2AWYK-TP2Pocket Thermal Printer

Quick start guide Star machine Due to product updates, some details of this document may not match the product, please prevail in kind! The manufacturer has the right to modify the content of this document without prior notice! Service Information Customer service line: 0756-2897617 Official website: www.starpany.cn Manufacturer: Zhuhai yike intelligent technology co., ltd. Manufacturer Address: 307-2, Zhonglixing Building, No. 4 Xingguo Street, Xiangzhou District, Zhuhai Printer cleaning The printer should be cleaned in a timely manner when the printer: 1, The printing is not clear; 2, The printed page is not clear in the vertical direction; The cleaning steps for the print head are as follows: 1. Turn off the printer power, open the top cover, and remove the paper if there is paper; 2. If you have just finished printing, you should wait for the print head to cool completely. 3. Use a soft cotton cloth and absolute ethanol (should be wrung out) to wipe off the dust and stain on the surface of the thermal head of the print head; 4. After waiting for the absolute evaporation of absolute ethanol, close the upper cover and re-test the machine to print; Statement This product is a Class A product and may cause radio interference in a living environment. In this case, the customer may be required to take practical measures to interfere with it. Precautions for use Do not immerse the printer in water or expose it to rain, otherwise the printer may be damaged. Do not open the paper compartment cover during printing, as this may cause the printer to malfunction. When printing using Bluetooth, the distance during printingcannot exceed 10 meters, otherwise it may cause garbled printing or unprintable. Although the printer can operate stably from 0 ° C to 45 ° C, excessive ambient temperature (45 ° C) or too low ambienttemperature (0 ° C) can result in reduced print quality. Using poor quality paper or paper that has been stored fortoo long may result in reduced print quality or even damage to the printer. The printer tries to use up and recharge the battery before charging, which can effectively guarantee the battery life. Caveat This product has a built-in lithium battery, do not use it in an environment where the temperature is higher than 45 °C, do not place it near open flames or other heat sources, do not place it in hot sunlight, otherwise it may cause an explosion or fire hazard. Do not disassemble and replace the battery, if you replace the battery, you must use the same size battery, otherwise there is a danger of explosion. Used batteries are recycled or disposed of when in accordance with local regulations and product instruction manuals. Note that the thermal head of the print head is a hot component. It is strictly forbidden to touch the thermal sensorpart during printing or at the end of printing! Note that the paper exit tearing blade is sharp, please be careful not to touch! FCC Statement Any Changes or modifications not expressly approved by the party responsible for compliance could void the user's authority to operate the equipment. This equipment has been tested and found to comply with the limits for a Class B digital device, pursuant to Part 15 of the FCC Rules. These limits are designed to provide reasonable protection against harmful interference in a residential installation. This equipment generates uses and can radiate radio frequency energy and, if not installed and used in accordance with the instructions, may cause harmful interference to radio communications. However, there is no guarantee that interference will not occur in a particular installation. If this equipment does cause harmful interference to radio or television reception, which can be determined by turning the equipment off and on, the user is encouraged to try to correct the interference by one or more of the following measures: -- Reorient or relocate the receiving antenna. -- Increase the separation between the equipment and receiver. -- Connect the equipment into an outlet on a circuit different from that to which the receiver is connected. -- Consult the dealer or an experienced radio/TV technician for help. This device complies with part 15 of the FCC Rules. Operation is subject to the following two conditions: (1) This device may not cause harmful interference, and (2) this device must accept any interference received, including interference that may cause undesired operation. Changes or modifications not expressly approved by the party responsible for compliance could void the user's authority to operate the equipment. ThedevicehasbeenevaluatedtomeetgeneralRF exposurerequirement. Thedevicecanbeusedinportableexposurecondition withoutrestriction. Product introduction Product Name: Star Machine Charging input: 5V 1A Battery: Built-in7.4V/1000mAh lithium battery Printing method: thermal printing Product Size: 86x86x41.2mm Print speed: MAX 9mm/s Supplies speciflcations: 57x30mm Working environment: Temperatture: 0~45°C Humidity: 10~80% operating system: Android/IOS Key Functions Power switch USB interface Power switch USB interface ·Perss and hold for 2 seconds to turn on or off; ·double click to find the QR code. ·Charge only Note: lf you use the device for the first time or if you are idle for a long time,you may not be able to turn it on because the battery is low. Please charge it for at least half on hour before turning it on! Open key indicator status At boot time Steady on: Normal state; Fast flash: Printer is abnormal When shutting down Slow flashing: Charging, full backlight 3. Open the APP, scan the QR code printed in step 1, and connect to Bluetooth. If the connection is successful, you can use APP to print. Cover open button Download on the App Store GET IT ON Google Play Download APP Installation steps 1. the first use, long press the star machine to open the key 2 seconds to boot, double-click to open the key after booting, the star opportunity automatically print out the QR code. 2. Sear…

Text truncated - open the document above for the full version.

FCC ID: 2AWYK-TP2 Zhuhai Xprinter Electronics Technology Co., Ltd. Model Difference All models have same circuits diagram of Bluetooth module PCB, RF Chip constructionl; All models have same circuits diagram of Power. Sincerely, Name: Zhang Hua / Manager Company: Zhuhai Xprinter Electronics Technology Co., Ltd. Address: 5F,1st Building,613 Huawei Road, Qianshan Industrial Park, Xiangzhou District, Zhuhai City, Guangdong Province, China. Phone: 0756-3893087 Fax: 0756-3893230 E-Mail: [email protected] Mode List TP1, TP2, TP3, TP4, TP5, TP6, TP7, TP8, LP1, LP2, LP3, LP4, LP5, LP6, LP7, LP8, CP1, CP2, CP3, CP4, CP5, CP6, CP7, CP8, TRP1, TRP2, TRP3, TRP4, STAR1, Starpany1, Starpany-1, HP1, HSP1, X1, X2, X3, X5, X6

TOTEM ACOUSTIQUE INC. for Certification Service in USA Federal Communication Commission Equipment Authorization Division, Application Processing Branch 7435 Oakland Mills Road Columbia, MD 21046 <2021-02-25> TO WHOM IT MAY CONCERN Pursuant to Paragraphs §0.457 and 0.459 of the Commission’s Rules (47 C.F.R.) and Section §552(b)(4) of the Freedom of Information Act, we requests confidentiality for the following products: FCC ID Model name 2AWYK-TP2 TP2 For the product stated above, we request that the following information be held confidential; Exhibits Long-Term Confidentiality Short-Term Confidentiality Short-Term Confidentiality Days External Photos Internal Photos Block Diagram Schematics Test Setup Photos User’s Manual Parts List Tune Up Operational Descriptions The long-term confidentiality exhibits contain our trade secrets and proprietary information that could be of benefit to our competitors. The short-term confidentiality on the basis of ensuring that business sensitive information remains confidential until the actual marketing of our new device. If you have any questions, please feel free to contact me at the address shown below. Sincerely, ------------------------------------ Name: Zhang Hua / Manager Company: Zhuhai Xprinter Electronics Technology Co., Ltd. Address: 5F,1st Building,613 Huawei Road, Qianshan Industrial Park, Xiangzhou District, Zhuhai City, Guangdong Province, China. Phone: 0756-3893087 Fax: 0756-3893230 E-Mail: [email protected]

Zhuhai Xprinter Electronics Technology Co., Ltd. 5F,1st Building,613 Huawei Road, Qianshan Industrial Park, Xiangzhou District, Zhuhai City, Guangdong Province, China Tel: 0756-3893087 Fax: 0756-3893230 Federal Communications Commission Authorization and Evaluation Division Equipment Authorization Branch 7435 Oakland Mills Road Columbia, MD 21046 2021/02/25 To whom it may concern: We, the undersigned, hereby authorize Eurofins Product Service GmbH to act on our behalf in all matters relati ng to applications for equipment authorization FCC ID: [2AWYK-TP2] including the signing of all documents related to these matters. Any and all acts carried out by Eurofins Product Service GmbH on our behalf shall have the same effect as acts of our own. We also hereby certify that no party to this application is subject to a denial of benefits, including FCC benefits, pursuant to Section 5301 of the Anti-Drug Abuse Act of 1988, 21 U.S.C. 862. Sincerely, Name: Zhang Hua / Manager Company: Zhuhai Xprinter Electronics Technology Co., Ltd. Address: 5F,1st Building,613 Huawei Road, Qianshan Industrial Park, Xiangzhou District, Zhuhai City, Guangdong Province, China. Phone: 0756-3893087 Fax: 0756-3893230 E-Mail: [email protected]

FCC ID:2AWYK-TP2 FCC ID:2AWYK-TP2 FCC ID:2AWYK-TP2 FCC ID:2AWYK-TP2

FCC IDD Loocattionn

FCC ID: 2AWYK-TP2 FCC ID: 2AWYK-TP2 BT ANT FCC ID: 2AWYK-TP2

RF Exposure evaluation FCC ID: 2AWYK-TP2 1.1. Applicable Standard According to §1.1307(b)(1), systems operating under the provisions of this section shall be operated in a manner that ensures that the public is not exposed to radio frequency energy level in excess of the Commission’s guidelines. According to §1.1310 and §2.1093 RF exposure is calculated. KDB447498 v06: Mobile and Portable Devices RF Exposure Procedures and Equipment Authorization Policies. 1.2. Requirement According to KDB447498 D01 General RF Exposure Guidance v06 Section 4.3.1 Standalone SAR test exclusion considerations: “Unless specifically required by the published RF exposure KDB procedures, standalone 1-g head or body and 10-g extremity SAR evaluation for general population exposure conditions, by measurement or numerical simulation, is not required when the corresponding SAR Test Exclusion Threshold condition, listed below, is satisfied. These test exclusion conditions are based on source-based time-averaged maximum conducted output power of the RF channel requiring evaluation, adjusted for tune-up tolerance, and the minimum test separation distance required for the exposure conditions.22 The minimum test separation distance is determined by the smallest distance from the antenna and radiating structures or outer surface of the device, according to the host form factor, exposure conditions and platform requirements, to any part of the body or extremity of a user or bystander (see 5) of section 4.1). To qualify for SAR test exclusion, the test separation distances applied must be fully explained and justified by the operating configurations and exposure conditions of the transmitter and applicable host platform requirements, typically in the SAR measurement or SAR analysis report, according to the required published RF exposure KDB procedures. When no other RF exposure testing or reporting is required, a statement of justification and compliance must be included in the equipment approval, in lieu of the SAR report, to qualify for the SAR test exclusion. When required, the device specific conditions described in the other published RF exposure KDB procedures must be satisfied before applying these SAR test exclusion provisions; for example, handheld PTT two-way radios, handsets, laptops & tablets etc.23 “ [(max. power of channel, including tune-up tolerance, mW)/ (min. test separation distance, mm)] · [√f (GHz)] ≤ 3.0 for 1-g SAR and ≤ 7.5 for 10-g extremity SAR, where: • f (GHz) is the RF channel transmit frequency in GHz • Power and distance are rounded to the nearest mW and mm before calculation • The result is rounded to one decimal place for comparison • 3.0 and 7.5 are referred to as the numeric thresholds in the step 2 below The test exclusions are applicable only when the minimum test separation distance is ≤ 50 mm and for transmission frequencies between 100 MHz and 6 GHz. When the minimum test separation distance is < 5 mm, a distance of 5 mm according to 5) in section 4.1 is applied to determine SAR test exclusion. 1.3. Manufacturing tolerance 2.1. Evaluation Result Band/ Mode f (GHz) Antenna Distance (mm) RF output power (including tune-up tolerance) SAR Test Exclusion Threshold SAR Test Exclusion dBm mW BT(BLE) 2.402 5 5 3.162 0.980<3.0 Yes BT(EDR) 2.480 5 5 3.162 0.996<3.0 Yes Note: Result=P F /D P=Maximum turn-up power in mW F=Channel frequency in GHz D=Mininmun test separation distance in mm 3.1. Conclusion The measurement results comply with the FCC Limit per 47 CFR 2.1093 for the uncontrolled RF Exposure and SAR Exclusion Threshold per KDB 447498 v06, No SAR is required. BLE GFSK Channel Channel 00 Channel 19 Channel 39 Target (dBm) 4.0 4.0 4.0 Tolerance ±(dB) 1.0 1.0 1.0 EDR GFSK Channel Channel 00 Channel 39 Channel 78 Target (dBm) 4.0 4.0 4.0 Tolerance ±(dB) 1.0 1.0 1.0 π/4 DQPSK (Peak) Channel Channel 00 Channel 39 Channel 78 Target (dBm) 4.0 4.0 4.0 Tolerance ±(dB) 1.0 1.0 1.0 8DPSK (Peak) Channel Channel 00 Channel 39 Channel 78 Target (dBm) 4.0 4.0 4.0 Tolerance ±(dB) 1.0 1.0 1.0

Page1of32ReportNo.:UNIA21020102ER-01 FCCRADIOTESTREPORT FCCID:2AWYK-TP2 Product ： PocketThermalPrinter TradeName ：xprinter ModelName：TP2 SerialModel ： Seemodellistonpage6ofthereport. ReportNo.： UNIA21020102ER-01 Preparedfor ZhuhaiXprinterElectronicsTechnologyCo.,Ltd. 5F,1 st Building,613HuaweiRoad,QianshanIndustrialPark, XiangzhouDistrict,ZhuhaiCity,GuangdongProvince,China. Preparedby ShenzhenUnitedTestingTechnologyCo.,Ltd. 2F,AnnexBldg,JiahuangyuanTechPark,#365Baotian1Rd,Tiegang Community,XixiangStr,Bao'anDistrict,Shenzhen,China Page2of32ReportNo.:UNIA21020102ER-01 TESTRESULTCERTIFICATION Applicant’sname....................: ZhuhaiXprinterElectronicsTechnologyCo.,Ltd. Address......................................: 5F,1 st Building,613HuaweiRoad,QianshanIndustrialPark, XiangzhouDistrict,ZhuhaiCity,GuangdongProvince,China. Manufacture'sName .............. : ZhuhaiXprinterElectronicsTechnologyCo.,Ltd. Address ...................................... : 5F,1 st Building,613HuaweiRoad,QianshanIndustrialPark, XiangzhouDistrict,ZhuhaiCity,GuangdongProvince,China. Productdescription Productname...............................: PocketThermalPrinter TradeMark.................................: xprinter Modeland/ortypereference . : TP2(Seemodellistonpage6ofthereport.) Standards..................................: FCCRulesandRegulationsPart15SubpartCSection15.247, ANSIC63.10:2013 ThisdevicedescribedabovehasbeentestedbyShenzhenUnitedTestingTechnology Co.,Ltd.,andthetestresultsshowthattheequipmentundertest(EUT)isincompliance withtheFCCrequirements.Anditisapplicableonlytothetestedsampleidentifiedinthe report. Thisreportshallnotbereproducedexceptinfull,withoutthewrittenapprovalofUNI,this documentmaybealteredorrevisedbyShenzhenUnitedTestingTechnologyCo.,Ltd., personnelonly,andshallbenotedintherevisionofthedocument. DateofTest ............................................... : Date(s)ofperformanceoftests ............... :Jan.26~Feb.28,2021 DateofIssue..............................................:Mar.01,2021 TestResult..................................................:Pass Testedby: Bobliao/Editor Reviewer: Kahnyang/Supervisor Approved&AuthorizedSigner: Liuze/Manager Page3of32ReportNo.:UNIA21020102ER-01 TableofContentsPage 1.TESTSUMMARY...................................................................................................................5 1.1TESTPROCEDURESANDRESULTS....................................................................................5 1.2TESTFACILITY............................................................................................................................5 1.3MEASUREMENTUNCERTAINTY............................................................................................5 2.GENERALINFORMATION ................................................................................................... 6 2.1GENERALDESCRIPTIONOFEUT.........................................................................................6 2.2CarrierFrequencyofChannels.................................................................................................7 2.3OperationofEUTduringtesting................................................................................................7 2.4DESCRIPTIONOFTESTSETUP.............................................................................................7 2.5MEASUREMENTINSTRUMENTSLIST..................................................................................8 3.CONDUCTEDEMISSIONSTEST.......................................................................................9 3.1ConductedPowerLineEmissionLimit ..................................................................................... 9 3.2TestSetup ..................................................................................................................................... 9 3.3TestProcedure ............................................................................................................................. 9 3.4TestResult .................................................................................................................................... 9 4.RADIATEDEMISSIONTEST.............................................................................................12 4.1RadiationLimit...........................................................................................................................12 4.2TestSetup...................................................................................................................................12 4.3TestProcedure...........................................................................................................................13 4.4TestResult..................................................................................................................................13 5.BANDEDGE ......................................................................................................................... 18 5.1Limits...........................................................................................................................................18 5.2TestProcedure...........................................................................................................................18 5.3TestResult..................................................................................................................................18 6.OCCUPIEDBANDWIDTHMEASUREMENT..................................................................19 6.1TestLimit ..................................................................................................................................... 19 6.2TestProcedure ........................................................................................................................... 19 6.3MeasurementEquipmentUsed ............................................................................................... 19 6.4TestResult ..............................................…

Text truncated - open the document above for the full version.

FCC ID:2AWYK-TP2 RadiatedEmission(Below 1G) Radiated Emission (Above 1G) FCC ID:2AWYK-TP2 Conducted Emission