Upper Limit: Up (hold down for 2s) > Up + Stop (hold down for 2s) Upper Limit: Up + Stop (hold down for 5s) > Up or Down > Up + Stop (hold down for 2s) Acceleration: P2 > Up > Up Lower Limit: Down (hold down for 2s) > Down + Stop (hold down for 2s) Lower Limit: Down + Stop (hold down for 5s) > Up or Down > Down + Stop (hold down for 2s) Deceleration: P2 > Down > Down AMP ™ Wall Switch Declarations Fields of Application Quick Index Safety Instructions Troubleshooting Button InstructionsReplace/Install BatteryAdvanced Setting - Disable Limit Setting 1. Do not expose motor to humid, damp, or extreme temperature conditions.2. Do not drill into motor.3. Do not cut the antenna. Keep it clear from metal objects.4. Do not allow children to play with this device.5. If the power cable or connector is damaged, do not use.6. Ensure the correct crown and drive adaptor are used.7. Ensure the power cable and aerial is clear and protected from moving parts.8. Cable routed through walls should be properly isolated.9. Motor is to be mounted in horizontal position only.10. Before installation, remove unnecessary cords and disable equipment not needed for powered operation.11. Installation and programming should be performed by a qualified professional. Use or modification outside the scope of these instructions may void warranty. U.S. Radio Frequency FCC ComplianceThis device complies with Part 15 of the FCC Rules. Operation is subject to the following two conditions:(1) This device may not cause harmful interference, and(2) This device must accept any interference received, including interference that may cause undesired operation.This equipment has been tested and found to comply with the limits for a Class B digital device, pursuant to Part 15 of the FCC Rules. These limits are designed to provide reasonable protection against harmful interference in a residential installation. This equipment generates, uses, and can radiate radio frequency energy and, if not installed and used in accordance with the instructions, may cause harmful interference to radio communications. However, there is no guarantee that interference will not occur in a particular installation. If this equipment does cause harmful interference to radio or television reception, which can be determined by turning the equipment off and on, the user is encouraged to try to correct the interference by one or more of the following measures:• Reorient or relocate the receiving antenna.• Increase the separation between the equipment and receiver.• Connect the equipment into an outlet on a circuit different from that to which the receiver is connected.• Consult the dealer or an experienced radio/TV technician for help.Any Changes or modifications not expressly approved by the party responsible for compliance could void the user’s authority to operate the equipment. ISED RSS Warning:This device complies with Innovation, Science and Economic Development Canada licence-exempt RSS standard(s). Operation is subject to the following two conditions: (1) this device may not cause interference, and (2) this device must accept any interference, including interference that may cause undesired operation of the device. Le présent appareil est conforme aux CNR d’ISED applicables aux appareils radio exempts de licence. L’exploitation est autorisée aux deux conditions suivantes: (1) l’appareil ne doit pas produire de brouillage, et (2) l’utilisateur de l’appareil doit accepter tout brouillage radioélectrique subi, même si le brouillage est susceptible d’en compromettre le fonctionnement. AMPTILT AMP25B / AMP28B / AMP35B / AMP25BDC AMPCEL P1 Button LED light P1 button Lithium Battery Switch Power lineSignal line P1 Button Voltage 3V (AAA battery x 2) Radio Frequency 433.92 MHz Bi-directional Transmitting Power 10 milliwatt Operating Temperature 14°F to 122°F (-10°C to 50°C) RF Modulation FSK Lock Function Yes IP Rating IP20 Transmission Distance up to 200m (outdoor) Specifications a. Press and hold “Stop“ button more t…

Text truncated - open the document above for the full version.

FC C Confidential Authorization Date: 2020-10-16 FEDERAL COMMUNICATIONS COMMISSIONS Authorization and Evaluation Division 7435 Oakland Mills Road Columbia, MD 21046 Subject: Confidentiality Request regarding application for certification of FCC ID: 2AU29AMP15WS To whom it may concern, In accordance with Sections 0.457 and 0.459 of the Commission’s Rules, Turnils North America hereby requests long-term confidential treatment of information accompanying this application as outlined below: Block Diagram Schematics Operation Description The above materials contain proprietary and confidential information not customarily released to the public. The public disclosure of these materials provides unjustified benefits to its competitors in the market. Sincerely, Signature: Typed or Printed Name: Phoenix Lin Title: Project Manager [email protected]

FCC Authorization Signature: Typed or Printed Name: Phoenix Lin Title: Project Manager [email protected] QA-FR-170-B (Shenzhen)Co,Lt to act on its behalf in all matters relating to application for Equipment authorization, including the signing of all documents relating to these matters. All acts carried out by Bay Area Compliance Laboratories Corp. on our behalf shall have the same effect as our own action. We, the undersigned, hereby certify that we are not subject to a denial of federal benefits, that includes FCC benefits, pursuant to Section 5301 of the Anti-Drug Abuse Act of 1988, 21 U.S.C. 862. This authorization is valid until further written notice from the applicant. Sincerely, Date: 2020-10-16 FEDERAL COMMUNICATIONS COMMISSION Authorization and Evaluation Division 7435 Oakland Mills Road Columbia, MD 21046 Subject: Agent Authorization FCC ID: 2AU29AMP15WS To whom it mayconcern: We,TurnilsNorth America, the undersigned, hereby authorizeJandy So,Waltek Testing Group

Reference N Waltek Tes http://www EXHIBI EUT EUT No.: WTN20X sting Group w.semtest.co T 1 - EUT View 1 View 2 X09064529W (Shenzhen) m.cn T EXTER W-1 Co., Ltd. RNAL PH ANNEX HOTOGR APHS Reference N Waltek Tes http://www EUT EUT No.: WTN20X sting Group w.semtest.co View 3 View 4 X09064529W (Shenzhen) m.cn W-1 Co., Ltd. Reference N Waltek Tes http://www EUT EUT No.: WTN20X sting Group w.semtest.co View 5 View 6 X09064529W (Shenzhen) m.cn W-1 Co., Ltd. Reference N Waltek Tes http://www EUT No.: WTN20X sting Group w.semtest.co View 7 X09064529W (Shenzhen) m.cn W-1 Co., Ltd.

Waltek Tes http://www EXHIBI Proposed Specificatio n it is visible durable to r expected lif e Proposed sting Group w.semtest.co T - PROD FCC ID La ns: The label or easily acc emain fully l etime. Label Loca (Shenzhen) m.cn DUCT LA abel Forma shall be secu cessible to th legible and in ation on EU Co., Ltd. ABELING at urely affixed t he user, and ntact on the UT FCC G to a permane shall not be device in al l ID Label Lo ently attached readily detac l normal cond cation d part of the d chable. The l ditions of use device, in a lo label shall be e throughout ocation where e sufficiently t the device’s e y s

Reference N Waltek Tes http://www EXHIBI EUT Housi V i EUT Housi V i No.: WTN20X sting Group w.semtest.co T 2 - EUT ng and Boar iew 1 ng and Boar iew 2 X09064529W (Shenzhen) m.cn T INTER rd rd W-1 Co., Ltd. NAL PHO OTOGRA APHS Reference N Waltek Tes http://www EUT Housi Vi So Board-Com No.: WTN20X sting Group w.semtest.co ng and Boar iew 3 older mponent View 1 X09064529W (Shenzhen) m.cn rd w W-1 Co., Ltd. Reference N Waltek Tes http://www S o Board-Com Anten No.: WTN20X sting Group w.semtest.co older mponent View 2 nna View X09064529W (Shenzhen) m.cn w W-1 Co., Ltd.

Waltek Testing Group (Shenzhen) Co., Ltd. http://www.semtest.com.cn Page 1 of 23 TEST REPORT Reference No. .................... : WTN20X09064529W-1 FCC ID ................................ : 2AU29AMP15WS Applicant ........................... : Turnils North America Address ............................. : 1750 Satellite Blvd, Suite 100, Buford GA 30518 Product Name ................... : Cut-in Wall Switch Test Model. ........................ : 15C-Wall Switch Standards .......................... : FCC Part 15.231 Date of Receipt sample .... : Sept.09, 2020 Date of Test........................ : Sept.09, 2020 to Sept.23, 2020 Date of Issue ..................... : Sept.23, 2020 Test Result ......................... : Pass Remarks: The results shown in this test report refer only to the sample(s) tested, this test report cannot be reproduced, except in full, without prior written permission of the company. The report would be invalid without specific stamp of test institute and the signatures of compiler and approver. Prepared By: Waltek Testing Group (Shenzhen) Co., Ltd. Address: 1/F., Room 101, Building 1, Hongwei Industrial Park, Liuxian 2nd Road, Block 70 Bao'an District, Shenzhen, Guangdong, China Tel.: +86-755-33663308 Fax.: +86-755-33663309 Tested by: Reviewed By: Approved & Authorized By: Mike Shi / Project Engineer Lion Cai / RF Manager Silin Chen / Manager Reference No.: WTN20X09064529W-1 Page 2 of 23 Waltek Testing Group (Shenzhen) Co., Ltd. http://www.semtest.com.cn TABLE OF CONTENTS 1. GENERAL INFORMATION ................................................................................................................................... 4 1.1 PRODUCT DESCRIPTION FOR EQUIPMENT UNDER TEST (EUT) ............................................................................... 4 1.2 TEST STANDARDS ................................................................................................................................................... 5 1.3 TEST METHODOLOGY ............................................................................................................................................. 5 1.4 TEST FACILITY ....................................................................................................................................................... 5 1.5 EUT SETUP AND TEST MODE ................................................................................................................................. 6 1.6 MEASUREMENT UNCERTAINTY .............................................................................................................................. 6 1.7 TEST EQUIPMENT LIST AND DETAILS ..................................................................................................................... 7 2. SUMMARY OF TEST RESULTS ........................................................................................................................... 8 3. ANTENNA REQUIREMENT .................................................................................................................................. 9 3.1 STANDARD APPLICABLE ......................................................................................................................................... 9 3.2 TEST RESULT.......................................................................................................................................................... 9 4. RADIATED EMISSIONS ....................................................................................................................................... 10 4.1 STANDARD APPLICABLE ....................................................................................................................................... 10 4.2 TEST PROCEDURE ................................................................................................................................................. 11 4.3 CORRECTED AMPLITUDE & MARGIN CALCULATION ............................................................................................ 12 4.4 SUMMARY OF TEST RESULTS/PLOTS .................................................................................................................... 12 5. 20DB BANDWIDTH ............................................................................................................................................... 16 5.1 STANDARD APPLICABLE ....................................................................................................................................... 16 5.1 TEST PROCEDURE ................................................................................................................................................. 16 5.2 SUMMARY OF TEST RESULTS/PLOTS .................................................................................................................... 16 6. TRANSMISSION TIME ......................................................................................................................................... 18 6.1 STANDARD APPLICABLE ....................................................................................................................................... 18 6.2 TEST PROCEDURE ................................................................................................................................................. 18 6.3 SUMMARY OF TEST RESULTS/PLOTS .................................................................................................................... 18 7. DUTY CYCLE ......................................................................................................................................................... 20 7.1 STANDARD APPLICABLE ....................................................................................................................................... 20 7.2 TEST PROCEDURE .................................................................................................................................…

Text truncated - open the document above for the full version.

Reference N Waltek Tes http://www EXHIBI Radiation E Setup (Belo Radiation E Setup (30M No.: WTN20X sting Group w.semtest.co T 3 - TES Emission Te ow 30MHz) Emission Te MHz to 1GHz X09064529W (Shenzhen) m.cn ST SETUP est est z) W-1 Co., Ltd. P PHOTO OGRAPH HS Reference N Waltek Tes http://www Radiation E Setup (1GH No.: WTN20X sting Group w.semtest.co Emission Te Hz to 18GHz) X09064529W (Shenzhen) m.cn est ) W-1 Co., Ltd.