2AVTJ-CP42SPX Sandpiper Digital Display

User Manual Product Name : SPX Sandpiper Digital Display Brand Name: Connectpoint CP42 Cautions The device is installed at fixed location via trained professionals and needs to remain at least 20 centimeters away from human contact. Open door for SIM card installation Install SIM Card-1 Install SIM Card-2 Insert Micro SIM Card carefully Re-connect All Antenna Close door 1.Check the gasket seal to ensure it is clean and that there is no debris. Check the mating cover as well. 2. Set the cover in place. It should rest easily on the seal, with all the wiring inside the housing. 3. Tighten all 14 screws evenly, so that the seal is not damaged. Start with the center four screws, finish with the outer screws, and make two passes: first, gently snug; second, finish. Recommended torque: Connector DC Power Power on CP42 & Check Screen Operation •Once the installation is complete at site and once the device is powered on, all operation will be control and executed by private cloud from remote. No other setting is needed. FCC Warning •15.19 •This device complies with Part 15 of the FCC Rules. Operation is subject to the following two conditions: (1) this •device may not cause harmful interference, and (2) this device must accept any interference received, including interference that may cause undesired operation. •15.105 •This equipment has been tested and found to comply with the limits for a Class B digital device, pursuant to part 15 of the FCC Rules. These limits are designed to provide reasonable protection against harmful interference in a residential installation. This equipment generates, uses and can radiate radio frequency energy and, if not installed and used in accordance with the instructions, may cause harmful interference to radio communications. However, there is no guarantee that interference will not occur in a particular installation. If this equipment does cause harmful interference to radio or television reception, which can be determined by turning the equipment off and on, the user is encouraged to try to correct the interference by one or more of the following measures: •—Reorient or relocate the receiving antenna. •—Increase the separation between the equipment and receiver. •—Connect the equipment into an outlet on a circuit different from that to which the receiver is connected. •—Consult the dealer or an experienced radio/TV technician for help. •15.21 •Any changes or modifications not expressly approved by the party responsible for compliance could void the authority to operate equipment. •This device and its antenna must not be co-located or operating in conjunction with any other antenna or transmitter. •For product available in the USA/Canada market, only channel 1~11 can be operated. Selection of other channels is not possible •FCC RF Radiation Exposure Statement: •This equipment complies with FCC radiation exposure limits set forth for an uncontrolled environment. This equipment should be installed and operated with minimum distance 20cm between the radiator & your body.

This document cannot be reproduced except in full, without prior written approval of the Company. 本報告未經本公司書面許可，不可部份複製。 Page: 1 / 17 Report No.: T210324W02-1 Rev.: 00 APPENDIX 1 - PHOTOGRAPHS OF EUT EXTERNAL PHOTOGRAPHS OF EUT This document cannot be reproduced except in full, without prior written approval of the Company. 本報告未經本公司書面許可，不可部份複製。 Page: 2 / 17 Report No.: T210324W02-1 Rev.: 00 This document cannot be reproduced except in full, without prior written approval of the Company. 本報告未經本公司書面許可，不可部份複製。 Page: 3 / 17 Report No.: T210324W02-1 Rev.: 00 This document cannot be reproduced except in full, without prior written approval of the Company. 本報告未經本公司書面許可，不可部份複製。 Page: 4 / 17 Report No.: T210324W02-1 Rev.: 00

Sandpiper CP42 Image/Laser/Label/Printing caption Page:1 2021.04.09 Ver.G Model CP42 Version G Date: 2021.04.09  Item A: Machine (Service Door)-Laser/Label B: Carton-Label/Printing Caption of Laser/Labe/Printing : 1. Content 2. Position 3. Dimension Sandpiper CP42 Image/Laser/Label/Printing caption Page:2 2021.04.09 Ver.G ◎ A-Machine (Service Door) *Laser 1. Content a. Include Logo, Power info, S/N , FCC ID（LTE + WiFi）, Model No., UL No. and Identification mark b. Sandpiper CP42 Image/Laser/Label/Printing caption Page:3 2021.04.09 Ver.G 2. Position Unit:mm 3. Dimension a. Dimension about: 65mm(2.56”) x39mm(1.54”) Sandpiper CP42 Image/Laser/Label/Printing caption Page:4 2021.04.09 Ver.G c. Dimension about: 58.3mm(2.3”) x83.5mm(3.29”) *Label 1. Content Include COO, S/N, Barcode and 15.19 warning of FCC # Barcode Type: CODE128 # S/N: M42Q46TCB15S001 XXXXXX123456789 XXXXXX  Project code 12  Customer code 3  Production Year 4  Production Month 5  Production Week 6~9  Serial Number Sandpiper CP42 Image/Laser/Label/Printing caption Page:5 2021.04.09 Ver.G 2. Position 3. Dimension Label Dimension: 60mm(2.36”)x30mm(1.18”) ◎ B-Carton *Label 1. Content Include COO, S/N and Barcode # Barcode Type: CODE128 Sandpiper CP42 Image/Laser/Label/Printing caption Page:6 2021.04.09 Ver.G 2. Position (on the center of the frame) 3. Dimension Label Dimension: 40mm(1.57”)x20mm(0.79”) *Printing 1. Content Include Logo, identification mark and carton recognize symbol 2. Position 3. Dimension Carton Dimension: 1102mm(43.39”)x869mm(34.21)x148mm(5.83”) Printing Dimension: 565mm(22.24”)x103mm(4.06”)

This document cannot be reproduced except in full, without prior written approval of the Company. 本報告未經本公司書面許可，不可部份複製。 Page: 5 / 17 Report No.: T210324W02-1 Rev.: 00 INTERNAL PHOTOGRAPHS OF EUT This document cannot be reproduced except in full, without prior written approval of the Company. 本報告未經本公司書面許可，不可部份複製。 Page: 6 / 17 Report No.: T210324W02-1 Rev.: 00 This document cannot be reproduced except in full, without prior written approval of the Company. 本報告未經本公司書面許可，不可部份複製。 Page: 7 / 17 Report No.: T210324W02-1 Rev.: 00 This document cannot be reproduced except in full, without prior written approval of the Company. 本報告未經本公司書面許可，不可部份複製。 Page: 8 / 17 Report No.: T210324W02-1 Rev.: 00 This document cannot be reproduced except in full, without prior written approval of the Company. 本報告未經本公司書面許可，不可部份複製。 Page: 9 / 17 Report No.: T210324W02-1 Rev.: 00 This document cannot be reproduced except in full, without prior written approval of the Company. 本報告未經本公司書面許可，不可部份複製。 Page: 10 / 17 Report No.: T210324W02-1 Rev.: 00 WWAN Module This document cannot be reproduced except in full, without prior written approval of the Company. 本報告未經本公司書面許可，不可部份複製。 Page: 11 / 17 Report No.: T210324W02-1 Rev.: 00 This document cannot be reproduced except in full, without prior written approval of the Company. 本報告未經本公司書面許可，不可部份複製。 Page: 12 / 17 Report No.: T210324W02-1 Rev.: 00 WWAN RF IC & Crystal This document cannot be reproduced except in full, without prior written approval of the Company. 本報告未經本公司書面許可，不可部份複製。 Page: 13 / 17 Report No.: T210324W02-1 Rev.: 00 WIFI Module WIFI RF IC & Crystal This document cannot be reproduced except in full, without prior written approval of the Company. 本報告未經本公司書面許可，不可部份複製。 Page: 14 / 17 Report No.: T210324W02-1 Rev.: 00 WWAN Antenna This document cannot be reproduced except in full, without prior written approval of the Company. 本報告未經本公司書面許可，不可部份複製。 Page: 15 / 17 Report No.: T210324W02-1 Rev.: 00 This document cannot be reproduced except in full, without prior written approval of the Company. 本報告未經本公司書面許可，不可部份複製。 Page: 16 / 17 Report No.: T210324W02-1 Rev.: 00 WIFI Antenna This document cannot be reproduced except in full, without prior written approval of the Company. 本報告未經本公司書面許可，不可部份複製。 Page: 17 / 17 Report No.: T210324W02-1 Rev.: 00

FCC ID: 2AVTJ-CP42 Page 1 / 8 Report No.: T210324W02-MF1 Rev.: 00 No.11, Wugong 6th Rd., Wugu Dist., New Taipei City , Taiwan /新北市五股區五工六路11號 t:(886-2) 2299-9720 f:(886-2) 2299-9721 www.sgs.com.tw www.ccsrf.com Unless otherwise stated the results shown in this test report refer only to the sample(s) tested and such sample(s) are retained for 90 days only. 除非另有說明，此報告結果僅對測試之樣品負責，同時此樣品僅保留90天。本報告未經本公司書面許可，不可部份複製。 This document is issued by the Company subject to its General Conditions of Service printed overleaf, available on request or accessible at http://www.sgs.com.tw/Terms-and-Conditions and, for electronic format documents, subject to Terms and Conditions for Electronic Documents at http://www.sgs.com.tw/Terms-and-Conditions. Attention is drawn to the limitation of liability, indemnification and jurisdiction issues defined therein. Any holder of this document is advised that information contained hereon reflects the Company’s findings at the time of its intervention only and within the limits of client’s instruction, if any. The Company’s sole responsibility is to its Client and this document does not exonerate parties to a transaction from exercising all their rights and obligations under the transaction documents. This document cannot be reproduced, except in full, without prior written approval of the Company. Any unauthorized alteration, forgery or falsification of the content or appearance of this document is unlawful and offenders may be prosecuted to the fullest extent of the law. Compliance Certification Services Inc. 程智科技股份有限公司 Member of the SGS Group KDB 447498 D03 47 C.F.R. Part 1, Subpart I, Section 1.1310 47 C.F.R. Part 2, Subpart J, Section 2.1091 RF EXPOSURE REPORT For SPX Sandpiper Digital Display Model: CP42 Trade Name: Connectpoint Issued to Connectpoint Inc. 175 Cremona, Suite 160 Goleta California 93117 United States Issued by Compliance Certification Services Inc. Wugu Laboratory No.11, Wugong 6th Rd., Wugu Dist., New Taipei City, Taiwan. (R.O.C.) Issue Date: June 18, 2021 Note: This document may be altered or revised by Compliance Certification Services Inc. personnel only, and shall be noted in the revision section of the document. The client should not use it to claim product endorsement by TAF, NIST or any government agencies. The test results in the report only apply to the tested sample. This document cannot be reproduced except in full, without prior written approval of the Company. 本報告未經本公司書面許可，不可部份複製。 Page 2 / 8 Report No.: T210324W02-MF1 Rev.: 00 Revision History Rev. Issue Date Revisions Effect Page Revised By 00 June 18, 2021 Initial Issue ALL Allison Chen This document cannot be reproduced except in full, without prior written approval of the Company. 本報告未經本公司書面許可，不可部份複製。 Page 3 / 8 Report No.: T210324W02-MF1 Rev.: 00 TABLE OF CONTENTS 1. TEST RESULT CERTIFICATION ........................................................................ 4 2. LIMIT .................................................................................................................... 5 3. EUT SPECIFICATION .......................................................................................... 6 4. TEST RESULTS................................................................................................... 7 5. MAXIMUM PERMISSIBLE EXPOSURE .............................................................. 8 This document cannot be reproduced except in full, without prior written approval of the Company. 本報告未經本公司書面許可，不可部份複製。 Page 4 / 8 Report No.: T210324W02-MF1 Rev.: 00 1. TEST RESULT CERTIFICATION We hereby certify that: The above equipment was tested by Compliance Certification Services Inc. The test data, data evaluation, test procedures, and equipment configurations shown in this report were made in accordance with the procedures given in ANSI C63.10: 2013 and the energy emitted by the sample EUT tested as described in this report is in compliance with the requirements of FCC Rules Part 15.207, 15.209, 15.247. The test results of this report relate only to the tested sample EUT identified in this report. APPLICABLE STANDARDS STANDARD TEST RESULT KDB 447498 D03 47 C.F.R. Part 1, Subpart I, Section 1.1310 47 C.F.R. Part 2, Subpart J, Section 2.1091 No non-compliance noted Statements of Conformity Determination of compliance is based on the results of the compliance measurement, not taking into account measurement instrumentation uncertainty. Approved by: Kevin Tsai Deputy Manager Compliance Certification Services Inc. This document cannot be reproduced except in full, without prior written approval of the Company. 本報告未經本公司書面許可，不可部份複製。 Page 5 / 8 Report No.: T210324W02-MF1 Rev.: 00 2. LIMIT According to §15.247(i), systems operating under the provisions of this section shall be operated in a manner that ensures that the public is not exposed to radio frequency energy levels in excess of the Commission's guidelines. See § 1.1307(b)(1) of this chapter. §1.1310: The criteria listed in the following table shall be used to evaluate the environment impact of human exposure to radio frequency (RF) radiation as specified in §1.1307(b), except in the case of portable devices which shall be evaluated according to the provisions of FCC part 2.1093 of the chapter. TABLE 1 - LIMITS FOR MAXIMUM PERMISSIBLE EXPOSURE (MPE) Frequency range (MHz) Electric field strength (V/m) Magnetic field strength (A/m) Power density (mW/cm 2 ) Averaging time (minutes) (A) Limits for Occupational/Controlled Exposure 0.3-3.0 614 1.63 * 100 6 3.0-30 1842/f 4.89/f * 900/f 2 6 30-300 61.4 0.163 1.0 6 300-1,500 f/300 6 1,500-100,000 5 6 (B) Limits for General Population/Uncontrolled Exposure 0.3-1.34 614 1.63 * 100 30 1.34-30 824/f 2.19/f * 180/f 2 30 30-300 27.5 0.073 0.2 30 300-1,500 f/1500 30 1,500-100,000 1.0 30 f = frequency in MHz * = Plane-wave equivalent power density Note 1 to Table 1: Occupational/controlled exposure limits apply in situations in which persons are exposed as a consequence of their empl…

Text truncated - open the document above for the full version.

FCC ID: 2AVTJ-CP42 Page: 1 / 93 Report No.: T210324W02-RP1 Rev.: 00 No.11, Wugong 6th Rd., Wugu Dist., New Taipei City , Taiwan /新北市五股區五工六路11號 t:(886-2) 2299-9720 f:(886-2) 2299-9721 www.sgs.com.tw www.ccsrf.com Unless otherwise stated the results shown in this test report refer only to the sample(s) tested and such sample(s) are retained for 90 days only. 除非另有說明，此報告結果僅對測試之樣品負責，同時此樣品僅保留90天。本報告未經本公司書面許可，不可部份複製。 This document is issued by the Company subject to its General Conditions of Service printed overleaf, available on request or accessible at http://www.sgs.com.tw/Terms-and-Conditions and, for electronic format documents, subject to Terms and Conditions for Electronic Documents at http://www.sgs.com.tw/Terms-and-Conditions. Attention is drawn to the limitation of liability, indemnification and jurisdiction issues defined therein. Any holder of this document is advised that information contained hereon reflects the Company’s findings at the time of its intervention only and within the limits of client’s instruction, if any. The Company’s sole responsibility is to its Client and this document does not exonerate parties to a transaction from exercising all their rights and obligations under the transaction documents. This document cannot be reproduced, except in full, without prior written approval of the Company. Any unauthorized alteration, forgery or falsification of the content or appearance of this document is unlawful and offenders may be prosecuted to the fullest extent of the law. Compliance Certification Services Inc. 程智科技股份有限公司 Member of the SGS Group RADIO TEST REPORT FCC 47 CFR PART 15 SUBPART C Test Standard FCC Part 15.247 Product name SPX Sandpiper Digital Display Brand Name Connectpoint Model No. CP42 Test Result Pass Statements of Conformity Determination of compliance is based on the results of the compliance measurement, not taking into account measurement instrumentation uncertainty. The test Result was tested by Compliance Certification Services Inc. The test data, data evaluation, test procedures, and equipment configurations shown in this report were given in ANSI C63.10: 2013 and compliance standards. The test results of this report relate only to the tested sample (EUT) identified in this report. The test Report of full or partial shall not copy. Without written approval of Compliance Certification Services Inc. (Wugu Laboratory). Approved by: Tested by: Kevin Tsai Dally Hong Deputy Manager Engineer This document cannot be reproduced except in full, without prior written approval of the Company. 本報告未經本公司書面許可，不可部份複製。 Page: 2 / 93 Report No.: T210324W02-RP1 Rev.: 00 Revision History Rev. Issue Date Revisions Effect Page Revised By 00 June 18, 2021 Initial Issue ALL Allison Chen This document cannot be reproduced except in full, without prior written approval of the Company. 本報告未經本公司書面許可，不可部份複製。 Page: 3 / 93 Report No.: T210324W02-RP1 Rev.: 00 Table of contents 1. GENERAL INFORMATION ............................................................................................... 4 1.1 EUT INFORMATION ......................................................................................................... 4 1.2 EUT CHANNEL INFORMATION ....................................................................................... 5 1.3 ANTENNA INFORMATION ............................................................................................... 5 1.4 MEASUREMENT UNCERTAINTY .................................................................................... 6 1.5 FACILITIES AND TEST LOCATION................................................................................. 7 1.6 INSTRUMENT CALIBRATION ......................................................................................... 7 1.7 SUPPORT AND EUT ACCESSORIES EQUIPMENT ....................................................... 8 1.8 TEST METHODOLOGY AND APPLIED STANDARDS .................................................... 8 2. TEST SUMMARY.............................................................................................................. 9 3. DESCRIPTION OF TEST MODES .................................................................................. 10 3.1 THE WORST MODE OF OPERATING CONDITION ...................................................... 10 3.2 THE WORST MODE OF MEASUREMENT..................................................................... 11 3.3 EUT DUTY CYCLE ......................................................................................................... 12 4. TEST RESULT ................................................................................................................ 13 4.1 AC POWER LINE CONDUCTED EMISSION .................................................................. 13 4.2 6DB BANDWIDTH AND OCCUPIED BANDWIDTH (99%) ............................................. 16 4.3 OUTPUT POWER MEASUREMENT .............................................................................. 26 4.4 POWER SPECTRAL DENSITY ...................................................................................... 29 4.5 CONDUCTED BANDEDGE AND SPURIOUS EMISSION .............................................. 35 4.6 RADIATION BANDEDGE AND SPURIOUS EMISSION ................................................. 48 APPENDIX 1 - PHOTOGRAPHS OF EUT .............................................................................. A-1 This document cannot be reproduced except in full, without prior written approval of the Company. 本報告未經本公司書面許可，不可部份複製。 Page: 4 / 93 Report No.: T210324W02-RP1 Rev.: 00 1. GENERAL INFORMATION 1.1 EUT INFORMATION Applicant Connectpoint Inc. 175 Cremona, Suite 160 Goleta California 93117 United States Manufacturer Connectpoint Inc. 175 Cremona, Suite 160 Goleta California 93117 United States Equipment SPX Sandpiper Digital Display Model Name CP42 Model Discrepancy N/A Trade Name Connectpoint Received Date March 24, 2021 Date of Test May 6 ~ 7, 2021 Power Supply Power from Ad…

Text truncated - open the document above for the full version.

This document cannot be reproduced except in full, without prior written approval of the Company. 本報告未經本公司書面許可，不可部份複製。 Page: A-1 / A-5 Report No.: T210324W02-RP1 Rev.: 00 APPENDIX-A Test Photo Radiation (Below 1GHz) This document cannot be reproduced except in full, without prior written approval of the Company. 本報告未經本公司書面許可，不可部份複製。 Page: A-2 / A-5 Report No.: T210324W02-RP1 Rev.: 00 Radiation (Above 1GHz) This document cannot be reproduced except in full, without prior written approval of the Company. 本報告未經本公司書面許可，不可部份複製。 Page: A-3 / A-5 Report No.: T210324W02-RP1 Rev.: 00 Conducted Emission Set Up Photo This document cannot be reproduced except in full, without prior written approval of the Company. 本報告未經本公司書面許可，不可部份複製。 Page: A-4 / A-5 Report No.: T210324W02-RP1 Rev.: 00 Conduction This document cannot be reproduced except in full, without prior written approval of the Company. 本報告未經本公司書面許可，不可部份複製。 Page: A-5 / A-5 Report No.: T210324W02-RP1 Rev.: 00