2AW68-NM3098Dual Band Mesh Router, AX3000 Dual Band Mesh Router

Quick Installation Guide AX3000 Dual Band Mesh Router Package Content ◼ NM3098B x 2 ◼ Ethernet Cable x 1 ◼ Power Adapter x 2 ◼ Quick Installation Guide x 1 Appearance 1. Download and install XHome APP Scan the QR code below or on the side of the box, or search for XHome in the mobile app market or App Store, then download and install the APP on your mobile phone. 2. Install the primary node ① Take out a node device from the box. Connect one end of the network cable to the Modem or broadband network port, and the other end of the network cable to one of WAN port of the node. ② Turn on the power, and the LED indicator will be solid red. After about 80 seconds, the LED indicator is flashing red, continue to wait the LED indicator change to solid green. 3. Install the secondary node ① Take out another node from the box and place it in a suitable position. Please refer to the following suggestions: ◼ Do not exceed two walls between the primary node and the secondary node, and the maximum distance should not exceed 20 meters. ◼ Keep away from interference sources such as microwave ovens, induction cookers, refrigerators, etc. ◼ Higher from the ground and less obstructions around. ② When the power is turned on, the LED indicator is solid red. After about 80 seconds, the system starts up and the LED indicator is flashing green. ③ Continue to observe the LED indicator until it changes from flashing green to solid green. ④ If the LED indicator is not solid green. Please re-select a suitable placement position to obtain the best connection quality. ◼ Wired device Internet access: please connect to the WAN ports of all nodes. ◼ Wireless device Internet access: Please connect to the wireless network marked on the sticker at the bottom of all nodes. By default, the wireless name/password of all nodes are the same. LED Indicator status description After the power is turned on, the LED indicator will be solid red (about 80 seconds), indicating that the node's system is starting. After the start is complete, the description of LED indicator’s status is as follows. Node State Description Primary Solid green Successfully connected to the Internet Flashing red Connecting to the Internet Flashing green Connecting to the secondary node Secondary Solid green Successfully connected to primary node and signal quality is good Flashing green Connecting to primary node Flashing red Failed connected to primary node Solid blue Successfully connected to primary node but signal quality is bad FAQ Q1：The device connected to node cannot access the Internet? A1：First, observe whether the LED indicator of the primary node is solid green. If not, please check whether the node's Internet access mode is set correctly. If it is correct, please contact your network operator to check whether the home network is normal. Secondly, observe whether the secondary node is solid green. If it is not, please change to a more suitable place. Q2: How to add new node? A2: Push Primary or Secondary node’s Mesh button, then push the new node’s Mesh button. If add success, the LED indicators of the two nodes change from flashing green to solid green. Q3：How to restore the factory settings of the node? A3：When the nodes are running, press and hold the reset button of the primary node with a pointed object for about 5 seconds, and release it until the LED indicator goes out. FCC Statement This equipment has been tested and found to comply with the limits for a Class B digital device, pursuant to part 15 of the FCC Rules. These limits are designed to provide reasonable protection against harmful interference in a residential installation. This equipment generates, uses and can radiate radio frequency energy and, if not installed and used in accordance with the instructions, may cause harmful interference to radio communications. However, there is no guarantee that interference will not occur in a particular installation. If this equipment does cause harmful interference to radio or television reception, which can be determined by turning the equipment off and on, the user is encouraged to try to correct the interference by one or more of the following measures: — Reorient or relocate the receiving antenna. — Increase the separation between the equipment and receiver. — Connect the equipment into an outlet on a circuit different from that to which the receiver is connected. — Consult the dealer or an experienced radio/TV technician for help. FCC Radiation Exposure Statement This device complies with FCC radiation exposure limits set forth for an uncontrolled environment. This equipment must be installed and operated in accordance with provided instructions and the antenna(s) used for this transmitter must be installed to provide a separation distance of at least 20 cm from all persons. This device complies with Part 15 of the FCC Rules. Operation is subject to the following two conditions: (1) this device may not cause harmful interference, and (2) this device must accept any interference received, including interference that may cause undesired operation. Caution! Any changes or modifications not expressly approved by the party responsible for compliance could void the user's authority to operate the equipment.

Attestation Statements (2023-9-4) TO: Federal Communications Commission Authorization and Evaluation Division 7435 Oakland Mills Road Columbia, MD 21046, USA RE: Attestation Statements Part 2.911(d)(7) request for (FCC ID: 2AW68-NM3098， Grantee FRN: 0029837143) (Shenzhen SDMC Technology Co.,Ltd.), the undersigned, hereby authorize (Lucky Cowboy Global Services, LLC) to act as our designated U.S. agent for service of process,( Shenzhen SDMC Technology Co.,Ltd.) accepts to maintain an agent for no less than one year after the grantee has terminated all marketing and importation or the conclusion of any Commission-related proceeding involving the equipment. (Lucky Cowboy Global Services, LLC) accepts the responsibility to act as designated U.S. agent for service of process. Applicant Information： Company name: Shenzhen SDMC Technology Co.,Ltd. Contact Name: Ryan Yan Address: Room 1022, Floor 10, Building A, Customs Building, No. 2, Xin'an 3rd Road, Dalang Community,Xin'an Street, Bao'an District, Shenzhen, China Telephone No: 0755-86019782 Email: [email protected] Signature [Ryan Yan] U.S. Agent Information: Company Name: Lucky Cowboy Global Services, LLC Address: 2213 S. Braeswood Blvd. #12E Houston, TX 77030 USA FRN: 0033510934 Contact Name: Louie Liu Telephone No: +1 (713) 992-3369 Email: [email protected] Signature [Louie Liu]

Shenzhen SDMC Technology Co.,Ltd. Date: 8/15/2023 Federal Communications Commissions Authorization and Evaluation Division 7435 Oakland Mills Road Columbia, MD 21046 RE: CFR 47 §2.911 (d)(5) Attestation FCC ID: 2AW68-NM3098 1.Shenzhen SDMC Technology Co.,Ltd. certifies that the equipment for which authorization is sought is not “covered” equipment prohibited from receiving an equipment authorization pursuant to section 2.903 of the FCC rules. 2.Shenzhen SDMC Technology Co.,Ltd. certifies that, as of the date of the filing of the application, the applicant is not identified on the Covered List as an entity producing “covered” equipment and is not an affiliate or subsidiary of an entity identified on the Covered List. Sincerely yours, Name: Ryan Yan Job Title: Manager Company Name: Shenzhen SDMC Technology Co.,Ltd.

Shenzhen SDMC Technology Co.,Ltd. Date: 9/7/2023 Federal Communications Commissions Authorization and Evaluation Division 7435 Oakland Mills Road Columbia, MD 21046 RE: CFR 47 §2.911 (d)(7) Agent Designation Attestation FCC ID: 2AW68-NM3098 Grantee FRN: 0029837143 Shenzhen SDMC Technology Co.,Ltd. as required by section 2.911(d)(7), designates the following agent, loc ated in the United States, for purposes of acting as the applicant’s agent for service of process. The applicant acknowledges that they will maintain an agent for no less than one year after the grantee has terminated all marketing and importation or the conclusion of any Commission-related proceeding involving the equipment. The applicant further acknowledges their responsibility under CFR 47 §2.929(c) to inform the FCC whenever the agent information changes. U.S. Agent Information: Company Name: Lucky Cowboy Global Services, LLC FCC FRN: 0033510934 Contact Person: Loue Liu Company Address: 2213 S. Braeswood Blvd. #12E Houston, TX 77030 USA Email: [email protected] Sincerely yours, Name: Ryan Yan Job Title: Manager Company Name: Shenzhen SDMC Technology Co.,Ltd.

External Photographs Project No.:4790899498.2 Page 2 of 6 This report shall not be reproduced except in full, without the written approval of UL Verification Services (Guangzhou) Co., Ltd, Song Shan Lake Branch. View of EUT-1 (Model: NM3098B) Page 3 of 6 This report shall not be reproduced except in full, without the written approval of UL Verification Services (Guangzhou) Co., Ltd, Song Shan Lake Branch. View of EUT-2 (Model: NM3098B) View of EUT-3 (Model: NM3098B) Page 4 of 6 This report shall not be reproduced except in full, without the written approval of UL Verification Services (Guangzhou) Co., Ltd, Song Shan Lake Branch. View of EUT-4 (Model: NM3098B) View of EUT-5 (Model: NM3098B) Page 5 of 6 This report shall not be reproduced except in full, without the written approval of UL Verification Services (Guangzhou) Co., Ltd, Song Shan Lake Branch. View of Adapter-6 (Model: SA12BV-120100U) View of Adapter-7 (Model: F12L33-120100SPAU) Page 6 of 6 This report shall not be reproduced except in full, without the written approval of UL Verification Services (Guangzhou) Co., Ltd, Song Shan Lake Branch. View of EUT-8 (Model: NM3098) View of EUT-9 (Model: NM3098)

Label Specifications 贴纸尺寸：64.9mm*35.5 mm 材 质：80G 铜版纸 不干胶 覆哑膜 64.9mm 35.5mm SN: xxxxxxxxxxxxxxxx MAC: xxxxxxxxxxxxx AX3000 Dual Band Mesh Router Web Access: http://sdmclogin.cn WiFi SSID: CLARO_WIFI61 Model: NM3098B Input: 12V 1A MADE IN CHINA User Name: ClaroUsuario Password: ClienteCLARO WiFi Password: ClaroI67681 FCC ID: 2AW68-NM3098 Label and location Note: 1. This would be a plastic label with a permanent adhesive. 2. The FCC label statement will include in the user manual which will print on a paper insert and sell with the device.

Internal Photographs Project No.:4790899498.2 Page 2 of 7 This report shall not be reproduced except in full, without the written approval of UL Verification Services (Guangzhou) Co., Ltd, Song Shan Lake Branch. Internal View of EUT-1 Internal View of EUT-2 Page 3 of 7 This report shall not be reproduced except in full, without the written approval of UL Verification Services (Guangzhou) Co., Ltd, Song Shan Lake Branch. Internal View of EUT-3 Internal View of EUT-4 ANT0 WIFI2.4G&5G TX&RX ANT1 WIFI2.4G&5G TX&RX ANT2 WIFI5G RX Page 4 of 7 This report shall not be reproduced except in full, without the written approval of UL Verification Services (Guangzhou) Co., Ltd, Song Shan Lake Branch. Internal View of EUT-5 Internal View of EUT-6 Page 5 of 7 This report shall not be reproduced except in full, without the written approval of UL Verification Services (Guangzhou) Co., Ltd, Song Shan Lake Branch. Internal View of EUT-7 Internal View of EUT-8 Page 6 of 7 This report shall not be reproduced except in full, without the written approval of UL Verification Services (Guangzhou) Co., Ltd, Song Shan Lake Branch. Internal View of EUT-9 (Serial model- NM3098) Internal View of EUT-10 (Serial model- NM3098) Page 7 of 7 This report shall not be reproduced except in full, without the written approval of UL Verification Services (Guangzhou) Co., Ltd, Song Shan Lake Branch. Internal View of EUT-12 (Serial model- NM3098)

The results reported herein have been performed in accordance with the laboratory’s terms of accreditation. This report shall not be reproduced except in full without the written approval of the Laboratory. The results in this report apply to the test sample(s) mentioned above at the time of the testing period only and are not to be used to indicate applicability to other similar products. FCC RF EXPOSURE REPORT For Dual Band Mesh Router, AX3000 Dual Band Mesh Router MODEL NUMBER: NM3098B, NM3098 REPORT NUMBER: 4790899498.2-RF-4 ISSUE DATE: August 10, 2023 FCC ID: 2AW68-NM3098 Prepared for Shenzhen SDMC Technology Co.,Ltd. Room 1022, Floor 10, Building A, Customs Building, No. 2, Xin'an 3rd Road, Dalang Community, Xin'an Street, Bao'an District, Shenzhen, 518000 China Prepared by UL Verification Services (Guangzhou) Co., Ltd, Song Shan Lake Branch Building 10, Innovation Technology Park, No. 1, Li Bin Road, Song Shan Lake Hi- Tech Development Zone Dongguan, 523808, People’s Republic of China Tel: +86 769 22038881 Fax: +86 769 33244054 Website: www.ul.com REPORT NO.: 4790899498.2-RF-4 Page 2 of 7 UL Verification Services (Guangzhou) Co., Ltd, Song Shan Lake Branch FORM No.: 10-SL-F0112 This report shall not be reproduced except in full, without the written approval of UL Verification Services (Guangzhou) Co., Ltd, Song Shan Lake Branch. Revision History Rev. Issue Date Revisions Revised By V0 August 10, 2023 Initial Issue REPORT NO.: 4790899498.2-RF-4 Page 3 of 7 UL Verification Services (Guangzhou) Co., Ltd, Song Shan Lake Branch FORM No.: 10-SL-F0112 This report shall not be reproduced except in full, without the written approval of UL Verification Services (Guangzhou) Co., Ltd, Song Shan Lake Branch. TABLE OF CONTENTS 1. ATTESTATION OF TEST RESULTS ................................................................................. 4 2. TEST METHODOLOGY ..................................................................................................... 5 3. FACILITIES AND ACCREDITATION ................................................................................. 5 4. REQUIREMENT ................................................................................................................. 6 REPORT NO.: 4790899498.2-RF-4 Page 4 of 7 UL Verification Services (Guangzhou) Co., Ltd, Song Shan Lake Branch FORM No.: 10-SL-F0112 This report shall not be reproduced except in full, without the written approval of UL Verification Services (Guangzhou) Co., Ltd, Song Shan Lake Branch. 1. ATTESTATION OF TEST RESULTS Applicant Information Company Name: Shenzhen SDMC Technology Co.,Ltd. Address: Room 1022, Floor 10, Building A, Customs Building, No. 2, Xin'an 3rd Road, Dalang Community, Xin'an Street, Bao'an District, Shenzhen, 518000 China Manufacturer Information Company Name: Shenzhen SDMC Technology Co.,Ltd. Address: Room 1022, Floor 10, Building A, Customs Building, No. 2, Xin'an 3rd Road, Dalang Community, Xin'an Street, Bao'an District, Shenzhen, 518000 China EUT Information EUT Name: Dual Band Mesh Router, AX3000 Dual Band Mesh Router Model: NM3098B Serial Model: NM3098 Brand: SDMC Sample Received Date: June 26, 2023 Sample Status: Normal Sample ID: 6220436 Date of Tested: July 1, 2023 to August 10, 2023 APPLICABLE STANDARDS STANDARD TEST RESULTS FCC 47CFR§2.1091 PASS KDB-447498 D01 V06 PASS Prepared By: Checked By: Kebo Zhang Denny Huang Senior Project Engineer Senior Project Engineer Approved By: Stephen Guo Operations Manager REPORT NO.: 4790899498.2-RF-4 Page 5 of 7 UL Verification Services (Guangzhou) Co., Ltd, Song Shan Lake Branch FORM No.: 10-SL-F0112 This report shall not be reproduced except in full, without the written approval of UL Verification Services (Guangzhou) Co., Ltd, Song Shan Lake Branch. 2. TEST METHODOLOGY The tests documented in this report were performed in accordance with 47 CFR FCC Part 2 Subpart J, section 2.1091 and KDB 447498 D01 General RF Exposure Guidance v06. 3. FACILITIES AND ACCREDITATION Accreditation Certificate A2LA (Certificate No.: 4102.01) UL Verification Services (Guangzhou) Co., Ltd. Song Shan Lake Branch. has been assessed and proved to be in compliance with A2LA. FCC (FCC Designation No.: CN1187) UL Verification Services (Guangzhou) Co., Ltd. Song Shan Lake Branch. Has been recognized to perform compliance testing on equipment subject to the Commission's Delcaration of Conformity (DoC) and Certification rules ISED (Company No.: 21320) UL Verification Services (Guangzhou) Co., Ltd. Song Shan Lake Branch. has been registered and fully described in a report filed with ISED. The Company Number is 21320 and the test lab Conformity Assessment Body Identifier (CABID) is CN0046. VCCI (Registration No.: G-20019, R-20004, C-20012 and T-20011) UL Verification Services (Guangzhou) Co., Ltd. Song Shan Lake Branch. has been assessed and proved to be in compliance with VCCI, the Membership No. is 3793. Facility Name: Chamber D, the VCCI registration No. is G-20019 and R-20004 Shielding Room B , the VCCI registration No. is C-20012 and T-20011 Note 1: All tests measurement facilities use to collect the measurement data are located at Building 10, Innovation Technology Park, Song Shan Lake Hi tech Development Zone, Dongguan, 523808, China Note 2: The test anechoic chamber in UL Verification Services (Guangzhou) Co., Ltd. Song Shan Lake Branch had been calibrated and compared to the open field sites and the test anechoic chamber is shown to be equivalent to or worst case from the open field site. Note 3: For below 30MHz, lab had performed measurements at test anechoic chamber and comparing to measurements obtained on an open field site. And these measurements below 30MHz had been correlated to measurements performed on an OFS. REPORT NO.: 4790899498.2-RF-4 Page 6 of 7 UL Verification Services (Guangzhou) Co., Ltd, Song Shan Lake Branch FORM No.: 10-SL-F0112 This report shall not be reproduced except in full, without the written approval of UL Verification Servi…

Text truncated - open the document above for the full version.

The results reported herein have been performed in accordance with the laboratory’s terms of accreditation. This report shall not be reproduced except in full without the written approval of the Laboratory. The results in this report apply to the test sample(s) mentioned above at the time of the testing period only and are not to be used to indicate applicability to other similar products. CFR 47 FCC PART 15 SUBPART C TEST REPORT For Dual Band Mesh Router, AX3000 Dual Band Mesh Router MODEL NUMBER: NM3098B, NM3098 REPORT NUMBER: 4790899498.2-RF-1 ISSUE DATE: August 10, 2023 FCC ID: 2AW68-NM3098 Prepared for Shenzhen SDMC Technology Co.,Ltd. Room 1022, Floor 10, Building A, Customs Building, No. 2, Xin'an 3rd Road, Dalang Community, Xin'an Street, Bao'an District, Shenzhen, 518000 China Prepared by UL Verification Services (Guangzhou) Co., Ltd, Song Shan Lake Branch Building 10, Innovation Technology Park, No. 1, Li Bin Road, Song Shan Lake Hi- Tech Development Zone Dongguan, 523808, People’s Republic of China Tel: +86 769 22038881 Fax: +86 769 33244054 Website: www.ul.com REPORT NO.: 4790899498.2-RF-1 Page 2 of 200 UL Verification Services (Guangzhou) Co., Ltd, Song Shan Lake Branch FORM NO: 10-SL-F0035 This report shall not be reproduced except in full, without the written approval of UL Verification Services (Guangzhou) Co., Ltd, Song Shan Lake Branch. Revision History Rev. Issue Date Revisions Revised By V0 August 10, 2023 Initial Issue REPORT NO.: 4790899498.2-RF-1 Page 3 of 200 UL Verification Services (Guangzhou) Co., Ltd, Song Shan Lake Branch FORM NO: 10-SL-F0035 This report shall not be reproduced except in full, without the written approval of UL Verification Services (Guangzhou) Co., Ltd, Song Shan Lake Branch. Summary of Test Results Test Item Clause Limit/Requirement Result Antenna Requirement N/A FCC Part 15.203/15.247 (c) Pass AC Power Line Conducted Emission ANSI C63.10-2013, Clause 6.2 FCC Part 15.207 Pass Conducted Output Power ANSI C63.10-2013, Clause 11.9.1.3 FCC Part 15.247 (b)(3) Pass 6dB Bandwidth ANSI C63.10-2013, Clause 11.8.1 FCC Part 15.247 (a)(2) Pass Power Spectral Density ANSI C63.10-2013, Clause 11.10.2 FCC Part 15.247 (e) Pass Conducted Band edge and spurious emission ANSI C63.10-2013, Clause 11.11 FCC Part 15.247(d) Pass Radiated Band edge and Spurious Emission ANSI C63.10-2013, Clause 11.12 & Clause 11.13 FCC Part 15.247 (d) FCC Part 15.205/15.209 Pass Duty Cycle ANSI C63.10-2013, Clause 11.6 None; for reporting purposes only. Pass *This test report is only published to and used by the applicant, and it is not for evidence purpose in China. *The measurement result for the sample received is <Pass> according to <CFR 47 FCC PART 15 SUBPART C > when <Accuracy Method> decision rule is applied. REPORT NO.: 4790899498.2-RF-1 Page 4 of 200 UL Verification Services (Guangzhou) Co., Ltd, Song Shan Lake Branch FORM NO: 10-SL-F0035 This report shall not be reproduced except in full, without the written approval of UL Verification Services (Guangzhou) Co., Ltd, Song Shan Lake Branch. CONTENTS 1. ATTESTATION OF TEST RESULTS ..................................................................................... 6 2. TEST METHODOLOGY ......................................................................................................... 7 3. FACILITIES AND ACCREDITATION ..................................................................................... 7 4. CALIBRATION AND UNCERTAINTY ................................................................................... 8 4.1. MEASURING INSTRUMENT CALIBRATION ........................................................... 8 4.2. MEASUREMENT UNCERTAINTY ............................................................................ 8 5. EQUIPMENT UNDER TEST .................................................................................................. 9 5.1. DESCRIPTION OF EUT ........................................................................................... 9 5.2. CHANNEL LIST ........................................................................................................ 9 5.3. MAXIMUM POWER ................................................................................................ 10 5.4. TEST CHANNEL CONFIGURATION ...................................................................... 10 5.5. THE WORSE CASE POWER SETTING PARAMETER .......................................... 10 5.6. WORST-CASE CONFIGURATIONS ....................................................................... 12 5.7. DESCRIPTION OF AVAILABLE ANTENNAS ......................................................... 13 5.8. SUPPORT UNITS FOR SYSTEM TEST ................................................................. 14 6. MEASURING EQUIPMENT AND SOFTWARE USED......................................................... 15 7. ANTENNA PORT TEST RESULTS ..................................................................................... 18 7.1. CONDUCTED OUTPUT POWER ........................................................................... 18 7.2. 6DB BANDWIDTH AND 99% OCCUPIED BANDWIDTH ........................................ 19 7.3. POWER SPECTRAL DENSITY .............................................................................. 21 7.4. CONDUCTED BAND EDGE AND SPURIOUS EMISSION ..................................... 23 7.5. DUTY CYCLE ......................................................................................................... 25 8. RADIATED TEST RESULTS ............................................................................................... 26 8.1. RESTRICTED BANDEDGE .................................................................................... 34 8.2. SPURIOUS EMISSIONS(1 GHZ~3 GHZ) ............................................................... 57 8.3. SPURIOUS EMISSIONS(3 GHZ~18 GHZ) ............................................................. 63 8.4. SPURIOUS EMISSIONS(9 KHZ~30 MHZ) ........................…

Text truncated - open the document above for the full version.

ShenzhenYingjiaChuangelectronictechnologyCo.,LTD http://www.szsyjc.com 第 1 页共 11 页 ContactInformation(factory): Companyaddress:buildingA.C,guangmingvalley,hongyuguangmingvalley,no.11,jiangyoumagang, shiweicommunity,matantianoffice,guangmingdistrict,shenzhen HangzhouOffice:212,BuildingB,DahuaJianghongInternationalInnovationPark,No.369,Internetof ThingsStreet,BinjiangDistrict,Hangzhou Phone+86-755-27810060/23192199;Fax:+86-0755-27810057 Companywebsite:http://www.szsyjc.comE-mail:[email protected] CUSTOMERNAME CUSTOMERP/N PARTNAME 2.4G/5.8GblackPCBInternalantenna1.13Blackline L=60mm(Applicablemodel:GM3000， NM3098,NM3098B) P/N YJC-6N060-B126 APPROVALREV. A0 DELIVERYDATE August25th,2023 PREPAREDBY YinFeijie CHECKEDBY FangWenfeng APPROVEDBY Chauhan CustomerApproved PreparedByCheckedByApprovedBy ShenzhenYingjiaChuangelectronictechnologyCo.,LTD http://www.szsyjc.com 第 2 页共 11 页 Catalogue 1、cover··········································································1 2、catalogue··········································································2 3、resume·······································································3 4、Antennaplan·································································4 5、Antennatechnicalparameters············································5 6、Environmentaltesting···············································5 7、antennaphysicalpicture············································6 8、Attachedlocationmap··················································6 9、Antennaperformancetestdiagram···················································6 10、2D.3D(2.4G/5.8G)testdata················································7-9 11、Wirespecificationparameters·······················································10 12、ROHSMaterialcontrolreport···················································11 ShenzhenYingjiaChuangelectronictechnologyCo.,LTD http://www.szsyjc.com 第 3 页共 11 页 resume： edition Contentofchangeandreasonsforchangedaterelease A/0InitialreleaseAugust25th,2023 ShenzhenYingjiaChuangelectronictechnologyCo.,LTD http://www.szsyjc.com 第 4 页共 11 页 Antennaplan： ShenzhenYingjiaChuangelectronictechnologyCo.,LTD http://www.szsyjc.com 第 5 页共 11 页 Antennatechnicalparametersandenvironmentaltesting： Electricaltechnicalparameter ElectricalSpecificationsMechanicalSpecifications FrequencyRange 2400-2500/5150-5850M Hz CableColorBlack VSWR＜1.92InputconnectorXD InputImpedance50ΩCablelength60mm DirectionAllWorkingTemperature-20°C~+70°C Gain4.5dBiWorkingHumidity20%~80% Environmentalperformancetest : ProjectTestconditionStandard Storage Conditions Intheabsenceofspecifiedtesttemperature, humidity,airpressureisasfollows:: 1.Temperatureis-30°C~+80°C 2.Relativehumidityof45%to45% 3.Airpressureis86kpato106kpa Electricaland mechanicalperformace isnormal Highandlow temperaturetest Between70°Cand-20°Cfor5loops,then1-2 hundernormalconditions,checktheappearance quality. Sizeshouldmeetthe requirementsandmeet theperformanceof mechineryand electric. Constantdampand hotresistance test 95+/-3%relativehumidity,temperaturetest: 40°C.Lasts2hafter,trytotakeoutthe determinationofelectricalproperties,within 5minaftertry1-2hunderarticlenormalthing, checktheappearancequality Sizeshouldmeetthe requirementsandmeet theperformanceof mechineryand electric. vibrationtest 10-55hz,vibrationfrequencyrangeof displacementamplitude:0.35MM,acceleration amplitude:50.0M/S,sweepcycles:30times Electricaland mechanicalperformace isnormal Falldowntest 1mhighaltitudeinaccordancewiththe perpendicularaxisfreedrop3times Electricaland mechanicalperformace isnormal ShenzhenYingjiaChuangelectronictechnologyCo.,LTD http://www.szsyjc.com 第 6 页共 11 页 Antennaphysicaldiagramandattachedlocationdiagram： Antennaperformancetestdiagram: Ante nna atta chm ent posi tion ShenzhenYingjiaChuangelectronictechnologyCo.,LTD http://www.szsyjc.com 第 7 页共 11 页 2Dand3Dtestdata(2.4G/5.8G): FrequencyEfficiency(%)Gain.(dBi) 2400MHz 63.13.12 2410MHz 64.273.02 2420MHz 65.163.15 2430MHz 65.462.88 2440MHz 68.872.85 2450MHz 67.142.9 2460MHz 69.342.91 2470MHz 70.473.06 2480MHz 69.53.19 2490MHz 71.943.28 2500MHz 65.463.57 5150MHz 63.12.82 5250MHz 62.664.2 5350MHz 62.523.29 5450MHz 59.573.44 5550MHz 62.093.42 5650MHz 59.433.36 5750MHz 60.533.57 5850MHz 59.163.85 Phi02D:Phi902DTheta902D 3D2400 ： ShenzhenYingjiaChuangelectronictechnologyCo.,LTD http://www.szsyjc.com 第 8 页共 11 页 3D2450： 3D2500： 3D5150： ShenzhenYingjiaChuangelectronictechnologyCo.,LTD http://www.szsyjc.com 第 9 页共 11 页 3D5550： 3D5850： ShenzhenYingjiaChuangelectronictechnologyCo.,LTD http://www.szsyjc.com 第 10 页共 11 页 ProductType 1.13Wire StructureDrawing StructureCharacteristics StructureItemStandardValue InnerConductor Material Silverplatedcopperwire (mm/Composition(No./mm) 7/0.08±0.005 Nom.Dia(mm)Φ0.24±0.01 Insulation MaterialFEP Nom.Dia(mm)Φ0.7±0.03 OuterConductor MaterialTinnedcopper FromWeaving Shieldingrate≧90% Nom.Dia(mm)Φ0.92±0.03 Jacket MaterialFEP Nom.Dia(mm)Φ1.13±0.05 电气性能ElectricalCharacteristics Item StandardValue Item FrequencyStandardValue Impedance（Ω）50±3 Attenuation@20 °C (dB/100m) 1GHz ≤2.23 Capacitance(pF/m)98 2GHz ≤3.15 Tensilestrengthkgf/mm² 1.76 3GHz ≤3.96 VSWR ≤1.40@0-6GHz GHz 4GHz ≤4.6 DielectricStrength（A.CV/1min) 1000 5GHz ≤5.15 （MHz） Max.oper.frequency 6000 6GHz ≤5.7 Dependability Min.BendingRadius/Singlemm4 Min.BendingRadius/Repeatedmm8 OperatingTemperature°C-20~+80 Packing PackingMode1000（m/disc)Reel TripsforUse StorageEnvironment Temperature:below30°C,humidity:20-65% TeflonShrink Insulationshrinkage≦0.2mm;Sheathshrinkage≦0.3mm Processingtemperature Undertheconditionof250°C~260°C,itcanwithstandforashorttime; Thermaldecompositionoccursabove300°C Thebestsavecycle After2months,theeffectoftinbecomesworseafter2months,butthe soonaspossibleafterpeelinginthehightemperatureandhighhumidity environmentinsummer ShenzhenYingjiaChuangelectronictechnologyCo.,LTD http://www.szsyjc.com 第 11 页共 11 页 MaterialRoHSconformitydeclarationform Thisistocertifythatthedeliverytoyourcompany'scomponents,ra…

Text truncated - open the document above for the full version.

ShenzhenYingjiaChuangelectronictechnologyCo.,LTD http://www.szsyjc.com 第 1 页共 11 页 ContactInformation(factory): Companyaddress:buildingA.C,guangmingvalley,hongyuguangmingvalley,no.11,jiangyoumagang, shiweicommunity,matantianoffice,guangmingdistrict,s…

Text truncated - open the document above for the full version.