2AX76-CM4Radio receiver for lighting control

X-DRIVER TW Ref. 3481000_r5 MANUALE DI INSTALLAZIONE E USO INSTALLATION MANUAL INSTALLATIONSHANDBUCH MANUEL D'INSTALLATION MANUAL DE INSTALACIÓN IT EN DE FR ES DOMUS Line Srl Via Maestri del Lavoro, 1 33080 PORCIA _ PN _ Italy phone fax e-mail website 0039 0434 595911 0039 0434 923345 [email protected] www.domusline.com 110 Device in insulation class II. Connection to the earthing circuit is not necessary. Gerät der isolierklasse II. Der Anschluss an einen geerdeten Kreislauf ist hier nicht notwending. Luminaire de classe II (isolation). Raccordement au circuit de mise à la terre non indispensable. Aparato en clase de aislamiento II. No es necesaria la conesion al circuito de tierra. Apparecchio in classe d'isolamento II. Non è necessaria la connessione al circuito di messa a terra. Independent transformer specially designed to be installed ”visible” (it can be used without the supplementary protective case and without being integrated into lights). LED-Transformator für selbstständigen Einsatz bei “sichtbaren” Installationen (auch ohne zusätzliche Schutzhülle und ohne Einbau in Beleuchtungen einsetzbar). Transformateur indépendant spécifique pour installations “a vue” (pet être utilisé sans bâche de protection supplémentaire et sans être incorporé dans des appareils d'éclairage). Transformador independiente, específico para instalaciones a la vista (se puede utilizar sin carcasa adicional de protección y sin incorporarlo a aparatos de iluminación). Trasformatore per uso indipendente specifico per installazioni “a vista” (può essere utilizzato senza involucro supplementare di protezione e senza essere incorporato in apparecchi di illuminazione). Lamp power supply unit thermally protected at 110°C Thermisch geschützten Lampe Netzgeräte bis 110°C Alimentation de la lampe protégée thermiquement à 110°C. Unidades de potencia de la lámpara de protección térmica a 110°C Unità di alimentazione lampada protetta termicamente a 110°C. SELV EQUIVALENT This symbol indicates that the transformer complies with the European EN 61347-1 standard. The SELV symbol (Safety Extra Low Voltage) identifies a transformer in which touching the secondary circuit outputs, even if no lamps are connected, does not constitute a hazard. Dieses Symbol zeigt an, dass der Transformator mit der Europäischen EN 61347-1 Standard entspricht. Das SELV-Symbol (Safety Extra Low Voltage) identifiziert einen Transformator, bei dem Berühren der Sekundärkreis-Ausgänge auch wenn keine Leuchten angeschlossen sind, keine Gefahr darstellen. Il indique que le transformateur est conforme au normatif Européen EN 613147-1. Le symbole SELV (Safety Extra Low Voltage - Basse tension de sûreté) identifie un appareil en qui, aussi en service au vide (c'est-à-dire sans lampes reliè), il est possible de toucher la sortie du secondaire sans quelques-uns danger. Indica que el transformador está conforme a la normativa europeo EN 613147-1. El símbolo SELV (Safety Extra Low Voltage - Baja tensión de seguridad), identifica un aparato en el que, también en servicio a vacío (es decir sin lámparas unidas), es posible tocar la salida de lo secundario sin ningún peligro Indica che il trasformatore è conforme alla normativa Europea EN 613147-1. Il simbolo SELV (Safety Extra Low Voltage - Bassissima tensione di sicurezza) identifica un apparecchio nel quale, anche in servizio a vuoto (cioè senza lampade collegate), è possibile toccare l'uscita del secondario senza alcun pericolo. The product must be disposed of separately from urban waste, delivering it to the collection centres established by the prevailing standard. Adequate sorted waste collection contributes to preventing negative effects on the environment and health and favours reuse and/or recycling materials. Incorrect disposal of the product implies the application of the administrative sanctions envisaged by the prevailing regulation. Die Leuchte muss getrennt vom Hausmüll entsorgt und entsprechend der geltenden Richtlinien, an den vorgesehenen Sammelstellen abgegeben werden. Die angemessene getrennte Sammlung trägt dazu bei, eventuelle negative Auswirkungen auf die Umwelt und die Gesundheit zu vermeiden und die Wiederverwendung und/oder das Recycling der Materialien zu begünstigen. Die unsachgemäße Entsorgung bringt die Anwendung administrativer Strafen mit sich, die in den geltenden Richtlinien vorgesehen sind. Le produit doit être collecté séparément et non jeté avec les déchets ménagers en le portant dans les déchetteries prévues par la réglementation en vigueur. Un tri sélectif approprié contribue à éviter des possibles effets négatifs sur l'environnement et sur la santé et favorise la réutilisation et/ou le recyclage des matériaux. L'élimination abusive entraîne l'application des sanctions administratives prévues par la réglementation en vigueur. Se debe desechar el producto de forma separada de los residuos urbanos; se lo debe entregar en los centros de recolección previstos por la norma en vigor. La recolección diferenciada adecuada contribuye a evitar posibles efectos negativos en el medioambiente y en la salud y favorece la reutilización y/o el reciclaje de los materiales. Si se lo desecha en forma abusiva tendrá como consecuencia la aplicación de sanciones administrativas previstas por la normativa vigente. Il prodotto deve essere smaltito separatamente dai rifiuti urbani consegnandolo ai centri di raccolta previsti dalla normativa in vigore. L'adeguata raccolta differenziata contribuisce ad evitare possibili effetti negativi sull'ambiente e sulla salute e favorisce il reimpiego e/o il riciclo dei materiali. Lo smaltimento abusivo comporta l'applicazione delle sanzioni amministrative previste dalla normativa vigente. Specifications Input frequency Input current Output voltage Rated output power Dimming range Operation mode Ambient temperature X-DRIVER TW 15Watt X-DRIVER TW 30Watt X-DRIVER TW 60Watt Input voltage 100-120VAC,220-240Vac (100-120VAC for North America only) 50/60Hz IP20 0-15W…

Text truncated - open the document above for the full version.

DOMUS LINE SRL Date: 2020-12-05 To: Federal Communications Commission 7435 Oakland Mills Road Columbia, MD FCC ID: 2AX76-CM4 To Whom It May Concern: This letter is to ascertain that DOMUS LINE SRL EUT : Radio receiver for lighting control Model Name : CM4-XD, CM4-XDTW, CM4-XDM We will apply for FCC SDOC. If you have any question or concerns, pls. contact us. Sincerely, Client’s signature ： Client’s name / title ： Alberto Zannese/Compliance Manager Contact information / address: DOMUS LINE SRL /VIA MAESTRI DEL LAVORO 1, 33080 Porcia (Pn) Italy

(DOMUS LINE SRL) Federal Communications Commission Authorization and Evaluation Division Confidentiality Request regarding application for certification of FCC ID: 2AX76-CM4 Pursuant to Sections 0.457 and 0.459 of the Commission’s Rules, we hereby request confidential treatment of information accompanying this application as outlined below: Exhibit Type File Name BOM, Block Diagram, Schematics, Operational Description Block Diagram .pdf, Schematics .pdf , Operation Description .pdf, BOM.pdf The above materials contain trade secrets and proprietary information not customarily released to the public. The public disclosure of these materials may be harmful to the applicant and provide unjustified benefits to its competitors. The applicant understands that pursuant to Section 0.457 of the Rules, disclosure of this application and all accompanying documentation will not be made before the date of the Grant for this application. Pursuant to DA04-1705 June 15, 2004 of the Commission’s public notice, we also request temporary confidential treatment of information accompanying this application as outlined below: Short-term confidentiality requested: 180 days Exhibit Type File Name Internal Photos, Test Setup Photos, Manual Internal Photos .pdf, Test Setup Photos .pdf, User Manual .pdf Sincerely, Name: Alberto Zannese Title: Compliance Manager Company: DOMUS LINE SRL

Difference Statement Models CM4-XD, CM4-XDTW, CM4-XDM All models are the same except the programs and software. Model CM4-XD can adjust the brightness. Model CM4-XDTW can adjust the brightness and control the 3-line color temperature. Model CM4-XDM can adjust the brightness and control the 2-line color temperature. December 05, 2020 Name: Alberto Zannese Title: Compliance Manager Company: DOMUS LINE SRL

(DOMUS LINE SRL) Federal Communications Commission Authorization and Evaluation Division 1435 Oakland Mills Road Columbia, MD 21046 Date: December 05, 2020 SUBJECT: FCC Application for FCC ID: 2AX76-CM4 To Whom It May Concern: We, the undersigned, hereby authorize Tony Wei at EMTEK(NINGBO) CO., LTD. on our behalf, to apply to the Federal Communications Commission on our equipment. Any and all acts carried out by EMTEK(NINGBO) CO., LTD. on our behalf shall have the same effect as acts of our own. This is to advise that we are in full compliance with the Anti- Drug Abuse Act. We, the applicant, are not subject to a denial of federal benefits pursuant to Section 5301 of the Anti-Drug Act of 1988, 21 USC853a, and no party to the application is subject to a denial of federal benefits pursuant to that section. Regards, Name: Alberto Zannese Title: Compliance Manager Company: DOMUS LINE SRL

External photos: ---The End---

Label and Location_1 Label and Location_2 Label and Location_3

Internal photos: Antenna ---The End---

FCC ID: 2AX76-CM4 RF EXPOSURE EVALUATION According to FCC 1.1310: The criteria listed in the following table shall be used to evaluate the environment impact of human exposure to radio frequency(RF) Radiation as specified in §1.1307(b) Limits for Maximum Permissible Exposure (MPE) Frequency Range(MHz) Electric Field Strength(V/m) Magnetic Field Strength(A/m) Power Density(mW/cm 2 ) Average Time (A) Limits for Occupational/Control Exposures 300-1500 -- -- F/300 6 1500-100000 -- -- 5 6 (B) Limits for General Population/Uncontrol Exposures 300-1500 -- -- F/1500 6 1500-100000 -- -- 1 30 11.1 Friis transmission formula: Pd= (Pout*G)\ (4*pi*R 2 ) Where Pd= Power density in mW/cm 2 Pout=output power to antenna in mW G= Numeric gain of the antenna relative to isotropic antenna Pi=3.1416 R= distance between observation point and center of the radiator in cm Pd the limit of MPE,1mW/cm 2 . If we know the maximum gain of the antenna and total power input to the antenna, through the calculation, we will know the distance where the MPE limit is reached. mW = 10^( dBm/10) 11.2 Measurement Result Operation Frequency: 2412MHz-2462MHz; Antenna gain: 0 dBi; R=20cm WIFI Channel Freq. (MHz) modulation Measured power (dBm) Tune-up power (dBm) Max tune-up power (dBm) Antenna Gain Numeric Evaluation result (mW/cm2) Power density Limits (mW/cm2 ) 2412 802.11b 14.99 13 to15 15 1.0 0.006291137 1 2437 15.45 14 to16 16 1.0 0.007920072 1 2462 15.54 14 to16 16 1.0 0.007920072 1 2412 802.11g 14.15 13 to15 15 1.0 0.006291137 1 2437 14.54 13 to15 15 1.0 0.006291137 1 2462 15.07 14 to16 16 1.0 0.007920072 1 2412 802.11n20 13.89 12 to14 14 1.0 0.004997228 1 2437 14.39 13 to15 15 1.0 0.006291137 1 2462 14.78 13 to15 15 1.0 0.006291137 1 *** End of Report ***

Report No.ES200831103W Page 1 of 48 Ver.1.0 TEST REPORT $二维码$ Product Name : Radio receiver for lighting control Model Number : CM4-XD, CM4-XDTW, CM4-XDM FCC ID : 2AX76-CM4 Prepared for : DOMUS LINE SRL Address : VIA MAESTRI DEL LAVORO 1, 33080 Porcia (Pn) Italy Prepared by : EMTEK (SHENZHEN) CO., LTD. Address : Building69, Majialong Industry Zone, Nanshan District, Shenzhen, Guangdong, China Tel: (0755) 26954280 Fax: (0755) 26954282 Report Number : ES200831103W Date(s) of Tests : August 31, 2020 to December 22, 2020 Date of Issue : December 23, 2020 Report No.ES200831103W Page 2 of 48 Ver.1.0 TABLE OF CONTENTS 1 TEST RESULT CERTIFICATION ............................................................................................................. 3 2 EUT TECHNICAL DESCRIPTION ........................................................................................................... 4 3 SUMMARY OF TEST RESULT ................................................................................................................ 5 4 TEST METHODOLOGY ........................................................................................................................... 6 4.1 GENERAL DESCRIPTION OF APPLIED STANDARDS .................................................................. 6 4.2 MEASUREMENT EQUIPMENT USED ............................................................................................ 6 4.3 DESCRIPTION OF TEST MODES ................................................................................................... 7 4.4 TEST SOFTWARE ........................................................................................................................... 8 5 FACILITIES AND ACCREDITATIONS ..................................................................................................... 9 5.1 FACILITIES ...................................................................................................................................... 9 5.2 LABORATORY ACCREDITATIONS AND LISTINGS ....................................................................... 9 6 TEST SYSTEM UNCERTAINTY ............................................................................................................ 10 7 SETUP OF EQUIPMENT UNDER TEST ............................................................................................... 11 7.1 RADIO FREQUENCY TEST SETUP 1 ............................................................................................ 11 7.2 RADIO FREQUENCY TEST SETUP 2 ............................................................................................ 11 7.3 CONDUCTED EMISSION TEST SETUP ....................................................................................... 12 7.4 BLOCK DIAGRAM CONFIGURATION OF TEST SYSTEM ........................................................... 13 7.5 SUPPORT EQUIPMENT ................................................................................................................ 13 8 TEST REQUIREMENTS ......................................................................................................................... 14 8.1 DTS (6DB) BANDWIDTH ............................................................................................................... 14 8.2 MAXIMUM PEAK CONDUCTED OUTPUT POWER ..................................................................... 20 8.3 MAXIMUM POWER SPECTRAL DENSITY ................................................................................... 21 8.4 UNWANTED EMISSIONS IN NON-RESTRICTED FREQUENCY BANDS ................................... 27 8.5 RADIATED SPURIOUS EMISSION ............................................................................................... 32 8.6 CONDUCTED EMISSIONS TEST ................................................................................................. 44 8.7 ANTENNA APPLICATION .............................................................................................................. 47 Report No.ES200831103W Page 3 of 48 Ver.1.0 1 TEST RESULT CERTIFICATION Applicant : DOMUS LINE SRL Address : VIA MAESTRI DEL LAVORO 1, 33080 Porcia (Pn) Italy Manufacturer : SELF ELECTRONICS CO., LTD Address : No.1345, JuXian Road, Hi-tech Park, Ningbo, China EUT : Radio receiver for lighting control Model Name : CM4-XD, CM4-XDTW, CM4-XDM Trademark : DOMUS LINE Measurement Procedure Used: APPLICABLE STANDARDS STANDARD TEST RESULT FCC 47 CFR Part 2, Subpart J FCC 47 CFR Part 15, Subpart C PASS The above equipment was tested by EMTEK (SHENZHEN) CO., LTD. The test data, data evaluation, test procedures, and equipment configurations shown in this report were made in accordance with the procedures given in ANSI C63.10 (2013) and the energy emitted by the sample EUT tested as described in this report is in compliance with the requirements of FCC Rules Part 2 and Part 15.247 The test results of this report relate only to the tested sample identified in this report. Date of Test : August 31, 2020 to December 22, 2020 Prepared by : SewenGuo /Editor Reviewer : Sevin Li/Supervisor Approve & Authorized Signer : Lisa Wang/Manager Report No.ES200831103W Page 4 of 48 Ver.1.0 2 EUT TECHNICAL DESCRIPTION Note: for more details, please refer to the User’s manual of the EUT. Characteristics Description Product Radio receiver for lighting control Model Number CM4-XD, CM4-XDTW, CM4-XDM (Note: All models are the same except the programs and software. Model CM4-XD can adjust the brightness. Model CM4-XDTW can adjust the brightness and control the 3-line color temperature. Model CM4-XDM can adjust the brightness and control the 2-line color temperature. We prepared model CM4-XDTW for EMC test.) IEEE 802.11 WLAN Mode Supported 802.11b 802.11g 802.11n(20MHz channel bandwidth) 802.11n(40MHz channel bandwidth) Data Rate 802.11 b:1,2,5.5,11Mbps; 802.11 g:6,9,12,18,24,36,48,54Mbps; 802.11n(HT20): MCS0~7,up to65Mbps Modulation DSSS with DBPSK/DQPSK/CCK for 802.11b; OFDM with BPSK/…

Text truncated - open the document above for the full version.

Conducted Radiated ---The End---