2AW68-D222AHD222AH Tri-band Wi-Fi 6E Extender

FEDERAL COMMUNICATION COMMISSION (FCC) INTERFERENCE STATEMENT 封面 / Cover封底 / Back cover THIS DEVICE COMPLIES WITH PART 15 OF THE FCC RULES. OPERATION IS SUBJECT TO THE FOLLOWING TWO CONDITIONS: (1) THIS DEVICE MAY NOT CAUSE HARMFUL INTERFERENCE, AND (2) THIS DEVICE MUST ACCEPT ANY INTERFERENCE RECEIVED, INCLUDING INTERFERENCE THAT MAY CAUSE UNDESIRED OPERATION. This equipment has been tested and found to comply with the limits for a Class B digital device, pursuant to part 15 of the FCC Rules. These limits are designed to provide reasonable protection against harmful interference in a residential installation. This equipment generates, uses and can radiate radio frequency energy and, if not installed and used in accordance with the instructions, may cause harmful interference to radio communications. However, there is no guarantee that interference will not occur in a particular installation. If this equipment does cause harmful interference to radio or television reception, which can be determined by turning the equipment o and on, the user is encouraged to try to correct the interference by one or more of the following measures: Wireless Statement: FCC CAUTION: - FCC regulations restrict the operation of this device to indoor use only. - IEEE 802 11b or 802 11g operation of this product in the USA is f irmware limited to channel 1~11. - The operation of this device is prohibited on oil platforms, cars, trains, boats, and aircraft, except that operation of this device is permitted in large aircraft while f lying above 10,000 feet. - Operation of transmitters in the 5.925-7.125 GHz band is prohibited for control of or communications with unmanned aircraft systems. DECLARATION OF CONFORMITY: Address: https://en.sdmctech.com/about/Certif icate.html Shenzhen SDMC Technology Co.,Ltd Room 1022, Floor 10, Building A, Customs Building, No. 2, Xin'an 3rd Road, Dalang Community, Xin'an Street, Bao'an District, Shenzhen, China D222AH Tri-band Wi-Fi 6E Extender Model: D222AH Safety Warnings: The Smart Wi-Fi Extender is a device that uses passive cooling, to avoid overheating please do not block the ventilation holes. Environmental conditions to be complied with at the installation site: humidity (0% to 95%) and temperature (41ºF to 104ºF). - Reorient or relocate the receiving antenna. - Increase the separation between the equipment and receiver. - Connect the equipment into an outlet on a circuit dif ferent from that to which the receiver is connected. - Consult the dealer or an experienced radio/TV technician for help. The grantee is not responsible for any changes or modif ications not expressly approved by the party responsible for compliance. Such modif ications could void the user's authority to operate the equipment. Radiation Exposure Statement: This equipment complies with FCC radiation exposure limits set forth for an uncontrolled environment. This equipment should be installed and operated with minimum distance 20 cm between the radiator and your body. This device and it's antennas(s) must not be co-located or operating in conjunction with any other antenna or transmitter except in accordance with FCC multi-transmitter product procedures.

Quick Installation Guide Triple Band Wi-Fi Repeater Package Content ◼ NM7886E x 1 ◼ Ethernet Cable x 1 ◼ Power Adapter x 1 ◼ Quick Installation Guide x 1 Appearance 1. Power on the repeater Turn on the power, wait until the LED indicator turns on. 2. Extend your WiFi network ① Connect your WiFi device to the repeater's SSID. Ensure that the Mobile Data (if any) function of your WiFi device is disabled. ② After connecting to the repeater's SSID, The PC connects to the RJ45 port of the Repeater device and automatically obtains an IP address,you can start a web browser, and access 192.168.1.1. ③ Enter username (admin) and password (admin) to log in. ④ Click “Router Mode” at the top of the page to view and set the device mode. Click “Scan” to scan all SSIDs in your home. ⑤ Select the WiFi network (SSID) you want to extend. ⑥ Enter the password for the selected WiFi network, and click Connect. Wait until the Status page appears. 3. Relocate the repeater Put the repeater between the gateway and the WiFi dead zone. The location you choose must be within the range of your existing WiFi network. 4. Connect to the Internet Connect your WiFi devices to the repeater with wireless or Ethernet cable, then enjoy the internet. The default SSID and password of your repeater are on the label at the bottom of the device. After the repeater is connected to the gateway, it will clone the SSID and wireless password of the gateway. Buttons and ports Button/Port Description POWER Turn on/off the device. WPS Press the button of the repeater 1 seconds to establish a WPS connection with the terminal device. RESET Press the button1 seconds and release to reboot the repeater. Press the button more than 3 seconds and release to restore the factory settings. LED Indicator status description Name State Description Power On The device is powered on. Off Power is off. WiFi On Wi-Fi has been turned on. Off Wi-Fi is off. WPS On The device is successfully connected through WPS function. Blinking The device is being connected through WPS function. Off The WPS function is not enabled, or 5 minutes after the device is successfully connected through WPS function. FAQ Q1：What should I do if cannot log in to the web UI of the repeater? A1：① If a WiFi device is used, ensure that your WiFi device has connected to the repeater's WiFi Network, and the Mobile Data (if any) function is disabled. ② If a computer is used, ensure that your computer has connected to the repeater's WiFi network, and your computer has set to Obtain an IP address automatically and Obtain DNS server address automatically. ③ Reset the repeater, and try again. Q2: What should I do if the repeater cannot find the WiFi network of my gateway? A2: ① Ensure that the WiFi network of your gateway is enabled and can be detected by your WiFi device. ② Change the channel of your gateway, and try again. ③Change the encryption type of the gateway to WPA-PSK or WPA2-PSK, and try again. Q3：How to reset the repeater? A3：When the LED of the repeater is solid on, press the RESET button on the repeater using a needle, and release it after 3 seconds. After the LED turns off, the repeater is restored to the factory settings successfully.

Shenzhen SDMC Technology Co.,Ltd. Room 1022, Floor 10, Building A, Customs Building,No. 2, Xin'an 3rd Road, Dalang Community, Xin'an Street, Bao'an District, Shenzhen, China The information provided in this letter is based on the referenced rule parts of Title 47 of the CFR as well as KDB 986446 D01. An expiration date for this letter does not exist. In case the U.S. agent changes, the grantee is obligated to notify the FCC within 30 days via the granting TCB. Federal Communications Commission Authorization and Evaluation Division Equipment Authorization Branch 7435 Oakland Mills Road Columbia, MD 21046 2023-04-20 U.S. Agent Designation Shenzhen SDMC Technology Co.,Ltd. acknowledges their consent for the following contact located in the United States to act as their agent for service of process for the equipment for which authorization is sought (FCC ID: 2AW68-D222AH): Name and company of U.S. agent: THREE STONES MEDIA LLC Physical U.S. address of agent: 1200 Broadway St. APT 329, Los Angeles, CA90015 FRN of U.S. agent: 0033401761 Email address of U.S. agent: [email protected] THREE STONES MEDIA LLC acknowledges their obligation to accept service of process on behalf of Shenzhen SDMC Technology Co.,Ltd. Shenzhen SDMC Technology Co.,Ltd. with the FRN: 0029837143 accepts its obligation to maintain an agent for service of process in the United States for no less than one year after either the grantee has permanently terminated all marketing and importation of the applicable equipment within the U.S., or the conclusion of any Commission-related administrative or judicial proceeding involving the equipment, whichever is later. By signing this form, we confirm the above and that we are aware of the application requirements listed under § 2.911(d)(7). Sincerely, Signature Ryan Yan Shenzhen SDMC Technology Co.,Ltd. Signature Sijie Zhang THREE STONES MEDIA LLC 48_[model] US_Agent_2.911(d)(7)-U, V04

CONFIDENTIALITY REQUEST for Certification Service in USA Federal Communication Commission Equipment Authorization Division, Application Processing Branch 7 435 Oakland Mills Road Columbia, MD 21046 Date: <2023-2-9> Pursuant to Paragraphs §0.457 and 0.459 of the Commission's Rules (47 C.F.R.) and Section §552(b)(4) of the Freedom of Information Act, we requests confidentiality for the following products: FCC ID 2AW68-D222AH Model name D222AH For the product stated above, we request that the following information be held confidential; Exhibits Long-Term Short-Term Short-Term Confidentiality Confidentiality Confidentiality Days External Photos □ 区 180 Internal Photos 口 区l 180 Block Diaqram 因口 Schematics 因 □ Test Setup Photos 口 区 180 User's Manual □ 区］ 180 Parts List □ Tune Up 口 Operational Descriptions 因 □ Antenna Spec. □ □ The long-term confidentiality exh心tscontain our trade secrets and proprietary info「mationthat could be of benefit to our competitors. The short-term confidentiality on the basis of ensuring that business sensitive information remains confidential until the actual marketing of our new device. If you have any questions, please feel free to contact me at the address shown below. □ 区

FCC ID: 2AW68-D222AH TB-RF-074-1.0 Appendix III EUT External Photographs Photo 1 Appearance of EUT Photo 2 Appearance of EUT FCC ID: 2AW68-D222AH TB-RF-074-1.0 Photo 3 Appearance of EUT Photo 4 Appearance of EUT FCC ID: 2AW68-D222AH TB-RF-074-1.0 Photo 5 Appearance of EUT Photo 6 Appearance of EUT FCC ID: 2AW68-D222AH TB-RF-074-1.0 Photo 7 Appearance of EUT Photo 8 Appearance of Adapter FCC ID: 2AW68-D222AH TB-RF-074-1.0 Photo 9 Appearance of EUT Photo 10 Appearance of EUT FCC ID: 2AW68-D222AH TB-RF-074-1.0 Photo 11 Appearance of EUT Photo 12 Appearance of EUT FCC ID: 2AW68-D222AH TB-RF-074-1.0 Photo 13 Appearance of EUT Photo 14 Appearance of EUT FCC ID: 2AW68-D222AH TB-RF-074-1.0 Photo 15 Appearance of EUT Photo 16 Appearance of Adapter

FCC ID: 2AW68-D222AH TB-RF-074-1.0 Appendix IID Label Appendix II ID Label Location

FCC ID: 2AW68-D222AH TB-RF-074-1.0 Appendix IV EUT Internal Photographs Photo 17 Internal of EUT Photo 18 Appearance of PCB 2.4G/5G Ant.1 6G Ant.4 6G Ant.3 6G Ant.2 6G Ant.1 2.4G/5G Ant.2 FCC ID: 2AW68-D222AH TB-RF-074-1.0 Photo 19 Appearance of PCB Photo 20 Appearance of PCB FCC ID: 2AW68-D222AH TB-RF-074-1.0 Photo 21 Appearance of PCB Photo 22 Appearance of PCB

Shenzhen Toby Technology Co., Ltd. Report No.: TBR-C-202208-0271-1 Page: 1 of 6 TB-RF-074-1.0 1/F.,Building 6, Rundongsheng Industrial Zone, Longzhu, Xixiang, Bao'an District, Shenzhen, Guangdong, China Tel: +86 75526509301 Fax: +86 75526509195 Maximum Permissible Exposure Evaluation FCC ID: 2AW68-D222AH 1. Client Information Applicant : Shenzhen SDMC Technology Co., Ltd. Address : Room 1022, Floor 10, Building A, Customs Building, No. 2, Xin'an 3rd Road, Dalang Community, Xin'an Street, Bao'an District, Shenzhen, China Manufacturer : Shenzhen SDMC Technology Co., Ltd. Address : Room 1022, Floor 10, Building A, Customs Building, No. 2, Xin'an 3rd Road, Dalang Community, Xin'an Street, Bao'an District, Shenzhen, China 2. General Description of EUT EUT Name : D222AH Tri-band Wi-Fi 6E Extender Models No. : D222AH Brand Name : Altice Labs Model Different : N/A Sample ID : 202208-0271-2-2# Operation Frequency : U-NII-1: 5180MHz~5240MHz; U-NII-2A: 5250MHz~5320MHz U-NII-2C: 5500MHz~5720MHz; U-NII-3: 5745MHz~5825MHz U-NII-5: 5955MHz~6415MHz; U-NII-6: 6435MHz~6515MHz U-NII-7: 6535MHz~6875MHz; U-NII-8: 6895MHz~7095MHz 2.4G Wi-Fi: 2412MHz~2462MHz Power Rating : AC Adapter (Model: S024-1D120200VU): Input: 100-240V~, 50/60Hz, 0.6A Output: 12.0V⎓2.0A Software Version : N/A Hardware Version : N/A Remark: (1) The adapter provided by the applicant, the verified for the RF conduction test provided by TOBY test lab. (2) Antenna information from antenna specification. Report No.: TBR-C-202208-0271-1 Page: 2 of 6 TB-RF-074-1.0 Method of Measurement for FCC 1. Max. Antenna Gain: Band Antenna Type Antenna Gain(dBi) Ant. 1 Ant. 2 2.4G WiFi PCB 3.01 4.03 5G U-NII-1 3.61 4.49 5G U-NII-2A 3.61 4.49 5G U-NII-2C 3.61 4.49 5G U-NII-3 3.61 4.49 Band Antenna Type Antenna Gain(dBi) Ant. 1 Ant. 2 Ant. 3 Ant. 4 6G U-NII-5 PCB 4.54 6.16 5.73 4.62 6G U-NII-6 4.54 6.16 5.73 4.62 6G U-NII-7 4.54 6.16 5.73 4.62 6G U-NII-8 4.54 6.16 5.73 4.62 2. EUT Operation Condition: Software provided by client enabled the EUT to transmit and receive data at lowest, middle and highest channel individually. 3. Exposure Evaluation: Equation from page 18 of OET Bulletin 65, Edition 97-01 S=(PG)/4πR 2 Where S: power density P: power input to the antenna G: power gain of the antenna in the direction of interest relative to an isotropic radiator. R: distance to the center of radiation of the antenna Simultaneous transmission MPE Considerations According to KDB447498: All transmitters and antennas in the host must be either evaluated for MPE compliance, by measurement or computational modeling, or qualify for the standalone MPE test exclusion in section 7.1.Simultaneous transmission MPE test exclusion applies when the sum of the MPE ratios for all simultaneous transmitting antennas incorporated in a host device, based on the calculated/estimated, numerically modeled or measured field strengths or power density, is ≤ 1.0. This means that: ∑ of MPE ratios ≤ 1.0 Report No.: TBR-C-202208-0271-1 Page: 3 of 6 TB-RF-074-1.0 4. Test Result: Worst MPE Result Test Mode Antenna Conducted Power(max) (dBm) Turn-up Power (dB) Max tune up power (dBm) [P] ANT Gain (dBi) [G] Distance (cm) [R] Power Density (mW/ cm 2 ) [S] 2.4G b Mode Ant1 20.08 20±1 21 3.01 20 0.0501 Ant2 20.05 20±1 21 4.03 20 0.0633 2.4G g Mode Ant1 18.73 18±1 19 3.01 20 0.0316 Ant2 18.63 18±1 19 4.03 20 0.0400 2.4G n20 Mode Ant1 18.59 18±1 19 3.01 20 0.0316 Ant2 18.50 18±1 19 4.03 20 0.0400 2.4G n40 Mode Ant1 17.64 18±1 19 3.01 20 0.0316 Ant2 17.39 18±1 19 4.03 20 0.0400 2.4G VHT20 Mode Ant1 18.71 18±1 19 3.01 20 0.0316 Ant2 18.49 18±1 19 4.03 20 0.0400 2.4G VHT40 Mode Ant1 16.74 17±1 18 3.01 20 0.0251 Ant2 16.29 17±1 18 4.03 20 0.0317 2.4G ax20 Mode Ant1 17.34 17±1 18 3.01 20 0.0251 Ant2 17.72 17±1 18 4.03 20 0.0317 2.4G ax40 Mode Ant1 16.81 17±1 18 3.01 20 0.0251 Ant2 17.32 17±1 18 4.03 20 0.0317 5G a Mode Ant1 21.53 22±1 23 3.61 20 0.0911 Ant2 22.24 22±1 23 4.49 20 0.1116 5G n20 Mode Ant1 21.40 21±1 22 3.61 20 0.0724 Ant2 21.12 21±1 22 4.49 20 0.0887 5G n40 Mode Ant1 21.41 21±1 22 3.61 20 0.0724 Ant2 21.01 21±1 22 4.49 20 0.0887 5G ac20 Mode Ant1 21.23 21±1 22 3.61 20 0.0724 Ant2 21.56 21±1 22 4.49 20 0.0887 5G ac40 Mode Ant1 21.41 21±1 22 3.61 20 0.0724 Ant2 20.91 21±1 22 4.49 20 0.0887 5G ac80 Mode Ant1 21.35 21±1 22 3.61 20 0.0724 Ant2 21.34 21±1 22 4.49 20 0.0887 5G ac160 Mode Ant1 19.48 19±1 20 3.61 20 0.0457 Ant2 18.25 19±1 20 4.49 20 0.0559 5G ax20 Mode Ant1 21.16 21±1 22 3.61 20 0.0724 Ant2 21.46 21±1 22 4.49 20 0.0887 5G ax40 Mode Ant1 21.30 21±1 22 3.61 20 0.0724 Ant2 20.80 21±1 22 4.49 20 0.0887 5G ax80 Mode Ant1 20.15 21±1 22 3.61 20 0.0724 Ant2 20.17 21±1 22 4.49 20 0.0887 5G ax160 Mode Ant1 19.65 19±1 20 3.61 20 0.0457 Ant2 18.58 19±1 20 4.49 20 0.0559 Report No.: TBR-C-202208-0271-1 Page: 4 of 6 TB-RF-074-1.0 Worst MPE Result Test Mode Max. EIRP (dBm) Max. Ant. Gain (dBi) Power (dBm) Turn-up Power (dB) Max tune up power (dBm) [P] Distance (cm) [R] Power Density (mW/ cm 2 ) [S] 6G a CDD Mode 18.91 6.16 12.75 12±1 13 20 0.0164 6G ax20 CDD Mode 18.98 6.16 12.82 12±1 13 20 0.0164 6G ax40 CDD Mode 21.77 6.16 15.61 15±1 16 20 0.0327 6G ax80 CDD Mode 24.64 6.16 18.48 18±1 19 20 0.0653 6G ax160 CDD Mode 27.45 6.16 21.29 21±1 22 20 0.1302 Note: For Power CDD mode use max. antenna Gain. 5. Conclusion: As specified in Table 1B of 47 CFR 1.1310- Limits for Maximum Permissible Exposure (MPE), Limits for General Population/ Uncontrolled Exposure Frequency Range (MHz) Power density (mW/ cm 2 ) 300-1,500 F/1500 1,500-100,000 1.0 For: 2.4G&5G&6G WiFi MPE limit S: 1mW/cm 2 The worst MPE is calculated as 0.1116mW / cm 2 < limit 1mW / cm 2 . Report No.: TBR-C-202208-0271-1 Page: 5 of 6 TB-RF-074-1.0 6. Summary simultaneous transmission information Modulation Type Work Frequency Band Transmit Antenna Antenna 1 Antenna 2 Synchronization Transmit Antenna 1 Antenna 2 IEEE 802.11a U-NII-1/ U-NII-2A U-NII-2C/ U-NII-3 Yes Yes No IEEE 802.11b 2.4GHz Yes Yes No IEEE 802.11g 2.4GHz Yes Yes No IEEE 802.11n HT…

Text truncated - open the document above for the full version.

Extender WiFi6E Antenna System Specs 2022 August 2 Version control VersiondateDescription 1.02022 March11thDocumentcreation 2.02022 May 23rdIncrease of 5mm pigtail length on SB1 3.02022 Jun 6thNew dual band PCB revision v4 (reinforce ground plane+ silkscreen) + adjustments 3.12022 Jun 9thUpdating the antennas product schematic 4.0August 05th Update Radiation Patterns, Efficiency and Gain 3 Extender WiFi6E -Antenna PN Cod.Desc.PNQty 1700271403Antenna WiFi2.4/5GHz DB1 175mm WhiteW24DB50P175WE4-BWG1 1700271404Antenna WiFi2.4/5GHz DB2 65mm BlackW24DB50P065BK4-BWG1 1700271329Antenna WiFi6GHz SB1 65mm BlackW65SB00P065BK1-BWG1 1700271400Antenna WiFi6GHz SB2 115mm GreyW65SB00P115GY1-BWG1 1700271401Antenna WiFi6GHz SB3 35mm BlackW65SB00P035BK1-BWG1 1700271402Antenna WiFi 6GHz SB4 85mm WhiteW65SB00P085WE1-BWG1 4 Antenna spec: W24DB50Pxxxxx4-BWG -dual band 2.4/5GHz 5 Antenna spec: W65SB00Pxxxx1 Single band 6GHz 6 3D system coverage (DB1) [email protected] [email protected] 7 3D system coverage (DB2) [email protected] [email protected] 8 3D system coverage (SB1, SB2) [email protected] [email protected] 9 3D system coverage (SB3,SB4) [email protected] [email protected] 10 1D radiation pattern @2.440GHz 11 1D radiation pattern @5.500GHz 12 1D radiation pattern @6.500GHz 13 Antenna Total Efficiency and Gain Antenna Efficiency % @2450MHz Efficiency % @5500MHz Efficiency % @6500MHz Gain (dBi) @2450MHz Gain (dBi) @5500MHz Gain (dBi) @6500MHz DB172.485.3-3.013.61- DB270.189.6-4.034.49- SB2--89.3--5.73 SB1--89.9--4.62 SB3--86.3--6.16 SB4--81.6--4.54 Extender WiFi6E Antenna System Specs 2022 August The present document has informational purposes only and does not constitute a formal binding offer. The information conveyeddoes not constitute an undertaking to sell the identified products and services. The present document is subject to change without notice and AlticeLabs cannot be held liable for any possible error or outdated information or for losses or damages of whatever nature resultingfrom the use of the information. Rua Eng. José Ferreira Pinto Basto, 3810 -106 Aveiro Portugal T: +351 234 403 200 F: +351 234 424 723 www.alticelabs.com

Shenzhen Toby Technology Co., Ltd. Http://www.tobylab.cn Add：1/F.,Building 6, Rundongsheng Industrial Zone, Longzhu, Xixiang, Bao'an District, Shenzhen, Guangdong, China. Report No.: TBR-C-202208-0271-2 Page: 1 of 167 FCC ID: 2AW68-D222AH TB-RF-074-1.0 RF Test Data for 2.4G Wi-Fi (Conducted Measurements) General Description of EUT Product Name: D222AH Tri-band Wi-Fi 6E Extender Test Model: D222AH Sample ID: 202208-0271-2-1# Environmental Conditions Normal Temperature: 15°C-25°C Relative Humidity: 42%-53% Normal Test Voltage: AC 120V Test Engineer: Haiting Zhou Note: For a more detailed features description, please refer to the report TBR-C-202208-0271-2. Shenzhen Toby Technology Co., Ltd. Http://www.tobylab.cn Add：1/F.,Building 6, Rundongsheng Industrial Zone, Longzhu, Xixiang, Bao'an District, Shenzhen, Guangdong, China. Report No.: TBR-C-202208-0271-2 Page: 2 of 167 FCC ID: 2AW68-D222AH TB-RF-074-1.0 Contents 1. DTS Bandwidth ............................................................................................................................................... 3 1.1.Test Result ......................................................................................................................................... 3 1.2.Test Graphs ....................................................................................................................................... 5 2. Maximum conducted output power ............................................................................................................ 21 2.1.Test Result ....................................................................................................................................... 21 3. Maximum power spectral density ............................................................................................................... 26 3.1.Test Result ....................................................................................................................................... 26 3.2.Test Graphs ..................................................................................................................................... 31 4. Band edge measurements ........................................................................................................................... 75 4.1.Test Result ....................................................................................................................................... 75 5.2.Test Graphs ..................................................................................................................................... 76 5. Conducted Spurious Emission ...................................................................................................................... 87 5.1.Test Result ....................................................................................................................................... 87 5.2.Test Graphs ..................................................................................................................................... 90 6. Duty Cycle .................................................................................................................................................. 138 6.1.Test Result ..................................................................................................................................... 138 6.2.Test Graphs ................................................................................................................................... 140 Shenzhen Toby Technology Co., Ltd. Http://www.tobylab.cn Add：1/F.,Building 6, Rundongsheng Industrial Zone, Longzhu, Xixiang, Bao'an District, Shenzhen, Guangdong, China. Report No.: TBR-C-202208-0271-2 Page: 3 of 167 FCC ID: 2AW68-D222AH TB-RF-074-1.0 1. DTS Bandwidth 1.1.Test Result TestMode Antenna Channel DTS BW [MHz] FL[MHz] FH[MHz] Limit[MHz] Verdict 11B-SISO Ant1 2412 7.08 2408.44 2415.52 0.5 PASS Ant2 2412 7.04 2408.48 2415.52 0.5 PASS Ant1 2437 7.52 2433.00 2440.52 0.5 PASS Ant2 2437 7.04 2433.48 2440.52 0.5 PASS Ant1 2462 7.08 2458.44 2465.52 0.5 PASS Ant2 2462 7.04 2458.48 2465.52 0.5 PASS 11G-SISO Ant1 2412 16.04 2404.08 2420.12 0.5 PASS Ant2 2412 16.32 2403.84 2420.16 0.5 PASS Ant1 2437 16.04 2429.08 2445.12 0.5 PASS Ant2 2437 16.12 2429.04 2445.16 0.5 PASS Ant1 2462 15.72 2454.40 2470.12 0.5 PASS Ant2 2462 16.08 2454.08 2470.16 0.5 PASS 11N20SDM Ant1 2412 17.56 2403.20 2420.76 0.5 PASS Ant2 2412 17.32 2403.20 2420.52 0.5 PASS Ant1 2437 17.56 2428.20 2445.76 0.5 PASS Ant2 2437 17.56 2428.20 2445.76 0.5 PASS Ant1 2462 17.56 2453.20 2470.76 0.5 PASS Ant2 2462 17.56 2453.20 2470.76 0.5 PASS 11N40SDM Ant1 2422 35.52 2404.24 2439.76 0.5 PASS Ant2 2422 36.32 2403.84 2440.16 0.5 PASS Ant1 2437 36.08 2419.08 2455.16 0.5 PASS Ant2 2437 36.32 2418.84 2455.16 0.5 PASS Ant1 2452 35.60 2434.16 2469.76 0.5 PASS Ant2 2452 36.32 2433.84 2470.16 0.5 PASS 11AX20SDM Ant1 2412 18.96 2402.48 2421.44 0.5 PASS Ant2 2412 18.76 2402.56 2421.32 0.5 PASS Ant1 2437 19.00 2427.48 2446.48 0.5 PASS Ant2 2437 18.56 2427.80 2446.36 0.5 PASS Ant1 2462 18.60 2452.48 2471.08 0.5 PASS Ant2 2462 18.92 2452.52 2471.44 0.5 PASS 11AX40SDM Ant1 2422 37.44 2403.12 2440.56 0.5 PASS Ant2 2422 36.64 2403.12 2439.76 0.5 PASS Ant1 2437 37.52 2418.12 2455.64 0.5 PASS Ant2 2437 37.36 2418.20 2455.56 0.5 PASS Ant1 2452 37.44 2433.12 2470.56 0.5 PASS Ant2 2452 37.52 2433.12 2470.64 0.5 PASS Shenzhen Toby Technology Co., Ltd. Http://www.tobylab.cn Add：1/F.,Building 6, Rundongsheng Industrial Zone, Longzhu, Xixiang, Bao'an District, Shenzhen, Guangdong, China. Report No.: TBR-C-202208-0271-2 Page: 4 of 167 FCC ID: 2AW68-D222AH TB-RF-074-1.0 TestMode Antenna Channel DTS BW [MHz] FL[MHz] FH[MHz] Limit[MHz] Verdict VHT20_SDM Ant1 2412 17.16 2403.60 2420.76 0.5 PASS Ant2 2412 17.56 2403.20 2420.76 0.5 PASS Ant1 2437 16.92 2428.84 2445.76 0.5 PASS Ant2 2437 17.52 2428.24 2445.76 0.5 PASS Ant1 2462 17.56 2453.20 2470.76 0.5 PASS Ant2 2462 16.96 2453.80 2…

Text truncated - open the document above for the full version.

Shenzhen Toby Technology Co., Ltd. Http://www.tobylab.cn Add：1/F.,Building 6, Rundongsheng Industrial Zone, Longzhu, Xixiang, Bao'an District, Shenzhen, Guangdong, China. Report No.: TBR-C-202208-0271-2 Page: 47 of 167 FCC ID: 2AW68-D222AH TB-RF-074-1.0 11B-CDD_Ant1_2412 11B-CDD_Ant2_2412 11B-CDD_Ant1_2437 11B-CDD_Ant2_2437 Shenzhen Toby Technology Co., Ltd. Http://www.tobylab.cn Add：1/F.,Building 6, Rundongsheng Industrial Zone, Longzhu, Xixiang, Bao'an District, Shenzhen, Guangdong, China. Report No.: TBR-C-202208-0271-2 Page: 48 of 167 FCC ID: 2AW68-D222AH TB-RF-074-1.0 11B-CDD_Ant1_2462 11B-CDD_Ant2_2462 11G-CDD_Ant1_2412 Shenzhen Toby Technology Co., Ltd. Http://www.tobylab.cn Add：1/F.,Building 6, Rundongsheng Industrial Zone, Longzhu, Xixiang, Bao'an District, Shenzhen, Guangdong, China. Report No.: TBR-C-202208-0271-2 Page: 49 of 167 FCC ID: 2AW68-D222AH TB-RF-074-1.0 11G-CDD_Ant2_2412 11G-CDD_Ant1_2437 11G-CDD_Ant2_2437 Shenzhen Toby Technology Co., Ltd. Http://www.tobylab.cn Add：1/F.,Building 6, Rundongsheng Industrial Zone, Longzhu, Xixiang, Bao'an District, Shenzhen, Guangdong, China. Report No.: TBR-C-202208-0271-2 Page: 50 of 167 FCC ID: 2AW68-D222AH TB-RF-074-1.0 11G-CDD_Ant1_2462 11G-CDD_Ant2_2462 11N20-CDD_Ant1_2412 Shenzhen Toby Technology Co., Ltd. Http://www.tobylab.cn Add：1/F.,Building 6, Rundongsheng Industrial Zone, Longzhu, Xixiang, Bao'an District, Shenzhen, Guangdong, China. Report No.: TBR-C-202208-0271-2 Page: 51 of 167 FCC ID: 2AW68-D222AH TB-RF-074-1.0 11N20-CDD_Ant2_2412 11N20-CDD_Ant1_2437 11N20-CDD_Ant2_2437 Shenzhen Toby Technology Co., Ltd. Http://www.tobylab.cn Add：1/F.,Building 6, Rundongsheng Industrial Zone, Longzhu, Xixiang, Bao'an District, Shenzhen, Guangdong, China. Report No.: TBR-C-202208-0271-2 Page: 52 of 167 FCC ID: 2AW68-D222AH TB-RF-074-1.0 11N20-CDD_Ant1_2462 11N20-CDD_Ant2_2462 11N40-CDD_Ant1_2422 Shenzhen Toby Technology Co., Ltd. Http://www.tobylab.cn Add：1/F.,Building 6, Rundongsheng Industrial Zone, Longzhu, Xixiang, Bao'an District, Shenzhen, Guangdong, China. Report No.: TBR-C-202208-0271-2 Page: 53 of 167 FCC ID: 2AW68-D222AH TB-RF-074-1.0 11N40-CDD_Ant2_2422 11N40-CDD_Ant1_2437 11N40-CDD_Ant2_2437 Shenzhen Toby Technology Co., Ltd. Http://www.tobylab.cn Add：1/F.,Building 6, Rundongsheng Industrial Zone, Longzhu, Xixiang, Bao'an District, Shenzhen, Guangdong, China. Report No.: TBR-C-202208-0271-2 Page: 54 of 167 FCC ID: 2AW68-D222AH TB-RF-074-1.0 11N40-CDD_Ant1_2452 11N40-CDD_Ant2_2452 VHT20-CDD_Ant1_2412 Shenzhen Toby Technology Co., Ltd. Http://www.tobylab.cn Add：1/F.,Building 6, Rundongsheng Industrial Zone, Longzhu, Xixiang, Bao'an District, Shenzhen, Guangdong, China. Report No.: TBR-C-202208-0271-2 Page: 55 of 167 FCC ID: 2AW68-D222AH TB-RF-074-1.0 VHT20-CDD_Ant2_2412 VHT20-CDD_Ant1_2437 VHT20-CDD_Ant2_2437 Shenzhen Toby Technology Co., Ltd. Http://www.tobylab.cn Add：1/F.,Building 6, Rundongsheng Industrial Zone, Longzhu, Xixiang, Bao'an District, Shenzhen, Guangdong, China. Report No.: TBR-C-202208-0271-2 Page: 56 of 167 FCC ID: 2AW68-D222AH TB-RF-074-1.0 VHT20-CDD_Ant1_2462 VHT20-CDD_Ant2_2462 VHT40-CDD_Ant1_2422 Shenzhen Toby Technology Co., Ltd. Http://www.tobylab.cn Add：1/F.,Building 6, Rundongsheng Industrial Zone, Longzhu, Xixiang, Bao'an District, Shenzhen, Guangdong, China. Report No.: TBR-C-202208-0271-2 Page: 57 of 167 FCC ID: 2AW68-D222AH TB-RF-074-1.0 VHT40-CDD_Ant2_2422 VHT40-CDD_Ant1_2437 VHT40-CDD_Ant2_2437 Shenzhen Toby Technology Co., Ltd. Http://www.tobylab.cn Add：1/F.,Building 6, Rundongsheng Industrial Zone, Longzhu, Xixiang, Bao'an District, Shenzhen, Guangdong, China. Report No.: TBR-C-202208-0271-2 Page: 58 of 167 FCC ID: 2AW68-D222AH TB-RF-074-1.0 VHT40-CDD_Ant1_2452 VHT40-CDD_Ant2_2452 11AX20-CDD_Ant1_2412 Shenzhen Toby Technology Co., Ltd. Http://www.tobylab.cn Add：1/F.,Building 6, Rundongsheng Industrial Zone, Longzhu, Xixiang, Bao'an District, Shenzhen, Guangdong, China. Report No.: TBR-C-202208-0271-2 Page: 59 of 167 FCC ID: 2AW68-D222AH TB-RF-074-1.0 11AX20-CDD_Ant2_2412 11AX20-CDD_Ant1_2437 11AX20-CDD_Ant2_2437 Shenzhen Toby Technology Co., Ltd. Http://www.tobylab.cn Add：1/F.,Building 6, Rundongsheng Industrial Zone, Longzhu, Xixiang, Bao'an District, Shenzhen, Guangdong, China. Report No.: TBR-C-202208-0271-2 Page: 60 of 167 FCC ID: 2AW68-D222AH TB-RF-074-1.0 11AX20-CDD_Ant1_2462 11AX20-CDD_Ant2_2462 11AX40-CDD_Ant1_2422 Shenzhen Toby Technology Co., Ltd. Http://www.tobylab.cn Add：1/F.,Building 6, Rundongsheng Industrial Zone, Longzhu, Xixiang, Bao'an District, Shenzhen, Guangdong, China. Report No.: TBR-C-202208-0271-2 Page: 61 of 167 FCC ID: 2AW68-D222AH TB-RF-074-1.0 11AX40-CDD_Ant2_2422 11AX40-CDD_Ant1_2437 11AX40-CDD_Ant2_2437 Shenzhen Toby Technology Co., Ltd. Http://www.tobylab.cn Add：1/F.,Building 6, Rundongsheng Industrial Zone, Longzhu, Xixiang, Bao'an District, Shenzhen, Guangdong, China. Report No.: TBR-C-202208-0271-2 Page: 62 of 167 FCC ID: 2AW68-D222AH TB-RF-074-1.0 11AX40-CDD_Ant1_2452 11AX40-CDD_Ant2_2452 Shenzhen Toby Technology Co., Ltd. Http://www.tobylab.cn Add：1/F.,Building 6, Rundongsheng Industrial Zone, Longzhu, Xixiang, Bao'an District, Sh…

Text truncated - open the document above for the full version.