2AWC2-SRDT101NUWA Service Robot - Collibot

Label location Back Side Bottom Side

Report No.: FA3O3001-02 Page : 1 of 6 Report Version: Rev. 01 FCC RF Exposure Report FCC ID : 2AWC2-SRDT101 Equipment : NUWA Service Robot - Collibot Model No. : SR-DT101 Brand Name : NUWA ROBOTICS Applicant : NUWA ROBOTICS (HK) LIMITED TAIWAN BRANCH Address : 6F., No. 102, Dunhua N. Rd., Songshan Dist., Taipei City Standard : 47 CFR FCC Part 2.1091 Received Date : Nov. 17, 2023 Tested Date : Nov. 17 ~ Dec. 08, 2023 We, International Certification Corporation, would like to declare that the tested sample has been evaluated and in compliance with the requirement of the above standards. The test results contained in this report refer exclusively to the product. It shall not be reproduced except in full without the written approval of our laboratory. Reviewed by: Approved by: Along Chen / Assistant Manager Gary Chang / Manager Report No.: FA3O3001-02 Page : 2 of 6 Report Version: Rev. 01 Table of Contents 1 RF EXPOSURE TEST EXEMPTIONS ................................................................................................... 4 1.1 1-mW TEST EXEMPTION ..................................................................................................................... 4 1.2 SAR-BASED EXEMPTION .................................................................................................................... 4 1.3 MPE-BASED EXEMPTION .................................................................................................................... 4 1.4 DEVIATION FROM TEST STANDARD AND MEASUREMENT PROCEDURE ................................... 5 1.5 MEASUREMENT UNCERTAINTY ......................................................................................................... 5 1.6 EXEMPTION CALCULATION ................................................................................................................ 5 2 TEST LABORATORY INFORMATION ................................................................................................. 6 Report No.: FA3O3001-02 Page : 3 of 6 Report Version: Rev. 01 Release Record Report No. Version Description Issued Date FA3O3001-02 Rev. 01 Initial issue Sep. 23, 2024 Report No.: FA3O3001-02 Page : 4 of 6 Report Version: Rev. 01 1 RF Exposure Test Exemptions 1.1 1-mW TEST EXEMPTION Available maximum time-averaged power is no more than 1 mW. 1.2 SAR-BASED EXEMPTION This exemption is applicable to the frequency range between 300 MHz and 6 GHz, with test separation distances between 0.5 cm and 40 cm, and for all RF sources in fixed, mobile, and portable device exposure conditions. The maximum time-averaged power or effective radiated power (ERP), whichever is greater, ≤ Pth Pth (mW) = ERP 20cm (d/20) x d≤20cm Pth (mW) = ERP 20cm 20 cm < d ≤40cm Where = - log 10 Pth (mW) = ERP 20cm (mW) = 2040f 0.3GHz ≤ f < 1.5 GHz Pth (mW) = ERP 20cm (mW) = 3060 1.5GHz ≤ f < 6 GHz Frequency (MHz) Power Thresholds mW dBm 663 1353 31.31 699 1426 31.54 704 1436 31.57 777 1585 32.00 824 1681 32.26 902 1840 32.65 1500 ~ 6000 3060 34.86 1.3 MPE-BASED EXEMPTION For a much wider frequency range, from 300 kHz to 100 GHz, applicable for separation distances greater or equal to λ/2π, where λ is the free-space operating wavelength in meters. Radio Source Frequency Minimum Distance Threshold ERP F L MHz F H MHz λ L / 2π λ H / 2π W 0.3 - 1.34 159 m - 35.6 m 1920 R 2 1.34 - 30 35.6 m - 1.6 m 3450 R 2 /f 2 30 - 300 1.6 m - 159 mm 3.83 R 2 300 - 1500 159 mm - 31.8 mm 0.0128 R 2 f 1500 - 100000 31.8 mm - 0.5 mm 19.2 R 2 Note: R is the antenna-person separation distance. Report No.: FA3O3001-02 Page : 5 of 6 Report Version: Rev. 01 1.4 REFERENCE GUIDANCE 447498 D04 Interim General RF Exposure Guidance v01. 1.5 DEVIATION FROM TEST STANDARD AND MEASUREMENT PROCEDURE None 1.6 MEASUREMENT UNCERTAINTY The measurement uncertainties given below are based on a 95% confidence level (based on a coverage factor (k=2)). Parameters Uncertainty Conducted power ±0.808 dB Declaration of Conformity: The test results with all measurement uncertainty excluded are presented in accordance with the regulation limits or requirements declared by manufacturers. Comments and Explanations: The declared of product specification for EUT presented in the report are provided by the manufacturer, and the manufacturer takes all the responsibilities for the accuracy of product specification. 1.7 EXEMPTION CALCULATION Frequency Range (MHz) Maximum Conducted Power (dBm) Maximum Tune Up Limit (dBm) Antenna Gain (dBi) EIRP (dBm) ERP (dBm) ERP (mW) SAR-Based Exemption Thresholds (mW) Ratio Pass/ Fail 2412-2462 20.49 21 2.47 23.47 21.32 135.52 3060 0.044 Pass 5180-5240 19.30 19.5 3.16 22.66 20.51 112.46 3060 0.037 Pass 5745-5825 18.38 18.5 4.41 22.91 20.76 119.12 3060 0.039 Pass 2402-2480 (BT EDR) 11.65 12 2.47 14.47 12.32 17.06 3060 0.006 Pass 2402-2480 (BT BLE) 1.71 2 2.47 4.47 2.32 1.71 3060 0.001 Pass Note: Minimum separation distance = 20 cm. Report No.: FA3O3001-02 Page : 6 of 6 Report Version: Rev. 01 2 Test laboratory information Established in 2012, ICC provides foremost EMC & RF Testing and advisory consultation services by our skilled engineers and technicians. Our services employ a wide variety of advanced edge test equipment and one of the widest certification extents in the business. International Certification Corporation (EMC and Wireless Communication Laboratory), it is our definitive objective is to institute long term, trust-based associations with our clients. The expectation we set up with our clients is based on outstanding service, practical expertise and devotion to a certified value structure. Our passion is to grant our clients with best EMC / RF services by oriented knowledgeable and accommodating staff. Our Test sites are located at Linkou District and Kwei Shan District. Location map can be found on our website http://www.icertifi.com.tw. Linkou Kwei Shan Kwei Shan Site II Tel: 886-2-2601-1640 Tel: 886-3-271-8666 Tel: 886-3-271-8640 No.30-2, Ding Fwu Tsuen, Lin Kou District, New Taipei City, …

Text truncated - open the document above for the full version.

Report No.: FR3O3001-02AD Page : 1 of 22 Report Version: Rev. 01 FCC Test Report FCC ID : 2AWC2-SRDT101 Equipment : NUWA Service Robot - Collibot Model No. : SR-DT101 Brand Name : NUWA ROBOTICS Applicant : NUWA ROBOTICS (HK) LIMITED TAIWAN BRANCH Address : 6F., No. 102, Dunhua N. Rd., Songshan Dist., Taipei City Standard : 47 CFR FCC Part 15.247 Received Date : Nov. 20, 2023 Tested Date : Nov. 20 ~ Dec. 08, 2023 We, International Certification Corporation, would like to declare that the tested sample has been evaluated and in compliance with the requirement of the above standards. The test results contained in this report refer exclusively to the product. It shall not be reproduced except in full without the written approval of our laboratory. Reviewed by: Approved by: Along Chen / Assistant Manager Gary Chang / Manager Report No.: FR3O3001-02AD Page : 2 of 22 Report Version: Rev. 01 Table of Contents 1 GENERAL DESCRIPTION .................................................................................................................... 5 1.1 Information.............................................................................................................................................. 5 1.2 Local Support Equipment List ................................................................................................................ 8 1.3 Test Setup Chart .................................................................................................................................... 8 1.4 The Equipment List ................................................................................................................................ 9 1.5 Test Standards ..................................................................................................................................... 10 1.6 Reference Guidance ............................................................................................................................ 10 1.7 Deviation from Test Standard and Measurement Procedure ............................................................... 10 1.8 Measurement Uncertainty .................................................................................................................... 10 2 TEST CONFIGURATION ..................................................................................................................... 11 2.1 Testing Facility ..................................................................................................................................... 11 2.2 The Worst Test Modes and Channel Details ....................................................................................... 11 3 TRANSMITTER TEST RESULTS ....................................................................................................... 12 3.1 Unwanted Emissions into Restricted Frequency Bands ...................................................................... 12 3.2 Unwanted Emissions into Non-Restricted Frequency Bands .............................................................. 15 3.3 Conducted Output Power ..................................................................................................................... 16 3.4 Number of Hopping Frequency ............................................................................................................ 17 3.5 20dB and Occupied Bandwidth ............................................................................................................ 18 3.6 Channel Separation .............................................................................................................................. 19 3.7 Number of Dwell Time .......................................................................................................................... 20 3.8 AC Power Line Conducted Emissions ................................................................................................. 21 4 TEST LABORATORY INFORMATION ............................................................................................... 22 Appendix A. Unwanted Emissions into Restricted Frequency Bands Appendix B. Unwanted Emissions into Non-Restricted Frequency Bands Appendix C. Conducted Output Power Appendix D. Number of Hopping Frequency Appendix E. 20dB and Occupied Bandwidth Appendix F. Channel Separation Appendix G. Number of Dwell Time Appendix H. AC Power Line Conducted Emissions Report No.: FR3O3001-02AD Page : 3 of 22 Report Version: Rev. 01 Release Record Report No. Version Description Issued Date FR3O3001-02AD Rev. 01 Initial issue Sep. 23, 2024 Report No.: FR3O3001-02AD Page : 4 of 22 Report Version: Rev. 01 Summary of Test Results FCC Rules Test Items Measured Result 15.207 AC Power Line Conducted Emission [dBuV]: 0.354MHz 35.49 (Margin -13.38dB) - AV Pass 15.247(d) 15.209 Unwanted Emissions [dBuV/m at 3m]: 487.66MHz 42.67 (Margin -3.33dB) – PK Pass 15.247(d) Band Edge Meet the requirement of limit Pass 15.247(b)(1) Conducted Output Power Power [dBm]: 11.78 Pass 15.247(a)(1)(iii) Number of Hopping Channels Meet the requirement of limit Pass 15.247(a)(1) Hopping Channel Separation Meet the requirement of limit Pass 15.247(a)(1)(iii) Dwell Time Meet the requirement of limit Pass 15.203 Antenna Requirement Meet the requirement of limit Pass Declaration of Conformity: The test results with all measurement uncertainty excluded are presented in accordance with the regulation limits or requirements declared by manufacturers. Comments and Explanations: The declared of product specification for EUT presented in the report are provided by the manufacturer, and the manufacturer takes all the responsibilities for the accuracy of product specification. Report No.: FR3O3001-02AD Page : 5 of 22 Report Version: Rev. 01 1 General Description 1.1 Information 1.1.1 Specification of the Equipment under Test (EUT) RF General Information Frequency Range (MHz) Bluetooth Mode Ch. Frequency (MHz) Channel Number Data Rate 2400-…

Text truncated - open the document above for the full version.

INPAQ TECHNOLOGY CO., LTD 2021/01/06 UNLESS OTHER SPECIFIED TOLERANCES ON： INPAQ TECHNOLOGY CO., LTD. X＝N/A X.X＝N/A X.XX＝N/A ANGLES＝N/A HOLEDIA＝N/A SCALE：N/A UNIT：mm THIS DRAWINGS AND SPECIFICATIONS ARE THE PROPERTY OF INPAQ TECHNOLOGY CO.,LTD.AND SHALL NOT BE REPRODUCED OR USED AS THE BASIS FOR THE MANUFACTURE OR SALE OF APPARATUS OR DEVICES WITHOUT PERMISSION DRAWN BY:黃建棠 CHECKED BY:鄭榮謀 DESIGNED BY:許嘉晉 APPROVED BY:謝立庭 TITLE：Embedded Dual-Band Antenna for WA-P-LB-03-162 DOCUMENT ENS000143690 SPEC REV. NO. P1 PAGE 1 OF 6 Embedded Dual Band Wi-Fi Antenna for WA-P-LB-03-162 1. Explanation of part number : (1) (2) (3) (4) (5) (1) Product Type：Wireless Antenna (2) Material：PCB (3) Frequency：2400~2500 / 5150~5850 MHz (4) Coaxial Cable Type：Gray Cable (5) Suffix：162 2. Electrical Specification ： Those specifications were specially defined for SD1 WiFi 1 model Wi-Fi Antenna, and all characteristics were measured under the model’s handset testing jig. 2-1. 2400-2500MHz ： Characteristics Specifications Unit Outline Dimension 18x18x0.8 mm Center Frequency 2450 MHz VSWR 2 max. Polarization Linear Polarization Impedance 50 Ω Gain Peak 2.47 dBi Efficiency 61.16 % 2-2. 5150-5850MHz： Characteristics Specifications Unit Center Frequency 5500 MHz VSWR 2 max. Polarization Linear Polarization Impedance 50 Ω Gain Peak 4.31 dBi Efficiency 61.67 % W A P L B 0 3 1 6 2 INPAQ TECHNOLOGY CO., LTD 2021/01/06 UNLESS OTHER SPECIFIED TOLERANCES ON： INPAQ TECHNOLOGY CO., LTD. X＝N/A X.X＝N/A X.XX＝N/A ANGLES＝N/A HOLEDIA＝N/A SCALE：N/A UNIT：mm THIS DRAWINGS AND SPECIFICATIONS ARE THE PROPERTY OF INPAQ TECHNOLOGY CO.,LTD.AND SHALL NOT BE REPRODUCED OR USED AS THE BASIS FOR THE MANUFACTURE OR SALE OF APPARATUS OR DEVICES WITHOUT PERMISSION DRAWN BY:黃建棠 CHECKED BY:鄭榮謀 DESIGNED BY:許嘉晉 APPROVED BY:謝立庭 TITLE：Embedded Dual-Band Antenna for WA-P-LB-03-162 DOCUMENT ENS000143690 SPEC REV. NO. P1 PAGE 2 OF 6 2-3. Return loss： INPAQ TECHNOLOGY CO., LTD 2021/01/06 UNLESS OTHER SPECIFIED TOLERANCES ON： INPAQ TECHNOLOGY CO., LTD. X＝N/A X.X＝N/A X.XX＝N/A ANGLES＝N/A HOLEDIA＝N/A SCALE：N/A UNIT：mm THIS DRAWINGS AND SPECIFICATIONS ARE THE PROPERTY OF INPAQ TECHNOLOGY CO.,LTD.AND SHALL NOT BE REPRODUCED OR USED AS THE BASIS FOR THE MANUFACTURE OR SALE OF APPARATUS OR DEVICES WITHOUT PERMISSION DRAWN BY:黃建棠 CHECKED BY:鄭榮謀 DESIGNED BY:許嘉晉 APPROVED BY:謝立庭 TITLE：Embedded Dual-Band Antenna for WA-P-LB-03-162 DOCUMENT ENS000143690 SPEC REV. NO. P1 PAGE 3 OF 6 3. Antenna Drawing： 3-1 The appearance of the antenna is according to drawing Figure . 3-1-1 外觀標準:需完整無破損，不可有變形、髒污、毛邊、翹曲、裂縫、褶疊等情形。 工程圖上 號為重點尺寸標註指示 工程圖上號為量測尺寸標註指示 只需量測重點尺寸 Drawing Rev.P0 Figure 3-1-1. ITEM DESCRIPTION MATERIAL SPECIFICATION QUANTITY UNIT 1 PCB 18x18x0.8mm 1 PCS 2 Cable RF Cable1.37,LLS,Gray 1 PCS 3 Connector I-PEX MHF 4-L I-PEX Equivalent(compatible) 1 PCS 4 Adhesive 17x17x0.05,3M467 1 PCS 5 Tube O.D.1.5x20 mm 1 PCS 6 Heat-Shrink Tube O.D.1.5x10 mm , Red 1 PCS INPAQ TECHNOLOGY CO., LTD 2021/01/06 UNLESS OTHER SPECIFIED TOLERANCES ON： INPAQ TECHNOLOGY CO., LTD. X＝N/A X.X＝N/A X.XX＝N/A ANGLES＝N/A HOLEDIA＝N/A SCALE：N/A UNIT：mm THIS DRAWINGS AND SPECIFICATIONS ARE THE PROPERTY OF INPAQ TECHNOLOGY CO.,LTD.AND SHALL NOT BE REPRODUCED OR USED AS THE BASIS FOR THE MANUFACTURE OR SALE OF APPARATUS OR DEVICES WITHOUT PERMISSION DRAWN BY:黃建棠 CHECKED BY:鄭榮謀 DESIGNED BY:許嘉晉 APPROVED BY:謝立庭 TITLE：Embedded Dual-Band Antenna for WA-P-LB-03-162 DOCUMENT ENS000143690 SPEC REV. NO. P1 PAGE 4 OF 6 4. Radiation Pattern： 4-1. 2400-2500MHz： 4-2. 5150-5850MHz： INPAQ TECHNOLOGY CO., LTD 2021/01/06 UNLESS OTHER SPECIFIED TOLERANCES ON： INPAQ TECHNOLOGY CO., LTD. X＝N/A X.X＝N/A X.XX＝N/A ANGLES＝N/A HOLEDIA＝N/A SCALE：N/A UNIT：mm THIS DRAWINGS AND SPECIFICATIONS ARE THE PROPERTY OF INPAQ TECHNOLOGY CO.,LTD.AND SHALL NOT BE REPRODUCED OR USED AS THE BASIS FOR THE MANUFACTURE OR SALE OF APPARATUS OR DEVICES WITHOUT PERMISSION DRAWN BY:黃建棠 CHECKED BY:鄭榮謀 DESIGNED BY:許嘉晉 APPROVED BY:謝立庭 TITLE：Embedded Dual-Band Antenna for WA-P-LB-03-162 DOCUMENT ENS000143690 SPEC REV. NO. P1 PAGE 5 OF 6 5. 2D Radiation Pattern： 5-1. 2400-2500MHz： 5-2. 5150-5850MHz： INPAQ TECHNOLOGY CO., LTD 2021/01/06 UNLESS OTHER SPECIFIED TOLERANCES ON： INPAQ TECHNOLOGY CO., LTD. X＝N/A X.X＝N/A X.XX＝N/A ANGLES＝N/A HOLEDIA＝N/A SCALE：N/A UNIT：mm THIS DRAWINGS AND SPECIFICATIONS ARE THE PROPERTY OF INPAQ TECHNOLOGY CO.,LTD.AND SHALL NOT BE REPRODUCED OR USED AS THE BASIS FOR THE MANUFACTURE OR SALE OF APPARATUS OR DEVICES WITHOUT PERMISSION DRAWN BY:黃建棠 CHECKED BY:鄭榮謀 DESIGNED BY:許嘉晉 APPROVED BY:謝立庭 TITLE：Embedded Dual-Band Antenna for WA-P-LB-03-162 DOCUMENT ENS000143690 SPEC REV. NO. P1 PAGE 6 OF 6 6. Efficiency Table： Frequency / MHz Efficiency / dB Efficiency / % Gain / dB 2400 -2.01 62.98 2.29 2450 -1.79 66.24 2.47 2500 -2.14 61.16 2.36 5150 -2.1 61.67 3.08 5470 -2.03 62.64 3.68 5850 -2.06 62.29 4.31

INPAQ TECHNOLOGY CO., LTD 2021/01/06 UNLESS OTHER SPECIFIED TOLERANCES ON： INPAQ TECHNOLOGY CO., LTD. X＝N/A X.X＝N/A X.XX＝N/A ANGLES＝N/A HOLEDIA＝N/A SCALE：N/A UNIT：mm THIS DRAWINGS AND SPECIFICATIONS ARE THE PROPERTY OF INPAQ TECHNOLOGY CO.,LTD.AND SHALL NOT BE REPRODUCED OR USED AS THE BASIS FOR THE MANUFACTURE OR SALE OF APPARATUS OR DEVICES WITHOUT PERMISSION DRAWN BY:黃建棠 CHECKED BY:鄭榮謀 DESIGNED BY:許嘉晉 APPROVED BY:謝立庭 TITLE：Embedded Dual-Band Antenna for WA-P-LB-03-163 DOCUMENT ENS000143700 SPEC REV. NO. P1 PAGE 1 OF 6 Embedded Dual Band Wi-Fi Antenna for WA-P-LB-03-163 1. Explanation of part number : (1) (2) (3) (4) (5) (1) Product Type：Wireless Antenna (2) Material：PCB (3) Frequency：2400~2500 / 5150~5850 MHz (4) Coaxial Cable Type：Gray Cable (5) Suffix：163 2. Electrical Specification ： Those specifications were specially defined for SD1 WiFi 2 model Wi-Fi Antenna, and all characteristics were measured under the model’s handset testing jig. 2-1. 2400-2500MHz ： Characteristics Specifications Unit Outline Dimension 18x18x0.8 mm Center Frequency 2450 MHz VSWR 2 max. Polarization Linear Polarization Impedance 50 Ω Gain Peak 2.43 dBi Efficiency 60.56 % 2-2. 5150-5850MHz： Characteristics Specifications Unit Center Frequency 5500 MHz VSWR 2 max. Polarization Linear Polarization Impedance 50 Ω Gain Peak 4.41 dBi Efficiency 61.86 % W A P L B 0 3 1 6 3 INPAQ TECHNOLOGY CO., LTD 2021/01/06 UNLESS OTHER SPECIFIED TOLERANCES ON： INPAQ TECHNOLOGY CO., LTD. X＝N/A X.X＝N/A X.XX＝N/A ANGLES＝N/A HOLEDIA＝N/A SCALE：N/A UNIT：mm THIS DRAWINGS AND SPECIFICATIONS ARE THE PROPERTY OF INPAQ TECHNOLOGY CO.,LTD.AND SHALL NOT BE REPRODUCED OR USED AS THE BASIS FOR THE MANUFACTURE OR SALE OF APPARATUS OR DEVICES WITHOUT PERMISSION DRAWN BY:黃建棠 CHECKED BY:鄭榮謀 DESIGNED BY:許嘉晉 APPROVED BY:謝立庭 TITLE：Embedded Dual-Band Antenna for WA-P-LB-03-163 DOCUMENT ENS000143700 SPEC REV. NO. P1 PAGE 2 OF 6 2-3. Return loss： INPAQ TECHNOLOGY CO., LTD 2021/01/06 UNLESS OTHER SPECIFIED TOLERANCES ON： INPAQ TECHNOLOGY CO., LTD. X＝N/A X.X＝N/A X.XX＝N/A ANGLES＝N/A HOLEDIA＝N/A SCALE：N/A UNIT：mm THIS DRAWINGS AND SPECIFICATIONS ARE THE PROPERTY OF INPAQ TECHNOLOGY CO.,LTD.AND SHALL NOT BE REPRODUCED OR USED AS THE BASIS FOR THE MANUFACTURE OR SALE OF APPARATUS OR DEVICES WITHOUT PERMISSION DRAWN BY:黃建棠 CHECKED BY:鄭榮謀 DESIGNED BY:許嘉晉 APPROVED BY:謝立庭 TITLE：Embedded Dual-Band Antenna for WA-P-LB-03-163 DOCUMENT ENS000143700 SPEC REV. NO. P1 PAGE 3 OF 6 3. Antenna Drawing： 3-1 The appearance of the antenna is according to drawing Figure . 3-1-1 外觀標準:需完整無破損，不可有變形、髒污、毛邊、翹曲、裂縫、褶疊等情形。 工程圖上號為重點尺寸標註指示 工程圖上號為量測尺寸標註指示 只需量測重點尺寸 Drawing Rev.P0 Figure 3-1-1. ITEM DESCRIPTION MATERIAL SPECIFICATION QUANTITY UNIT 1 PCB 18x18x0.8mm 1 PCS 2 Cable RF Cable1.37,LLS,Gray 1 PCS 3 Connector I-PEX MHF 4-L I-PEX Equivalent(compatible) 1 PCS 4 Adhesive 17x17x0.05,3M467 1 PCS 5 Tube O.D.1.5x20 mm 1 PCS INPAQ TECHNOLOGY CO., LTD 2021/01/06 UNLESS OTHER SPECIFIED TOLERANCES ON： INPAQ TECHNOLOGY CO., LTD. X＝N/A X.X＝N/A X.XX＝N/A ANGLES＝N/A HOLEDIA＝N/A SCALE：N/A UNIT：mm THIS DRAWINGS AND SPECIFICATIONS ARE THE PROPERTY OF INPAQ TECHNOLOGY CO.,LTD.AND SHALL NOT BE REPRODUCED OR USED AS THE BASIS FOR THE MANUFACTURE OR SALE OF APPARATUS OR DEVICES WITHOUT PERMISSION DRAWN BY:黃建棠 CHECKED BY:鄭榮謀 DESIGNED BY:許嘉晉 APPROVED BY:謝立庭 TITLE：Embedded Dual-Band Antenna for WA-P-LB-03-163 DOCUMENT ENS000143700 SPEC REV. NO. P1 PAGE 4 OF 6 4. Radiation Pattern： 4-1. 2400-2500MHz： 4-2. 5150-5850MHz： INPAQ TECHNOLOGY CO., LTD 2021/01/06 UNLESS OTHER SPECIFIED TOLERANCES ON： INPAQ TECHNOLOGY CO., LTD. X＝N/A X.X＝N/A X.XX＝N/A ANGLES＝N/A HOLEDIA＝N/A SCALE：N/A UNIT：mm THIS DRAWINGS AND SPECIFICATIONS ARE THE PROPERTY OF INPAQ TECHNOLOGY CO.,LTD.AND SHALL NOT BE REPRODUCED OR USED AS THE BASIS FOR THE MANUFACTURE OR SALE OF APPARATUS OR DEVICES WITHOUT PERMISSION DRAWN BY:黃建棠 CHECKED BY:鄭榮謀 DESIGNED BY:許嘉晉 APPROVED BY:謝立庭 TITLE：Embedded Dual-Band Antenna for WA-P-LB-03-163 DOCUMENT ENS000143700 SPEC REV. NO. P1 PAGE 5 OF 6 5. 2D Radiation Pattern： 5-1. 2400-2500MHz： 5-2. 5150-5850MHz： INPAQ TECHNOLOGY CO., LTD 2021/01/06 UNLESS OTHER SPECIFIED TOLERANCES ON： INPAQ TECHNOLOGY CO., LTD. X＝N/A X.X＝N/A X.XX＝N/A ANGLES＝N/A HOLEDIA＝N/A SCALE：N/A UNIT：mm THIS DRAWINGS AND SPECIFICATIONS ARE THE PROPERTY OF INPAQ TECHNOLOGY CO.,LTD.AND SHALL NOT BE REPRODUCED OR USED AS THE BASIS FOR THE MANUFACTURE OR SALE OF APPARATUS OR DEVICES WITHOUT PERMISSION DRAWN BY:黃建棠 CHECKED BY:鄭榮謀 DESIGNED BY:許嘉晉 APPROVED BY:謝立庭 TITLE：Embedded Dual-Band Antenna for WA-P-LB-03-163 DOCUMENT ENS000143700 SPEC REV. NO. P1 PAGE 6 OF 6 6. Efficiency Table： Frequency / MHz Efficiency / dB Efficiency / % Gain / dB 2400 -2.01 62.93 2.2 2450 -1.81 65.95 2.43 2500 -2.18 60.56 2.16 5150 -2.09 61.86 3.16 5470 -1.97 63.5 3.91 5850 -2.05 62.34 4.41