2AVTJ-CP32SPX Sandpiper Digital Display

User Manual Product Name : SPX Sandpiper Digital Display Brand Name: Connectpoint CP32 Cautions The device is installed at fixed location via trained professionals and needs to remain at least 20 centimeters away from human contact. Open door for SIM card installation Install SIM Card-1 Install SIM Card-2 Re-connect All Antenna Close door 1. Check the gasket seal to ensure it is clean and t hat there is no debris. Check the mating cover as w ell. 2. Set the cover in place. It should rest easily on the seal, with all the wiring inside the housing. 3. Tighten all 14 screws evenly, so that the seal i s not damaged. Start with the center four screws, f inish with the outer screws, and make two passes: first, gently snug; second, finish. Recommended torque: Connector DC Power Power on CP32 & Check Screen Operation • Once the installation is complete at site and once the device is powered on, all operation will be control and executed by private cloud from remote. No other setting is needed. FCC Warning • 15.19 •  This device complies with Part 15 of the FCC Rules. Operation is subject to the following two conditio ns: (1) this • device may not cause harmful interference, and (2) this device must accept any interference received, including interference that may cause undesired operation. • 15.105 • This equipment has been tested and found to comply with the limits for a Class B digital device, pursu ant to part 15 of the FCC Rules. These limits are designed to provide reasonable protection against h armful interference in a residential installation. This equipment generates, uses and can radiate radio frequency energy and, if not installed and us ed in accordance with the instructions, may cause h armful interference to radio communications. However, there is no guarantee that interference wi ll not occur in a particular installation. If this equipment does cause harmful interference to radio or television reception, which can be determined by turning the equipment off and on, the user is enco uraged to try to correct the interference by one or more of the following measures: • —Reorient or relocate the receiving antenna. • —Increase the separation between the equipment and receiver. • —Connect the equipment into an outlet on a circuit different from that to which the receiver is connec ted. • —Consult the dealer or an experienced radio/TV tech nician for help. • 15.21 •  Any changes or modifications not expressly approved by the party responsible for compliance could void the authority to operate equipment. •  This device and its antenna must not be co-located or operating in conjunction with any other antenna or transmitter. •  For product available in the USA/Canada market, onl y channel 1~11 can be operated. Selection of other channels is not possible • FCC RF Radiation Exposure Statement: • This equipment complies with FCC radiation exposure limits set forth for an uncontrolled environment. This equipment should be installed and operated with minimum distance 20cm between the rad iator & your body.

RF_160, Issue 04 Declaration of Authorization We Name: Connectpoint Inc. Address: 175 Cremona, Suite 160 City: Goleta CA 93117 Country: United States Declare that: Name Representative of agent: Kevin Tsai (1) Agent Company name: Compliance Certification Services Inc. Address: No. 11. Wugong 6th Road City: New Taipei City Country Taiwan is authorized to apply for Certification of the following product(s): Product description: SPX Sandpiper Digital Display Type designation: CP32 Trademark: Connectpoint Validity/ expiry date: February 9, 2022 on our behalf. Date: ......... February 9, 2021 City: ......... Goleta CA 93117....................... Name: ......... Chuck Menzel ....................... (2) Function: ......... CTO...................... Signature: ............................... Notes: (1): Required for FCC application (2): For FCC it must be the Grantee Code “owner” or the authorized agent.

FCC, Request for non-disclosure Date: 21-Nov-2018 RF_501, Issue 8 Page 1 of 1 Company Name: Connectpoint Inc. Address : 175 Cremona, Suite 160 City: Goleta California 93117 Country: United States To: Telefication B.V., Dept. FCC TCB Edisonstraat 12A 6902 PK ZEVENAAR The Netherlands Subject: Request for confidentiality FCC ID: 2AVTJ-CP32 Reference number: ###### Dear FCC TCB, 1. Long-Term Confidentiality Pursuant to 47 CFR Section 0.459(a) & (b), we hereby requests non-disclosure and confidential treatment of the following materials submitted in support of FCC certification application: Bill(s) of Material Block Diagrams Operational Description Schematic Diagrams Tune-up Procedure Above materials contain secrets, proprietary and technical information, which would customarily be guarded from competitors under 47 CFR, section 0.457(d)(2). Disclosure or publication or any portion of this company confidential material to other parties could cause substantial competitive harm and provide unjustified benefits for competitors. 2. Short-Term Confidentiality (STC) Pursuant to Public Notice DA 04-1705 of the Commission’s policy, in order to comply with the marketing regulations in 47 CFR §2.803 and the importation rules in 47 CFR §2.1204, a pplicant hereby requests Short-Term Confidential treatment of the following materials (See notes below): Internal Photos User’s Manual Test Set-up Photos External Photos Justification: Ensuring that business sensitive information remains confidential until the actual marketing of newly authorized devices. Date: 01/26/2021 Name and signature of applicant: Chuck Menzel Notes: 1) A document or type of document can only have ONE type of confidentiality! 2) Short-Term confidentiality is in principle for 45 days from date of grant; it can be extended max 3 times (total time 180 days max.)! The planned date should stated in the RF731 application form. 3) FCC must be informed when marketing begins earlier. 4) Release takes place automatically thus extension must be requested in time. Telefication does not remind you of this! 5) Request for extension or for release must be received by Telefication at least 7 days before date of actual marketing or before expiration of the STC period

This document cannot be reproduced except in full, without prior written approval of the Company. 本報告未經本公司書面許可，不可部份複製。 Page: 1 / 16 Report No.: T201221W04 Rev.: 00 APPENDIX 1 - PHOTOGRAPHS OF EUT EXTERNAL PHOTOGRAPHS OF EUT This document cannot be reproduced except in full, without prior written approval of the Company. 本報告未經本公司書面許可，不可部份複製。 Page: 2 / 16 Report No.: T201221W04 Rev.: 00 This document cannot be reproduced except in full, without prior written approval of the Company. 本報告未經本公司書面許可，不可部份複製。 Page: 3 / 16 Report No.: T201221W04 Rev.: 00

Sandpiper CP32 Image/Laser/Label/Printing caption Page:1 2021.01.28 Ve r.D Model CP32 Version D Date: 2021.01.28  Item A: Machine (Back Cover)-Laser B: Machine (Door) -Laser/Label C: Carton-Label/Printing Caption of Laser/Labe/Printing : 1. Content 2. Position 3. Dimension Sandpiper CP32 Image/Laser/Label/Printing caption Page:2 2021.01.28 Ve r.D ◎ A-Machine (Back Cover) *Laser 1. Content Include Logo, Power info, S/N , FCC ID（LTE + WiFi）and Identification mark 2. Position (on the center of the back cover) Sandpiper CP32 Image/Laser/Label/Printing caption Page:3 2021.01.28 Ve r.D 3. Dimension Dimension about: 64.6mm(2.54”) x33mm(1.3”) ◎ B-Machine (Door) *Laser 1. Content Sandpiper CP32 Image/Laser/Label/Printing caption Page:4 2021.01.28 Ve r.D 2. Position Unit: mm 3. Dimension Dimension about: 58.3mm(2.3”) x83.5mm(3.29”) Sandpiper CP32 Image/Laser/Label/Printing caption Page:5 2021.01.28 Ve r.D *Label 1. Content Include COO, S/N, Barcode and 15.19 warning of FCC # Barcode Type: CODE128 # S/N: M32Q46TCA250100 XXXXXX123456789 XXXXXX  Project code 12  Customer code 3  Production Year 4  Production Month 5  Production Week 6~9  Serial Number 2. Position Sandpiper CP32 Image/Laser/Label/Printing caption Page:6 2021.01.28 Ve r.D 3. Dimension Label Dimension: 60mm(2.36”)x30mm(1.18”) ◎ C-Carton *Label 1. Content Include COO, S/N and Barcode # Barcode Type: CODE128 2. Position (on the center of the frame) 3. Dimension Label Dimension: 40mm(1.57”)x20mm(0.79”) Sandpiper CP32 Image/Laser/Label/Printing caption Page:7 2021.01.28 Ve r.D *Printing 1. Content Include Logo, identification mark and carton recognize symbol 2. Position 3. Dimension Carton Dimension: 928mm(36.54”)x613mm(24.13”)x148mm(5.83”) Printing Dimension: 564mm(22.2”)x108mm(4.25”)

This document cannot be reproduced except in full, without prior written approval of the Company. 本報告未經本公司書面許可，不可部份複製。 Page: 4 / 16 Report No.: T201221W04 Rev.: 00 INTERNAL PHOTOGRAPHS OF EUT This document cannot be reproduced except in full, without prior written approval of the Company. 本報告未經本公司書面許可，不可部份複製。 Page: 5 / 16 Report No.: T201221W04 Rev.: 00 This document cannot be reproduced except in full, without prior written approval of the Company. 本報告未經本公司書面許可，不可部份複製。 Page: 6 / 16 Report No.: T201221W04 Rev.: 00 This document cannot be reproduced except in full, without prior written approval of the Company. 本報告未經本公司書面許可，不可部份複製。 Page: 7 / 16 Report No.: T201221W04 Rev.: 00 This document cannot be reproduced except in full, without prior written approval of the Company. 本報告未經本公司書面許可，不可部份複製。 Page: 8 / 16 Report No.: T201221W04 Rev.: 00 This document cannot be reproduced except in full, without prior written approval of the Company. 本報告未經本公司書面許可，不可部份複製。 Page: 9 / 16 Report No.: T201221W04 Rev.: 00 WWAN & WiFi module This document cannot be reproduced except in full, without prior written approval of the Company. 本報告未經本公司書面許可，不可部份複製。 Page: 10 / 16 Report No.: T201221W04 Rev.: 00 This document cannot be reproduced except in full, without prior written approval of the Company. 本報告未經本公司書面許可，不可部份複製。 Page: 11 / 16 Report No.: T201221W04 Rev.: 00 WWAN RF IC WWAN Crystal This document cannot be reproduced except in full, without prior written approval of the Company. 本報告未經本公司書面許可，不可部份複製。 Page: 12 / 16 Report No.: T201221W04 Rev.: 00 WiFi RF IC & Crystal This document cannot be reproduced except in full, without prior written approval of the Company. 本報告未經本公司書面許可，不可部份複製。 Page: 13 / 16 Report No.: T201221W04 Rev.: 00 WWAN Antenna This document cannot be reproduced except in full, without prior written approval of the Company. 本報告未經本公司書面許可，不可部份複製。 Page: 14 / 16 Report No.: T201221W04 Rev.: 00 This document cannot be reproduced except in full, without prior written approval of the Company. 本報告未經本公司書面許可，不可部份複製。 Page: 15 / 16 Report No.: T201221W04 Rev.: 00 WIFI Antenna This document cannot be reproduced except in full, without prior written approval of the Company. 本報告未經本公司書面許可，不可部份複製。 Page: 16 / 16 Report No.: T201221W04 Rev.: 00

FCC ID: 2AVTJ-CP32 Page 1 / 8 Report No.: T201221W04-MF1 Rev.: 00 No.11, Wugong 6th Rd., Wugu Dist., New Taipei City , Taiwan /新北市五股區五工六路11號 t:(886-2) 2299-9720 f:(886-2) 2299-9721 www.sgs.com.tw www.ccsrf.com Unless otherwise stated the results shown in this test report refer only to the sample(s) tested and such sample(s) are retained for 90 days only. 除非另有說明，此報告結果僅對測試之樣品負責，同時此樣品僅保留90天。本報告未經本公司書面許可，不可部份複製。 This document is issued by the Company subject to its General Conditions of Service printed overleaf, available on request or accessible at http://www.sgs.com.tw/Terms-and-Conditions and, for electronic format documents, subject to Terms and Conditions for Electronic Documents at http://www.sgs.com.tw/Terms-and-Conditions. Attention is drawn to the limitation of liability, indemnification and jurisdiction issues defined therein. Any holder of this document is advised that information contained hereon reflects the Company’s findings at the time of its intervention only and within the limits of client’s instruction, if any. The Company’s sole responsibility is to its Client and this document does not exonerate parties to a transaction from exercising all their rights and obligations under the transaction documents. This document cannot be reproduced, except in full, without prior written approval of the Company. Any unauthorized alteration, forgery or falsification of the content or appearance of this document is unlawful and offenders may be prosecuted to the fullest extent of the law. Compliance Certification Services Inc. 程智科技股份有限公司 Member of the SGS Group KDB 447498 D03 47 C.F.R. Part 1, Subpart I, Section 1.1310 47 C.F.R. Part 2, Subpart J, Section 2.1091 RF EXPOSURE REPORT For SPX Sandpiper Digital Display Model: CP32 Trade Name: Connectpoint Issued to Connectpoint Inc. 175 Cremona, Suite 160 Goleta California 93117 United States Issued by Compliance Certification Services Inc. Wugu Laboratory No.11, Wugong 6th Rd., Wugu Dist., New Taipei City, Taiwan. (R.O.C.) Issue Date: February 05, 2021 Note: This document may be altered or revised by Compliance Certification Services Inc. personnel only, and shall be noted in the revision section of the document. The client should not use it to claim product endorsement by TAF, NIST or any government agencies. The test results in the report only apply to the tested sample. Page 2 / 8 Report No.: T201221W04-MF1 Rev.: 00 Revision History Rev. Issue Date Revisions Effect Page Revised By 00 February 05, 2021 Initial Issue ALL Mita Wu Page 3 / 8 Report No.: T201221W04-MF1 Rev.: 00 TABLE OF CONTENTS 1. TEST RESULT CERTIFICATION ........................................................................ 4 2. LIMIT .................................................................................................................... 5 3. EUT SPECIFICATION .......................................................................................... 6 4. TEST RESULTS................................................................................................... 7 5. MAXIMUM PERMISSIBLE EXPOSURE .............................................................. 8 Page 4 / 8 Report No.: T201221W04-MF1 Rev.: 00 1. TEST RESULT CERTIFICATION We hereby certify that: The above equipment was tested by Compliance Certification Services Inc. The test data, data evaluation, test procedures, and equipment configurations shown in this report were made in accordance with the procedures given in ANSI C63.10: 2013 and the energy emitted by the sample EUT tested as described in this report is in compliance with the requirements of FCC Rules Part 15.207, 15.209, 15.247. The test results of this report relate only to the tested sample EUT identified in this report. APPLICABLE STANDARDS STANDARD TEST RESULT KDB 447498 D03 47 C.F.R. Part 1, Subpart I, Section 1.1310 47 C.F.R. Part 2, Subpart J, Section 2.1091 No non-compliance noted Statements of Conformity Determination of compliance is based on the results of the compliance measurement, not taking into account measurement instrumentation uncertainty. Approved by: Kevin Tsai Deputy Manager Compliance Certification Services Inc. Page 5 / 8 Report No.: T201221W04-MF1 Rev.: 00 2. LIMIT According to §15.247(i), systems operating under the provisions of this section shall be operated in a manner that ensures that the public is not exposed to radio frequency energy levels in excess of the Commission's guidelines. See § 1.1307(b)(1) of this chapter. Page 6 / 8 Report No.: T201221W04-MF1 Rev.: 00 3. EUT SPECIFICATION EUT SPX Sandpiper Digital Display Model CP32 Model Discrepancy N/A Frequency band (Operating) 802.11b/g/n HT20: 2412MHz ~ 2462 MHz 802.11n HT40: 2422MHz ~ 2452MHz 802.11a/n HT20: 5180MHz ~ 5240MHz / 5260 ~ 5320MHz 5500 ~ 5700MHz / 5745MHz ~ 5825MHz 802.11n HT40: 5190MHz ~ 5230MHz / 5270 ~ 5310MHZ 5510 ~ 5670MHz / 5755MHz ~ 5795MHz 802.11ac VHT80: 5210MHz / 5290MHz / 5530MHz / 5775MHz Others Device category Portable (<20cm separation) Mobile (>20cm separation) Others Exposure classification Occupational/Controlled exposure (S = 5mW/cm 2 ) General Population/Uncontrolled exposure (S=1mW/cm 2 ) Antenna Specification PCB Antenna 2.4GHz: Directional Gain :4.00 dBi (Numeric gain:2.51) Worst Maximum Measurement Average Power 2.4GHz IEEE 802.11b Mode: 21.57 dBm(143.549 mW) IEEE 802.11g Mode: 19.67 dBm(92.683 mW) IEEE 802.11n HT 20 Mode: 19.56 dBm(90.365 mW) IEEE 802.11n HT 40 Mode: 19.58 dBm(90.782 mW) Maximum tune up power 2.4GHz IEEE 802.11b Mode: 22.50 dBm(177.828 mW) IEEE 802.11g Mode: 20.50 dBm(112.202 mW) IEEE 802.11n HT 20 Mode: 20.50 dBm(112.202 mW) IEEE 802.11n HT 40 Mode: 20.50 dBm(112.202 mW) Evaluation applied MPE Evaluation* SAR Evaluation N/A Page 7 / 8 Report No.: T201221W04-MF1 Rev.: 00 4. TEST RESULTS No non-compliance noted. Calculation Given d GP E  = 30 & 377 2 E S= Where E = Field strength in Volts / meter P = Power in Watts G = Numeric antenna gain d = Distance in meters S = Power density in milliwatts / squar…

Text truncated - open the document above for the full version.

FCC ID: 2AVTJ-CP32 Page: 1 / 93 Report No.: T201221W04-RP1 Rev.: 00 No.11, Wugong 6th Rd., Wugu Dist., New Taipei City , Taiwan /新北市五股區五工六路11號 t:(886-2) 2299-9720 f:(886-2) 2299-9721 www.sgs.com.tw www.ccsrf.com Unless otherwise stated the results shown in this test report refer only to the sample(s) tested and such sample(s) are retained for 90 days only. 除非另有說明，此報告結果僅對測試之樣品負責，同時此樣品僅保留90天。本報告未經本公司書面許可，不可部份複製。 This document is issued by the Company subject to its General Conditions of Service printed overleaf, available on request or accessible at http://www.sgs.com.tw/Terms-and-Conditions and, for electronic format documents, subject to Terms and Conditions for Electronic Documents at http://www.sgs.com.tw/Terms-and-Conditions. Attention is drawn to the limitation of liability, indemnification and jurisdiction issues defined therein. Any holder of this document is advised that information contained hereon reflects the Company’s findings at the time of its intervention only and within the limits of client’s instruction, if any. The Company’s sole responsibility is to its Client and this document does not exonerate parties to a transaction from exercising all their rights and obligations under the transaction documents. This document cannot be reproduced, except in full, without prior written approval of the Company. Any unauthorized alteration, forgery or falsification of the content or appearance of this document is unlawful and offenders may be prosecuted to the fullest extent of the law. Compliance Certification Services Inc. 程智科技股份有限公司 Member of the SGS Group RADIO TEST REPORT FCC 47 CFR PART 15 SUBPART C Test Standard FCC Part 15.247 Product name SPX Sandpiper Digital Display Brand Name Connectpoint Model No. CP32 Test Result Pass Statements of Conformity Determination of compliance is based on the results of the compliance measurement, not taking into account measurement instrumentation uncertainty. The test Result was tested by Compliance Certification Services Inc. The test data, data evaluation, test procedures, and equipment configurations shown in this report were given in ANSI C63.10: 2013 and compliance standards. The test results of this report relate only to the tested sample (EUT) identified in this report. The test Report of full or partial shall not copy. Without written approval of Compliance Certification Services Inc. (Wugu Laboratory). Approved by: Tested by: Kevin Tsai Dally Hong Deputy Manager Engineer This document cannot be reproduced except in full, without prior written approval of the Company. 本報告未經本公司書面許可，不可部份複製。 Page: 2 / 93 Report No.: T201221W04-RP1 Rev.: 00 Revision History Rev. Issue Date Revisions Effect Page Revised By 00 February 05, 2021 Initial Issue ALL Mita Wu This document cannot be reproduced except in full, without prior written approval of the Company. 本報告未經本公司書面許可，不可部份複製。 Page: 3 / 93 Report No.: T201221W04-RP1 Rev.: 00 Table of contents 1. GENERAL INFORMATION ............................................................................................... 4 1.1 EUT INFORMATION ......................................................................................................... 4 1.2 EUT CHANNEL INFORMATION ....................................................................................... 5 1.3 ANTENNA INFORMATION ............................................................................................... 5 1.4 MEASUREMENT UNCERTAINTY .................................................................................... 6 1.5 FACILITIES AND TEST LOCATION................................................................................. 7 1.6 INSTRUMENT CALIBRATION ......................................................................................... 7 1.7 SUPPORT AND EUT ACCESSORIES EQUIPMENT ....................................................... 8 1.8 TEST METHODOLOGY AND APPLIED STANDARDS .................................................... 8 2. TEST SUMMERY .............................................................................................................. 9 3. DESCRIPTION OF TEST MODES .................................................................................. 10 3.1 THE WORST MODE OF OPERATING CONDITION ...................................................... 10 3.2 THE WORST MODE OF MEASUREMENT..................................................................... 11 3.3 EUT DUTY CYCLE ......................................................................................................... 12 4. TEST RESULT ................................................................................................................ 13 4.1 AC POWER LINE CONDUCTED EMISSION .................................................................. 13 4.2 6DB BANDWIDTH AND OCCUPIED BANDWIDTH (99%) ............................................. 16 4.3 OUTPUT POWER MEASUREMENT .............................................................................. 26 4.4 POWER SPECTRAL DENSITY ...................................................................................... 29 4.5 CONDUCTED BANDEDGE AND SPURIOUS EMISSION .............................................. 35 4.6 RADIATION BANDEDGE AND SPURIOUS EMISSION ................................................. 48 APPENDIX 1 - PHOTOGRAPHS OF EUT .............................................................................. A-1 This document cannot be reproduced except in full, without prior written approval of the Company. 本報告未經本公司書面許可，不可部份複製。 Page: 4 / 93 Report No.: T201221W04-RP1 Rev.: 00 1. GENERAL INFORMATION 1.1 EUT INFORMATION Applicant Connectpoint Inc. 175 Cremona, Suite 160 Goleta California 93117 United States Manufacturer Connectpoint Inc. 175 Cremona, Suite 160 Goleta California 93117 United States Equipment SPX Sandpiper Digital Display Model Name CP32 Model Discrepancy N/A Trade Name Connectpoint Received Date December 21, 2020 Date of Test December 30, 2020 ~ January 05, 2021 Po…

Text truncated - open the document above for the full version.

This document cannot be reproduced except in full, without prior written approval of the Company. 本報告未經本公司書面許可，不可部份複製。 Page: A-1 / A-4 Report No.: T201221W04-RP1 Rev.: 00 APPENDIX-A Test Photo Radiation (Below 1GHz) Radiation (Above 1GHz) This document cannot be reproduced except in full, without prior written approval of the Company. 本報告未經本公司書面許可，不可部份複製。 Page: A-2 / A-4 Report No.: T201221W04-RP1 Rev.: 00 Conducted Emission Set Up Photo This document cannot be reproduced except in full, without prior written approval of the Company. 本報告未經本公司書面許可，不可部份複製。 Page: A-3 / A-4 Report No.: T201221W04-RP1 Rev.: 00 Conduction This document cannot be reproduced except in full, without prior written approval of the Company. 本報告未經本公司書面許可，不可部份複製。 Page: A-4 / A-4 Report No.: T201221W04-RP1 Rev.: 00