2AW68-B07801W7Bluetooth Remote Control

Bluetooth Remote Control Instruction 藍牙遙控器使用說明書 ProductName 產品名稱 Bluetooth Remote Control 藍牙遙控器 ModelName 型號名稱 B078-01-W7 Bluetooth Version 藍牙版本 5.0 Keys Number 按鍵數量 18 Power Supply 供電需求 AAA batteries* 2 2節AAA電池 Specification 規格 Remote Control Paring 遙控器藍牙配對 •Turn on the projector and wait for the Bluetooth pairing prompt on the screen.ᆞ •Bring the remote control within 10 cm / 0.33 ft fromthe projector. •Simultaneously press and hold and keys. •Release the keys after the indicator light starts flashing. •Wait until you see pairing successful message on screen. Indicator light 指示燈 Press and hold for pairing* 長按以配對 10 cm •打開投影儀，等待熒幕上出現的藍牙配對提示 •將遙控器拿到距離投影10釐米以內的地方 •同時按下按鈕和按鈕 •等待指示燈閃爍，同時鬆開兩個按鈕 •等待熒幕上出現配對成功的提示 * If the pairing is unsuccessful, repeat the above steps until the remote control indicator light stops flashing. * 如果配對失敗，請重複以上步驟，直到遙控器指示燈停止閃爍 谷歌語音鍵Google Assistant Press and hold the button to talk with Google Assistant 長按並講話來使用谷歌語音助手 對焦按鍵Focus adjustment Press to adjust focus manually 按下來調整投影儀聚焦 OK鍵OK Confirm a selection or Pause / Resume 按下來選中或暫停、播放 返回鍵Back Return to previous page 返回上一頁 流媒體應用熱鍵Streaming Apps Jumpto video streaming pages 跳轉至對應流媒體應用 Power電源鍵 Press to power on / switch to standby mode / wake up Press and hold for 3 seconds to power off 按下來開機、進入休眠模式、或喚醒投影儀，長按3秒關機 Setting設定 Press to access dash board 按下來打開控制面板 Navigation導航鍵 Control cursor on the screen 控制屏幕上的光標 Home主頁鍵 Access homepage 回到主頁 Projector Setting (Shortcuts) 投影儀設定（快捷按鍵） Access projector setting shortcut menu 打開投影儀設定快捷菜單 Volume Down/Volume Up 降低或放大音量 信號源Input Source 按下選擇輸入信號源Press to choose from input sources Remote Control Keys Function Overview 遙控器按鍵功能一覽 This device complies with part 15 of the FCC Rules. Operation is subject to the following two conditions: (1) This device may not cause harmful interference, and (2) this device must accept any interference received, including interference that may cause undesired operation. Any Changes or modifications not expressly approved by the party responsible for compliance could void the user's authority to operate the equipment. Note: This equipment has been tested and found to comply with the limits for a Class B digital device, pursuant to part 15 of the FCC Rules. These limits are designed to provide reasonable protection against harmful interference in a residential installation. This equipment generates uses and can radiate radio frequency energy and, if not installed and used in accordance with the instructions, may cause harmful interference to radio communications. However, there is no guarantee thatinterference will not occur in a particular installation. If this equipment does cause harmful interference to radio or television reception, which can be determined by turning the equipment off and on, the user is encouraged to try to correct the interference by one or more of the following measures: -Reorient or relocate the receiving antenna. -Increase the separation between the equipment and receiver. -Connect the equipment into an outlet on a circuit different from that to which the receiver is connected. -Consult the dealer or an experienced radio/TV technician for help. FCC Radiation Exposure Statement: ThedevicehasbeenevaluatedtomeetgeneralRFexposurerequirement.Thedevicecanbeusedinportableexposureconditionwithoutrestriction. FCC Statement This device contains licence-exempt transmitter(s)/receiver(s) that comply with Innovation, Science and Economic Development Canada’s licence-exempt RSS(s). Operation is subject to the following two conditions: (1) This device may not cause interference. (2) This device must accept any interference, including interference that may cause undesired operation of the device. The digital apparatus complies with Canadian CAN ICES-3 (B)/NMB-3(B). Cetappareilcontientdes émetteurs/récepteursexempts de licencequi sontconformesaux RSS exemptés de licenced'Innovation, Sciences et DéveloppementéconomiqueCanada. L'exploitationestsoumiseaux deuxconditions suivantes: (1) Cetappareilne doitpas provoquerd'interférences. (2) Cetappareildoitaccepter touteinterférence, y comprisles interférencessusceptiblesde provoquerun fonctionnementindésirablede l'appareil. l'appareilnumériquedu ciemconformecanadienpeut-3 (b) / nmb-3 (b). This device meets the exemption from the routine evaluation limits in section 2.5 of RSS 102 and compliance with RSS 102 RF exposure, users can obtain Canadian information on RF exposure and compliance. Cetappareilestconformeàl'exemptiondes limitesd'évaluation courante dansla section 2.5 du cnr-102 et conformitéavec rss102 de l'expositionaux rf, les utilisateurspeuvent obtenirdes donnéescanadiennessur l'expositionaux champs rfet la conformité. This equipment complies with Canada radiation exposure limits set forth for an uncontrolled environment. Cetéquipementestconformeaux limitesd'expositionaux rayonnementsdu Canada établiespour un environnementnon contrôlé. This equipment should be installed and operated with minimum distance 0cm between the radiator & your body. Cet équipement doit être installé et utilisé avec une distance minimale de 0 cm entre le radiateur et votre corps. ISED Statement CE Statement RF Frequency Range: Bluetooth: 2402~2480MHz; EIRP＜20dbm We declares that this device is in compliance with the essential repuirements and other relevant provisions of Directive 2014/53/EU. 根據低功率射頻器材技術規範: 取得審驗證明之低功率射頻器材，非經核准，公司、商號或使用者均不得擅自變更頻率、加大功率或變更原設計之特性及功能。低功率射頻器材之使用 不得影響飛航安全及干擾合法通信；經發現有干擾現象時，應立即停用，並改善至無干擾時方得繼續使用。前述合法通信，指依電信管理法規定作業之 無線電通信。低功率射頻器材須忍受合法通信或工業、科學及醫療用電波, 輻射性電機設備之干擾。 NCC警示語

FCC ID: 2AW68-B07801W7&IC:20522-B07801W7 TB-RF-074-1.0 Appendix III EUT External Photographs Photo 1 Appearance of EUT Photo 2 Appearance of EUT FCC ID: 2AW68-B07801W7&IC:20522-B07801W7 TB-RF-074-1.0 Photo 3 Appearance of EUT Photo 4 Appearance of EUT FCC ID: 2AW68-B07801W7&IC:20522-B07801W7 TB-RF-074-1.0 Photo 5 Appearance of EUT Photo 6 Appearance of EUT

FCC ID: 2AW68-B07801W7&IC:20522-B07801W7 TB-RF-074-1.0 Appendix I Label Appendix II Label Location

FCC ID: 2AW68-B07801W7&IC:20522-B07801W7 TB-RF-074-1.0 Appendix IV EUT Internal Photographs Photo 7 Internal of EUT Photo 8 Appearance of PCB BLE Antenna FCC ID: 2AW68-B07801W7&IC:20522-B07801W7 TB-RF-074-1.0 Photo 9 Appearance of PCB Photo 10 Appearance of PCB

Shenzhen Toby Technology Co., Ltd. Report No.: TBR-C-202405-0109-11 Page: 1 of 4 TB-RF-074-1.0 1/F.,Building 6, Rundongsheng Industrial Zone, Longzhu, Xixiang, Bao'an District, Shenzhen, Guangdong, China Tel: +86 75526509301 Fax: +86 75526509195 Maximum Permissible Exposure Evaluation FCC ID: 2AW68-B07801W7 IC: 20522-B07801W7 1. General Information about EUT 1.1 Client Information Applicant : Shenzhen SDMC Technology Co.,Ltd. Address : Room 1022, Floor 10, Building A, Customs Building, No. 2, Xin'an 3rd Road, Dalang Community, Xin'an Street, Bao'an District, Shenzhen.China Manufacturer : Shenzhen Xeme Communication Co., Ltd Address : Room 302, Building 2, Jiuzhou Industrial Park, No.10, No.19 Road Tongguan Road, Tianliao Community, Yutang Street, Guangming District, Shenzhen. China 1.2 General Description of EUT (Equipment Under Test) EUT Name : Bluetooth Remote Control Models No./HVIN : B078-01-W7 Model Different : N/A Brand Name : SDMC Sample ID : HC-C-202405-0109-01-01 Product Description : Operation Frequency: BLE: 2402MHz~2480MHz Antenna Gain: 2.2dBi PCBAntenna Power Rating : 3V DC (powered by 2pcs AAA batteries) Software Version : 0.0.4 Hardware Version : N/A Remark: The above antenna information is declared by manufacturer and for more detailed features description, please refer to the manufacturer's specifications, the laboratory shall not be held responsible. Report No.: TBR-C-202405-0109-11 Page: 2 of 4 TB-RF-074-1.0 1/F.,Building 6, Rundongsheng Industrial Zone, Longzhu, Xixiang, Bao'an District, Shenzhen, Guangdong, China Tel: +86 75526509301 Fax: +86 75526509195 The RF Exposure Evaluation for FCC: SAR Test Exclusion Calculations FCC: According to KDB 447498 D01 Mobile and Portable Devices RF Exposure Procedures and Equipment Authorization Policies v06. (1) Clause 4.3: General SAR test reduction and exclusion guidance Sub clause 4.31: Standalone SAR test exclusion considerations 1) The 1-g and 10-g SAR test exclusion thresholds for 100 MHz to 6GHz at test separation distance≤5 mm are determined by: [(max. power of channel, including tune-up tolerance, mW)/(min. test separation, mm)]*[√f (GHz) ] ≤3.0 for 1-g SAR [(max. power of channel, including tune-up tolerance, mW)/(min. test separation, mm)]*[√f (GHz) ] ≤7.5.0 for 10-g SAR Calculation: Test separation: 5mm BLE Mode(1Mbps) Frequency (GHz) Conducted Power (dBm) Turn-up Power Tolerance (dB) Max power of tune up tolerance (dBm) Max power of tune up tolerance (mw) Calculation Value Threshold Value 2.402 1.22 2±1 3 1.955 0.618 3.0 2.440 2.18 2±1 3 1.955 0.623 3.0 2.480 2.79 2±1 3 1.955 0.628 3.0 Report No.: TBR-C-202405-0109-11 Page: 3 of 4 TB-RF-074-1.0 The RF Exposure Evaluation for IC: SAR Test Exclusion Calculations IC: According to RSS-102 — Radio Frequency (RF) Exposure Compliance of Radio communication Apparatus (All Frequency Bands) Issue 5 (2) Clause 2.5.1: Exemption limits for Routine Evaluation – SAR Evaluation SAR evaluation is required if the separation distance between the user and/or bystander and the antenna and/or radiating element of the device is less than or equal to 20 cm, except when the device operates at or below the applicable output power level (adjusted for tune-up tolerance) for the specified separation distance defined in Table 1. Table 1: SAR evaluation — Exemption limits for routine evaluation based on frequency and separation distance Frequency (MHz) Exemption Limits (mW) At separation distance of ≤5 mm At separation distance of 10 mm At separation distance of 15 mm At separation distance of 20 mm At separation distance of 25 mm ≤300 71 mW 101 mW 132 mW 162 mW 193 mW 450 52 mW 70 mW 88 mW 106 mW 123 mW 835 17 mW 30 mW 42 mW 55 mW 67 mW 1900 7 mW 10 mW 18 mW 34 mW 60 mW 2450 4 mW 7 mW 15 mW 30 mW 52 mW 3500 2 mW 6 mW 16 mW 32 mW 55 mW 5800 1 mW 6 mW 15 mW 27 mW 41 mW Table 1: SAR evaluation — Exemption limits for routine evaluation based on frequency and separation distance Frequency (MHz) Exemption Limits (mW) At separation distance of 30 mm At separation distance of 35 mm At separation distance of 40 mm At separation distance of 45 mm At separation distance of ≥50 mm ≤300 223 mW 254 mW 284 mW 315 mW 345 mW 450 141 mW 159 mW 177 mW 195 mW 213 mW 835 80 mW 92 mW 105 mW 117 mW 130 mW 1900 99 mW 153 mW 225 mW 316 mW 431 mW 2450 83 mW 123 mW 173 mW 235 mW 309 mW 3500 86 mW 124 mW 170 mW 225 mW 290 mW 5800 56 mW 71 mW 85 mW 97 mW 106 mW Report No.: TBR-C-202405-0109-11 Page: 4 of 4 TB-RF-074-1.0 Calculation: BLE Mode Frequency (MHz) Conducted Output Power (dBm) Gain (dBi) E.I.R.P. (dBm) Tolerance ± (dB) Output power (Max. Turn-up Procedure) (mW) Limit (mW) 1Mbps 2402 1.22 2.2 3.42 4±1 3.162 4 2440 2.18 2.2 4.38 4±1 3.162 4 2480 2.79 2.2 4.99 4±1 3.162 4 Conclusion: The measurement results comply with the FCC Limit per 47 CFR 2.1093 and the RSS-102§4 Table 4 for the uncontrolled RF Exposure and SAR Exclusion Threshold per KDB 447498 v06, No SAR is required. -----END OF REPORT-----

浙江东胜物联技术有限公司 Dusun Electron Co.Ltd. Antenna specification 1. Antenna describe 天線形式Antenna form IFA 頻率範圍Frequency range 2.4 ~ 2.5Ghz 增益Gain 2.2dBi 駐波比係數VSWR <2.0 輸入阻抗Input Impedance 50±5Ω 天线型号 Model number DSR-1067 公司manufacture 浙江东胜物联技术有限公司 Dusun Electron Co.Ltd. 地址address 浙江省德清县武康镇丰庆街640号: No.640 Fengqing ST. Deqing, Zhejiang，313200, China 浙江东胜物联技术有限公司 Dusun Electron Co.Ltd. 2. Antenna Layout and Implementation 3. IFA Antenna S11 浙江东胜物联技术有限公司 Dusun Electron Co.Ltd. test result Fosc=2.4Ghz，S11=-11.0dB Fosc=2.44Ghz，S11=-1 1.2dB Fosc=2.4835Ghz，S11=-1 7.6dB 浙江东胜物联技术有限公司 Dusun Electron Co.Ltd. 4. VSWR test result VSWR<2.0 浙江东胜物联技术有限公司 Dusun Electron Co.Ltd. 5. 辐射方向图 Radiation direction chart 浙江东胜物联技术有限公司 Dusun Electron Co.Ltd.

Report No.: TBR-C-202405-0109-17 Page: 1 of 18 FCC ID: 2AW68-B07801W7& IC: 20522-B07801W7 TB-RF-074-1.0 RF Test Data for Bluetooth LE (Conducted Measurements) General Description of EUT Product Name: Bluetooth Remote Control Test Model: B078-01-W7 Sample ID: HC-C-202405-0109-01-01 Environmental Conditions Temperature: 24.6°C Relative Humidity: 46% Test Voltage: DC 3V Test Engineer: Mike Yan Note: For a more detailed features description, please refer to the report TBR-C-202405-0109-17 Report No.: TBR-C-202405-0109-17 Page: 2 of 18 FCC ID: 2AW68-B07801W7& IC: 20522-B07801W7 TB-RF-074-1.0 Contents 1. DTS Bandwidth ............................................................................................................................................... 3 1.1.Test Result ......................................................................................................................................... 3 1.2.Test Graphs ....................................................................................................................................... 4 2. Occupied Channel Bandwidth........................................................................................................................ 5 2.1.Test Result ......................................................................................................................................... 5 2.2.Test Graphs ....................................................................................................................................... 6 3. Maximum peak conducted output power ..................................................................................................... 7 3.1.Test Result ......................................................................................................................................... 7 3.2.Test Graphs ....................................................................................................................................... 8 4. Maximum power spectral density ................................................................................................................. 9 4.1.Test Result ......................................................................................................................................... 9 4.2.Test Graphs ..................................................................................................................................... 10 5. Band edge measurements ........................................................................................................................... 11 5.1.Test Result ....................................................................................................................................... 11 5.2.Test Graphs ..................................................................................................................................... 12 6. Conducted Spurious Emission ...................................................................................................................... 13 6.1.Test Result ....................................................................................................................................... 13 6.2.Test Graphs ..................................................................................................................................... 14 7. Duty Cycle .................................................................................................................................................... 17 7.1.Test Result ....................................................................................................................................... 17 7.2.Test Graphs ..................................................................................................................................... 18 Report No.: TBR-C-202405-0109-17 Page: 3 of 18 FCC ID: 2AW68-B07801W7& IC: 20522-B07801W7 TB-RF-074-1.0 1. DTS Bandwidth 1.1.Test Result Te s t Mode Antenna Channel DTS BW [MHz] FL[MHz] FH[MHz] Limit[MHz] Verdict BLE_1M Ant1 2402 0.72 2401.63 2402.35 0.5 PASS 2440 0.70 2439.63 2440.33 0.5 PASS 2480 0.72 2479.62 2480.34 0.5 PASS Report No.: TBR-C-202405-0109-17 Page: 4 of 18 FCC ID: 2AW68-B07801W7& IC: 20522-B07801W7 TB-RF-074-1.0 1.2.Test Graphs BLE_1M_Ant1_2402 BLE_1M_Ant1_2440 BLE_1M_Ant1_2480 Report No.: TBR-C-202405-0109-17 Page: 5 of 18 FCC ID: 2AW68-B07801W7& IC: 20522-B07801W7 TB-RF-074-1.0 2. Occupied Channel Bandwidth 2.1.Test Result Te s t Mode Antenna Channel OCB [MHz] FL[MHz] FH[MHz] Limit[MHz] Verdict BLE_1M Ant1 2402 1.63 2401.2967 2402.9271 --- --- 2440 1.419 2439.3526 2440.7712 --- --- 2480 1.171 2479.4046 2480.5754 --- --- Report No.: TBR-C-202405-0109-17 Page: 6 of 18 FCC ID: 2AW68-B07801W7& IC: 20522-B07801W7 TB-RF-074-1.0 2.2.Test Graphs BLE_1M_Ant1_2402 BLE_1M_Ant1_2440 BLE_1M_Ant1_2480 Report No.: TBR-C-202405-0109-17 Page: 7 of 18 FCC ID: 2AW68-B07801W7& IC: 20522-B07801W7 TB-RF-074-1.0 3. Maximum peak conducted output power 3.1.Test Result Te s t Mode Antenna Channel Result[dBm] Limit[dBm] Gain [dBm] EI RP [dBm] EI RP Limit [dBm] Verdict BLE_1M Ant1 2402 1.22 ≤30 2.2 3.42 ≤36 PASS 2440 2.18 ≤30 2.2 4.38 ≤36 PASS 2480 2.79 ≤30 2.2 4.99 ≤36 PASS Report No.: TBR-C-202405-0109-17 Page: 8 of 18 FCC ID: 2AW68-B07801W7& IC: 20522-B07801W7 TB-RF-074-1.0 3.2.Test Graphs BLE_1M_Ant1_2402 BLE_1M_Ant1_2440 BLE_1M_Ant1_2480 Report No.: TBR-C-202405-0109-17 Page: 9 of 18 FCC ID: 2AW68-B07801W7& IC: 20522-B07801W7 TB-RF-074-1.0 4. Maximum power spectral density 4.1.Test Result Te s t Mode Antenna Channel Result[dBm/3kHz] Limit[dBm/3kHz] Verdict BLE_1M Ant1 2402 -13.74 ≤8.00 PASS 2440 -13.18 ≤8.00 PASS 2480 -12.73 ≤8.00 PASS Report No.: TBR-C-202405-0109-17 Page: 10 of 18 FCC ID: 2AW68-B07801W7& IC: 20522-B07801W7 TB-RF-074-1.0 4.2.Test Graphs BLE_1M_Ant1_2402 BLE_1M_Ant1_2440 BLE_1M_Ant1_2480 Report No.: TBR-C-202405-0109-17 Page: 11 of 18 FCC ID: 2AW68-B07801W7& IC: 20522-B07801W7 TB-RF-074-1.0 5. Band edge…

Text truncated - open the document above for the full version.

Shenzhen Toby Technology Co., Ltd. Report No.: TBR-C-202405-0109-17 Page: 1 of 36 TB-RF-074-1.0 1/F.,Building 6, Rundongsheng Industrial Zone, Longzhu, Xixiang, Bao'an District, Shenzhen, Guangdong, China Tel: +86 75526509301 Fax: +86 75526509195 Radio Test Report FCC ID: 2AW68-B07801W7 IC: 20522-B07801W7 Report No. : TBR-C-202405-0109-17 Applicant : Shenzhen SDMC Technology Co., Ltd. Equipment Under Test (EUT) EUT Name : Bluetooth Remote Control Model No. : B078-01-W7 Series Model No. : ---- Brand Name : SDMC Sample ID : HC-C-202405-0109-01-01&HC-C-202405-0109-01-02 Receipt Date : 2024-05-29 Test Date : 2024-05-29 to 2024-06-04 Issue Date : 2024-06-04 Standards : FCC Part 15 Subpart C 15.247 RSS-247 Issue 3 August 2023 RSS-Gen Issue 5 April 2018+Amendment 1 (March 2019)+Amendment 2 (February 2021) Test Method : ANSI C63.10: 2013 KDB 558074 D01 15.247 Meas Guidance v05r02 Conclusions : PASS In the configuration tested, the EUT complied with the standards specified above. Test By : Mike Yan Reviewed By : Henry Huang Approved By : Ivan Su This report details the results of the testing carried out on one sample. The results contained in this test report do not relate to other samples of the same product. The manufacturer should ensure that all products in series production are in conformity with the product sample detailed in the report. Report No.: TBR-C-202405-0109-17 Page: 2 of 36 TB-RF-074-1.0 Contents CONTENTS ............................................................................................................................................ 2 1. GENERAL INFORMATION ABOUT EUT ............................................................................. 5 1.1 Client Information ................................................................................................................ 5 1.2 General Description of EUT (Equipment Under Test) ................................................... 5 1.3 Block Diagram Showing the Configuration of System Tested ...................................... 6 1.4 Description of Support Units .............................................................................................. 7 1.5 Description of Test Mode ................................................................................................... 7 1.6 Description of Test Software Setting ................................................................................ 8 1.7 Measurement Uncertainty .................................................................................................. 8 1.8 Test Facility........................................................................................................................... 9 2. TEST SUMMARY..................................................................................................................... 10 3. TEST SOFTWARE .................................................................................................................. 10 4. TEST EQUIPMENT AND TEST SITE .................................................................................. 11 5. CONDUCTED EMISSION ...................................................................................................... 12 5.1 Test Standard and Limit ................................................................................................... 12 5.2 Test Setup........................................................................................................................... 12 5.3 Test Procedure .................................................................................................................. 12 5.4 Deviation From Test Standard......................................................................................... 13 5.5 EUT Operating Mode ........................................................................................................ 13 5.6 Test Data............................................................................................................................. 13 6. RADIATED AND CONDUCTED UNWANTED EMISSIONS ............................................ 14 6.1 Test Standard and Limit ................................................................................................... 14 6.2 Test Setup........................................................................................................................... 15 6.3 Test Procedure .................................................................................................................. 16 6.4 Deviation From Test Standard......................................................................................... 17 6.5 EUT Operating Mode ........................................................................................................ 17 6.6 Test Data............................................................................................................................. 17 7. RESTRICTED BANDS AND BAND EDGE REQUIREMENT .......................................... 18 7.1 Test Standard and Limit ................................................................................................... 18 7.2 Test Setup........................................................................................................................... 18 7.3 Test Procedure .................................................................................................................. 19 7.4 Deviation From Test Standard......................................................................................... 19 7.5 EUT Operating Mode ........................................................................................................ 19 7.6 Test Data............................................................................................................................. 19 8. BANDWIDTH TEST................................................................................................................. 20 8.1 Test Standard and Limit ..................…

Text truncated - open the document above for the full version.

FCC ID: 2AW68-B07801W7&IC:20522-B07801W7 TB-RF-074-1.0 Appendix V EUT Test Photographs Photo of Setup for Radiated Emission (30MHz~1GHz) Photo of Setup for Radiated Emission (Above 1 GHz) -----END OF REPORT-----