2AVSB-CB-T10Wireless Charger

FCC Warning This device complies with part 15 of the FCC Rules. Operation is subject to the following two conditions: (1)This device may not cause harmful interference, and (2) this device must accept any interference received, including interference that may cause undesired operation. Any Changes or modifications not expressly approved by the party responsible for compliance could void the user's authority to operate the equipment. Note: This equipment has been tested and found to comply with the limits for a Class B digital device, pursuant to part 15 of the FCC Rules. These limits are designed to provide reasonable protection against harmful interference in a residential installation. This equipment generates uses and can radiate radiofrequency energy and, if not installed and used in accordance with the instructions, may cause harmful interference to radio communications. However, there is no guarantee that interference will not occur in a particular installation. If this equipment does cause harmful interference to radio or television reception, which can be determined by turning the equipment off and on, the user is encouraged to try to correct the interference by one or more of the following measures: -Reorient or relocate the receiving antenna. -Increase the separation between the equipment and receiver. -Connect the equipment into an outlet on a circuit different from that to which the receiver is connected. -Consult the dealer or an experienced radio/TV technician for help. The FCC certification of this device refers to RF exposure testing performed in typical operating conditions, where a person is no closer than 20 centimeters from the device surface at all times, except for non-repetitive patterns with transient time intervals in the order of a second. Only in the stated conditions, the device is shown to fully comply with the FCC RF Exposure requirements of KDB 447498.

- Shenzhen Mgctech Co.,Ltd. - Federal Communications Commission Authorization and Evaluation Division Equipment Authorization Branch 7435 Oakland Mills Road Columbia, MD 21046 8/30/2024 U.S. Agent Designation Shenzhen Mgctech Co.,Ltd. acknowledges their consent for the following contact located in the United States to act as their agent for service of process for the equipment for which authorization is sought (FCC ID: 2AVSB-CB- T10): Name and company of U.S. agent: UUX GROUP INC Physical U.S. address of agent: 36 South 18th Avenue, Suite A Brighton, CO USA 80601 FRN of U.S. agent: 0033701590 Email address of U.S. agent: [email protected] UUX GROUP INC acknowledges their obligation to accept service of process on behalf of Shenzhen Mgctech Co.,Ltd.. Shenzhen Mgctech Co.,Ltd. with the FRN 0029269446 accepts its obligation to maintain an agent for service of process in the United States for no less than one year after either the grantee has permanently terminated all marketing and importation of the applicable equipment within the U.S., or the conclusion of any Commission- related administrative or judicial proceeding involving the equipment, whichever is later. By signing this form, we confirm the above and that we are aware of the application requirements listed under § 2.911(d)(7). The information provided in this letter is based on the referenced rule parts of Title 47 of the CFR as well as KDB 986446 D01. An expiration date for this letter does not exist. In case the U.S. agent changes, the grantee is obligated to notify the FCC within 30 days via the granting TCB. Sincerely, Signature Cici Huang Overseas Sales Manager Shenzhen Mgctech Co.,Ltd. Signature Jack Fu Manager UUX GROUP INC 48_[model] US_Agent_2.911(d)(7) - U, V05

Page 1 of 7 FCC ID: 2AVSB-CB-T10 Guangdong Asia Hongke Test Technology Limited B1/F, Building 11, Junfeng Industrial Park, Chongqing Road, Heping Community, Fuhai Street, Bao'an District, Shenzhen, Guangdong, China. EUT Constructional Details External EUT Photo Photo 1 Photo 2 Page 2 of 7 FCC ID: 2AVSB-CB-T10 Guangdong Asia Hongke Test Technology Limited B1/F, Building 11, Junfeng Industrial Park, Chongqing Road, Heping Community, Fuhai Street, Bao'an District, Shenzhen, Guangdong, China. Photo 3 Photo 4 Page 3 of 7 FCC ID: 2AVSB-CB-T10 Guangdong Asia Hongke Test Technology Limited B1/F, Building 11, Junfeng Industrial Park, Chongqing Road, Heping Community, Fuhai Street, Bao'an District, Shenzhen, Guangdong, China. Photo 5 Photo 6 Page 4 of 7 FCC ID: 2AVSB-CB-T10 Guangdong Asia Hongke Test Technology Limited B1/F, Building 11, Junfeng Industrial Park, Chongqing Road, Heping Community, Fuhai Street, Bao'an District, Shenzhen, Guangdong, China. Photo 7 Photo 8 Page 5 of 7 FCC ID: 2AVSB-CB-T10 Guangdong Asia Hongke Test Technology Limited B1/F, Building 11, Junfeng Industrial Park, Chongqing Road, Heping Community, Fuhai Street, Bao'an District, Shenzhen, Guangdong, China. Photo 9 Photo 10 Page 6 of 7 FCC ID: 2AVSB-CB-T10 Guangdong Asia Hongke Test Technology Limited B1/F, Building 11, Junfeng Industrial Park, Chongqing Road, Heping Community, Fuhai Street, Bao'an District, Shenzhen, Guangdong, China. Photo 11 Photo 12 Page 7 of 7 FCC ID: 2AVSB-CB-T10 Guangdong Asia Hongke Test Technology Limited B1/F, Building 11, Junfeng Industrial Park, Chongqing Road, Heping Community, Fuhai Street, Bao'an District, Shenzhen, Guangdong, China. Photo 13 ---The End---

Label Size: L55mm * W30mm 1. The label is silk-screen on the sample Wireless Charger Model Name: CBT-10 FCC ID: 2AVSB-CB-T10 L W

Page 1 of 17 FCC ID: 2AVSB-CB-T10 Guangdong Asia Hongke Test Technology Limited B1/F, Building 11, Junfeng Industrial Park, Chongqing Road, Heping Community, Fuhai Street, Bao'an District, Shenzhen, Guangdong, China. EUT Constructional Details Internal EUT Photo Photo 1 Photo 2 Phone Coil Page 2 of 17 FCC ID: 2AVSB-CB-T10 Guangdong Asia Hongke Test Technology Limited B1/F, Building 11, Junfeng Industrial Park, Chongqing Road, Heping Community, Fuhai Street, Bao'an District, Shenzhen, Guangdong, China. Photo 3 Photo 4 Page 3 of 17 FCC ID: 2AVSB-CB-T10 Guangdong Asia Hongke Test Technology Limited B1/F, Building 11, Junfeng Industrial Park, Chongqing Road, Heping Community, Fuhai Street, Bao'an District, Shenzhen, Guangdong, China. Photo 5 Photo 6 Page 4 of 17 FCC ID: 2AVSB-CB-T10 Guangdong Asia Hongke Test Technology Limited B1/F, Building 11, Junfeng Industrial Park, Chongqing Road, Heping Community, Fuhai Street, Bao'an District, Shenzhen, Guangdong, China. Photo 7 Photo 8 Page 5 of 17 FCC ID: 2AVSB-CB-T10 Guangdong Asia Hongke Test Technology Limited B1/F, Building 11, Junfeng Industrial Park, Chongqing Road, Heping Community, Fuhai Street, Bao'an District, Shenzhen, Guangdong, China. Photo 9 Photo 10 Page 6 of 17 FCC ID: 2AVSB-CB-T10 Guangdong Asia Hongke Test Technology Limited B1/F, Building 11, Junfeng Industrial Park, Chongqing Road, Heping Community, Fuhai Street, Bao'an District, Shenzhen, Guangdong, China. Photo 11 Photo 12 Page 7 of 17 FCC ID: 2AVSB-CB-T10 Guangdong Asia Hongke Test Technology Limited B1/F, Building 11, Junfeng Industrial Park, Chongqing Road, Heping Community, Fuhai Street, Bao'an District, Shenzhen, Guangdong, China. Photo 13 Photo 14 Page 8 of 17 FCC ID: 2AVSB-CB-T10 Guangdong Asia Hongke Test Technology Limited B1/F, Building 11, Junfeng Industrial Park, Chongqing Road, Heping Community, Fuhai Street, Bao'an District, Shenzhen, Guangdong, China. Photo 15 Photo 16 Page 9 of 17 FCC ID: 2AVSB-CB-T10 Guangdong Asia Hongke Test Technology Limited B1/F, Building 11, Junfeng Industrial Park, Chongqing Road, Heping Community, Fuhai Street, Bao'an District, Shenzhen, Guangdong, China. Photo 17 Photo 18 Earphone Coil Page 10 of 17 FCC ID: 2AVSB-CB-T10 Guangdong Asia Hongke Test Technology Limited B1/F, Building 11, Junfeng Industrial Park, Chongqing Road, Heping Community, Fuhai Street, Bao'an District, Shenzhen, Guangdong, China. Photo 19 Photo 20 Page 11 of 17 FCC ID: 2AVSB-CB-T10 Guangdong Asia Hongke Test Technology Limited B1/F, Building 11, Junfeng Industrial Park, Chongqing Road, Heping Community, Fuhai Street, Bao'an District, Shenzhen, Guangdong, China. Photo 21 Photo 22 Page 12 of 17 FCC ID: 2AVSB-CB-T10 Guangdong Asia Hongke Test Technology Limited B1/F, Building 11, Junfeng Industrial Park, Chongqing Road, Heping Community, Fuhai Street, Bao'an District, Shenzhen, Guangdong, China. Photo 23 Photo 24 Page 13 of 17 FCC ID: 2AVSB-CB-T10 Guangdong Asia Hongke Test Technology Limited B1/F, Building 11, Junfeng Industrial Park, Chongqing Road, Heping Community, Fuhai Street, Bao'an District, Shenzhen, Guangdong, China. Photo 25 Photo 26 Watch Coil Page 14 of 17 FCC ID: 2AVSB-CB-T10 Guangdong Asia Hongke Test Technology Limited B1/F, Building 11, Junfeng Industrial Park, Chongqing Road, Heping Community, Fuhai Street, Bao'an District, Shenzhen, Guangdong, China. Photo 27 Photo 28 Page 15 of 17 FCC ID: 2AVSB-CB-T10 Guangdong Asia Hongke Test Technology Limited B1/F, Building 11, Junfeng Industrial Park, Chongqing Road, Heping Community, Fuhai Street, Bao'an District, Shenzhen, Guangdong, China. Photo 29 Photo 30 Page 16 of 17 FCC ID: 2AVSB-CB-T10 Guangdong Asia Hongke Test Technology Limited B1/F, Building 11, Junfeng Industrial Park, Chongqing Road, Heping Community, Fuhai Street, Bao'an District, Shenzhen, Guangdong, China. Photo 31 Photo 32 Page 17 of 17 FCC ID: 2AVSB-CB-T10 Guangdong Asia Hongke Test Technology Limited B1/F, Building 11, Junfeng Industrial Park, Chongqing Road, Heping Community, Fuhai Street, Bao'an District, Shenzhen, Guangdong, China. Photo 33 Photo 34 ------End------

Operation of Description This product name is Wireless Charger stand model name is CBT-10 The EUT is working base on the IC RF chipset D9512 application. The EUT equipped with RF chipset D9015A,D9005,JW5357M. The D9015A chip is used to control parts of the phone, the D9005 chip is used to control parts of the earphone, the JW5357M chip is used to control parts of the watch. A. Use qc/PD adapter to power the product, and put the device (watch or phone or earphone) that supports QI protocol charging on the product for fast charging. B. After the qc/PD adapter is used to power the product,generate a certain current in the coil through electromagnetic induction. C. The EUT received DC 5V/9V from adapter. products description Product Wireless Charger Frequency Range Coil1: For Phone: 113kHz-205kHz Coil2: For Earphone: 113kHz-205kHz Coil3: Watch: 300kHz-350kHz Modulation Technique: ASK Antenna Type Coil1/Coil2/Coil3: Loop coil Antenna Antenna Gain Coil1/Coil2/Coil3: 0dBi HW V1.1 SW V1.0 Power supply Input: DC 5V⎓3A, 9V⎓3A Phone Output: 5W,10W,15W Earphone Output: 2.5W Watch Output: 2.5W

Note: This device has been tested and found to comply with the standard(s) listed, this test report merely corresponds to the test sample. It is not permitted to copy extracts of these test result without the written permission of the test laboratory. This report shall not be reproduced except in full, without the written approval of Guangdong Asia Hongke Test Technology Limited. If there is a need to alter or revise this document, the right belongs to Guangdong Asia Hongke Test Technology Limited, and it should give a prior written notice of the revision document. This test report must not be used by the client to claim product endorsement. Guangdong Asia Hongke Test Technology Limited B1/F, Building 11, Junfeng Industrial Park, Chongqing Road, Heping Community, Fuhai Street, Bao'an District, Shenzhen, Guangdong, China. TEST REPORT Product Name : Wireless Charger Brand Name : N/A Model : CBT-10 Series Model : N/A FCC ID : 2AVSB-CB-T10 Applicant : Shenzhen Mgctech Co.,Ltd. Address : 401, Bldg.14, No. 48-12, Fuchengao Rd., Pinghu Street, Longgang District, Shenzhen,China. Manufacturer : Shenzhen Mgctech Co.,Ltd. Address : 401, Bldg.14, No. 48-12, Fuchengao Rd., Pinghu Street, Longgang District, Shenzhen,China. Standard(s) : FCC CFR 47 PART 1, § 1.1310 KDB 680106 D01 Wireless Power Transfer v04 Date of Receipt : Aug.14, 2024 Date of Test : Aug.14, 2024~ Aug.22, 2024 Issued Date : Aug.22, 2024 Issued By: Guangdong Asia Hongke Test Technology Limited B1/F, Building 11, Junfeng Industrial Park, Chongqing Road, Heping Community, Fuhai Street, Bao'an District, Shenzhen, Guangdong, China Tel.: +86 0755-230967639 Fax.: +86 0755-230967639 Reviewed by: Approved by: Leon.yi Sean She Page 2 of 14 Report No.: AiTSZ-240814002W4 Report Revise Record Report Version Issued Date Notes M1 Aug.22, 2024 Initial Release Page 3 of 14 Report No.: AiTSZ-240814002W4 Contents 1 GENGENERAL INFORMATION ................................................................................................................................ 4 1.1 ENVIRONMENTAL CONDITIONS ........................................................................................................................................ 4 1.2 GENERAL DESCRIPTION OF EUT ...................................................................................................................................... 4 1.3 TEST FACILITY .............................................................................................................................................................. 5 1.4 MEASUREMENT UNCERTAINTY ........................................................................................................................................ 5 2.1 DESCRIPTION OF THE TEST MODE ..................................................................................................................................... 6 2.2 SPECIAL ACCESSORIES ................................................................................................................................................... 6 2.3 EQUIPMENT LIST FOR THE TEST ....................................................................................................................................... 6 3 TEST CONDITIONS AND RESULTS ........................................................................................................................... 7 3.1 APPLICABLE STANDARD .................................................................................................................................................. 7 3.2 LIMIT ......................................................................................................................................................................... 7 3.3 TEST SETUP ................................................................................................................................................................. 7 3.4 MEASUREMENT PROCEDURE .......................................................................................................................................... 8 3.5 TEST RESULT OF E AND H FIELD STRENGTH ........................................................................................................................ 8 3.6 EQUIPMENT APPROVAL CONSIDERATIONS ....................................................................................................................... 11 3.7 CONCLUSION ............................................................................................................................................................. 11 4 TEST SETUP PHOTOGRAPHS OF EUT .................................................................................................................... 12 Page 4 of 14 Report No.: AiTSZ-240814002W4 1 GENGENERAL INFORMATION 1.1 Environmental conditions During the measurement the environmental conditions were within the listed ranges: Normal Temperature: 25°C Relative Humidity: 55 % Air Pressure: 101 kPa 1.2 General Description of EUT Product Name: Wireless Charger Model/Type reference: CBT-10 Power Supply: Input: DC 5V⎓3A, 9V⎓3A Phone Output: 5W,10W,15W Earphone Output: 2.5W Watch Output: 2.5W Hardware version: V1.1 Software version: V1.0 Sample(s) Status: AiTSZ-240814002-01(Normal sample) AiTSZ-240814002-02(Engineer sample) Wireless Charger: Operation frequency: Coil1: For Phone: 113kHz-205kHz Coil2: For Earphone: 113kHz-205kHz Coil3: Watch: 300kHz-350kHz Modulation Technology: ASK Antenna Type: Loop coil Antenna Antenna gain: 0dBi Remark: The above DUT's information was declared by manufacturer. For more detailed features description, please refer to the manufacturer’s specifications or the User's Manual. Page 5 of 14 Report No.: AiTSZ-240814002W4 1.3 Test Facility Test Laboratory: Guangdong Asia Hongke Test Technology Limited B1/F, Building 11, Junfeng Industrial Park, Chongqing Road, Heping Community, Fuhai Street, Bao'an District, Shenzhen, Guangdong, China The test facility is recogni…

Text truncated - open the document above for the full version.

RevisionDateDescription DRAWING NO: SIZE: SCALE: SHEET 1 OF 1 TITLE: COMPANY: RELEASED: DRAWN: Shenzhen Blande Technology Co., Ltd. Chenyan Qin BingA4 V2.0 2023.12.18pp Version D9516+D9015A V0=7-18V T1 Controller GND G N D BOOST_VOUT A _ I S E N S 3V3 3V3 3V3 A_ISENS VBUS_VIN B O O S T _ V O U T 3V3 A_PWM1 A_PWM2 3V3 CAP2_SEL CAP3_SEL SDA SCL BOOST_VOUT SW SW VBUS_VIN D M D M DP 3V3 CAP2_SEL VCC-SW_100V CAP3_SEL VCC-SW_100V CTX3 SW2 SW2 CTX2 V_BACK 3 V 3 B O O S T _ P W M BOOST_PWM 3V3 VCC V C C SDA BOOST_VOUT 3V3 3V3 DC A _ P W M 2 A _ P W M 1 V_BACK VCC-SW_100V CTX2 CTX3 S W 2 B O O S T _ V O U T B O O S T _ V O U T SW2 3 V 3 V_BACK DP VBUS_VIN GND DM CC2 CC1 C C 2 C C 1 SCL 3V3 SCL SDA 3V3 LED2 VDD+5.2V L E D 1 9 8 0 0 L E D 1 L E D 2 B8 A8 C 4 0 C 5 0 C 5 1 C 8 5 R 5 7 C 9 3 C 9 4 C 5 4 C 1 3 9 C 3 0 C 3 7 C 2 3 C 3 4 U1 C80 C4 C 4 2 C87 R89 R 9 0 R91 C88 R2 R 5 C3 C 8 4 R 8 5 NTC R 3 9 R 4 0 C 1 3 R10 R9 Q4 C 7 L4 C8 C 9 C 1 0 C 1 2 C 1 5 C 1 6 C17 R 2 0 C 1 8 C 2 0 C 2 1 R21 R22 R 2 3 Y1 R80 C22 C95 R 5 3 R 5 4 R 5 5 R 5 6 R27 R 2 8 R29 C 3 3 R30 R 1 2 R16 R17 R18 R19 R 9 6 R 3 1 R32 R33 R35 R36 R 1 0 2 Q 1 1 Q 1 2 C 4 4 C 4 5 C 4 6 C 4 7 R 3 7 R38 C36 R 4 1 C 3 8 U2 C 5 9 C32 R 4 4 R 4 5 Q1-A Q1-B Q2-A Q2-B U5 J 1 R26 C 2 4 C 2 5 R46 R62 C 5 3 R65 C 5 5 U7 R63 C52 R66 U6 R 6 7 C56 R68 R69 C57 C61 R 5 8 C49 R50 C58 C19 R11 R25 C26 C14 R 1 0 7 C 3 9 R 1 1 4 C 3 5 C 6 0 R 7 C 5 R 1 3 C 6 C2 C27 C28 C31 C1 C41 R 4 8 C 4 3 R 4 9 C 4 8 R 6 0 C 6 4 R 6 1 C 6 5 R64 L2 L1 R 6 C11 R 3 4 C 2 9 R 4 2 D8 R43 MARK1MARK2 C 6 2 C 6 3 D 5 D 6 D 7 D 3 R 3 R 4 T2 D4 U S B _ C 1 R95 R99 R47 L 3 U3 R87 Q10 R110 R111 R101 Q 3 R 1 1 2 R 1 1 3 L E D 2 5 L E D 1 L E D 2 L E D 3 L E D 4 L E D 5 L E D 6 LED7 LED8 LED9 LED10 LED11 LED12 LED13 R 1 R 1 1 5 VDD OSC_IN OSC_OUT NRST1 VDDA A_DM0 A_ISENS VIN_VBUS SWCLK SWDIO CAP2_SEL CAP1_SEL I2C_SDA/USART_RX I2C_SCL/USART_TX I2C_CTRL VDD B O O S T _ P W M C C 1 C C 2 D - D + 2 D - 2 N C V S S V S S A _ P W M 2 A _ P W M 1 L E D X 2 _ B R E A T H L E D X 1 _ B R E A T H N C A _ N T C B O O S T _ V O U T G N D BS OUT OUT OUT OUT L X P G N D P G N D I L M T N C FB FS MODE EN SVIN N C V C C N C L X L X S 1 G 1 S 2 G 2 D 2 D 2 D 1 D 1 D1D2 S 1 G 1 S 2 G 2 D 2 D 2 D 1 D 1 D1D2 VIN1 GND VIN2 B V I N B G N D BST2 V 3 3 B 5 V B B S T B S W SW2 SW1 BST1 V 2 5 I S E N S E N C P W M 1 P W M 2 V S S SDA VCC SCL GND GND GND 1234 G N D IN+ OUT IN- V + G N D IN+ OUT IN- V + GND1 GND2 VBUS1 VBUS2 SBU2 CC1 D-1 D+1 D-2 D+2 SBU1 CC2 G N D 5 VBUS3 N C 1 N C 2 G N D 6 G N D 8 VBUS4 GND3 GND4 G N D 7 NC SCL A2 A1NC IRQ HRST SDA NA VCC NC GND B C E B C E 2 2 U F / 1 6 V 1 0 0 N F / 2 5 V 1 0 0 N F / 1 6 V 1 0 U F / 6 . 3 V 2 R 1 N F / 2 5 V 1 0 0 N F / 1 6 V 2 2 U F / 2 5 V 1 0 0 N F / 2 5 V 1 0 0 N F / 2 5 V 2 2 U F / 2 5 V 1 0 0 N F / 2 5 V 2 2 U F / 2 5 V 1 2 3 4 5 6 7 8 24 23 22 21 20 19 18 17 2 5 2 6 2 7 2 8 2 9 3 0 3 1 3 2 1 6 1 5 1 4 1 3 1 2 1 1 1 09 0 D9512 10NF/16V 100NF/16V 1 0 0 N F / 1 6 V 10NF/16V 3K/1% 1 K / 1 % 10K/1% 10NF/25V 1K/1% 1 0 K / 1 % 10NF/25V 1 0 0 N F / 1 6 V 1 0 0 K / 1 % 100K/3% B值3950/NC 1 0 0 K 1 0 0 K 1 0 0 N F / 1 6 V 2.2K 2.2K 1 2 3 4 5 6789 1 0 11 12 13 14 15 1 6 1 7 1 8 1 9 2 0 QFN3X3-20 JW5513 1 0 0 n F / 5 0 V 一体成型功率电感:SCCB0620PA3R3M 1uF/6.3V 2 2 U F / 2 5 V 1 0 0 N F / 2 5 V 2 2 U F / 2 5 V 2 2 U F / 2 5 V 2 2 U F / 2 5 V 1uF/25V 1 0 R 2 2 U F / 2 5 V 2 2 U F / 2 5 V 2 2 U F / 2 5 V 20K 374K±1% 2 0 0 K ± 1 % 14.31818MHZ-10PPM-20PF 1M 20PF/50V/5% 20PF/50V/5% 2 0 K / 1 % 4 . 7 K / 1 % 1 . 2 K / 1 % 5 . 1 K / 1 % 220K±1% 1 6 K ± 1 % 33K±1% 4 7 N F / 2 5 V 33K±1% 3 K 10K 1K 10K 33K 3 3 K 3 K 10K 1K 10K 33K 3 3 K 1234 5678 0 01 RDS(ON)<14mΩ HXR13V06D 2N_MOS_60V/25A 1234 5678 0 01 RDS(ON)<14mΩ HXR13V06D 2N_MOS_60V/25A 1 0 0 n F / 5 0 V 1 0 0 n F / 5 0 V 1 0 0 n F / 5 0 V 1 0 0 n F / 5 0 V 5 . 1 K 51K/1% 4.7NF/50V 5 . 1 K 3 3 P F / 5 0 V 1 2 3 45 10 9876 11 12 13 1 4 1 5 1 9 1 8 1 7 1 6 Power Stage 15W(Duty) D9015A 1 u F / 6 . 3 V N/A 1 1 5 K ± 1 % / N C 3 5 . 7 k Ω / N C E1C1 B 1 M M B T 5 4 5 1 D W - S O T - 3 6 3 B2 C 2 E 2 E1C1 B 1 M M B T 5 4 5 1 D W - S O T - 3 6 3 B2 C 2 E 2 1 2 3 6 5 4 T91-406 烧录口 N/A 1 0 0 N F / 1 6 V 1 u F / 6 . 3 V 240R 10K/1% 4 . 7 N F / 5 0 V 10K/1% 4 . 7 N F / 5 0 V 2 1 4 3 5 OP-A_23-5 100K/1% 100nF/50V 2.2M/1% 2 1 4 3 5 OP-A_23-5 1 0 0 K / 1 % 100nF/50V 10K/1% 680K/1% 100NF/16V 100NF/16V 1 0 K / 1 % 4.7NF/50V NC NC 100nF/50V 2R 2R V683J1206C0G500N1P 100nF/50V 2 R 3 . 3 N F / 5 0 V 2 R 3 . 3 N F / 5 0 V N / A 2 R 8 2 0 p F / 5 0 V 2 R 8 2 0 p F / 5 0 V 33nF/50V±5%_NPO V104J1206C0G500N1P V104J1206C0G500N1P V104J1206C0G500N1P V104J1206C0G500N1P INF/50V N C N C N C N C N / A N / A N / A N / A 2R 1 0 0 K 5.6NF/50V 1 0 0 K 1 0 N F / 5 0 V 3 3 K 510R N C N C S U R G E 0 4 B 0 3 S U R G E 0 4 B 0 3 S U R G E 0 4 B 0 3 S U R G E 0 4 B 0 3 5 . 1 K 5 . 1 K SMF15A A1 B12 A4 B9 B8 A5 B7 A6 A7 B6 A8 B5 1 B4 3 4 5 6 A9 B1 A12 2 T Y P E - C - 1 6 P I N 非 沉 板 NC NC 240R 1 0 U H , 4 0 0 m A 0 6 0 3 1 2 3 49 10 11 12 5 6 8 7 ID 20618_ DFN12 2R 1 3 2 SS8050 1K 51K 10R 1 32 S S 8 0 5 0 1 K 5 1 K 冰 蓝 冰 蓝 冰 蓝 冰 蓝 冰 蓝 冰 蓝 冰 蓝 白灯 白灯 白灯 白灯 白灯 白灯 白灯 5 1 R 5 1 R RevisionDateDescription DRAWING NO: SIZE: SCALE: SHEET 1 OF 1 TITLE: COMPANY: RELEASED: DRAWN: Shenzhen Blande Technology Co., Ltd. Chenyan Qin BingA4 V2.0 2023.12.18pp Version D9200+D9015A EMI Fyi Not enforce DC-DC DC-DC Controller VDD+5.2V E3V3 LGATE_B UGATE_B LGATE_A UGATE_A V - B A C K _ A PHASE_A PHASE_B VDD+5.2VVDD+5.2V UGATE_A L G A T E _ B D+2 D-2 P H A S E _ A L G A T E _ A U G A T E _ B P H A S E _ B E 3 V 3 V-BACK_A PHASE_A P H A S E _ B PGND P G N D PGND PGND VDD+5.2V E3V3 E3V3 E3V3 E3V3 VDD+5.2V PHASE_A VDD+5.2V VBUS_VIN 9 8 0 0 VDD5.1V VBUS_VIN D+2 D-2 E3V3 D- B8 A8 A8 B8 D - D - R 8 R14 C66 R 1 5 R 5 2 R59 R71 R72 R73 U4U8 C67 C68 R74R75 C69 C70 C71 C72 C 7 3 C 7 4 C 7 5 C 7 6 R76 U9 C77 R 7 7 R78 C78 R 7 9 C 7 9 C81 C 8 2 C 8 3 R 8 2 C 8 6 C89 U10 C 9 0 C 9 1 R 8 3 R84 J 2 C 9 2 R 8 6 NTC1 C96 C97 C98 R92R93 C99 AL1 R94 C100 R100 C 1 0 4 C 1 0 5 R 9 7 R103 C 1 0 6 C 1 0 7 R 1 0 …

Text truncated - open the document above for the full version.

Note: This device has been tested and found to comply with the standard(s) listed, this test report merely corresponds to the test sample. It is not permitted to copy extracts of these test result without the written permission of the test laboratory. This report shall not be reproduced except in full, without the written approval of Guangdong Asia Hongke Test Technology Limited. If there is a need to alter or revise this document, the right belongs to Guangdong Asia Hongke Test Technology Limited, and it should give a prior written notice of the revision document. This test report must not be used by the client to claim product endorsement. Guangdong Asia Hongke Test Technology Limited B1/F, Building 11, Junfeng Industrial Park, Chongqing Road, Heping Community, Fuhai Street, Bao'an District, Shenzhen, Guangdong, China. TEST REPORT Product Name : Wireless Charger Brand Name : N/A Model : CBT-10 Series Model : N/A FCC ID : 2AVSB-CB-T10 Applicant : Shenzhen Mgctech Co.,Ltd. Address : 401, Bldg.14, No. 48-12, Fuchengao Rd., Pinghu Street, Longgang District, Shenzhen,China. Manufacturer : Shenzhen Mgctech Co.,Ltd. Address : 401, Bldg.14, No. 48-12, Fuchengao Rd., Pinghu Street, Longgang District, Shenzhen,China. Standard(s) : FCC CFR Title 47 Part 15 Subpart C Date of Receipt : Aug.14, 2024 Date of Test : Aug.14, 2024~ Aug.22, 2024 Issued Date : Aug.22, 2024 Issued By: Guangdong Asia Hongke Test Technology Limited B1/F, Building 11, Junfeng Industrial Park, Chongqing Road, Heping Community, Fuhai Street, Bao'an District, Shenzhen, Guangdong, China Tel.: +86 0755-230967639 Fax.: +86 0755-230967639 Reviewed by: Approved by: Leon.yi Sean She Page 2 of 21 Report No.: AiTSZ-240814002W3 Report Revise Record Report Version Issued Date Notes M1 Aug.22, 2024 Initial Release Page 3 of 21 Report No.: AiTSZ-240814002W3 Contents 1 TEST SUMMARY .................................................................................................................................................... 4 1.1 TEST STANDARDS.......................................................................................................................................................... 4 1.2 TEST SUMMARY ........................................................................................................................................................... 4 1.3 TEST FACILITY .............................................................................................................................................................. 5 1.4 MEASUREMENT UNCERTAINTY ........................................................................................................................................ 5 2 GENGENERAL INFORMATION ................................................................................................................................ 6 2.1 ENVIRONMENTAL CONDITIONS ........................................................................................................................................ 6 2.2 GENERAL DESCRIPTION OF EUT ...................................................................................................................................... 6 2.3 DESCRIPTION OF THE TEST MODE ..................................................................................................................................... 7 2.4 SPECIAL ACCESSORIES ................................................................................................................................................... 7 2.5 EQUIPMENT LIST FOR THE TEST ....................................................................................................................................... 7 3 TEST CONDITIONS AND RESULTS ........................................................................................................................... 9 3.1 CONDUCTED EMISSIONS TEST ......................................................................................................................................... 9 3.2 RADIATED EMISSIONS .................................................................................................................................................. 12 3.3 20DB BANDWIDTH ..................................................................................................................................................... 18 3.4 ANTENNA REQUIREMENT ............................................................................................................................................. 20 4 TEST SETUP PHOTOGRAPHS OF EUT .................................................................................................................... 21 5 EXTERNAL PHOTOGRAPHS OF EUT ...................................................................................................................... 21 6 INTERNAL PHOTOGRAPHS OF EUT ...................................................................................................................... 21 Page 4 of 21 Report No.: AiTSZ-240814002W3 1 TEST SUMMARY 1.1 Test Standards The tests were performed according to following standards: FCC Rules Part 15.207,15.209, 15.215(c) ANSI C63.10: 2013: American National Standard for Testing Unlicensed Wireless Devices 1.2 Test Summary Test Item Section in CFR 47 Test Result Electric Field Radiated Emissions FCC Part 15 C (Section15.209) PASS 20dB Bandwidth/99% Bandwidth FCC Part 15 C (Section15.215(c)) PASS AC Power Line Conducted Emission FCC Part 15 C (Section15.207) PASS Antenna Requirement FCC Part 15 C (Section15.203 PASS Page 5 of 21 Report No.: AiTSZ-240814002W3 1.3 Test Facility Test Laboratory: Guangdong Asia Hongke Test Technology Limited B1/F, Building 11, Junfeng Industrial Park, Chongqing Road, Heping Community, Fuhai Street, Bao'an District, Shenzhen, Guangdong, China The test facility is recognized, certified or accredited by the following organizations: FCC-Registration No.: 251906 Designation Number: CN1376 Guangdong A…

Text truncated - open the document above for the full version.

Customer name: DESCRIPTION : DATE:2024-6-13 REV.NO.:A0 Departm ent Quality Project Department Developmen t Project Procurement Quality Admission ADD：Guanlan Guanhuan Guanzhong Road, Longhua new district, Shenzhen City TEL：15112254520 page:1/2 Notes: Shenzhen Hongri Shengwei Technology Co. , Ltd. HRSW ELECTRONICS CO.,LTD Notes: Remarks: Shenzhen Lijing Technology Co. , Ltd. recognizes the signature, seal Confirmation/d ate Audit/date Approval/dateCompany seal Tung Wan HungLui WaiSimon Wai Ho Wai-wahWAI lap-hungHo Wai-wah SPECIFICATION FOR APPROVAL Shenzhen Lijing Technology Co. , Ltd. CUSTOMER P/N: SPECIFICATION：36 * 33 soft magnetic 6.5 uh 140MM Hongri Shengwei technology admitted to sign, seal Confirmation/d ate Audit/dateApproval/date seal of company 1.MECHANICAL DIMENSION (UNIT:mm) 2.SCHEMATICS: AB DEThickness 140±536±1 8±2 30±22.3Max 3.WINDING： 1.1底部印字100 STE P TAPE REMAR K N1 4.ELECTRICAL SPECIFICATION: ITEM SPEC 5.BILF OF MATERIAL： NO.SGS NO. 1 2 3 4 5 page:2/2 Antenna gain: 113kHz-205kHz Loop coil Antenna 0dBi 天线增益Antenna gain: Ho Wai-wahWEI LIWEI LI TES T CON HRSW ELECTRONICS CO.,LTD PART NO TITLE 36 * 33 soft magnetic 6.5 uh 140MM DRAWN BYCHECKED BY APPROVED BY GlueYellow GUM 9999 LIANCHENG CO.,LTD Lead-free tin strip Lead-free tin strip QIAODO Ferrite disk36*33 ITEMMATERIAL SPECIFICATIONMANUFACTURE…

Text truncated - open the document above for the full version.