2AU2C-F1CAMERAF1 Camera SMART PET FEEDER

FAQ 6. Where is the SD card slot, what is the capacity and pictures and videos storage position? To access t he SD card slot, take out internel food container, the slot 1s located inside behind the control panel. The SD card slot supports up to 32GB, and the storage position (SD card or Phone) can be assigned on the phone 7. What kind of network does the pet feeder require? The network have to conform tow咑802.llbgn protocol. No requirements on the phone signal as long as it can connect to the network 8. Upgrade management. 1). APP upgrade: The APP will 「em ind users to upgrade each time the use「log ,n the APP. Just upgrade the APP according to the notes 2). Firmware upgrade: More settings分Device management今Fireware Ver分 Upgrade To get a bette「user experience, please update the software and fireware in time. (It will takes about 8 minu tes to upgrade the software. Don't cut off the power or disconnect the network during upg「ade.) 9. About using P etwant without power source. Petwant can be powe「ed by "D" cell battery, but only works fo「manual o「 sc heduled feeding, camera and audio functions will be disabled when using " D" cell battery to save power. FCC STATEMENT : This device complies with Part 15 of the FCC Rules. Operation is subject to the following two conditions: (1)This device may not cause harmful interference, and (2)This device must accept any interference received, including interference that may cause undesired operation. Warning: Changes or modifications not expressly approved by the party resp onsible for compliance could void the user's authority to operate the equipment. NOTE: This equipment has been tested and found to comply with the limit s for a Class B digital device, pursuant to Part 15 of the FCC Rules. These limits are designed to provide reasonable protection against harmful interference in a residential installation. This equipment generates uses and can radiate radio frequency energy and, if not installed and used in accordance with the instructions, may cause harmful interference to radio communications. How ever, there is no guarantee that interference will not occur in a particular installation. If this equipment does cause harmful interference to radio or television reception, which can be determined by turning the equipment off and on, the user is encouraged to try to correct the interference by one or more of the following measures: Reorient or relocate the receiving antenna. Increase the separation between the equipment and receiver. Connect the eq uipment into an outlet on a circuit different from that to which the receiver is connected.Consult the dealer or an experienced radio/TV technician for help FCC Radiation Exposure Statement : This equipment complies with FCC radiation exposure limits set forth for an uncontrolled environment. This equipment should be installed and operated with minimum distance 20cm between the radiator & your body.

FCC ID: 2AU2C-F1CAMERA

Label Location On EUT Label Product Name: F1 Camera SMART PET FEEDER Model Number:F1 Camera FCC ID: 2AU2C-F1CAMERA This device complies with Part 15 of the FCC Rules. Operation is subject to the following two conditions: (1)This device may not cause harmful interference, and (2)This device must accept any interference received, including interference that may cause undesired operation.

FCC ID: 2AU2C-F1CAMERA ANT

version01 Shenzhen Qianhai Runway Technology Co., LTD Declaration concerning Antenna Specification It is hereby declared that the product Model No.: F1 Camera, F1 -C FCCID:2AU2C-F1CAMERA fulfills the requirement in FCC test relating to the antenna type. The device specified above confirms to the FCC recommendations for internal antenna type(s) described below: Model No. of antenna: F1 Camera Type of antenna:PIFA Antenna Wifi 2.4G: Gain of the antenna: 0 dBi Frequency range:802.11b/ g/ n(HT20) 2412-2462MHz The mounting of the antenna is fixed to the radio module and no other antenna should be used. Company name: Shenzhen Qianhai Runway Technology Co., LTD Address: Room 201, Block A, No.1, Qianwan Road 1, Qianhai Shenzhen Hong Kong Cooperation Zone, Shenzhen. City:Shenzhen ZIP / Postal code: Country:China Place: Shenzhen Date: 2020-04-15 Signature:

RF EXPOSURE EVALUATION According to FCC 1.1310: The criteria listed in the following table shall be used to evaluate the environment impact of human exposure to radio frequency(RF) Radiation as specified in §1.1307(b) FCC ID: 2AU2C-F1CAMERA EUT Specification EUTF1 Camera SMART PET FEEDER Frequency band (Operating) WLAN: 2.412GHz ~ 2.462GHz WLAN: 5.18GHz ~ 5.32GHz / 5.50GHz ~ 5.70GHz WLAN: 5.745GHz ~ 5825GHz Others: 2.402GHz~2.480GHz (BT4.2 BLE) Device category Portable (<20cm separation) Mobile (>20cm separation) Others ___ Exposure classificationOccupational/Controlled exposure (S = 5mW/cm2) General Population/Uncontrolled exposure (S=1mW/cm2) Antenna diversitySingle antenna Multiple antennas Tx diversity Rx diversity Tx/Rx diversity Max. output power13.75 dBm (0.0237W) Antenna gain (Max)0dBi Evaluation applied MPE Evaluation SAR Evaluation Limits for Maximum Permissible Exposure(MPE) Frequency Range(MHz) Electric Field Strength(V/m) Magnetic Field Strength(A/m) Power Density(mW/cm 2 ) Average Time (A) Limits for Occupational/Control Exposures 300-1500----F/3006 1500-100000----56 (B) Limits for General Population/Uncontrol Exposures 300-1500----F/15006 1500-100000----130 Friis transmission formula: Pd=(Pout*G)\(4*pi*R2) Where Pd= Power density in mW/cm 2 Pout=output power to antenna in Mw G= gain of antenna in linear scale Pi=3.1416 R= distance between observation point and center of the radiator in cm Pd the limit of MPE, 1mW/cm2. If we know the maximum gain of the antenna and total power input to the antenna, through the calculation, we will know the distance where the MPE limit is reached. Measurement Result Operating Mode Channel Frequency (MHz) Measured Power (dBm) Tune up tolerance (dBm) Max. Tune up Power (dBm) Antenna Gain (dBi) Power density at 20cm (mW/ cm 2 ) Power density Limits (mW/cm 2 ) 802.11b 241213.5913.59±114.5900.00571 243713.7513.75±114.7500.00591 246213.3113.31±114.3100.00541 802.11g 241212.5712.57±113.5700.00451 243712.7212.72±113.7200.00471 246212.0712.07±113.0700.00401 802.11n( 20) 241211.8811.88±112.8800.00391 243712.4712.47±113.4700.00441 246211.7311.73±112.7300.00371

Report No.: 18220WC00023701FCC ID: 2AU2C-F1CAMERAPage 1 of 66 Code:AB-RF-05-a FCC TEST REPORT Client Name: Shenzhen Qianhai Runway Technology Co., LTD Address: Room 201, Block A, No.1, Qianwan Road 1, Qianhai Shenzhen Hong Kong Cooperation Zone, Shenzhen. Product Name: F1 Camera SMART PET FEEDER Date: Apr. 16, 2020 Shenzhen Anbotek Compliance Laboratory Limited Report No.: 18220WC00023701FCC ID: 2AU2C-F1CAMERAPage 2 of 66 Code:AB-RF-05-a Contents 1. General Information ............................................................................................................................................... 5 1.1. Client Information ....................................................................................................................................... 5 1.2. Description of Device (EUT) ..................................................................................................................... 5 1.3. Auxiliary Equipment Used During Test ................................................................................................... 6 1.4. Description of Test Modes ........................................................................................................................ 6 1.5. List of channels ........................................................................................................................................... 7 1.6. Description Of Test Setup ......................................................................................................................... 8 1.7. Test Equipment List .................................................................................................................................... 9 1.8. Measurement Uncertainty ....................................................................................................................... 10 1.9. Description of Test Facility ...................................................................................................................... 10 2. Summary of Test Results ................................................................................................................................... 11 3. Conducted Emission Test ................................................................................................................................... 12 3.1. Test Standard and Limit .......................................................................................................................... 12 3.2. Test Setup .................................................................................................................................................. 12 3.3. Test Procedure .......................................................................................................................................... 12 4. Radiation Spurious Emission and Band Edge ................................................................................................ 15 4.1. Test Standard and Limit .......................................................................................................................... 15 4.2. Test Setup .................................................................................................................................................. 15 4.3. Test Procedure .......................................................................................................................................... 16 4.4. Test Data .................................................................................................................................................... 17 5. Maximum Peak Output Power Test .................................................................................................................. 26 5.1. Test Standard and Limit .......................................................................................................................... 26 5.2. Test Setup .................................................................................................................................................. 26 5.3. Test Procedure .......................................................................................................................................... 26 5.4. Test Data .................................................................................................................................................... 26 6. 6DB Occupy Bandwidth Test ............................................................................................................................. 30 6.1. Test Standard and Limit .......................................................................................................................... 30 6.2. Test Setup .................................................................................................................................................. 30 6.3. Test Procedure ............................................................................................................................... ........... 30 6.4. Test Data .................................................................................................................................................... 30 7. Power Spectral Density Test .............................................................................................................................. 37 7.1. Test Standard and Limit .......................................................................................................................... 37 7.2. Test Setup .................................................................................................................................................. 37 7.3. Test Procedure .......................................................................................................................................... 37 7.4. Test Data ............................................................................................................…

Text truncated - open the document above for the full version.

FCC ID: 2AU2C-F1CAMERA Photo of PowerLine Conducted Emission Test Photo of Radiation Emission Test