2AXCX-2843L1123AUTOMOTIVE DIAGNOSTIC PLATFORM

Trademarks FOXWELL is the trademark of Shenzhen Foxwell Technology Co., Ltd. All other marks are trademarks or registered trademarks of their respective holders. Copyright Information ©2023 Shenzhen Foxwell Technology Co., Ltd. All rights reserved. Disclaimer The information, specifications and illustrations in this manual are based on the latest information available at the time of printing. Foxwell reserves the right to make changes at any time without notice. Visit our website at www.foxwelltech.us For Technical Assistance, send us email at [email protected] 1 NT6 X 4Elite Series User’s Manual_English_ V 1 . 0 3 One-Year Limited Warranty Subject to the conditions of this limited warranty, Shenzhen Foxwell Technology Co., Ltd (“ FOXWELL”) warrants its customer that this product is free of defects in material and workmanship at the time of its original purchase for a subsequent period of one (1) year. In the event this product fails to operate under normal use, during the warranty period, due to defects in materials and workmanship, FOXWELL will, at its sole option, either repair or replace the product in accordance with the terms and conditions stipulated herein. Terms and Conditions 1 If FOXWELL repairs or replaces the product, the repaired or replaced product shall be warranted for the remaining time of the original warranty period. No charge will be made to the customer for replacement parts or labor charges incurred by FOXWELL in repairing or replacing the defective parts. 2 The customer shall have no coverage or benefits under this limited warranty if any of the following conditions are applicable: a) The product has been subjected to abnormal use, abnormal conditions, improper storage, exposure to moisture or dampness, unauthorized modifications, unauthorized repair, misuse, neglect, abuse, accident, alteration, improper installation, or other acts which are not the fault of FOXWELL, including damage caused by shipping. b) The Product has been damaged from external causes such as collision with an object, or from fire, flooding, sand, dirt, windstorm, lightning, earthquake or damage from exposure to weather conditions, an Act of God, or battery leakage, theft, blown fuse, improper use of any electrical source, or the product was used in combination or connection with other product, attachments, supplies or consumables not manufactured or distributed by FOXWELL. 3 The customer shall bear the cost of shipping the product to FOXWELL. And FOXWELL shall bear the cost of shipping the product back to the customer after the completion of service under this limited warranty. 4 FOXWELL does not warrant uninterrupted or error-free operation of the product. If a problem develops during the limited warranty period, the consumer shall take the following step-by-step procedure: a) The customer shall return the product to the place of purchase for repair or replacement processing, contact your local FOXWELL distributor or visit our website www.foxwelltech.us to get further information. b) The customer shall include a return address, daytime phone number and/or fax number, complete description of the problem and original invoice specifying date of purchase and serial number. c) The customer will be billed for any parts or labor charges not covered by this limited warranty. d) FOXWELL will repair the Product under the limited warranty within 30 days after receipt of the product. If FOXWELL cannot perform repairs covered under this limited warranty within 30 days, or after a reasonable number of attempts to repair the same defect, FOXWELL at its option, will provide a replacement product or refund the purchase price of the product less a reasonable amount for usage. e) If the product is returned during the limited warranty period, but the problem with the product is not covered under the terms and conditions of this limited warranty, the customer will be notified and given an estimate of the charges the customer must pay to have the product repaired, with all shipping charges billed to the customer. If the estimate is refused, the product will be returned freight collect. If the product is returned after the expiration of the limited warranty period, FOXWELL’ normal service policies shall apply and the customer will be responsible for all shipping charges. 5 ANY IMPLIED WARRANTY OF MERCHANTABILITY, OR FITNESS FOR A PARTICULAR PURPOSE OR USE, SHALL BE LIMITED TO THE DURATION OF THE FOREGOING LIMITED WRITTEN WARRANTY. OTHERWISE, THE FOREGOING LIMITED WARRANTY IS THE CONSUMER’S SOLE AND EXCLUSIVE REMEDY AND IS IN LIEU OF ALL OTHER WARRANTIES, EXPRESS OR IMPLIED. FOXWELL SHALL NOT BE LIABLE FOR SPECIAL, INCIDENTAL, PUNITIVE OR CONSEQUENTIAL DAMAGES, INCLUDING BUT NOT LIMITED TO LOSS OF 2 NT6 X 4Elite Series User’s Manual_English_ V 1 . 0 3 ANTICIPATED BENEFITS OR PROFITS, LOSS OF SAVINGS OR REVENUE, LOSS OF DATA, PUNITIVE DAMAGES, LOSS OF USE OF THE PRODUCT OR ANY ASSOCIATED EQUIPMENT, COST OF CAPITAL, COST OF ANY SUBSTITUTE EQUIPMENT OR FACILITIES, DOWNTIME, THE CLAIMS OF ANY THIRD PARTIES, INCLUDING CUSTOMERS, AND INJURY TO PROPERTY, RESULTING FROM THE PURC HASE OR USE OF THE PRODUCT OR ARISING FROM BREACH OF THE WARRANTY, BREACH OF CONTRACT, NEGLIGENCE, STRICT TORT, OR ANY OTHER LEGAL OR EQUITABLE THEORY, EVEN IF FOXWELL KNEW OF THE LIKELIHOOD OF SUCH DAMAGES. FOXWELL SHALL NOT BE LIABLE FOR DELAY IN RENDERING SERVICE UNDER THE LIMITED WARRANTY, OR LOSS OF USE DURING THE PERIOD THAT THE PRODUCT IS BEING REPAIRED. 6. Some states do not allow limitation of how long an implied warranty lasts, so the one-year warranty limitation may not apply to you (the Consumer). Some states do not allow the exclusion or limitation of incidental and consequential damages, so certain of the above limitations or exclusions may not apply to you (the Consumer). This limited warranty gives the Consumer specific legal rights and the Consumer may also have other rights which vary from state to state. 3 NT6 X 4Elite Ser…

Text truncated - open the document above for the full version.

ShenzhenFoxwellTechnologyCo.,Ltd 2.911(d)(5)(i)EquipmentTypeAttestationv1.2 Section2.911(d)(5)(i)Certification–EquipmentType Companyname:ShenzhenFoxwellTechnologyCo.,Ltd Address:5/F,PlantC,Baocheng71stZone,Xin'anStreet,BaoanDistrict,ShenzhenChina 518106 ProductName:AUTOMOTIVEDIAGNOSTICPLATFORM FCCID:2AXCX-2843L1123 Model(s):NT644Elitewireless,NT604Elitewireless,NT614Elitewireless, NT624Elitewireless,NT634Elitewireless,NT650Pro,NT680Prowireless, NT680wireless,NT680Litewireless,NT650Elitewireless,RS830Prowireless,NT510Elitewireless, NT530wireless,NT630Pluswireless 2.911(d)(5)(i)EquipmentType We,[ShenzhenFoxwellTechnologyCo.,Ltd](“theapplicant”)certifythattheequipmentforwhich authorizationissoughtthroughcertificationisnot:  Prohibitedfromreceivinganequipmentauthorizationpursuantto§2.903;oftheFCCrules.  Identifiedasanequipmenttypeinthe“CoveredList” NOTE1 Yourssincerely, Name:YalinYangDate:2023.12.12 TitleandCompanyname:Manager/ShenzhenFoxwellTechnologyCo.,Ltd NOTE1 “CoveredList”;istheListofEquipmentandServicesCoveredBySection2ofTheSecureNetworksAct,availableat https://www.fcc.gov/supplychain/coveredlist References; 1)986446D01CoveredEquipmentv01 https://apps.fcc.gov/oetcf/kdb/forms/FTSSearchResultPage.cfm?switch=P&id=325672 2)FederalRegisterdocument2022-28263publishedon02/06/23 https://www.federalregister.gov/documents/2023/02/06/2022-28263/protecting-against-national-security-threats-to-the-com munications-supply-chain-through-the

ShenzhenFoxwellTechnologyCo.,Ltd 2.911(d)(5)(ii)ApplicantAttestationv1.3 Section2.911(d)(5)(ii)Certification–Applicant(CoveredList) Companyname:ShenzhenFoxwellTechnologyCo.,Ltd Address:5/F,PlantC,Baocheng71stZone,Xin'anStreet,BaoanDistrict,ShenzhenChina 518106 ProductName:AUTOMOTIVEDIAGNOSTICPLATFORM FCCID:2AXCX-2843L1123 Model(s):NT644Elitewireless,NT604Elitewireless,NT614Elitewireless, NT624Elitewireless,NT634Elitewireless,NT650Pro,NT680Prowireless, NT680wireless,NT680Litewireless,NT650Elitewireless,RS830Prowireless,NT510Elitewireless, NT530wireless,NT630Pluswireless 2.911(d)(5)(ii)Applicantfiling We,[ShenzhenFoxwellTechnologyCo.,Ltd](“theapplicant”)certifythat,asofthedateofthefiling oftheapplication,theapplicantisnotidentified NOTE1 onthe“CoveredList” NOTE2 ,established pursuantto§1.50002ofthischapter,asanentityproducingcoveredcommunicationsequipment. Yourssincerely, Name:YalinYangDate:2023.12.12 TitleandCompanyname:Manager/ShenzhenFoxwellTechnologyCo.,Ltd NOTE1 Deleteoptionnotapplicabletothisapplication. NOTE2 “CoveredList”;istheListofEquipmentandServicesCoveredBySection2ofTheSecureNetworksAct,availableat https://www.fcc.gov/supplychain/coveredlist References; 1)986446D01CoveredEquipmentv01 https://apps.fcc.gov/oetcf/kdb/forms/FTSSearchResultPage.cfm?switch=P&id=325672 2)FederalRegisterdocument2022-28263publishedon02/06/23 https://www.federalregister.gov/documents/2023/02/06/2022-28263/protecting-against-national-security-threats-to-the-com munications-supply-chain-through-the

ShenzhenFoxwellTechnologyCo.,Ltd 2.911(d)(7)USAAgentv1.5 Section2.911(d)(7)USAAgentforServiceofProcess Companyname:ShenzhenFoxwellTechnologyCo.,Ltd Address:5/F,PlantC,Baocheng71stZone,Xin'anStreet,BaoanDistrict, ShenzhenChina518106 ProductName:AUTOMOTIVEDIAGNOSTICPLATFORM FCCID:2AXCX-2843L1123 Model(s):NT644Elitewireless,NT604Elitewireless,NT614Elitewireless, NT624Elitewireless,NT634Elitewireless,NT650Pro,NT680Prowireless, NT680wireless,NT680Litewireless,NT650Elitewireless,RS830Prowireless, NT510Elitewireless,NT530wireless,NT630Pluswireless 2.911(d)(7)USADesignatedAgentforServiceofProcess We,[Insertapplicantname](“theapplicant”)designate[StoneTradingLimited] NOTE1 forthepurposeofacceptingserviceofprocessonbehalfoftheapplicant. Applicantconsent:Weacknowledgeourconsenttoacceptserviceofprocessinthe UnitedStatesformattersrelatedtotheapplicableequipment,andatthephysicalU.S. addressandemailaddressofthedesignatedagentandacknowledgeour acceptanceofourobligationtomaintainanagentforserviceofprocessintheUnited Statesfornolessthanoneyearaftereitherwethegranteehavepermanently terminatedallmarketingandimportationoftheapplicableequipmentwithintheU.S., orattheconclusionofanyCommission-relatedadministrativeorjudicialproceeding involvingtheequipment,whicheverislater. Agentobligation:Weacknowledgeourobligationtoacceptserviceofprocessinthe UnitedStatesformattersrelatedtotheapplicableequipmentatourphysicalU.S. addressandemailaddressfornolessthanoneyearaftereitherthegranteehas permanentlyterminatedallmarketingandimportationoftheapplicableequipment withintheU.S.,orattheconclusionofanyCommission-relatedadministrativeor judicialproceedinginvolvingtheequipment,whicheverislater. USAAgent Companyname:StoneTradingLimited USAAddress:6547NAcademyBlvd #2266,ColoradoSprings,CO80918,United States FRNNumber ： 0033401936 ContactName:DongmeiFang TelephoneNo:+12134573118 Email:[email protected] Applicant Companyname:ShenzhenFoxwell TechnologyCo.,Ltd Address:5/F,PlantC,Baocheng71st Zone,Xin'anStreet,BaoanDistrict, ShenzhenCity,China.518106 GranteeFRNNumber:0029904422 FCCGranteeCode:2AXCX ContactName:YalinYang TelephoneNo:+86-0755-26697229 Email:[email protected] ShenzhenFoxwellTechnologyCo.,Ltd 2.911(d)(7)USAAgentv1.5 Signature: Title:manager Signature: Title:Manager Date:2023-12-11Date:2023-12-11 NOTE1:AnapplicantlocatedintheUnitedStatesmaydesignateitselfastheagentforservice ofprocess. Reference;FederalRegisterdocument2022-28263publishedon02/06/23 https://www.federalregister.gov/documents/2023/02/06/2022-28263/protecting-against-nation al-security-threats-to-the-communications-supply-chain-through-the

ShenzhenFoxwellTechnologyCo.,Ltd AgentAuthorization Company:ShenzhenFoxwellTechnologyCo.,Ltd Address:5/F,PlantC,Baocheng71stZone,Xin'anStreet,BaoanDistrict, ShenzhenChina518106 ProductName:AUTOMOTIVEDIAGNOSTICPLATFORM ModelNumber(s):NT644Elitewireless,NT604Elitewireless,NT614Elitewireless, NT624Elitewireless,NT634Elitewireless,NT650Pro,NT680Prowireless, NT680wireless,NT680Litewireless,NT650Elitewireless,RS830Prowireless, NT510Elitewireless,NT530wireless,NT630Pluswireless ProductDescription:AUTOMOTIVEDIAGNOSTICPLATFORM WeauthorizeMiCOMLabsInc.,575BoulderCourt,Pleasanton,California94566,USA, toactonourbehalfonallmattersconcerningthecertificationofabovenamed equipment. WedeclarethatMiCOMLabsInc.isallowedtoforwardallinformationrelatedtothe approvalandcertificationofequipmenttotheregulatoryagenciesasrequiredandto discussanyissuesconcerningtheapprovalapplication.Anyandallactscarriedoutby MiCOMLabsonourbehalfshallhavethesameeffectasactsofourown. Signature:Date:2023.12.12 Name:YalinYang Title:Manager Company:ShenzhenFoxwellTechnologyCo.,Ltd

ShenzhenFoxwellTechnologyCo.,Ltd OfficeofEngineeringTechnology FederalCommunicationsCommission 7435OaklandMillsRoad Columbia,MD21046 USA Date:2023.12.12 Subject;RequestforConfidentiality FCCID:2AXCX-2843L1123 ToWhomItMayConcern, PursuanttotheprovisionsoftheCommission’srulesTitle47Sections§0.457and§0.459,we arerequestingtheCommissiontowithholdthefollowingattachment(s)asconfidential documentsfrompublicdisclosureindefinitely. Thesedocumentscontaindetailedsystemandequipmentdescriptionsandareconsideredas proprietaryinformationinoperationoftheequipment.Thepublicdisclosureofthesedocuments mightbeharmfultoourcompanyandwouldgivecompetitorsanunfairadvantageinthemarket. SchematicDiagram BlockDiagram PartsList OperationalDescription Tune-upProcedure Inadditionaltoabovementioneddocuments,inordertocomplywiththemarketingregulations inTitle47CFR§2.803andtheimportationrulesinTitle47CFR§2.1204,whileensuringthat businesssensitiveinformationremainsconfidentialuntiltheactualmarketingofnewly authorizeddevices,werequestShortTermConfidentialityofthefollowingattachment(s); ExternalPhotos TestSetupPhotos InternalPhotos UserManual For45days,pursuanttoPublicNoticeDA04-1705. OR For180dayspursuanttoKDB726920D01. Itisourunderstandingthatallmeasurementtestreports,FCCIDlabelformatand correspondenceduringthecertificationreviewprocesscannotbegrantedasconfidential documentsandthisinformationwillbeavailableforpublicreviewoncethegrantofequipment authorizationisissued. Sincerely, Signature: Name:YalinYang Title:Manager

ShenzhenFoxwellTechnologyCo.,Ltd ModelDifference Productdescription:AUTOMOTIVEDIAGNOSTICPLATFORM Modelname:NT644Elitewireless,NT604Elitewireless,NT614Elitewireless, NT624Elitewireless,NT634Elitewireless,NT650Pro,NT680Prowireless, NT680wireless,NT680Litewireless,NT650Elitewireless, RS830Prowireless,NT510Elitewireless,NT530wireless, NT630Pluswireless TradeName:FOXWELL Onlythemodelnameisdifferent. Regards Sincerely Client’ssignature: Client’sname/title:YalinYang/Manager Contactinformation/address:5/F,PlantC,Baocheng71stZone,Xin'anStreet, BaoanDistrict,ShenzhenCity,China.518106

EUT PHOTO(External Photos)

Label & label location 20mm*10mm FCC ID: 2AXCX-2843L1123 Label location

EUT PHOTO(Internal Photos) ANT

FCC ID: 2AXCX-2843L1123 RF Exposure Evaluation According to KDB 447498 D01 General RF Exposure Guidance v06 and part 2.1093， Unless specifically required by the published RF exposure KDB procedures, standalone 1-g head or body and 10-g extremity SAR evaluation for general population exposure conditions, by measurement or numerical simulation, is not required when the corresponding SAR Test Exclusion Threshold condition(s), listed below, is (are) satisfied. For 100 MHz to 6 GHz and test separation distances ≤ 50 mm, the 1-g and 10-g SAR test exclusion thresholds are determined by the following: [(max. power of channel, including tune-up tolerance, mW) / (min. test separation distance, mm)] · [√f (GHz) ] ≤ 3.0 for 1-g SAR, and ≤ 7.5 for 10-g extremity SAR, where f (GHz) is the RF channel transmit frequency in GHz Power and distance are rounded to the nearest mW and mm before calculation The result is rounded to one decimal place for comparison Here, For 2.4G WIFI Mode Max Power(dBm) Max Power(mW) Frequency(MHz) Min. distance(mm) Calc. thresholds limit 802.11b 6.19 4.16 2462 5 1.31 3.0 802.11g 5.01 3.17 2462 5 0.99 3.0 802.11n20 3.65 2.32 2462 5 0.73 3.0 802.11n40 2.78 1.90 2452 5 0.60 3.0 For BT Mode Max Power(dBm) Max Power(mW) Frequency(MHz) Min. distance(mm) Calc. thresholds limit GFSK 0.025 1.01 2441 5 0.31 3.0 π/4-DQPSK 0.761 1.19 2441 5 0.37 3.0 8-DPSK 1.310 1.35 2441 5 0.42 3.0 For BLE Mode Max Power(dBm) Max Power(mW) Frequency(MHz) Min. distance(mm) Calc. thresholds limit GFSK -2.898 0.51 2440 5 0.16 3.0 Note: The 2.4G WIFI, BT and BLE are can not transmitting at the same time. So a SAR test is not required

Project No.: ZKT-2311279198E-1 Page 1 of 37 FCC TEST REPORT FCC ID:2AXCX-2843L1123 Report Number. .............................. : ZKT-2311279198E-1 Date of Test ................................................. : Nov. 27, 2023 to Dec. 05, 2023 Date of issue .................................... : Dec. 05, 2023 Total number of pages ...................... 37 Test Result ..................................... : PASS Testing Laboratory. ........................ : Shenzhen ZKT Technology Co., Ltd. Address .......................................... : 1/F, No. 101, Building B, No. 6, Tangwei Community Industrial Avenue, Fuhai Street, Bao'an District, Shenzhen, China Applicant's name ......................... : Shenzhen Foxwell Technology Co., Ltd Address .......................................... : 5/F, Plant C, Baocheng 71st Zone, Xin'an Street, Baoan District, Shenzhen City, China. 518106 Manufacturer's name ................... : Shenzhen Foxwell Technology Co., Ltd Address .......................................... : 5/F, Plant C, Baocheng 71st Zone, Xin'an Street, Baoan District, Shenzhen City, China. 518106 Test specification: Standard ........................................... : FCC CFR Title 47 Part 15 Subpart C Section 15.247 ANSI C63.10:2013 Test procedure ................................. : / Non-standard test method ............. : N/A Test Report Form No. .................... : / Test Report Form(s) Originator .... : ZKT Testing Master TRF .................................... : Dated: 2020-01-06 This device described above has been tested by ZKT, and the test results show that the equipment under test (EUT) is in compliance with the FCC requirements. And it is applicable only to the tested sample identified in the report. This report shall not be reproduced except in full, without the written approval of ZKT, this document may be altered or revised by ZKT, personal only, and shall be noted in the revision of the document. Product name ................................. : AUTOMOTIVE DIAGNOSTIC PLATFORM Trademark ...................................... : FOXWELL Model/Type reference......................: NT644Elite wireless NT604Elite wireless, NT614Elite wireless, NT624Elite wireless, NT634Elite wireless, NT650Pro, NT680Pro wireless, NT680 wireless, NT680Lite wireless, NT650Elite wireless, RS830Pro wireless, NT510Elite wireless, NT530 wireless, NT630Plus wireless Project No.: ZKT-2311279198E-1 Page 2 of 37 Testing procedure and testing location: Testing Laboratory ................................... : Shenzhen ZKT Technology Co., Ltd. Address ...................................................... : 1/F, No. 101, Building B, No. 6, Tangwei Community Industrial Avenue, Fuhai Street, Bao'an District, Shenzhen, China Jim Liu Tested by (name + signature) .................... : Jeff Fu Reviewer (name + signature) ..................... : Lake Xie Approved (name + signature) .................... : Project No.: ZKT-2311279198E-1 Page 3 of 37 Table of Contents Page 1.VERSION ......................................................................................................................................... 5 2. SUMMARY OF TEST RESULTS .................................................................................................... 6 2.1 TEST FACILITY ...................................................................................................................... 7 2.2 MEASUREMENT UNCERTAINTY .......................................................................................... 7 3. GENERAL INFORMATION ............................................................................................................ 8 3.1 GENERAL DESCRIPTION OF EUT ....................................................................................... 8 3.2 DESCRIPTION OF TEST MODES ......................................................................................... 9 3.3 BLOCK DIGRAM SHOWING THE CONFIGURATION OF SYSTEM TESTED ..................... 9 3.4 DESCRIPTION OF SUPPORT UNITS(CONDUCTED MODE) .............................................. 9 3.5 EQUIPMENTS LIST FOR ALL TEST ITEMS ........................................................................ 10 4. EMC EMISSION TEST ................................................................................................................. 12 4.1 CONDUCTED EMISSION MEASUREMENT ....................................................................... 12 4.1.1 POWER LINE CONDUCTED EMISSION Limits ......................................................... 12 4.1.2 TEST PROCEDURE .................................................................................................... 12 4.1.3 DEVIATION FROM TEST STANDARD ....................................................................... 12 4.1.4 TEST SETUP ............................................................................................................... 13 4.1.5 EUT OPERATING CONDITIONS ................................................................................ 13 4.2.1 Radiated Emission Limits ............................................................................................. 14 4.2.2 TEST PROCEDURE .................................................................................................... 15 4.2.3 DEVIATION FROM TEST STANDARD ....................................................................... 15 4.2.4 TEST SETUP ............................................................................................................... 15 4.2.5 EUT OPERATING CONDITIONS ................................................................................ 16 5.RADIATED BAND EMISSION MEASUREMENT ......................................................................... 21 5.1 Test Requirement: .......................................................................................................... 21 5.2 TEST PROCEDURE .....................................................…

Text truncated - open the document above for the full version.

Project No.: ZKT-2311279198E-3 Page 1 of 75 FCC TEST REPORT FCC ID:2AXCX-2843L1123 Report Number. .............................. : ZKT-2311279198E-3 Date of Test ................................................. : Nov. 27, 2023 to Dec. 05, 2023 Date of issue .................................... : Dec. 05, 2023 Total number of pages ...................... 75 Test Result ....................................... : PASS Testing Laboratory. ........................ : Shenzhen ZKT Technology Co., Ltd. Address .......................................... : 1/F, No. 101, Building B, No. 6, Tangwei Community Industrial Avenue, Fuhai Street, Bao'an District, Shenzhen, China Applicant's name ......................... : Shenzhen Foxwell Technology Co., Ltd Address .......................................... : 5/F, Plant C, Baocheng 71st Zone, Xin'an Street, Baoan District, Shenzhen City, China. 518106 Manufacturer's name ................... : Shenzhen Foxwell Technology Co., Ltd Address .......................................... : 5/F, Plant C, Baocheng 71st Zone, Xin'an Street, Baoan District, Shenzhen City, China. 518106 Test specification: Standard .......................................... : FCC CFR Title 47 Part 15 Subpart C Section 15.247 ANSI C63.10:2013 Test procedure ................................. : / Non-standard test method ............. : N/A Test Report Form No. .................... : / Test Report Form(s) Originator .... : ZKT Testing Master TRF .................................... : Dated: 2020-01-06 This device described above has been tested by ZKT, and the test results show that the equipment under test (EUT) is in compliance with the FCC requirements. And it is applicable only to the tested sample identified in the report. This report shall not be reproduced except in full, without the written approval of ZKT, this document may be altered or revised by ZKT, personal only, and shall be noted in the revision of the document. Product name ................................. : AUTOMOTIVE DIAGNOSTIC PLATFORM Trademark ...................................... : FOXWELL Model/Type reference ...................... : NT644Elite wireless NT604Elite wireless, NT614Elite wireless, NT624Elite wireless, NT634Elite wireless, NT650Pro, NT680Pro wireless, NT680 wireless, NT680Lite wireless, NT650Elite wireless, RS830Pro wireless, NT510Elite wireless, NT530 wireless, NT630Plus wireless Project No.: ZKT-2311279198E-3 Page 2 of 75 Testing procedure and testing location: Testing Laboratory ................................... : Shenzhen ZKT Technology Co., Ltd. Address ...................................................... : 1/F, No. 101, Building B, No. 6, Tangwei Community Industrial Avenue, Fuhai Street, Bao'an District, Shenzhen, China Jim Liu Tested by (name + signature) .................... : Jackson Fang Reviewer (name + signature) ..................... : Lake Xie Approved (name + signature) .................... : Project No.: ZKT-2311279198E-3 Page 3 of 75 Table of Contents Page 1. VERSION ....................................................................................................................................... 5 2. SUMMARY OF TEST RESULTS................................................................................................... 6 2.1 TEST FACILITY ........................................................................................................................... 7 2.2 MEASUREMENT UNCERTAINTY .............................................................................................. 7 3. GENERAL INFORMATION ........................................................................................................... 8 3.1 GENERAL DESCRIPTION OF EUT ............................................................................................ 8 3.2 DESCRIPTION OF TEST MODES .............................................................................................. 9 3.3 BLOCK DIGRAM SHOWING THE CONFIGURATION OF SYSTEM TESTED ........................ 10 3.4 DESCRIPTION OF SUPPORT UNITS(CONDUCTED MODE) ................................................ 10 3.5EQUIPMENTS LIST FOR ALL TEST ITEMS ............................................................................. 11 4. EMC EMISSION TEST ................................................................................................................ 13 4.1 CONDUCTED EMISSION MEASUREMENT ............................................................................ 13 4.1.1 POWER LINE CONDUCTED EMISSION LIMITS .................................................................. 13 4.1.2 TEST PROCEDURE ............................................................................................................... 13 4.1.3 DEVIATION FROM TEST STANDARD .................................................................................. 13 4.1.4 TEST SETUP .......................................................................................................................... 14 4.1.5 EUT OPERATING CONDITIONS ........................................................................................... 14 4.1.6 TEST RESULT ........................................................................................................................ 14 4.2 RADIATED EMISSION MEASUREMENT ................................................................................. 15 4.2.1 RADIATED EMISSION LIMITS .............................................................................................. 15 4.2.2 TEST PROCEDURE ............................................................................................................... 15 4.2.3 DEVIATION FROM TEST STANDARD .................................................................................. 16 4.2.4 TEST SETUP .......................................................................................................................... 16 4.2.5 EUT OPERATING CONDITIONS ................…

Text truncated - open the document above for the full version.

深 圳 市 众 成 通 讯 科 技 有 限 公 司 Shenzhen Zhongcheng Communication Technology Co., Ltd. Page 1 承认书 SPECIFICATION FOR APPROVAL 客户名称 CUSTOMER NAME ： 富士伟业 产品名称 PRODUCT NAME ： NT644Elite wireless 天线 客户料号 CUSTOMER P/N ： NT644Elite wireless 众成料号 ZC 料号 P/N: 8723DS-NT644REV:A MANUFACTURER SIGNATURE CUSTOMER SIGNATURE CHECKED BY： AUDITOR BY： APPROVED BY： DATE：2023-11-30 深 圳 市 众 成 通 讯 科 技 有 限 公 司 Shenzhen Zhongcheng Communication Technology Co., Ltd. Page 2 Contents ItemDescription 1.---------------------------------------------------- 产品图片 2.---------------------------------------------------- 规格表 3.---------------------------------------------------- 测试报告 4.---------------------------------------------------- 天线图 深 圳 市 众 成 通 讯 科 技 有 限 公 司 Shenzhen Zhongcheng Communication Technology Co., Ltd. Page 3 1. 产品图片 2. 规格表 : 主要技术指标Main technical specifications 频率范围（MHZ）2400-2500Frequency Range(MHZ)2400-2500 特性阻抗（Ω）50Impedance（Ω）50 增益（dbi） 0.8 1Gain(dbi) 0.8 1 输出电压驻波比<2.5VSWR<2.5 最大功率10WAdmitted Power10W 极化方式垂直级化PolarizationLinear Vertical 方向性全向性RadiationOmni-directional 3. 测试报告 3.1 Activetestdata Item Standard BandChannelFrequencyTRPTIS 1WIFI(AP)WIFI_B(11M)12412 14.59-77.53 2WIFI(AP)WIFI_B(11M)62437 14.15-76.76 3WIFI(AP)WIFI_B(11M)112462 13.56-74.91 深 圳 市 众 成 通 讯 科 技 有 限 公 司 Shenzhen Zhongcheng Communication Technology Co., Ltd. Page 4 3.2Passiveparameters Freq. (MHz)24002410242024302440245024602470248024902500 Gain (dBi) -1.49-1.44-0.79-0.76-0.61-0.69-0.25-0.190.170.190.81 Efficiency …

Text truncated - open the document above for the full version.