2AW96-M700SProjector

Quick Start Guide Miroir M700S Projector 2 Your Miroir M700S Projector 3 A Audio Out (3.5mm) - (Optional) Connect an external speaker or headphones. B USB Media Reader Jack – Plug a USB stick into the port and play movies, or share pictures. C HDMI Video Input - Connect an HDMI cable to a device that supports HDMI video output. D Reset Button E Power Port - Connect included AC Adapter for power. DC In - [email protected] F RJ45 Connector - To connect to the internet G Power Button - Turn the projector on/off H Rubber Foot Pads - Provides stability and proper airflow to cooling vents. I Kickstand - To adjusting the image angle J Tripod Mount K Cooling Vent - IMPORTANT: Do not cover or block airflow to the vent. `0.15 `0.03 `0.05 `0.10 `0.3 深圳市橙子数字科技有限公司 最终版发布 初版发布 周捷 六视图 J I H `0.15 `0.03 `0.05 `0.10 `0.3 深圳市橙子数字科技有限公司 最终版发布 初版发布 周捷 六视图 K `0.15 `0.03 `0.05 `0.10 `0.3 深圳市橙子数字科技有限公司 最终版发布 初版发布 周捷 六视图 GEDFCAB A Power B Main Screen C Volume +/- D Focus Adjust E Direction F Confi rm G Back H Projector Settings Remote Control 4 Settings WLAN WLAN Mobile 4G Oce001 Oce002 PRO-xxxxxx No Internet Connection CHOOSE A NETWORK... Mobile 4G 192.168.49.1 WiFi AP Mobile 192.168.xxx.xxx WiFi AP Upgrade Settings WLAN WLAN Mobile 4G Oce001 Oce002 PRO-xxxxxx No Internet Connection CHOOSE A NETWORK... Smart View Phone Other device Select a device below to mirror your phone’s screen or play content. PRO-xxxxxx Play content Settings WLAN WLAN Mobile 4G Oce001 Oce002 PRO-xxxxxx No Internet Connection CHOOSE A NETWORK... Mobile 4G 192.168.49.1 WiFi AP Mobile 192.168.xxx.xxx WiFi AP Upgrade Settings WLAN WLAN Mobile 4G Oce001 Oce002 PRO-xxxxxx No Internet Connection CHOOSE A NETWORK... Smart View Phone Other device Select a device below to mirror your phone’s screen or play content. PRO-xxxxxx Play content Settings WLAN WLAN Mobile 4G Oce001 Oce002 PRO-xxxxxx No Internet Connection CHOOSE A NETWORK... Mobile 4G 192.168.49.1 WiFi AP Mobile 192.168.xxx.xxx WiFi AP Upgrade Settings WLAN WLAN Mobile 4G Oce001 Oce002 PRO-xxxxxx No Internet Connection CHOOSE A NETWORK... Smart View Phone Other device Select a device below to mirror your phone’s screen or play content. PRO-xxxxxx Play content Settings WLAN WLAN Mobile 4G Oce001 Oce002 PRO-xxxxxx No Internet Connection CHOOSE A NETWORK... Mobile 4G 192.168.49.1 WiFi AP Mobile 192.168.xxx.xxx WiFi AP Upgrade Settings WLAN WLAN Mobile 4G Oce001 Oce002 PRO-xxxxxx No Internet Connection CHOOSE A NETWORK... Smart View Phone Other device Select a device below to mirror your phone’s screen or play content. PRO-xxxxxx Play content Connect To Your Streaming Stick HDMI Connect To Your MacBook USB-CConnect To Your Apple Device Lightning Connect To Your Laptop HDMIConnect To Your Device HDMI Cable (Included) HDMI Cable (Included) HDMI Cable (Included) USB-C Digital AV Multiport Adapter (not included) Apple Lightning Digital AV Adapter is required for iPhone. (not included) HDMI Cable (Included) HDMI Adapter may be required for your device. (not included) USB Power Cable (if required) Connecting Your Projector with a Cable Settings WLAN WLAN Mobile 4G O  ce001 O  ce002 PRO-xxxxxx No Internet C onnection CHOOSE A NETWORK... Mobile 4G 192.168.49.1 WiFi AP Mobile 192.168.xxx.xxx WiFi AP Upgrade Settings WLAN WLAN Mobile 4G O  ce001 O  ce002 PRO-xxxxxx No Internet C onnection CHOOSE A NETWORK... Smart V iew Phone Other deviceSelect a device below to mirror your phone’ s screen or play content. PRO-xxxxxx Play c ontent IMPORTANT! Not all USB – C cables will support video. 5 A B C D H E F G 6 Zoom (under Settings) •Depending on your projector’s distance from the wall, use the zoom feature to adjust the image size. Keystone (under Settings) •The projector will auto keystone to 6-points, or you can manually adjus t under settings. Connecting Your Projector Wirelessly WIFI •Connect the M700S to your WIFI network. Open Settings, and select WIFI and follow the instructions. • Update the projector if prompted •Open the SYNQ TV App • Connect to the available streaming services (not included); a streaming service subscription is required to stream with SYNQ TV •Once you’ve logged into your streaming account, start streaming! •Live TV and Apple TV + are not supported now; please check our website for release dates. Screen Mirroring YouTube; TikTok is supported to play content. *Netflix and other streaming services are not supported •Connect your iOS, Android, Laptop, or Tablet wirelessly via the device mirroring option. •Netflix and other services do not support Screen Mirroring because of Digital Rights Management (DRM) • Local photos and videos you have taken support Screen Mirroring. •Some Apps, such as YouTube and TikTok, will support screen mirroring because they are not restricted by DRM. Adjust the Projector Image 7 Troubleshooting The image is blurry •Adjust the projected image’s focus using the remote under settings. •Check that the surface you are projecting on is smooth and non-reflective. •Check that the projector’s lens is clean and free of debris. The image is not square •Check that the projector’s lens is parallel to your projection surface and that your projection surface is flat. No sound •Check the volume control on your source device to ensure the volume is turned up. •If you are using an adapter, verify that the adapter supports audio. •Check that the HDMI cable is fully plugged into the HDMI port. No Signal Message •Check that you are using the required cable and/or adapter. • If y ou are using a digital AV adapter, check that the adapter is an authentic Apple adapter and is compatible with your model phone or tablet. • If y ou are connected to a laptop or computer, check your computer display settings to ensure a multiple display option is selected (such as “mirror these displays”). •Check tha t your source device supports HDMI video out. Projector will not power on, or stay powered on •Check that the AC Power adapter is securely plugged into the projector and the …

Text truncated - open the document above for the full version.

Telstar USA LLC Agent Authorization Company: Telstar USA LLC Address: 9817 Valley View Road,Eden Prairie, MN, US Product Name: Projector Model Number(s): M700S Product Description: Projector We authorize MiCOM Labs Inc., 575 Boulder Court, Pleasanton, California 94566, USA, to act on our behalf on all matters concerning the certification of above named equipment. We declare that MiCOM Labs Inc. is allowed to forward all information related to the approval and certification of equipment to the regulatory agencies as required and to discuss any issues concerning the approval application. Any and all acts carried out by MiCOM Labs on our behalf shall have the same effect as acts of our own. Date: Nov. 28, 2022 Signature: Name: Richard Oscar Erickson Title: CEO Company: Telstar USA LLC

Telstar USA LLC Date: Nov. 28, 2022 Offic e of Engineering Technology Federal Communications Commission 743 5 Oakland Mill s Road Columbia, MD 21046 USA Subject; Request for Confidentiality FCC ID: 2AW96-M700S To Whom It May Concern, Pursuant to the provisions of the Commission’s rules Title 47 Sections §0.457 and §0.459, we are requesting the Commission to withhold the following attachment(s) as confidential documents from public disclosure indefinitely. These documents contain detailed system and equipment descriptions and are considered as proprietary information in operation of the equipment. The public disclosure of these documents might be harmful to our company and would give competitors an unfair advantage in the market. In additional to above mentioned documents, in order to comply with the marketing regulations in Title 47 CFR §2.803 and the importation rules in Title 47 CFR §2.1204, while ensuring that business sensitive information remains confidential until the actual marketing of newly authorized devices, we request Short Term Confidentiality of the following attachment(s); External Photos Test Setup Photos Internal Photos User Manual For 45 days, pursuant to Public Notice DA 04-1705 . OR For 180 days pursuant to KDB 726920 D01. It is our understanding that all measurement test reports, FCC ID label format and correspondence during the certification review process cannot be granted as confidential documents and this information will be available for public review once the grant of equipment authorization is issued. Sincerely, Signature: Name: Richard Oscar Erickson Title: CEO Schematic Diagram Block Diagram Parts List Operational Description Tune-up Procedure FCC Software Security Requirements for UNII devices

Project No.: ZKT-221109L8361-01 FCC ID: 2AW96-M700S Project No.: ZKT-221109L8361-01 FCC ID: 2AW96-M700S Project No.: ZKT-221109L8361-01 FCC ID: 2AW96-M700S Project No.: ZKT-221109L8361-01 FCC ID: 2AW96-M700S

Project No.: ZKT-221109L8361-01 FCC ID: 2AW96-M700S Label palce SIZE:30*20mm Product name: Projector Manufacturer: Shenzhen Orange Digital Technology Co.,Ltd FCC ID: 2AW96-M700S Product Model: M700S Input: 19V 3.42A

Project No.: ZKT-221109L8361-01 FCC ID: 2AW96-M700S Project No.: ZKT-221109L8361-01 FCC ID: 2AW96-M700S Project No.: ZKT-221109L8361-01 FCC ID: 2AW96-M700S Project No.: ZKT-221109L8361-01 FCC ID: 2AW96-M700S Project No.: ZKT-221109L8361-01 FCC ID: 2AW96-M700S Project No.: ZKT-221109L8361-01 FCC ID: 2AW96-M700S BT ANT W IFI ANT2 W IFI ANT1

FCC ID: 2AW96-M700S RF Exposure Evaluation According to KDB447498D01 General RF Exposure Guidance v06 4.3.1. Standalone SAR test exclusion considerations Unless specifically required by the published RF exposure KDB procedures, standalone 1-g head or body and 10-g extremity SAR evaluation for general population exposure conditions, by measurement or numerical simulation, is not required when the corresponding SAR Exclusion Threshold condition, listed below, is satisfied. Limits According to FCC Part1.1310: The criteria listed in the following table shall be used to evaluate the environment impact of human exposure to radio frequency (RF) radiation as specified in part1.1307(b) F= Frequency in MHz Friis Formula Friis transmission formula: Pd = (Pout*G)/(4* Pi * R 2) Where Pd = power density in mW/cm2 Pout = output power to antenna in mW G = gain of antenna in linear scale Pi = 3.1416 R = distance between observation point and center of the radiator in cm Pd id the limit of MPE . If we know the maximum gain of the antenna and the total power input to the antenna, through the calculation, we will know the distance r where the MPE limit is reached. Test Result of RF Exposure Evaluation BT ANT1: 3.74dBi; 2.4G-ANT1:4.16dBi; ANT1:4.81dBi; MIMO:7.82dBi 5G-W IFI ANT1:4.68dBi; ANT2:3.67dBi ; MIMO: 7.69dBi Antenna Gain: The maximum Gain measured in fully anechoic chamber is 1.0 in linear scale. Output Power Into Antenna & RF Exposure Evaluation Distance: Measurement Data The Max Conducted Peak Output Power data refer to report Report No.: ZKT-221109L8361-01 & ZKT-221109L8361-02 & ZKT-221109L8361-03 & ZKT-221109L8361-04 BT/BLE-worst mode and channel: Test channel Output Power (dBm) Tune up tolerance (dBm) Maximum tune-up Power Calculated value (dBm) (mW) (BT) 8-DPSK Lowest channel 7.860 8±1 9 7.943 0.0037 (BLE)GFSK 5.134 6±1 7 5.012 0.0024 Limit: 1.0 EUT RF Exposure Evaluation simultaneous transmission operations According to 865664D02 2.2 d) 1): The sum of the ratios of the spatially averaged results to the applicable frequency dependent MPE limits : Simultaneous transmission mode The sum of the ratios SUM Limit BT+ BLE 0.0037+0.0024 0.0061 1.0 conclusion : 0.0061<1.0, So there is no sar requirement 2.4GW IFI worst mode and channel: Test channel Antenna Output Power (dBm) Maximum tune-up Power (dbm) Maximum tune-up Power (dbm) ANT1 ANT2 ANT1 ANT2 802.11b –2412MHz 16.821 15.569 16±1 16±1 20.01 802.11b –2437MHz 16.124 15.389 16±1 16±1 20.01 802.11b –2462MHz 16.072 15.440 16±1 16±1 20.01 Test worst case Maximum tune-up Power (dbm) Maximum tune-up Power (mW) Calculated value (mW/cm2) Limit (mW/cm2) 20.01 100.24 0.1207 1.0 Remark: 1)The Max Conducted Peak Output Power data refer to report Report No.: ZKT-221109L8361-03 2) Pd = (Pout*G)/(4* Pi * R 2 )=( 100.24*6.05)/(4*3.1415*20*20)= 0.1207, G=10 gain/10 =6.05 5GW IFI- worst mode and channel: U-NII-1 Mode Test channel Antenna Output Power (dBm) Tune up tolerance(dBm) Max Tune up (dBm) ANT1 ANT2 ANT1 ANT2 802.11n-5180MHz 8.600 8.532 8±1 8±1 12.01 802.11n-5200MHz 8.534 8.587 8±1 8±1 12.01 802.11n-5240MHz 7.800 7.783 8±1 8±1 12.01 U-NII-3 Mode Test channel Antenna Output Power (dBm) Tune up tolerance(dBm) Max Tune up (dBm) ANT1 ANT2 ANT1 ANT2 802.11n-5745MHz 10.58 9.74 10±1 10±1 14.01 802.11n -5785MHz 9.85 8.64 9±1 9±1 13.01 802.11n -5825MHz 9.16 8.94 9±1 9±1 13.01 Test worst case Maximum tune-up Power(dbm) Maximum tune-up Power(mW) Calculated value (mW/cm2) Limit (mW/cm2) 14.01 25.177 0.0294 1.0 Remark: 1)The Max Conducted Peak Output Power data refer to report Report No.: ZKT-221109L8361-04 2) Pd = (Pout*G)/(4* Pi * R 2 )=( 25.177 *5.875)/(4*3.1415*20*20)=0.0294., G=10 gain/10 =5.875 EUT RF Exposure Evaluation simultaneous transmission operations According to 865664D02 2.2 d) 1): The sum of the ratios of the spatially averaged results to the applicable frequency dependent MPE limits : Simultaneous transmission mode The sum of the ratios SUM Limit BT+2.4G W IFI + 5G W IFI 0.0061+0.1207+0.0294 0.1562 1.0 conclusion : 0.1562 < 1.0, So there is no sar requirement NOTE:1. EUT wifi-5G module & wifi-2.4G module is more than 20cm away from the human body. 2.The sum of the ratios(2.4GW IFI + 5G W IFI+BT) is less than the limit value of 1.0, so there is no sar requirement.

Project No.: ZKT-221109L8361-01 Page 1 of 77 FCC TEST REPORT FCC ID: 2AW96-M700S Report Number. ............................... : ZKT-221109L8361-01 Date of Test ..................................... : Nov. 07, 2022 -- Nov. 25, 2022 Date of issue .................................... : Nov. 25, 2022 Total number of pages ..................... : 77 Test Result ..................................... : PASS Testing Laboratory. .......................... : Shenzhen ZKT Technology Co., Ltd. Address .......................................... : 1/F, No. 101, Building B, No. 6, Tangwei Community Industrial Avenue, Fuhai Street, Bao'an District, Shenzhen, China Applicant's name ............................ : Telstar USA LLC Address .......................................... : 9817 Valley View Road,Eden Prairie, MN, US Manufacturer's name ..................... : Shenzhen Orange Digital Technology Co.,Ltd Address .......................................... : Room 2305,Building 2,Phase 6 ,Vanke Yuncheng,Tongfa South Road,Xili Community,Xili Street,Nanshan District,Shenzhen Test specification: Standard .......................................... : FCC CFR Title 47 Part 15 Subpart C Section 15.247 ANSI C63.10:2013 Test procedure................................. : KDB558074 D0115.247 Meas Guidance v 05r02 Non-standard test method ............. : N/A Test Report Form No. .................... : TRF-EL-112_V0 Test Report Form(s) Originator .... : ZKT Testing Master TRF ................................... : Dated: 2020-01-06 This device described above has been tested by ZKT, and the test results show that the equipment under test (EUT) is in compliance with the FCC requirements. And it is applicable only to the tested sample identified in the report. This report shall not be reproduced except in full, without the written approval of ZKT, this document may be altered or revised by ZKT, personal only, and shall be noted in the revision of the document. Product name .................................. : Projector Trademark ...................................... : Model/Type reference ...................... : M700S Ratings ............................................ : DC 19V/3.42A from adapter DC10.8V from battery Project No.: ZKT-221109L8361-01 Page 2 of 77 Testing procedure and testing location: Testing Laboratory .................................. : Shenzhen ZKT Technology Co., Ltd. Address ..................................................... : 1/F, No. 101, Building B, No. 6, Tangwei Community Industrial Avenue, Fuhai Street, Bao'an District, Shenzhen, China Alen He Tested by (name + signature) .................... : Joe Liu Reviewer (name + signature)..................... : Lake Xie Approved (name + signature) .................... : Project No.: ZKT-221109L8361-01 Page 3 of 77 Table of Contents Page 1. VE RSION ............................................................ 5 2. TEST SUMMARY ..................................................... 6 2.1 TEST FACILITY ......................................................... 6 2.2 MEASUREMENT UNCERTAINTY ......................................... 7 3. GENERAL INFORMATION ............................................. 8 3.1 GENERAL DESCRIPTION OF EUT ........................................ 8 3.2 Test Setup Configuration .................................................. 9 3.3 Support Equipment ....................................................... 9 3.4 Test Mode ............................................................. 10 3.5 EQUIPMENTS LIST FOR ALL TEST ITEMS ................................ 11 4. EMC EMISSION TEST ................................................ 12 4.1 Conducted emissions .................................................... 12 4.1.1 POWER LINE CONDUCTED EMISSION Limits ........................... 12 4.1.2 TEST PROCEDURE ................................................... 12 4.1.3 DEVIATION FROM TEST STANDARD ................................... 12 4.1.4 TEST SETUP ......................................................... 13 4.1.5 EUT OPERATING CONDITIONS ........................................ 13 4.1.6 Test Result ........................................................... 14 4.2 Radiated emissions ..................................................... 16 4.2.1 Radiated Emission Limits ............................................... 16 4.2.2 TEST PROCEDURE ................................................... 16 4.2.3 DEVIATION FROM TEST STANDARD ................................... 17 4.2.4 TEST SETUP ......................................................... 17 4.2.5 EUT OPERATING CONDITIONS ........................................ 18 4.2.6 TEST RESULTS ...................................................... 19 5. RADIATED BAND EMISSION MEASUREMENT .......................... 25 5.1 Test Requirement: ...................................................... 25 5.2 TEST PROCEDURE .................................................... 25 5.3 DEVIATION FROM TEST STANDARD .................................... 26 5.4 TEST SETUP .......................................................... 26 5.5 EUT OPERATING CONDITIONS ......................................... 26 5.6 TEST RESULT ......................................................... 27 6. CONDUCTED BAND EDGE AND SPURIOUS EMISSION ................... 29 6.1 Limit ................................................................... 29 6.2 Test Setup ............................................................. 29 6.3 Test procedure ......................................................... 29 6.4 DEVIATION FROM STANDARD .......................................... 29 6.5 Test Result ............................................................. 29 7.1 Test Setup ............................................................. 30 7.2 Limit ................................................................... 30 7.3 Test procedure ......................................................... 30 7.4 DEVIATION FROM STANDARD .…

Text truncated - open the document above for the full version.

www.inpaq.com.tw BT Antenna Test Report 1 Customer Shenzhen Orange Digital Project R3 Antenna Revision A1 Prepared by15502142182 Checked by15993920520 Date: 2021.04.26 www.inpaq.com.tw 1. Product Overview & Dimension 2. Test system 3. Antenna Matching Network 4. Test Result 2 Purpose This report is to measure the performance of BT antenna for R3.The antenna operating frequency at 2.4-2.5GHz, All test data are showed as below. Content www.inpaq.com.tw Sequence Number Test Itemequipment S parameterVSWR Agilent 5071C & Agilent 5062A OTA TestTRP&TIS Agilent 8960 E5515C& Agilent 4438C&CMW500 &CMW270 ETS&SATIMO Gain & Efficiency Gain & Efficiency ETS&SATIMO Agilent 5071C 3 2.Test System www.inpaq.com.tw 5 3.装配图 4 天线SS11 1  4 天线SS11 3# 5天线S61 1-2 1-3 5 天线S21S 2-3 6 天线无源效率 6 天线无源效率 8 ©2020 Be-Comfortable Technology C o. Ltd. All rights reserved. 6 天线无源效率 7 方向图(1#) Phi=0 Phi=90 Theta=90 7 方向图(2#) Phi=0 Phi=90 Theta=90 7 方向图(3#) Phi=0 Phi=90 Theta=90 8 OTA TEST www.inpaq.com.tw 6

Project No.: ZKT-221109L8361-01 FCC ID: 2AW96-M700S Project No.: ZKT-221109L8361-01 FCC ID: 2AW96-M700S