2AWYKXP-P501APortable thermal receipt printer, Portable thermal label printer

the printer enters the working state,and the power green indicator is on. Printer 1PC Data cable 1PC Battery 1PC User manual 1PC Paper roll 1ROLL Printer Battery User manual Paper roll Data cable Button name,Indicator Light and Buzzer function: Power button a.Turn on: Press and hold the power button 2 seconds when the power is off, b.Turn off: Press and hold the power button 3 seconds during the power-on state,the printer power is off,and all the indicators are off. Battery housing 25 seconds after the printer’s green indicator flashes and the buzzer rings then release the FEED button.At this point,the initialization has been completed.Press the POWER button again to start up and work normally. 2 Print-head cleaning: Timely clear printer-head in one of the below cases: 1. Unclear printing. 2. Unclear vertical column in printing paper. 3. Loud noise when feeding. Cleaning steps are as follows: 1. Turn off the printer and open the top cover. Remove the paper if any. 2.Temperature of print-head can be very high right after finishing the printing task. 4.Turn on the printer and continue print task after the absolute ethyl Then printer self-test page. 1.Please make sure power off when maintaining printer. 2.Don’t touch or scratch printing head surface by hands or metal materials. 3.Avoid using gasoline, acetone or other organic solvent. alcohol completely volatilized. Please clean print-head after it cools down to environment temperature. 3. Clean the thermal elements of thermal head with a soft cotton cloth moistened with absolute ethyl alcohol. 4. Close the top cover after the absolute ethyl alcohol completely volatilized. Power Button Bluetooth Indicator STATUS Indicator FEED Button Power Indicator Power Indicator Bluetooth Indicator STATUS Indicator Buzzer Out of paper and overheating,the buzzer sounds every 2 seconds. Bluetooth connection :The buzzer rings once. Press this button to feed paper.If you press this button for a long time, the paper will be fed continuously. When the red light goes out,indicating the battery is full. The green light indicates the starting state,and the red light indicates the charging state. Green light means bluetooth connection;Green light goes out means bluetooth is disconnected. Red light is always on and buzzes,the printer is in the state of paper shortage;The red light goes out after the paper is checked. Interface USB Interface USB can communicate and transmit data; Rechargeable:recommended charging power 5V/2A (sold without power adapter). Cautions: 1.The printer can only work with the dedicated battery & power adapter. 2.If the printer will not be used for a long period of time, the battery must be 3.The fluid of battery used in the printer is caustic. If accidentally the battery 5. Although the printer can work in environment temperature between 0°C to 40°C, 4.The printer must not be put into water or exposed to rain. Otherwise, it may Otherwise, it may cause harm to the printer. taken out of the printer. Otherwise, it may cause battery leakage. leaks and the fluid is put on skin or clothes, please flush with running water immediately. And if the fluid gets into eyes, please go to hospital immediately. cause harm to the printer. it may affect printing quality if environment temperature is too low or too high. Federal Communications Commission Notice This device complies with Part 15 of the FCC Rules and with Industry Canada licence-exempt RSS standard(s).Operation is subject to the following two conditions: this device may not cause harmful interference, and (2) this device must accept any interference received, including interference that may cause undesired operation. Any Changes or modifications not expressly approved by the party responsible for compliance could void the user's authority to operate the equipment. Note: This equipment has been tested and found to comply with the limits for a Class B digital device, pursuant to part 15 of the FCC Rules. These limits are designed to provide reasonable protection against harmful interference in a residential installation. This equipment generates uses and can radiate radio frequency energy and, if not installed and used in accordance with the instructions, may cause harmful interference to radio communications. However, there is no guarantee that interference will not occur in a particular installation. If this equipment does cause harmful interference to radio or television reception, which can be determined by turning the equipment off and on, the user is encouraged to try to correct the interference by one or more of the following measures: -Reorient or relocate the receiving antenna. -Increase the separation between the equipment and receiver. -Connect the equipment into an outlet on a circuit different from that to which the receiver is connected. -Consult the dealer or an experienced radio/TV technician for help. ThedevicehasbeenevaluatedtomeetgeneralRFexposure requirement.Thedevicecanbeusedinportable exposurecondition withoutrestriction. 6

TOTEM ACOUSTIQUE INC. for Certification Service in USA Federal Communication Commission Equipment Authorization Division, Application Processing Branch 7435 Oakland Mills Road Columbia, MD 21046 <2020-07-28> TO WHOM IT MAY CONCERN Pursuant to Paragraphs §0.457 and 0.459 of the Commission’s Rules (47 C.F.R.) and Section §552(b)(4) of the Freedom of Information Act, we requests confidentiality for the following products: FCC ID Model name 2AWYKXP-P501A XP-P501A For the product stated above, we request that the following information be held confidential; Exhibits Long-Term Confidentiality Short-Term Confidentiality Short-Term Confidentiality Days External Photos Internal Photos Block Diagram Schematics Test Setup Photos User’s Manual Parts List Tune Up Operational Descriptions The long-term confidentiality exhibits contain our trade secrets and proprietary information that could be of benefit to our competitors. The short-term confidentiality on the basis of ensuring that business sensitive information remains confidential until the actual marketing of our new device. If you have any questions, please feel free to contact me at the address shown below. Sincerely, ------------------------------------ Name: Zhang Hua / Manager Company: Zhuhai Xprinter Electronics Technology Co., Ltd. Address: 5F,1st Building,613 Huawei Road, Qianshan Industrial Park, Xiangzhou District, Zhuhai City, Guangdong Province, China. Phone: 0756-3893087 Fax: 0756-3893230 E-Mail: [email protected]

Zhuhai Xprinter Electronics Technology Co., Ltd. 5F,1st Building,613 Huawei Road, Qianshan Industrial Park, Xiangzhou District, Zhuhai City, Guangdong Province, China Tel: 0756-3893087 Fax: 0756-3893230 Federal Communications Commission Authorization and Evaluation Division Equipment Authorization Branch 7435 Oakland Mills Road Columbia, MD 21046 2020/07/28 To whom it may concern: We, the undersigned, hereby authorize Eurofins Product Service GmbH to act on our behalf in all matters relati ng to applications for equipment authorization FCC ID: [2AWYKXP-P501A] including the signing of all documents related to these matters. Any and all acts carried out by Eurofins Product Service GmbH on our behalf shall have the same effect as acts of our own. We also hereby certify that no party to this application is subject to a denial of benefits, including FCC benefits, pursuant to Section 5301 of the Anti-Drug Abuse Act of 1988, 21 U.S.C. 862. Sincerely, Name: Zhang Hua / Manager Company: Zhuhai Xprinter Electronics Technology Co., Ltd. Address: 5F,1st Building,613 Huawei Road, Qianshan Industrial Park, Xiangzhou District, Zhuhai City, Guangdong Province, China. Phone: 0756-3893087 Fax: 0756-3893230 E-Mail: [email protected]

FCC ID: 2AW YKXP-P501A Zhuhai Xprinter Electronics Technology Co., Ltd. Model Difference All models have same circuits diagram of Bluetooth module PCB, RF Chip constructionl; All models have same circuits diagram of Power ; Product's power amplifier board, control board and rated power are different. Sincerely, Name: Zhang Hua / Manager Company: Zhuhai Xprinter Electronics Technology Co., Ltd. Address: 5F,1st Building,613 Huawei Road, Qianshan Industrial Park, Xiangzhou District, Zhuhai City, Guangdong Province, China. Phone: 0756-3893087 Fax: 0756-3893230 E-Mail: [email protected] Mode List XP-P501A,XP-P502A,XP-P503A,XP-P504A,XP-P505A,XP-P506A,XP-P507A,XP-P508A, XP-P509A,XP-P510A,XP-P511A,XP-P512A,XP-P513A,XP-P514A,XP-P515A,XP-P516A, XP-P517A,XP-P518A,XP-P519A,XP-P520A,XP-P521A,XP-P522A,XP-P523A,XP-P524A, XP-P525A,XP-P526A,XP-P527A,XP-P528A,XP-P529A,XP-P530A,XP-P501G, XP-P502G, XP-P503G,XP-P504G,XP-P505G,XP-P506G,XP-P507G,XP-P508G,XP-P509G,XP-P510G, XP-P 5 11 G, X P-P512G,XP-P513G,XP-P514G,XP-P515G,XP-P516G, X P-P517G,XP-P518G, XP-P519G,XP-P520G,XP-P521G,XP-P522G,XP-P523G,XP-P524G,XP-P525G,XP-P526G, XP-P527G,XP-P528G,XP-P529G,XP-P530G,XP-P201A,XP-P202A,XP-P203A,XP-P204A, XP-P205A,XP-P206A,XP-P207A,XP-P208A,XP-P209A,XP-P210A,XP-P211A,XP-P212A, XP-P213A,XP-P214A,XP-P215A,XP-P216A,XP-P217A,XP-P218A,XP-P219A,XP-P220A, XP-P221A,XP-P222A,XP-P223A,XP-P224A,XP-P225A,XP-P226A,XP-P227A,XP-P228A, XP-P229A,XP-P230A,XP-P201G,XP-P202G,XP-P203G,XP-P204G,XP-P205G,XP-P206G, XP-P207G,XP-P208G,XP-P209G,XP-P210G,XP-P211G,XP-P212G,XP-P213G,XP-P214G, XP-P215G,XP-P216G,XP-P217G,XP-P218G,XP-P219G,XP-P220G,XP-P221G,XP-P222G, XP-P223G,XP-P224G,XP-P225G,XP-P226G,XP-P227G,XP-P228G,XP-P229G,XP-P230G, XP-P801A,XP-P802A,XP-P803A,XP-P804A,XP-P805A,XP-P806A,XP-P807A,XP-P808A, XP-P809A,XP-P810A,XP-P811A,XP-P812A,XP-P813A,XP-P814A,XP-P815A,XP-P816A, XP-P817A,XP-P818A,XP-P819A,XP-P820A,XP-P821A,XP-P822A,XP-P823A,XP-P824A, XP-P825A,XP-P826A,XP-P827A,XP-P828A,XP-P829A,XP-P830A,XP-P301A,XP-P302A, XP-P303A,XP-P304A,XP-P305A,XP-P306A,XP-P307A,XP-P308A,XP-P309A,XP-P310A, XP-P311A,XP-P312A,XP-P313A,XP-P314A,XP-P315A,XP-P316A,XP-P317A,XP-P318A, XP-P319A,XP-P320A,XP-P321A,XP-P322A,XP-P323A,XP-P324A,XP-P325A,XP-P326A, XP-P327A,XP-P328A,XP-P329A,XP-P330A,XP-P301G,XP-P302G,XP-P303G,XP-P304G, XP-P305G,XP-P306G,XP-P307G,XP-P308G,XP-P309G,XP-P310G,XP-P 3 11 G, X P-P312G, XP-P313G,XP-P314G,XP-P315G,XP-P316G,XP-P317G,XP-P318G,XP-P319G,XP-P320G, XP-P321G,XP-P322G,XP-P323G,XP-P324G,XP-P325G,XP-P326G,XP-P327G,XP-P328G, XP-P329G,XP-P330G,P501A,P502A,P201A,P202A,P201G,P202G,P801A,P802A,P301A, P302A,P301G,P302G,XP-P100,XP-P101,XP-P102,XP-P200,XP-P300,XP-P500,XP-P800, XP-P801,XP-P802,XP-P803,XP-P805,XP-P806,XP-P807,XP-P808,XP-P809,XP-P810, XP-P811,XP-P812,XP-P813,XP-P815,XP-P210,XP-P211,XP-P212,XP-P213,XP-P215, XP-P816,XP-P817,XP-P818,XP-P821,XP-P822,P211,P212,P213,P816,P817,P818

FCC ID: 2AWYKXP-P501A FCC ID: 2AWYKXP-P501A FCC ID: 2AWYKXP-P501A FCC ID: 2AWYKXP-P501A FCC ID: 2AWYKXP-P501A

FCC ID LOCATION

FCC ID LOCATION

FCC ID: 2AWYKXP-P501A FCC ID: 2AWYKXP-P501A BT ANT FCC ID: 2AWYKXP-P501A

RF Exposure evaluation FCC ID: 2AWYKXP-P501A 1.1. Applicable Standard According to §1.1307(b)(1), systems operating under the provisions of this section shall be operated in a manner that ensures that the public is not exposed to radio frequency energy level in excess of the Commission’s guidelines. According to §1.1310 and §2.1093 RF exposure is calculated. KDB447498 v06: Mobile and Portable Devices RF Exposure Procedures and Equipment Authorization Policies. 1.2. Requirement According to KDB447498 D01 General RF Exposure Guidance v06 Section 4.3.1 Standalone SAR test exclusion considerations: “Unless specifically required by the published RF exposure KDB procedures, standalone 1-g head or body and 10-g extremity SAR evaluation for general population exposure conditions, by measurement or numerical simulation, is not required when the corresponding SAR Test Exclusion Threshold condition, listed below, is satisfied. These test exclusion conditions are based on source-based time-averaged maximum conducted output power of the RF channel requiring evaluation, adjusted for tune-up tolerance, and the minimum test separation distance required for the exposure conditions.22 The minimum test separation distance is determined by the smallest distance from the antenna and radiating structures or outer surface of the device, according to the host form factor, exposure conditions and platform requirements, to any part of the body or extremity of a user or bystander (see 5) of section 4.1). To qualify for SAR test exclusion, the test separation distances applied must be fully explained and justified by the operating configurations and exposure conditions of the transmitter and applicable host platform requirements, typically in the SAR measurement or SAR analysis report, according to the required published RF exposure KDB procedures. When no other RF exposure testing or reporting is required, a statement of justification and compliance must be included in the equipment approval, in lieu of the SAR report, to qualify for the SAR test exclusion. When required, the device specific conditions described in the other published RF exposure KDB procedures must be satisfied before applying these SAR test exclusion provisions; for example, handheld PTT two-way radios, handsets, laptops & tablets etc.23 “ [(max. power of channel, including tune-up tolerance, mW)/ (min. test separation distance, mm)] · [√f (GHz)] ≤ 3.0 for 1-g SAR and ≤ 7.5 for 10-g extremity SAR, where: • f (GHz) is the RF channel transmit frequency in GHz • Power and distance are rounded to the nearest mW and mm before calculation • The result is rounded to one decimal place for comparison • 3.0 and 7.5 are referred to as the numeric thresholds in the step 2 below The test exclusions are applicable only when the minimum test separation distance is ≤ 50 mm and for transmission frequencies between 100 MHz and 6 GHz. When the minimum test separation distance is < 5 mm, a distance of 5 mm according to 5) in section 4.1 is applied to determine SAR test exclusion. 1.3. Manufacturing tolerance 2.1. Evaluation Result Band/ Mode f (GHz) Antenna Distance (mm) RF output power (including tune-up tolerance) SAR Test Exclusion Threshold SAR Test Exclusion dBm mW BT 2.402 5 4 2.512 0.779<3.0 Yes Note: Result=P F /D P=Maximum turn-up power in mW F=Channel frequency in GHz D=Mininmun test separation distance in mm 3.1. Conclusion The measurement results comply with the FCC Limit per 47 CFR 2.1093 for the uncontrolled RF Exposure and SAR Exclusion Threshold per KDB 447498 v06, No SAR is required. GFSK Channel Channel 00 Channel 19 Channel 39 Target (dBm) 3.0 3.0 3.0 Tolerance ±(dB) 1.0 1.0 1.0

Page1of34ReportNo.:UNIA20072203ER-01 FCCRADIOTESTREPORT FCCID:2AWYKXP-P501A Product： Portablethermalreceiptprinter Portablethermallabelprinter TradeName： xprinter ModelName： XP-P501A SerialModel： Seemodellistonpage7ofthereport. ReportNo.： UNIA20072203ER-01 Preparedfor ZhuhaiXprinterElectronicsTechnologyCo.,Ltd. 5F,1 st Building,613HuaweiRoad,QianshanIndustrialPark, XiangzhouDistrict,ZhuhaiCity,GuangdongProvince,China. Preparedby ShenzhenUnitedTestingTechnologyCo.,Ltd. 2F,AnnexBldg,JiahuangyuanTechPark,#365Baotian1Rd,Tiegang Community,XixiangStr,Bao'anDistrict,Shenzhen,China Page2of34ReportNo.:UNIA20072203ER-01 TESTRESULTCERTIFICATION Applicant’sname .................... : ZhuhaiXprinterElectronicsTechnologyCo.,Ltd. Address......................................: 5F,1 st Building,613HuaweiRoad,QianshanIndustrialPark, XiangzhouDistrict,ZhuhaiCity,GuangdongProvince,China. Manufacture'sName..............: ZhuhaiXprinterElectronicsTechnologyCo.,Ltd. Address......................................: 5F,1 st Building,613HuaweiRoad,QianshanIndustrialPark, XiangzhouDistrict,ZhuhaiCity,GuangdongProvince,China. Productdescription Productname...............................: Portablethermalreceiptprinter Portablethermallabelprinter TradeMark.................................: xprinter Modeland/ortypereference . : XP-P501A(Seemodellistonpage7ofthereport.) Standards..................................: FCCRulesandRegulationsPart15SubpartCSection15.247, ANSIC63.10:2013 ThisdevicedescribedabovehasbeentestedbyShenzhenUnitedTestingTechnology Co.,Ltd.,andthetestresultsshowthattheequipmentundertest(EUT)isincompliance withtheFCCrequirements.Anditisapplicableonlytothetestedsampleidentifiedinthe report. Thisreportshallnotbereproducedexceptinfull,withoutthewrittenapprovalofUNI,this documentmaybealteredorrevisedbyShenzhenUnitedTestingTechnologyCo.,Ltd., personnelonly,andshallbenotedintherevisionofthedocument. DateofTest ............................................... : Date(s)ofperformanceoftests ............... :July15~27,2020 DateofIssue..............................................:July27,2020 TestResult..................................................:Pass Testedby: Bobliao/Engineer Reviewer: Kahnyang/Supervisor Approved&AuthorizedSigner: Liuze/Manager Page3of34ReportNo.:UNIA20072203ER-01 TableofContentsPage 1.TESTSUMMARY...................................................................................................................5 1.1TESTPROCEDURESANDRESULTS .................................................................................. 5 1.2TESTFACILITY .......................................................................................................................... 5 1.3MEASUREMENTUNCERTAINTY .......................................................................................... 5 2.GENERALINFORMATION...................................................................................................6 2.1GENERALDESCRIPTIONOFEUT.......................................................................................6 2.2CarrierFrequencyofChannels...............................................................................................8 2.3OperationofEUTduringtesting..............................................................................................8 2.4DESCRIPTIONOFTESTSETUP...........................................................................................8 2.5MEASUREMENTINSTRUMENTSLIST................................................................................9 3.CONDUCTEDEMISSIONSTEST ..................................................................................... 10 3.1ConductedPowerLineEmissionLimit...................................................................................10 3.2TestSetup...................................................................................................................................10 3.3TestProcedure...........................................................................................................................10 3.4TestResult..................................................................................................................................10 4.RADIATEDEMISSIONTEST.............................................................................................13 4.1RadiationLimit ........................................................................................................................... 13 4.2TestSetup ................................................................................................................................... 13 4.3TestProcedure ........................................................................................................................... 14 4.4TestResult .................................................................................................................................. 14 5.BANDEDGE.........................................................................................................................19 5.1Limits...........................................................................................................................................19 5.2TestProcedure...........................................................................................................................19 5.3TestResult..................................................................................................................................19 6.OCCUPIEDBANDWIDTHMEASUREMENT .................................................................. 20 6.1TestLimit.....................................................................................................................................20 6.2TestProcedure...........................................................................................................................20 6.3MeasurementEquipmentUsed...............................................................................................2…

Text truncated - open the document above for the full version.

FCC ID: 2AWYKXP-P501A Radiated Emission (Below 1G) Radiated Emission (Above 1G) FCC ID: 2AWYKXP-P501A Conducted Emission