2AXAVSI4002405Smart inspection camera

Wöhler SI 400 Ausführliche Anleitung woehler.de/P_200.dl Complete Manual woehler- international.com/P_200 .dl Mode d’emploi détaillé woehler.fr/P_200.dl EN FR DE Bestell-Nr. 25441 2024-05-29 volledige instructies woehler.nl/P_200.dl Istruzioni complete woehler.it/P_200.dl NL IT DE Kurzanleitung 1 Akku aufladen 2 Speicherkarte einlegen 3 Einschalten Kameraoberteil auf Unterteil schrauben Kamera auf Stange schrauben 1 2 3 4 Wöhler SI 400 Unterteil Startbildschirm Smart Inspection App DE Smart Inspection App auf mobilem Endgerät öffnen 4 Mobiles Endgerät mit Wöhler SI 400 verbinden Inspizieren EN Operating manual 1 Charge battery 2 Insert memory card 3 Switch on Screw the upper part of the camera onto the lower part Screw camera onto bar Open Smart Inspection app on mobile device 4 Connect mobile device to Wöhler SI 400 Inspect 1 2 3 4 Wöhler SI 400 lower part (unscrewed) Start screen Smart Inspection App FR Mode d'emploi 1 Recharger la batterie 2 Insérer la carte mémoire 3 Allumer / éteindre Visser la partie supérieure de la caméra sur la partie inférieure Visser la caméra sur la tige Ouvrir l'application « Smart Inspection » sur le smartphone 4 Connecter smartphone au Wöhler SI 400 Inspecter 1 2 3 4 Wöhler SI 400 Partie inférieure (dévissée) Écran d'accueil Smart Inspection App NL Gebruiksaanwijzing 1 Batterij opladen 2 Geheugenkaart plaatsen 3 Aanzetten Schroef het bovenste deel van de camera op het onderste deel Camera op paal schroeven Open de Smart Inspection app op het mobiele apparaat 4 Een mobiel apparaat aansluiten op de Wöhler SI 400 Inspecteer 1 2 3 4 Wöhler SI 400 onderste deel (losgeschroefd) Startscherm Smart Inspection App IT Istruzioni per l'uso 1 Carica della batteria 2 Inserire la scheda di memoria 3 Accendere Avvitare la parte superiore della telecamera su quella inferiore Avvitare la telecamera sull'asta Aprire l'applicazione Smart Inspection sullo smartphone 4 Collegare lo smartphone con il Wöhler SI 400 Ispezionare 1 2 3 4 Wöhler SI 400 parte inferiore (svitata) Schermo iniziale Smart Inspection App Wöhler Technik GmbH Wöhler-Platz 1 33181 Bad Wünnenberg Tel.: +49 2953 73-100 E- Mail: [email protected] IT FCC Caution: Any Changes or modifications not expressly approved by the party responsible for compliance could void the user's authority to operate the equipment. This device complies with part 15 of the FCC Rules. Operation is subject to the following two conditions: (1) This device may not cause harmful interference, and (2) this device must accept any interference received, including interference that may cause undesired operation. IMPORTANT NOTE: Note: This equipment has been tested and found to comply with the limits for a Class B digital device, pursuant to part 15 of the FCC Rules. These limits are designed to provide reasonable protection against harmful interference in a residential installation. This equipment generates, uses and can radiate radio frequency energy and, if not installed and used in accordance with the IT instructions, may cause harmful interference to radio communications. However, there is no guarantee that interference will not occur in a particular installation. If this equipment does cause harmful interference to radio or television reception, which can be determined by turning the equipment off and on, the user is encouraged to try to correct the interference by one or more of the following measures: —Reorient or relocate the receiving antenna. —Increase the separation between the equipment and receiver. —Connect the equipment into an outlet on a circuit different from that to which the receiver is connected. —Consult the dealer or an experienced radio/TV technician for help. FCC Radiation Exposure Statement: This equipment complies with FCC radiation exposure limits set forth for an uncontrolled environment.

CFR 47 §2.911(d)(5)(i) Attestation Letter Shenzhen Teslong Technology Co., Ltd. 2nd Floor, Block 4, Jinhuafa Industrial Park, East of Donghuan 2 avenue, Longhua, Shenzhen, China Tel: +86-18566655696 Email: [email protected] Attestation Letter Date: 2024-06-03 FEDERAL COMMUNICATIONS COMMISSIONS Authorization and Evaluation Division 7435 Oakland Mills Road Columbia, MD 21046 Ref: Attestation Statements CFR 47 §2.911(d)(5)(i) Filing F CC ID: 2AXAVSI4002405 Shenzhen Teslong Technology Co., Ltd. certifies that the equipment for which authorization is sought, is not “covered” equipment prohibited from receiving an equipment authorization pursuant to section 2.903 of the FCC rules. Sincerely, Signature R ichard Ren /Manger

CFR 47 §2.911 (d)(5)(ii) Attestation Letter Shenzhen Teslong Technology Co., Ltd. 2nd Floor, Block 4, Jinhuafa Industrial Park, East of Donghuan 2 avenue, Longhua, Shenzhen, China Tel: +86-18566655696 Email: [email protected] Attestation Letter Date: 2024-06-03 FEDERAL COMMUNICATIONS COMMISSIONS Authorization and Evaluation Division 7435 Oakland Mills Road Columbia, MD 21046 Ref: Attestation Statements CFR 47 §2.911(d)(5)(ii) Filing F CC ID: 2AXAVSI4002405 Shenzhen Teslong Technology Co., Ltd. certifies that as of the date of the filing of the application, the applicant is not identified on the Covered List as an entity producing “covered” equipment. Sincerely, Signature R ichard Ren /Manger

U.S. AGENT LETTER OF ATTESTATION Date: 2024-06-03 FEDERAL COMMUNICATIONS COMMISSION Authorization and Evaluation Division 7435 Oakland Mills Road Columbia, MD 21046 Ref: Attestation Statements CFR 47 §2.911(d)(7) Filing FCC ID: 2AXAVSI4002405 She nzhen Teslong Technology Co., Ltd. certifies that, as of the date of the filing of the application, ScopeAround Inc. is our designated U.S. agent for service of process for the above referenced FCC ID. Shenzhen Teslong Technology Co., Ltd. accepts to maintain an agent for no less than one year after the grantee has terminated all marketing and importation or the conclusion of any Commission-related proceeding involving the equipment. ScopeAround Inc. accepts, as of the date of the filing of the application, the obligation of the designated U.S. agent for service of process for the above referenced FCC ID. D esignated U.S. Agent Information: Name: ScopeAround Inc. Address: 17795 SKY PARK CIR STE G IRVINE CA 92614-6133 California, CA 92614-6133 United States FRN: 0033415290 Tel.: (949) 877-7999 Email: [email protected] Signed by (printed name): George Wang Signature: Applicant: Shenzhen Teslong Technology Co., Ltd. Address: 2nd Floor, Block 4, Jinhuafa Industrial Park, East of Donghuan 2 avenue, Longhua, Shenzhen, China FRN: 0029882032 Tel.: +86-18566655696 Email: [email protected] Signed by (printed name): Richard Ren Signature:

Shenzhen Teslong Technology Co., Ltd. 2nd Floor, Block 4, Jinhuafa Industrial Park, East of Donghuan 2 avenue, Longhua, Shenzhen, China Tel: +86-18566655696 Email: [email protected] QA-FR-170-B 7/29/2014 FCC Authorization Date: 2024-06-03 FEDERAL COMMUNICATIONS COMMISSIONS Authorization and Evaluation Division 7435 Oakland Mills Road Columbia, MD 21046 Subject: Agent Authorization To whom it may concern: We Shenzhen Teslong Technology Co., Ltd., the undersigned, hereby authorizes World Alliance Testing and Certification (Shenzhen) Co., Ltd to act on its behalf in all matters relating to application for Equipment authorization, including the signing of all documents relating to these matters. All acts carried out by World Alliance Testing and Certification (Shenzhen) Co., Ltd on our behalf shall have the same effect as our own action. We, the undersigned, hereby certify that we are not subject to a denial of federal benefits, that includes FCC benefits, pursuant to Section 5301 of the Anti-Drug Abuse Act of 1988, 21 U.S.C. 862. T his authorization is valid until further written notice from the applicant. Sincerely, S ignature R ichard Ren Title: Manger

Shenzhen Teslong Technology Co., Ltd. 2nd Floor, Block 4, Jinhuafa Industrial Park, East of Donghuan 2 avenue, Longhua, Shenzhen, China Tel: +86-18566655696 Email: [email protected] FCC Confidential Authorization Date: 2024-06-03 FEDERAL COMMUNICATIONS COMMISSIONS Authorization and Evaluation Division 7435 Oakland Mills Road Columbia, MD 21046 Subject: Confidentiality Request regarding application for certification of FCC ID: 2AXAVSI4002405 In accordance with Sections 0.457 and 0.459 of the Commission’s Rules, Shenzhen Teslong Technology Co., Ltd. hereby requests long-term confidential treatment of information accompanying this application as outlined below: •B lock Diagram •Schematics •Operation Description T he above materials contain proprietary and confidential information not customarily released to the public. The public disclosure of these materials provides unjustified benefits to its competitors in the market. Sincerely, S ignature Name: Richard Ren Title: Manger

Shenzhen Teslong Technology Co., Ltd. 2nd Floor, Block 4, Jinhuafa Industrial Park, East of Donghuan 2 avenue, Longhua, Shenzhen, China Tel: +86-18566655696 Email: [email protected] Date: 2024-06-03 FEDERAL COMMUNICATIONS COMMISSIONS Authorization and Evaluation Division 7435 Oakland Mills Road Columbia, MD 21046 To whom it may concern: Our product Smart inspectio n camera, Model: SI 400; FCC ID: 2AXAVSI4002405. For use in America, this product only support 2.4G Wi-Fi (2412-2472MHz, 802.11b/g/ n-HT20 mode). The other functions, bands and modes has been shielded by the manufacturer using the software, the end user has no capability to activate it. Sin cerely, Signature Na me: Richard Ren Title: Manger

Report No.: 2405T75792E Page 1 of 4 EUT EXTERNAL PHOTOGRAPHS Report No.: 2405T75792E Page 2 of 4 Report No.: 2405T75792E Page 3 of 4 Report No.: 2405T75792E Page 4 of 4

F C C I D : 2 A X A V S I 4 0 0 2 4 0 5 F C C I D : 2 A X A V S I 4 0 0 2 4 0 5 F C C I D : 2 A X A V S I 4 0 0 2 4 0 5 16mm 3.6mm 30mm 16mm

Report No.: 2405T75792E Page 1 of 6 EUT INTERNAL PHOTOGRAPHS Report No.: 2405T75792E Page 2 of 6 Report No.: 2405T75792E Page 3 of 6 ANT Report No.: 2405T75792E Page 4 of 6 Report No.: 2405T75792E Page 5 of 6 Report No.: 2405T75792E Page 6 of 6

Report Template: TR-4-E-016/V1.0 RF Exposure Evaluation Report No.: 2405T75792E Applicant: Shenzhen Teslong Technology Co., Ltd. Address: 2nd Floor, Block 4, Jinhuafa Industrial Park, East of Donghuan 2 avenue, Product Name: Smart inspection camera Product Model: SI 400 Multiple Models: N/A Trade Mark: FCC ID: 2AXAVSI4002405 Standards: 47 CFR §1.13 KDB 447498 D0 Test Date: 2024 Test Result: Complied Report Date: 2024 Reviewed by: Abel Chen Project Engineer World Alliance Testing No. 1002, East Block, Laobing Building, Xingye This report may contain data that are not covered by the NVLAP accreditation and shall be marked with an asterisk “★” Report No.: Page 1 of 5 RF Exposure Evaluation Report 2405T75792EC Shenzhen Teslong Technology Co., Ltd. 2nd Floor, Block 4, Jinhuafa Industrial Park, East of Donghuan 2 avenue, Longhua, Shenzhen, China Smart inspection camera 400 2AXAVSI4002405 47 CFR §1.1310 KDB 447498 D01 General RF Exposure Guidance v06 2024-05-16 Complied 2024-05-30 Approved by: Abel Chen Project Engineer Prepared by: World Alliance Testing & Certification (Shenzhen) Co., Ltd No. 1002, East Block, Laobing Building, Xingye Road 3012, Xixiang street, Bao'an District, Shenzhen, Guangdong, People’s Republic of China This report may contain data that are not covered by the NVLAP accreditation and shall be marked with an Report No.: 2405T75792EC Report 2nd Floor, Block 4, Jinhuafa Industrial Park, East of Donghuan 2 General RF Exposure Guidance v06 Jacob Kong Manager Certification (Shenzhen) Co., Ltd Road 3012, Xixiang street, Bao'an District, Shenzhen, This report may contain data that are not covered by the NVLAP accreditation and shall be marked with an Report Template: TR-4-E-016/V1.0 1. This test report shall not be reproduced except in full, without the written approval of World Alliance Testing & Certification (Shenzhen) Co., Ltd 2. The results in this report apply only to the sample tested. 3. This sample tested is in compliance with the limits of the above regulation. 4. This report must not be used by the client to claim product certification, approval, or endorsement by NVLAP, NIST, or any agency of the 5. The information marked “#” authenticity and this information can affect the validity of the result in the test report. Customer model name, addresses, names, trademarks etc. are included. Version No. 00 Report No.: Page 2 of 5 Announcement This test report shall not be reproduced except in full, without the written approval of World Alliance cation (Shenzhen) Co., Ltd 2. The results in this report apply only to the sample tested. in compliance with the limits of the above regulation. This report must not be used by the client to claim product certification, approval, or endorsement by NVLAP, NIST, or any agency of the U.S. Government. is provided by the applicant, the laboratory is not responsible for its authenticity and this information can affect the validity of the result in the test report. Customer model name, addresses, names, trademarks etc. are included. Revision History Issued Date Description 2024-05-30 Original Report No.: 2405T75792EC This test report shall not be reproduced except in full, without the written approval of World Alliance This report must not be used by the client to claim product certification, approval, or endorsement by is provided by the applicant, the laboratory is not responsible for its authenticity and this information can affect the validity of the result in the test report. Customer model name, Description Original Report Template: TR-4-E-016/V1.0 1 General Information ................................ 1.1 Client Information ................................ 1.2 Product Description of 1.3 Laboratory Location ................................ 2 RF Exposure Evaluation ................................ 2.1 Standard ................................ 2.2 Result................................ Report No.: Page 3 of 5 Contents ................................................................................................ ................................................................................................ of EUT ................................................................................................ ................................................................................................ ................................................................................................ ................................................................................................ ................................................................................................................................ Report No.: 2405T75792EC ............................................................ 4 ...................................................... 4 ....................................... 4 ................................................... 4 ..................................................... 5 .................................................................... 5 ......................................... 5 Report Template: TR-4-E-016/V1.0 1 General Information 1.1 Client Information Applicant: Shenzhen Teslong Technology Co., Ltd. Address: 2nd Floor, Block 4, Jinhuafa Industrial Park, East of Donghuan 2 avenue, Longhua, Manufacturer: Shenzhen Teslong Technology Co., Ltd. Address: 2nd Floor, Block 4, Jinhuafa Industrial Park, East of Donghuan 2 avenue, Longhua, Shenzhen, China 1.2 Product Description The EUT is Smart inspection camera Sample Serial Number 2LA6 Sample Received Date 2024 Sample Status Good Condition Frequency Range 2412MHz Maximum Conducted Output Power 9.16dBm Modulation Technology DSSS, OFDM Antenna Gain # 0.67 Spatial Streams SISO (1TX, 1RX) Power Supply DC 3.7V from battery or DC 5.0V from USB port Operating temperature # 0 deg.C to +45 deg.C Adapter Information N/A Modification Sample 1.3 Laboratory Location World Alliance Testing & Certification (Shenzhen) Co., Ltd No. 1002, East Block, Laobing Buil…

Text truncated - open the document above for the full version.

Report No.: 2405T75792EB Report Template: TR-4-E-009/V1.0 Page 1 of 34 FCC Test Report Report No.: 2405T75792EB Applicant: Shenzhen Teslong Technology Co., Ltd. Address: 2nd Floor, Block 4, Jinhuafa Industrial Park, East of Donghuan 2 avenue, Longhua, Shenzhen, China Product Name: Smart inspection camera Product Model: SI 400 Multiple Models: N/A Trade Mark: FCC ID: 2AXAVSI4002405 Standards: FCC CFR Title 47 Part 15C (§15.247) Test Date: 2024-05-14 to 2024-05-16 Test Result: Complied Report Date: 2024-05-30 Reviewed by: Approved by: Abel Chen Project Engineer Jacob Kong Manager Prepared by: World Alliance Testing & Certification (Shenzhen) Co., Ltd No. 1002, East Block, Laobing Building, Xingye Road 3012, Xixiang street, Bao'an District, Shenzhen, Guangdong, People’s Republic of China This report may contain data that are not covered by the NVLAP accreditation and shall be marked with an asterisk “★” Report No.: 2405T75792EB Report Template: TR-4-E-009/V1.0 Page 2 of 34 Announcement 1. This test report shall not be reproduced except in full, without the written approval of World Alliance Testing & Certification (Shenzhen) Co., Ltd 2. The results in this report apply only to the sample tested. 3. This sample tested is in compliance with the limits of the above regulation. 4. This report must not be used by the client to claim product certification, approval, or endorsement by NVLAP, NIST, or any agency of the U.S. Government. 5. The information marked “#” is provided by the applicant, the laboratory is not responsible for its authenticity and this information can affect the validity of the result in the test report. Customer model name, addresses, names, trademarks etc. are included. Revision History Version No. Issued Date Description 00 2024-05-30 Original Report No.: 2405T75792EB Report Template: TR-4-E-009/V1.0 Page 3 of 34 Contents 1 General Information ............................................................................................................................ 4 1.1 Client Information ...................................................................................................................... 4 1.2 Product Description of EUT ....................................................................................................... 4 1.3 Antenna information .................................................................................................................. 4 1.4 Related Submittal(s)/Grant(s) .................................................................................................... 5 1.5 Measurement Uncertainty ......................................................................................................... 5 1.6 Laboratory Location ................................................................................................................... 5 1.7 Test Methodology ...................................................................................................................... 5 2 Description of Measurement .............................................................................................................. 6 2.1 Test Configuration ...................................................................................................................... 6 2.2 Test Auxiliary Equipment ........................................................................................................... 6 2.3 Test Setup .................................................................................................................................. 7 2.4 Test Procedure .......................................................................................................................... 9 2.5 Measurement Method.............................................................................................................. 10 2.6 Measurement Equipment ......................................................................................................... 11 3 Test Results ....................................................................................................................................... 12 3.1 Test Summary .......................................................................................................................... 12 3.2 Limit ......................................................................................................................................... 13 3.3 AC Line Conducted Emissions Test Data ................................................................................ 14 3.4 Radiated emission Test Data ................................................................................................... 16 3.5 RF Conducted Test Data ......................................................................................................... 23 3.5.1 6dB Emission Bandwidth and 99% Occupied Bandwidth ............................................ 23 3.5.2 Maximum Conducted Peak Output Power ................................................................... 23 3.5.3 Power Spectral Density ................................................................................................ 24 3.5.4 100 kHz Bandwidth of Frequency Band Edge ............................................................. 24 3.5.5 Duty Cycle .................................................................................................................... 24 4 Test Setup Photo ............................................................................................................................... 33 5 E.U.T Photo ........................................................................................................................................ 34 Report No.: 2405T75792EB Report Template: TR-4-E-009/V1.0 Page 4 of 34 1 General Information 1.1 Client Information Applicant: Shenzhen Teslong Technology Co., Ltd. Address: 2nd Floor, Block 4, Jinhuafa Industrial Park, East of Donghuan 2 avenue, Longhua, Shenzhen, China …

Text truncated - open the document above for the full version.

Report No.: 2405T75792E Page 1 of 2 TEST SETUP PHOTOGRAPHS AC Line Conducted Emission Report No.: 2405T75792E Page 2 of 2 Radiated Emission Below 1GHz Above 1 GHz