2AWOI-RS1Electric Inline Skate

RS1遥控器说明书 RS1 Remote Controller User Manual 温馨提示：感谢您购买本产品！错误的操作可能造成不能正常使用，甚至损坏相关设备，我们强烈建议 您在使用设备前仔细阅读本说明书，并严格遵守规定的操作程序。我们不承担因使用本产品而引起的任何 责任，包括但不限于对附带损失或间接损失的赔偿责任；同时，我们不承担因擅自对产品进行修改所引起 的任何责任。我们有权在不经通知的情况下变更产品设计、外观、性能及使用要求。 Warm prompt：Thank you for purchasing this product! Incorrect operation may cause they cannot be used normally, even damage related equipment, we strongly recommend that you read this manual carefully before using the device, and strictly abide by the prescribed operating procedures. We assume no responsibility for the use of this product, including but not limited to liability for incidental or indirect damage；meanwhile, we assume no responsibility for unauthorized modification of the product. We have the right to change the product design, appearance, performance and use requirements without notice. 注意： 短按按键的意思是：按下开关在1秒左右就要松开； 长按按键的意思：按住按键不松开。 Attention: Short press the button means: Press the POWER button to release after 1 second； Long press the button means: Press and hold the button without releasing. 1. 规格参数： 1.Specifications： Name Specifications Parameters RS1 remote controller Battery size 502030 RS1 remote controller Capacitance 3.7V/150mA RS1 remote controller Charging time Charge 50% in 20 minutes RS1 remote controller Charging port Type-c RS1 remote controller Lanyard Support RS1 remote controller Weight 56g RS1 remote controller Communication mode 2.4G RS1 remote controller Remote control distance Open field 14M 2. 功能说明 2.Function Description 遥控器开机： 长按电源按键Power2秒，1号指示灯长亮，3.4.5.6指示灯闪烁3秒后3.4.5.6.全灭。 遥控器关机： 长按3秒电源按键Power，1号指示灯灭了后，已关机。 遥控器自动关机： 遥控器无连接滑板车，30秒自动关机;遥控器和滑板车有连接，不会自动关机，必须等待滑板车关机后 无连接状态30秒后关机， Turn on the remote controller： Short press the power button, indicator 1 will be constant on, indicator 2.3.4.5 flash for three seconds then all off. Turn off the remote controller： Long press the power button for three seconds, indicator 1 off, already turn off. Remote controller turn off automatic： Remote controller without connects the electric skateboard, will be turned off automatic after 30 seconds; When the remote controller connects the electric skateboard, will not turn off automatic, we must wait for the electric skateboard to turn off after it is disconnected for 30 seconds. 名称 规格 参数 RS1遥控器 电池尺寸 502030 RS1遥控器 电容容量 3.7V/200mA RS1遥控器 充电时间 20分钟充50% RS1遥控器 充电接口 Type-c RS1遥控器 挂绳 支持 RS1遥控器 重量 56g RS1遥控器 通讯方式 2.4G RS1遥控器 遥控距离 空旷14M 配对方式： ①首先打开滑板车电源，再长按5秒滑板车电源按键，滑板车指示灯0.5秒闪烁一次后，滑板车进入 配对模式。 ②再按下遥控器Power键2秒开机，同时按下Power键和Reverse键一秒松开，不要长时间按住。 ③遥控器1号灯闪烁，滑板车电源指示灯闪烁，此时配对成功即可使用。 注：滑板车电源按键长按，遥控器是短按。 1), Firstly turn on the power of the electric skateboard, long press the power button for five seconds, after the indicator flashes once every 0.5 seconds, the electric skateboard enters the pairing mode. 2), Press and hold the power button of the remote control for 2 seconds to turn it on,and then short press the Power button and Reverse button together and release them. Do not hold them for a long time. 3), When the indicator 1 of the remote controller flashes and the electric skateboard power indicator flashes, that means the remote controller and the electric skateboards are paired successfully. Notice：Long press the electric skateboard power button, short press the remote controller power button. 滑板车电量指示： 遥控器成功连接滑板车，可以使用，3,4,5,6指示灯表示滑板车电量，（3.4.5.6号灯常亮 “100%-75%”）电量，（3.4.5号灯常亮“75%-50%”）电量，（3.4号灯常亮“50%-25%”）（3号 灯常亮“25%-5%”）电量低于“10%-0%”3号指示灯0.5秒闪烁。 Electric skateboard power indicator： It can be used when the remote controller connects to the electric skateboard successfully, indicator 3,4,5 and 6 shows the electric skateboard power, Indicator 3,4,5,6 means 100%-75% power Indicator 3,4,5 means 75%-50% power Indicator 3,4 means 50%-25% power Indicator 3 means 25%-5% power When the indicator 3 flashes at a frequency of 0.5 seconds, means the power is less than 10% 遥控器电量指示： 遥控器开机瞬间5秒内，3,4,5,6号灯闪烁提示遥控器电量，按照，（3.4.5.6号灯闪烁5次电量 “100%-75%”）.（3.4.5号灯闪烁5次电量“75%-50%”）.（3.4号灯闪烁5次 电量“50%-25%”）（3号灯闪烁5次电量“25%-5%”）。 显示遥控器电量，当遥控器电量低于20%第2号指示灯0.5秒闪烁红色。 Remote controller power indicator： Within 5 seconds after the remote control is turned on, indicator 3,4,5,6 flashing to show the remote controller power, indicator 3,4,5,6 flash for 5 times means“100%-75%” indicator 3,4,5 flash for 5 times means“75%-50%” indicator 3,4 flash for 5 times means “50%-25%” indicator 3 flash for 5 times means“25%-5%” When the indicator 2 flashes at a frequency of 0.5 seconds, means the power is less than 20% 加速/刹车： 向前推动“滚轮”以控制滑板前进，向后拉动“滚轮”以控制滑板刹车。 Acceleration / brake： Push the "roller" forward to control the skateboard forward，Pull the "roller" backwards to control the skateboard brake 滑板车方向切换： 滑板车在静止状态，长按3秒Reverse按键切换滑板车前后方向，滑板向前方向行驶1号灯显示绿 色闪烁，滑板车向后方行驶1号灯显示红色闪烁，依次循环前后方向。 Electric skateboard direction switch： When the electric skateboard stopped, long press the Reverse button to switch the front and back direction of the electric skateboard, the electric skateboard driving forward, the indicator 1 shows green, short press the Reverse button again, the electric skateboard driving backward, the indicator 1 shows red, cycle back and forth. 滑板车速度档位切换： 在滑板车静止状态，或者在滑板车 滑行状态，短按Reverse按键切换滑板车四个档位，一档3号灯 长亮，二档4号灯长亮，三档5号灯长亮，四档6号档长亮，切换成功3秒后退出。 注意：在每个档位和每个灯长亮时，其他3个灯是不亮的，备注：一档是低速档，二档是中速档，三档是 高速经济档，四档是运动玩家暴力档。 Electric skateboard speed switch： When the electric skateboard stopped, or when the electric skateboard was sliding, short press the Reverse button to switch the four gears of the electric skateboard, first gear indicator 3 long bright, second gear indicator 4 long bright, third gear indicator 5 long bright, forth gear indicator 6 long bright, exit after 3 seconds if switch successfully, Notice：When each gear and each indicator long bright, the other 3 indicators are off, Mark：The first gear is low-speed gear, the second gear is medium-speed gear, the third gear is high-speed economic gear, the fourth gear is the violent gear of sports players. 滑板车刹车力度档位切换： 遥控器向后拉动“滚轮”不要送开，同时短按Reverse按键，切换滑板车刹车力度四个档位， 一档3号灯闪烁6次， 二档4号灯闪烁6…

Text truncated - open the document above for the full version.

Shenzhen DBS Technology Co., Ltd. Model Difference EUT NAME: Electric Inline Skate MODEL : RS1, RS2, IS-01 FCC ID: 2AWOI-RS1 All the model are the same circuit and RF module, except model names and color. Regards Sincerely Client’s signature: Client’s name / title : Zhang Mao Mei / Manager Contact information / address: A201, Yuantong Industrial Park, Building 8th, NO. 6352, Pingshan Avenue, Shatian Community, Kengzi Street, Pingshan District, Shenzhen, China

Shenzhen DBS Technology Co., Ltd. 2022.12.29 Eurofins Electrical and Electronic Testing NA, Inc. 914 W. Patapsco Avenue Baltimore, MD 21230 USA RE: CONFIDENTIALITY REQUEST FOR EUT NAME: Electric Inline Skate MODEL : RS1, RS2, IS-01 FCC ID: 2AWOI-RS1 To Whom It May Concern: This letter serves as an official request for confidentiality under sections 0.457 and 0.459 of CFR 47. We have requested that the - Block Diagram - Schematics - Operational Description required to be submitted with this application be permanently withheld from public review. The above materials contain trade secrets and proprietary information not customarily released to the public. The public disclosure of these materials may be harmful to the applicant and provide unjustified benefits to its competitors. Please contact me if there is any information you may need. Sincerely, Client’s signature: Client’s name / title : Zhang Mao Mei / Manager Contact information / address: A201, Yuantong Industrial Park, Building 8th, NO. 6352, Pingshan Avenue, Shatian Community, Kengzi Street, Pingshan District, Shenzhen, China

Shenzhen DBS Technology Co., Ltd. 2022.12.29 Eurofins Electrical and Electronic Testing NA, Inc. 914 W. Patapsco Avenue Baltimore, MD 21230 USA RE: LETTER OF AGENT AUTHORIZATION To Whom It May Concern: We, the undersigned, hereby authorize Shenzhen BCTC Testing Co., Ltd to act on our behalf in all matters relating to application for equipment authorization, including the signing of all documents relating to these matters. We also hereby certify that no party to the application authorized hereunder is subject to the denial of benefits, including FCC benefits, pursuant to Section 5301 of the Anti-Drug Abuse Act of 1988, 21 U.S.C.853(a). This agreement expires one year from the current date. Sincerely, Client’s signature: Client’s name / title : Zhang Mao Mei / Manager Contact information / address: A201, Yuantong Industrial Park, Building 8th, NO. 6352, Pingshan Avenue, Shatian Community, Kengzi Street, Pingshan District, Shenzhen, China

Report No.: BL-SZ22B0761-AA 1 / 1 EUT PHOTO Antenna

External Photos

Size:10*5mm Label Location FCC ID: 2AWOI-RS1

Internal Photos Antenna

FCC ID: 2AWOI-RS1 Portable device According to §15.247(e)(i) and §1.1307(b)(1), systems operating under the provisions of this section shall be operated in a manner that ensures that the public is not exposed to radio frequency energy level in excess of the Commission’s guidelines. According to KDB447498 D01 General RF Exposure Guidance V06 The 1-g SAR and 10-g SAR test exclusion thresholds for 100 MHz to 6 GHz at test separation distances ≤ 50 mm are determined by: [(max. power of channel, including tune-up tolerance, mW)/(min. test separation distance, mm)]·[√f(GHZ)] ≤ 3.0 for 1-g SAR and ≤ 7.5 for 10-g extremity SAR, where: • f(GHZ) is the RF channel transmit frequency in GHz • Power and distance are rounded to the nearest mW and mm before calculation • The result is rounded to one decimal place for comparison When the minimum test separation distance is < 5 mm, a distance of 5 mm is applied to determine SAR test exclusion. Modulation Channel Freq. (GHz) Conduct ed power (dBm) Conducte d power (mW) Tune-up power (dBm) Max tune-up power (dBm) Max tune-up power (mW) Distance (mm) Result calculatio n SAR Exclusion threshold SAR test exclusion GFSK 2.402 -1.22 0.76 -1±1 0.00 1.00 <5 0.30997 3.00 YES Conclusion: For the max result : 0.30997＜3.0, the SAR testing is not required.

No.：BCTC/RF-EMC-007 Page: 1 of 41 Edition：A.5 TEST REPORT Shenzhen BCTC Testing Co., Ltd. Report No.: BCTC2209830652E Applicant: Shenzhen DBS Technology Co., Ltd. Product Name: Electric Inline Skate Model/Type reference: RS1 Tested Date: 2022-10-18 to 2022-10-26 Issued Date: 2022-12-20 Report No.: BCTC2209830652E No.：BCTC/RF-EMC-007 Page: 2 of 41 Edition：A.5 FCC ID: 2AWOI-RS1 The test report is effective only with both signature and specialized stamp.This result(s) shown in this report refer only to the sample(s) tested. Without written approval of Shenzhen BCTC Testing Co., Ltd, this report can’t be reproduced except in full.The tested sample(s) and the sample information are provided by the client. Product Name: Electric Inline Skate Trademark: N/A Model/Type Ref.: RS1 RS2, IS-01 Prepared For: Shenzhen DBS Technology Co., Ltd. Address: A201, Yuantong Industrial Park, Building 8th, NO. 6352, Pingshan Avenue, Shatian Community, Kengzi Street, Pingshan District, Shenzhen, China Manufacturer: Shenzhen DBS Technology Co., Ltd. Address: A201, Yuantong Industrial Park, Building 8th, NO. 6352, Pingshan Avenue, Shatian Community, Kengzi Street, Pingshan District, Shenzhen, China Prepared By: Shenzhen BCTC Testing Co., Ltd. Address: 1-2/F., Building B, Pengzhou Industrial Park, No.158, Fuyuan 1st Road, Zhancheng, Fuhai Subdistrict, Bao'an District, Shenzhen, Guangdong, China. Sample Received Date: 2022-09-30 Sample tested Date: 2022-10-18 to 2022-10-26 Issue Date: 2022-12-20 Report No.: BCTC2209830652E Test Standards: FCC Part15.247 ANSI C63.10-2013 Test Results: PASS Remark: This is SRD-2.4GHz radio test report. Tested by: Approved by: Eric Yang/Project Handler Zero Zhou/Reviewer Report No.: BCTC2209830652E No.：BCTC/RF-EMC-007 Page: 3 of 41 Edition：A.5 Table Of Content Test Report Declaration Page 1. Version .................................................................................................................. 5 2. Test Summary ....................................................................................................... 6 3. Measurement Uncertainty ..................................................................................... 7 4. Product Information And Test Setup ..................................................................... 8 4.1 Product Information ............................................................................................... 8 4.2 Test Setup Configuration ...................................................................................... 9 4.3 Support Equipment ............................................................................................... 9 4.4 Channel List ........................................................................................................ 10 4.5 Test Mode ........................................................................................................... 10 4.6 Table of parameters of text software setting ....................................................... 10 5. Test Facility And Test Instrument Used ............................................................... 11 5.1 Test Facility ......................................................................................................... 11 5.2 Test Instrument Used .......................................................................................... 11 6. Conducted Emissions .......................................................................................... 13 6.1 Block Diagram Of Test Setup .............................................................................. 13 6.2 Limit .................................................................................................................... 13 6.3 Test procedure .................................................................................................... 13 6.4 EUT Operating Conditions .................................................................................. 13 6.5 Test Result .......................................................................................................... 14 7. Radiated Emissions ............................................................................................. 16 7.1 Block Diagram Of Test Setup .............................................................................. 16 7.2 Limit .................................................................................................................... 17 7.3 Test procedure .................................................................................................... 18 7.4 EUT operating Conditions ................................................................................... 19 7.5 Test Result .......................................................................................................... 20 8. Radiated Band Emission Measurement And Restricted Bands Of Operation ..... 24 8.1 Block Diagram Of Test Setup .............................................................................. 24 8.2 Limit .................................................................................................................... 24 8.3 Test Procedure ................................................................................................... 25 8.4 EUT Operating Conditions .................................................................................. 25 8.5 Test Result .......................................................................................................... 26 9. Power Spectral Density Test ............................................................................... 27 9.1 Block Diagram Of Test Setup .............................................................................. 27 9.2 Limit .................................................................................................................... 27 9.3 Test procedure .................................................................................................... 27 9.4 EUT …

Text truncated - open the document above for the full version.

Report No.: BL-SZ22B0761-901 Tel: +86-755-66850100 E-mail: [email protected] Page No. 1 / 13 Web: www.titcgroup.com Template No.: TRP-Passive-EN (2022-09-07) Add: Block B, 1/F, Baisha Science and Technology Park, Shahe Xi Road, Nanshan District, Shenzhen, Guangdong Province, P. R. China TEST REPORT Applicant: Shenzhen Lingyi Technology Co., Ltd. Address: 501, Dahong Innovation Science Park, No. 48, Xinyu Road, Xinqiao Street, Bao'an District, Shenzhen, China Equipment Type: Wire antenna Model Name: LYANT012-24TX Brand Name: N/A Test Standard: ANSI/IEEE Std 149-1979 Test Date: Nov. 21, 2022 Date of Issue: Nov. 28, 2022 ISSUED BY: Shenzhen BALUN Technology Co., Ltd. Tested by: Mai Jintian Checked by: Tolan Tu Approved by: Wei Yanquan (Chief Engineer) _______________ _______________ _______________ Report No.: BL-SZ22B0761-901 Tel: +86-755-66850100 E-mail: [email protected] Page No. 2 / 13 Web: www.titcgroup.com Template No.: TRP-Passive-EN (2022-09-07) Add: Block B, 1/F, Baisha Science and Technology Park, Shahe Xi Road, Nanshan District, Shenzhen, Guangdong Province, P. R. China Revision History Version Issue Date Revisions Rev. 01 Nov. 28, 2022 Initial Issue TABLE OF CONTENTS 1 GENERAL INFORMATION ........................................................................................................ 3 1.1 Test Laboratory ................................................................................................................... 3 1.2 Test Location ....................................................................................................................... 3 2 PRODUCT INFORMATION ....................................................................................................... 4 2.1 Applicant Information ........................................................................................................... 4 2.2 Manufacturer Information .................................................................................................... 4 2.3 General Description for Equipment under Test (EUT) ......................................................... 4 2.4 Ancillary Equipment ............................................................................................................. 4 2.5 Technical Information .......................................................................................................... 4 3 SUMMARY OF TEST RESULTS ............................................................................................... 5 3.1 Test Standards .................................................................................................................... 5 3.2 Test Verdict ......................................................................................................................... 5 3.3 Test Uncertainty .................................................................................................................. 5 4 GENERAL TEST CONFIGURATIONS ...................................................................................... 6 4.1 Test Condition ..................................................................................................................... 6 4.2 Test Equipment List ............................................................................................................. 6 4.3 Test Setup ........................................................................................................................... 7 ANNEX A TEST RESULTS ........................................................................................................... 8 A.1 Gain and Efficiency ............................................................................................................. 8 ANNEX B RADIATION PATTERN ................................................................................................ 9 ANNEX C TEST SETUP PHOTOS ............................................................................................. 12 ANNEX D EUT PHOTO .............................................................................................................. 12 Report No.: BL-SZ22B0761-901 Tel: +86-755-66850100 E-mail: [email protected] Page No. 3 / 13 Web: www.titcgroup.com Template No.: TRP-Passive-EN (2022-09-07) Add: Block B, 1/F, Baisha Science and Technology Park, Shahe Xi Road, Nanshan District, Shenzhen, Guangdong Province, P. R. China 1 GENERAL INFORMATION 1.1 Test Laboratory Name Shenzhen BALUN Technology Co., Ltd. Address Block B, 1/F, Baisha Science and Technology Park, Shahe Xi Road, Nanshan District, Shenzhen, Guangdong Province, P. R. China Phone Number +86 755 6685 0100 1.2 Test Location Name Shenzhen BALUN Technology Co., Ltd. Location Block B, 1/F, Baisha Science and Technology Park, Shahe Xi Road, Nanshan District, Shenzhen, Guangdong Province, P. R. China 1/F, Building B, Ganghongji High-tech Intelligent Industrial Park, No. 1008, Songbai Road, Yangguang Community, Xili Sub-district, Nanshan District, Shenzhen, Guangdong Province, P. R. China Report No.: BL-SZ22B0761-901 Tel: +86-755-66850100 E-mail: [email protected] Page No. 4 / 13 Web: www.titcgroup.com Template No.: TRP-Passive-EN (2022-09-07) Add: Block B, 1/F, Baisha Science and Technology Park, Shahe Xi Road, Nanshan District, Shenzhen, Guangdong Province, P. R. China 2 PRODUCT INFORMATION 2.1 Applicant Information Applicant Shenzhen Lingyi Technology Co., Ltd. Address 501, Dahong Innovation Science Park, No. 48, Xinyu Road, Xinqiao Street, Bao'an District, Shenzhen, China 2.2 Manufacturer Information Manufacturer Shenzhen Lingyi Technology Co., Ltd. Address 501, Dahong Innovation Science Park, No. 48, Xinyu Road, Xinqiao Street, Bao'an District, Shenzhen, China 2.3 General Description for Equipment under Test (EUT) EUT Name Wire antenna Model Name Under Test LYANT012-24TX Antenna Type Wire antenna Dimensions 54.9*0.9 mm 2.4 Ancillary Equipment Note: Not applicable. 2.5 Technical Information Test Frequencies 2400MHz, 2410MHz, 2420MHz, 2430MHz, 2440M…

Text truncated - open the document above for the full version.

Report No.: BL-SZ22B0761-AO 1 / 1 TEST SETUP PHOTOS

Conducted Emissions Radiated Measurement Photos